USER GUIDE 

Request free connector: www.trust.com/nI/support/connector-advisor/23925

Connector not working?
Request a compatible connector for free at:
www.trust.com/23925/freeconnector
refer to the “Safety & Usage guide” for more information

FAQ
WWW.TRUST.COM/23925/FAQ
Trust International BV – Laan van Barcelona 600 – 3317DD, Dordrecht, NL ©2020 Trust All rights reserved.

YBAR
PC Laptop
RGB

TRUST GXT 922 Gaming Mouse – USER’S MANUAL

Mouse Button layout

Installation

a- Open the internet browser and go to www.trust.com/24309/driver.
b- Click the “Download EXE” Mouse Button to download the software.
c- Click on the “24309_X.exe” and follow the installation wizard.
d- Click on the “TRUST GXT 922 Gaming Mouse” shortcut to start the software.
e- You can now start to configure the mouse. The manual will be referred to as ‘Save’ to update the mouse.
Updating the mouse can take up to 20 seconds depending on your system.

Mouse Button Programming

3. Assign a function
a- Click on the Button you want to re-assign
b- Click on the function you want to assign.
– Click on ‘Save’, the mouse is being updated.
At least one Mouse Button has to be assigned as “Left Click”.

Report rate & DPI settings
4. DPI setting
a- Click on the ‘DPI’ tab.
b- Click on the checkbox next to the DPI number to enable or disable this DPI level.
c- Choose a LED color for each DPI setting.
d- Click on the ‘DPI’ button.
e- Change the DPI level by dragging the respective bar.
– Click on ‘Save’, the mouse is being updated.

Light Settings

5. Change the Lighting
a- Click on the ‘LED’ tab.
b- Change the light mode.
c- Change the animation speed.
d- Change the direction.
– Click on ‘Save’, the mouse is being updated.

Other settings

6. Mouse Parameter
a- Click on the ‘DPI’ tab.
b- Change the Windows acceleration, Windows pointer speed, Windows scroll speed, or Windows double-click speed by dragging the respective cursor.
– Click on ‘Save’, the mouse is being updated.
7. Polling Rate
a- Click on the ‘DPI’’ tab.
b- Change the Polling rate by clicking on the respective frequency.
– Click on ‘Save’, the mouse is being updated.

Macro Settings

8. Create a Macro (Store a sequence of keys in the software)
a- Click on the ‘Macro Editor’ button.
b- Click on ‘New macro’ to create a new macro.
c- Set the delay time between each action and/or the loop/repeat setting.
d- Click ‘Record’ to Record the macro. Now enter your preferred macro sequence.
e- Click ‘Stop’ to Stoping the macro. (max. 112 actions)
– The created macro is now available under the ‘Macro’ function.
To assign a macro to follow step 3 of this manual.

Profile Settings
9. Select, Save or Load a profile
a- Select one of the 4 profiles by clicking on the preferred profile.
b- Click on ‘Export’ to save a setup, Click on ‘Import’ to load a setup.
c- Enter a name for the mouse setup you want to save or choose the preferred profile to load.
d- Click on ‘Save’ to save the setup, click on ‘Open’ to load the setup.
– Click on ‘Save’ → Your mouse setup is now saved or updated to your mouse.
10. Reset default settings
a- Click on ‘RESET’ to reset the current profile to factory default.
b- Click on ‘Save’ to reset the current profile to factory default.

Troubleshooting

If your problem is not solved, please contact the help desk at www.trust.com/24309/faq

Trust Wireless Mouse Instructions

Product overview

• Frequently asked questions
• Domande frequenti
• Preguntas frecuentes
• Veelgestelde vragen
• Foire aux questions
• Haufig gestellte Fragen
  www.trust.com/18519/faq

USER MANUAL
ZIGBEE SMOKE DETECTOR
ZSDR-850

Item 71197 Version 1.0
Visit www.trust.com/zigbee for the latest instructions

www.trust.com/zigbee

COMPATIBILITY

This photoelectric smoke detector works with the Z1 Zigbee Bridge and the ICS-2000 to give additional functionality like receiving
push notifications when smoke is detected. NOTE: For receiving push notifications, a fully working internet connection is required.

PLACING THE SMOKE DETECTOR

• Place the detector on the ceiling. In case of a sloped ceiling, place 90 cm from the highest point.
• To ensure that the sound can be clearly heard in bedrooms, the smoke detector must be placed no further than 3 meters from a bedroom door.
• It is recommended to install a smoke detector on every floor of your home
• Place the detector at least 2m away from cooking appliances
• Relocate the unit if it produces frequent false alarms
• Do not place the smoke detector near exhaust fans or airconditioning systems as they can prevent smoke from reaching the smoke detector
• Avoid placing the detector in bathrooms and other  very humid or dusty places
• Always comply with the local regulations for installation in buildings.

TESTING AND USAGE

• Always test the detector using the test mode after placement and after that once a week.
• Test the detector once a week. Replace the detector immediately when the test fails.
• Replace the battery immediately when the detector is indicating battery low. (up to 3-year battery life)
• Clean the detector once a month with a soft brush
• Never use water, cleaners, or solvents to clean the detector since they may damage the unit.
•  If the detector is damaged replace it immediately.
• The smoke detector will not alert hearing-impaired residents. It is recommended to install special smoke detectors to alert hearing-impaired residents.
• Never use an open flame of any kind to test this unit. You might accidentally damage or set fire to the unit or to your home.
• Use only a CR123A 3.0V Lithium Battery. Other batteries may cause unreliable operation.
•  Removal of the battery will render this alarm inoperative
• Press test button to check operation after replacing the battery.
  Check www.trust.com/71197 for the latest instructions

1. REMOVE BATTERY PULL STRIP
   A. Remove the detector from the mounting bracket by twisting it.
   B. Remove the battery pull strip by pulling it from the detector.
   Only after removing the pull strip, the detector can be used.
2.  INDICATORS
   The detector contains a LED indicator to show the status of the detector. Please see below the meaning of the different LED
   indications.

   LED FUNCTION TABLE

   Connection mode	LED will flash fast for approximately 1 min.
   Connected successfully	LED will light up for 3 sec (The App will also indicate when the connection is successful)
   Detector reset	LED will flash 6x
   Detector alarm	The LED will flash and the detector will sound (85db). To stop the detector alarm press the Test/Stop button
   Detector operation	LED will flash once every 53 sec to indicate the detector is operating correctly
   Battery low indication	LED will flash once and gives one beep every 53 sec

3. DOWNLOAD APP
   To connect the detector with a Z1 Zigbee bridge or ICS-2000, first, get the App by scanning the QR code or go to trust.com/ Zigbee and install it.
4. CONNECT DETECTOR
   A. In the App, select a room, press the + button and choose Trust Zigbee line/ Smoke detector and follow the instructions. For manual set up of push-notifications go to the rules tab, press the + button, and select notification wizard.
5. MOUNT THE DETECTOR
   A Mount the bracket of the detector on a flat surface on the ceiling and secure it with the included screws.
   B 1 Place the detector on the mounting bracket.
   2 Secure the detector by twisting it on the bracket to lock it.
6. TEST MODE
   Activate the test mode of the detector to check the operation by pressing the Test/Stop button. The LED will flash fast and the detector will sound.

RESET DETECTOR AND ACTIVATE CONNECT MODE
Warning: This step will disconnect the detector from the Z1 Zigbee Bridge or the ICS-2000. To reset the detector press the button in the hole at the side for approximately 5 sec with the included pin. The LED will flash 6x to confirm the reset.
Activate connect mode: After resetting the detector you can activate the connect mode by pressing the button in the hole on the side for approx.
2 sec. The LED will flash fast for 1 minute to indicate the connection mode.
REPLACE BATTERY
A. Open the battery compartment by removing the detector from the bracket.
B. Remove the empty battery and insert a new 3V CR123A lithium battery in the compartment. Note the positive and negative polarity.
C. Lock the detector back on the bracket. Test if the battery is placed correctly by activating the test mode.
(See step 6).

DISCLAIMER
This product is used as a warning device to aid the user in detecting the presence of smoke. However, it remains the responsibility of the end user to prevent, detect and/or extinguish a (smoldering) fire or smoke from accumulating. Therefore Trust cannot be held responsible or liable for any damages or injuries resulting from fire, smoke orheat or any subsequent damages.
www.trust.com/zigbee

Package Contents

CONNECTION

PC – 5.1 Surround

Console – 5.1 Surround (PS4)

Console – 5.1 Surround (XBOX ONE)

Other – Stereo