electric bottle warmer
INSTRUCTIONS FOR USE

IMPORTANT WARNINGS!

Keep this instruction sheet for future reference as it includes important information.

• This appliance is intended for household use only. Do not use the outdoors.
• Before plugging in the Bottle Warmer for the first time ensure that the voltage is compatible with your electricity supply by checking the label on the base of the unit.
• Ensure water has been added to the unit before switching the unit on.
• Do not immerse in water, to protect against fire, electric shock, and injury to persons. Do not immerse cord, plugs or other parts of the unit in water or other liquid.
• Misuse of the product may result in the risk of fire, electric shock, and/or personal injury.
• This appliance can be used by children aged from 14 years and above if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Cleaning and user maintenance shall not be made by children unless they are aged 14 years and above and supervised.
• Keep the appliance and its cord out of reach of children aged less than 3 years.
• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
• Children shall not play with this appliance.
• The heating element surface is subject to residual heat after use.
• Do not touch hot surfaces use handles and knobs.
• Ensure that the heating guidelines are followed to ensure that the food is not heated for too long.
  For your child’s safety – Always check food temperature before feeding by testing on a sensitive part of your skin.
• Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. If the supply cord is damaged it must be changed by a qualified person in order to avoid a hazard. If the damage is from new the unit must be returned to the manufacturer.
• If within a retail warranty period this product should be exchanged at place of purchase. The manufacturer will then be made aware. Any questions? Visit our website www.tommeetippee.com
• Always use on a flat heat resistant surface.
• Do not move appliance when in use.
• Do not let the cord hang over edge of kitchen work surface or touch hot surfaces. The product has been fitted with a cord wind on the base of the unit to allow you to adjust the length of the cord safely. It is recommended that the cord be kept as short as possible.
• Do not use any accessories other than those supplied with this appliance.

HOW TO USE

The speed at which the warmer heats the milk or food will depend on the size of the bottle or container and the starting temperature of the milk or food (e.g. room temperature 20˚C or from the refrigerator 5˚C).
We recommend that setting 3 is always used for heating up, and settings 2 and 1 are used for keeping warm only.
MILK OR FOOD SHOULD NOT BE HEATED FOR OVER 30 MINUTES.
The guide gives an indication of the time you can expect the warmer to take. Maximum average stabilised temperature is approximate 85˚C

FOR FEEDING BOTTLES

1. Place filled bottle in warmer.
2. Fill the warmer with water to approximately 10mm below the rim of the warmer. Never let the water overflow or rise
   above the neck of the bottle. For larger bottles, fill to 12mm below the rim of the warmer.
3. Before plugging in, make sure the bottle warmer is switched to the “MIN” setting.
4. Plug in unit. The amber light will turn on to indicate the warmer is switched on and is heating up.
5. Turn dial to setting 3.
6. Once the water is heated, the amber light will switch off to indicate that the thermostat will maintain the temperature
   of the water. It does not indicate that the milk is ready.
7. Heat the milk to the desired temperature. Ensure that the heating guidelines are followed to ensure that the food is
   not heated for too long.
8. Take care when removing the bottle, as it and the surrounding water will be hot.
9. For your child’s safety – Always check food temperature before feeding by testing on a sensitive part of your skin.
   Take care not to overheat the milk.
10. In betwee can be placed back in the warmer to keep milk warm. The thermostat will maintain the temperature of the
    water. In doing this the indicator light will switch to amber to indicate the warmer is heating up.
11. Turn back the dial to the lowest setting and unplug the unit after feeding.

FOR BABY JARS

1. Remove the lid and place jar in warmer.
2. Fill the warmer with water to approximately 10mm below the rim of the warmer.
3. Before plugging in, make sure the bottle warmer is switched to the lowest setting.
4. Plug in the unit. The amber light will turn on to indicate the warmer is switched on and is heating up.
5. Turn dial to preferred setting.
6. Once the water is heated, the amber light will switch off to indicate that the thermostat will maintain the temperature of the water. It does not indicate that the food is ready. To ensure that the food stays at the temperature you have selected, the thermostat will maintain the temperature of the water. In doing this the indicator light may switch to amber whilst you are heating the food.
7. Heat food to the desired temperature. Ensure that the heating guidelines are followed to ensure that the food is not heated for too long.
8. Take care when removing the jar, as the surrounding water will be hot.
9. For your child’s safety – Always check food temperature before feeding by testing on a sensitive part of your skin.
   Take care not to overheat the food.
10. In between feeding, the jar can be placed back in the warmer to keep milk warm. The thermostat will maintain the temperature of the water. In doing this the indicator light will switch to amber to indicate the warmer is heating up.
11. Turn back dial to the lowest setting and unplug the unit after feeding.

HOW TO CLEAN THE ELECTRIC BOTTLE WARMER

Unplug and allow to cool before cleaning. Wipe with a damp cloth only. Do not clean with abrasive cleaners or allow to come into contact with solvents or harsh chemicals, damage could result.

DE-SCALING

De-scale your bottle warmer every 4 weeks to ensure it continues to work efficiently. To de-scale, your bottle warmer, use de-scaling sachets, following the manufacturer’s instructions on the pack carefully.

INFORMATION ON THE DISPOSAL FOR WASTE ELECTRICAL & ELECTRONIC EQUIPMENT (WEEE)
This symbol on the products and accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper disposal for treatment, recovery and recycling, please take these products to designated collection points where they will be accepted on a free of charge basis. In some countries you may be able to return your products to your local retailer upon the purchase of a new product.
Disposing of this product correctly will help you save valuable resources and prevent any possible effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest collection point for WEEE.
Penalties may be applicable for the incorrect disposal of this product in accordance with national legislation.
The product is fitted with a BS 1363 mains plug containing a fuse. If it ever becomes necessary to replace the fuse, only use fuses that are marked BS 1362, and rated at 13A. In the unlikely event that this plug is not suitable for the sockets in your home, it should be removed and a suitable plug fitted as follows:
The wires of the mains lead are coloured in accordance with the following code:
GREEN AND YELLOW – EARTH
BLUE – NEUTRAL
BROWN – LIVE
As these colours may not correspond with the coloured markings sometimes used to identify the terminals in the plug, connect as follows.
The wire coloured GREEN AND YELLOW must be connected to the terminal marked E or by the earth symbol or coloured GREEN or GREEN AND YELLOW. The wire coloured BLUE must be connected to the terminal marked N or coloured BLACK. The wire coloured BROWN must be connected to the terminal marked L or coloured RED.
If you are in any doubt about how to wire a plug or replace a fuse safely, consult a qualified electrician.
WARRANTY: This product has 12 months warranty period after the date of purchase.
If you have any questions please visit our website www.tommeetippee.com
Nothing in this warranty shall be construed as removing or limiting a consumers rights in law.
Jackel International Limited trading as Mayborn Group.
Northumberland Business Park West, Cramlington, Northumberland NE23 7RH, UK
Copyright © Jackel International Limited 2016.
TOMMEE TIPPEE is a registered trademark of Jackel International Limited.
422144

food and bottle warmer
INSTRUCTIONS FOR USE

IMPORTANT SAFEGUARDS READ ALL INSTRUCTIONS FOR HOUSEHOLD USE ONLY

When using electrical appliances, basic safety precautions should always be followed including the following:

• Do not touch hot surfaces, use handles and knobs.
• Always use on a flat heat resistant surface.
• To protect against fire, electric shock and injury to persons do not immerse cord, plugs or other parts of the unit in water or other liquid.
• When in use the food and bottle warmer contains hot water and steam.
• Extreme caution must be used when moving an appliance containing hot oil or other hot liquids.
• Always keep the food and bottle warmer and it’s plug out of reach of small children
• Before plugging in the food and bottle warmer for the first time ensure the voltage is compatible with your electricity supply by checking the label on the base of the unit.
• Ensure water has been added to the unit before switching the unit on.
• The product has been fitted with a cord wind on the base of the unit to allow you to adjust the length of the cord safely. It is recommended that the cord be kept as short as possible.
• User maintenance other than cleaning or descaling is not required for this product.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Do not place on or near a hot gas or electric burner or in a heated oven.
• Close supervision is necessary when any appliance is used by or near children.
• Unplug from the outlet when not in use and before cleaning. Allow cooling before putting on or taking off parts and before cleaning the appliance.
• Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair, or adjustment.
• The use of accessory attachment is not recommended by the appliance manufacturer as this may result in fire, electric shock or injury to persons.
• Do not use outdoors.
• Do not let cord hang over edge of table or counter or touch hot surfaces.
• Always attach the plug to the unit first, and then plug into the wall outlet. To disconnect turn any control “off” then remove the plug from the wall outlet.
• Do not use appliance for anything other than intended use.
• Before serving, unplug cord from wall outlet and dish. Do not leave cord within child’s reach.
• Always place the bottle or food jar into the warmer before adding the water.
• Ensure that the heating gui ted for too long.
• When the milk or food has reached the desired temperature, remove immediately. If left in the warmer,  the temperature of the milk or food will continue to increase.
• Before serving be sure food is at safe temperature.
• Do not move appliance when in use.
• A short power-supply cord is provided to reduce the risks resulting from becoming entangled in or tripping over a longer cord.
• Extension cords (or longer detachable power-supply cords) are available and may be used if care is exercised in their use.
• If an extension cord is used:
• The marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance;
• If the appliance is of the grounded type, the extension cord should be a grounding-type 3-wire cord; and
• The longer cord should be arranged so that it will not drape over the countertop or tabletop where it can be tripped over, snagged, or pulled on unintentionally (especially by children).

SAVE THESE INSTRUCTIONS

USAGE
The speed at which the food and bottle warmer heats the milk or food will depend on the size of the bottle or container and the starting temperature of the milk or food (e.g. room temperature 70°F or from the refrigerator 40˚F).
We recommend that setting is always used for heating up, setting is used for keeping warm only. Setting is
a MIN setting and should not be used.
MILK OR FOOD SHOULD NOT BE HEATED FOR OVER 30 MINUTES.
The guide gives an indication of the time you can expect the warmer to take. Maximum average stabilized temperature
is approximately 185 °F

FOR FEEDING BOTTLES

1. Place filled bottle in the food and bottle warmer.
2. Fill the food and bottle warmer with water to the inside edge using a jug or bottle (unless using a 5 oz bottle). For a smaller bottle fill to the underside of the screw ring. Never let the water overflow or rise above the neck of the bottle.
3. Before plugging in, make sure the food and bottle warmer is switched to the setting. Ensure your hands are dry.
4. Plug in the unit to the mains and switch the mains on. The amber light will turn on to indicate the food and bottle warmer is switched on and is heating up.
5. Turn dial to setting.
6. Once the water is heated, the amber light will switch off to indicate that the thermostat will maintain the temperature of the water. It does not indicate that the milk is ready. Please refer to the timings table in this manual to find out how long the milk should be heated for.
7. Heat the milk to the desired temperature. Ensure that the heating guidelines are followed to ensure that the milk is not heated for too long.
8. Take care when removing the bottle, as it and the surrounding water will be hot.
9. For your child’s safety always check milk temperature before feeding by testing on a sensitive part of your skin. Take care not to overheat the milk. Gently agitate the bottle prior to feeding.
10. During feeds the bottle can be placed back in the warmer to keep milk warm by using setting. The thermostat will maintain the temperature of the water. In doing this the indicator light will switch to amber to
    indicate the warmer is heating up.
11. Turn back the dial to setting and unplug the unit after feeding.
12. Empty the unit of any water and wipe dry.

FOR BABY JARS

1. Remove the lid and place jar in the food and bottle warmer.
2. Fill the food and bottle warmer with water to the inside edge using a jug or bottle. Ensure the water level is lower than the rim of the jar.
3. Before plugging in, make sure the food and bottle warmer is switched to the setting.
4. Plug in the unit. The amber light will turn on to indicate the food and bottle warmer is switched on and is heating up.
5. Turn dial to setting to heat up food.
6. Once the water is heated, the amber light will switch off to indicate that the thermostat will maintain the temperature of the water. It does not indicate that the food is ready. To ensure that the food stays at the temperature you have selected, the thermostat will maintain the temperature of the water. In doing this the indicator light may switch to amber whilst you are heating the food.
7. Heat food to the desired temperature. Ensure that the heating guidelines are followed to ensure that the food is not heated for too long. Please refer to table provided in this leaflet.
8. Take care when removing the jar, as the surrounding water will be hot.
9. For your child’s safety – Always check food temperature before feeding by testing on a sensitive part of your skin. Take care not to overheat the food.
10. During feeds, the jar can be placed back in the food and bottle warmer to keep food warm by using setting. The thermostat will maintain the temperature of the water. In doing this the indicator light will switch to amber to
    indicate the warmer is heating up.
11. Turn back the dial to setting and unplug the unit after feeding.
12. Empty the unit of any water and wipe dry.

INITIAL TEMPERATURE OF  FOOD
SETTING
FROM FRIDGE 40˚F (5˚C)	5 minutes	9 minutes	15 minutes	20 minutes
ROOM TEMP 70˚F  (20˚C)	4 minutes	6 minutes	8 minutes	14 minutes

CLEANING
Unplug and allow to cool before cleaning. After each use pour away remaining water from the food and bottle warmer base by tipping the food and bottle warmer sideways over a sink and wipe clean with a damp cloth only. Do not clean with abrasive cleaners or allow to come into contact with solvents or harsh chemicals, damage could result.

DE-SCALING
The frequency of de-scaling should be as follows:
Hard water – 7 days
Medium – 14 days
Soft – 21 days
You can find out your water quality via your water provider. Unplug the food and bottle warmer and allow to cool before cleaning. After each use pour away remaining water from the food and bottle warmer base by tipping the food and bottle warmer sideways over a sink and wipe clean with a damp cloth only. A build-up of limescale can negatively affect the performance of the food and bottle warmer. We recommend carrying out the descaling process as per the above frequency guidelines to ensure the food and bottle warmer continues to work efficiently. Living in a hard water area can produce limescale quicker than other areas therefore descaling is required sooner.  Use a descaler that is suitable for use with stainless steel and use as per the manufacturer’s guidelines. Alternatively, you can use white vinegar to descale your food and bottle warmer, please use as per manufacturer’s guidelines. Once you have descaled then follow instructions under set up to perform a final cleaning cycle. You may need to repeat the process if you find that limescale is still present.  DO NOT use metal objects or scourers to clean your food and bottle warmer. DO NOT use bleach to clean the food and bottle warmer. DO NOT use abrasive or anti-bacterial materials.

Mayborn USA Inc, dba Mayborn Group
1010 Washington Blvd, 11th Floor
Stamford, CT 06901

Copyright@ Mayborn USA Inc. 2018
Made in China.
Model number: 1150. 120v~ 60Hz 480W.

Any questions?
Visit our website
tommeetippee.com

SPECIFICATION

FAQS

What should I do if the appliance malfunctions or has been damaged in any manner?

Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return the appliance to the nearest authorized service facility for examination, repair, or adjustment.

Can I use this product outdoors?

No, this product is not intended for outdoor use.

How do I know when the milk or food is ready?

Once the water is heated, the amber light will switch off to indicate that the thermostat will maintain the temperature of the water. It does not indicate that the milk or food is ready. Please refer to the timings table in the manual to find out how long the milk or food should be heated for.

How do I keep milk or food warm during feeds?

During feeds, the bottle or jar can be placed back in the warmer to keep milk or food warm by using the setting. The thermostat will maintain the temperature of the water.

Can I use an extension cord with this product?

Extension cords may be used if care is exercised in their use. The marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance, and if the appliance is of the grounded type, the extension cord should be a grounding-type 3-wire cord.

How do I clean and descale the product?

After each use, pour away remaining water from the food and bottle warmer base by tipping it sideways over a sink and wipe clean with a damp cloth only. The frequency of descaling should be based on your water hardness level.

How long should I heat up milk or food for?

The guide gives an indication of the time you can expect the warmer to take. Milk or food should not be heated for over 30 minutes.

How do I use the product for feeding bottles and baby jars?

For feeding bottles, place the filled bottle in the food and bottle warmer and fill the warmer with water to the inside edge. For baby jars, remove the lid and place the jar in the food and bottle warmer, filling it with water to the inside edge.

How do I know if the voltage is compatible with my electricity supply?

Before plugging in the food and bottle warmer for the first time, ensure the voltage is compatible with your electricity supply by checking the label on the base of the unit.

What safety precautions should be followed when using the Tommee Tippee Food and Bottle Warmer?

Basic safety precautions should always be followed, such as not touching hot surfaces, using the product on a flat, heat-resistant surface, and keeping the product and its plug out of reach of small children.

tommee tippee 0570003 No-Touch Forehead Thermometer Instruction Manual

PRODUCT OVERVIEW

CONTACT US

tommeetippee.com

Manual Breast Pump
INSTRUCTIONS FOR USE

www.tommeetippee.cn

Parts Guide
A. Silicone insert
B. Horn
C. Pump Body
D. Valve (Spare included)
E. Bottle

closer to nature® manual breast pump

Please read and retain this important information for future reference.
Researched and developed by specialists and breastfeeding experts to express milk for storage and later use.
PARTS GUIDE (see diagram A)
How to put together your TommeeTippee* breast pump
A. Silicone insert
B. Horn
C. Pump body
D. Valve (spare Included)
E. Bottle

BEFORE USE ENSURE THE BREAST PUMP HAS BEEN DISASSEMBLED, WASHED AND STERILISED.
WARNING! Keep this Breast Pump away from children. Your child may choke on small parts.
DISASSEMBLING THE MANUAL BREAST PUMP

1. Unscrew bottle from the pump body.
2. Pull horn from pump body.
3. Pull off valve.

IT IS NOT ESSENTIAL TO TAKE THE SILICONE INSERT OUT OF THE HORN FOR CLEANING UNLESS MILK OR DIRT HAS BECOME TRAPPED INSIDE. IF SO, UNCLIP LIP FROM CUP AND PULL APART.
CLEANING AND STERILISING

• Wash in warm soapy water and rinse in clean water or use a dishwasher (Top shelf only). Do not clean with solvents or harsh chemicals.
• Do not allow product to come into contact with oil based foods (e.g. oil/tomato based sauces) as staining will occur.
• Suitable for sterilisation by steam (electric or microwave), boiling or cold water tablet/liquid sterilisation. Follow the steriliser manufacturers instructions. If using the steriliser Box follow instructions in section “Using the Steriliser Box”

ASSEMBLING THE MANUAL BREAST PUMP

1. Ensure all parts of breast pump have been washed and sterilised.
2. Wash your hands thoroughly before handling the pump.
3. Push horn onto pump body.
4. Push valve into place at the bottom of the pump body.
5. Attach bottle to pump body. It is possible for the valve to seal closed during storage and cleaning.

USING THE MANUAL BREAST PUMP

1. Wash your hands before touching the breast pump or your breasts and avoid touching inside the breast pump or the storage pot.
2. Find a comfortable chair where you can relax.
3. Hold the pump in whichever hand is most comfortable. Press the cup firmly against your breast so that It creates a seal all the way round. IF AIR CAN GET IN THERE WILL BE NO SUCTION.
4. Gently squeeze the handle and you will feel the suction. Release the handle and allow it to return to Its resting position. Releasing the handle opens the valve so that the milk can flow Into the bottle. Try to Imitate the rhythm of your baby as he sucks. You won’t need to squeeze hard – Just as much as Is comfortable. When you first start expressing mllk, use the pump for only 3-5 minutes on each breast. Over time you will be able to build up to 10-15 minutes on each breast.
5. You can help stimulate your milk flow by gently stroking your breast
6. Your milk will start to be released in drops and will gradually bulld up to a stream. First you will release yoursforemillt a thin yellowish liquid. This will be followed by your:thinemilk which resembles skimmed milk. Don’t worry that it looks thin and watery – both fore and hind milk are ideal for your baby and rich in nutrients.
7. The amount of milk you express and the time Ft takes will vary – don’t worry, thls is normal. Usually you will express 30-75m is (1-3oz) at a time, and it may take up to 30 minutes to drain a full breast. The first few times you express, the quantity may be less than this.
8. After use, take the pump apart and wash it to remove milk deposits. You do not need to sterilise your pump until you are ready to use it again.
9. Cover and store the expressed milk for later use.

FOR HYGIENE REASONS THIS PRODUCT CANNOT BE RETURNED ONCE OPENED UNLESS FAULTY.

HELPFUL ADVICE

• The best time to use your breast pump Is after the first feed of the day (unless otherwise advised by your breastfeeding advisor)
• Be comfortable and relax, e.g. watch the TV or have your favourite music playing.
• Remember you are only trying to express milk from Just behind the nipple – strong suction is not necessary.
• If water gets inside the pump body during sterilisation, simply lift the handle slightly and pour out the water.
• There should be no pain using your breast pump. If you feel pain, try using the pump more gently. Then examine your breasts. If there are any red or hot areas contact your breastfeeding advisor as soon as possible.
• Do not continue to use the pump once your milk has stopped flowing.
• Wash all breastfeeding equipment after use and before sterilisation.

THE CLOSER TO NATURE’ MANUAL BREAST PUMP CAN ONLY BE USED WITH TOMMEET1PPEE •CLOSERTONATURE •PPSU BOTTLES. A SEPARATE INSTRUCTION SHEET ON HOW TO CLEAN AND STERILISE THE TOMMEE YIPPEE’ CLOSERTO NATURE • BOTTLE IS ENCLOSED. PLEASE READ AND RETAIN THIS IMPORTANT INFORMATION FOR FUTURE REFERENCE.

USING THE STERILISER BOX

The Sterilising box has been specifically designed to microwave steam sterilise all of your breastfeeding equipment quickly and efficiently.
To use:

1. Pour 100m1 of water into sterilising box
2. Load upturned bottle, disassembled breast pump and any accessories.
3. Securely fit box lid
4. Open valve, on lid of box
5. Place steriliser box in microwave
6. Follow instructions according to microwave output
7. CAUTION:To avoid risk of burning, a ways ensure box is cool to touch before lifting out
8. Immediately fit valve on lid to make box airtight and sterile.

For use with the Tom met Tipper closer to nature breast pumps
HOW TO USE

1. Ensure pot is clean and sterilised.
2. Place pot inside of bottle.
3. Screw bottle onto pump body and continue to follow assembly of breast pump instructions.
4. When the breast pump is fully assembled and in use, the pot will hold up to 60m1 / 2oz.
5. Once you have expressed 60m1 stop pumping, place lid on storage pot and remove from bottle.
6. Store pot in either the fridge or freezer. See storage guide.
7. If you want to continue expressing, either Insert another clean and sterilised pot or express directly into the bottle of the breast pump

STORAGE OF BREAST MILK

a. You will notice that stored milk separates out into layers. Shake to remix thoroughly before feeding.
b. When freezing milk, allow space at the top of the bottle for expansion. It is easiest to freeze milk in individual feed quantities of 60-12Sml (2-4 oz).
c. Thaw frozen milk in the fridge or by standing the bottle in lukewarm water until it has reached body temperature. d. If you want to take expressed milk with you when you are out make sure it stays cold or frozen until needed.

WARNING!
Always use this product with adult supervision. Accidents have occurred when babies have been left alone with drinking equipment due to the baby falling or if the product has disassembled.
Always check food temperature before feeding. Always stir heated food to ensure even heat distribution and test the temperature before serving. When making up a feed, follow the formula milk manufacturers instruction. Never use feeding teats as a soother. Continuous and prolonged sucking of fluids will cause tooth decay.Tooth decay in young children can occur even when non-sweetened fluids are used. This can occur if the baby is allowed to use the bottle for long periods through the day and particularly through the night when saliva flow is reduced or if it is used as a soother.

CLEANING AND STERILISING

• Before first use clean the product.
• Always wash the product immediately after use.
• Clean before each use.
• Before first use place in boiling water for 5 minutes. This is to ensure hygiene.
• Wash in warm soapy water and rinse thoroughly with clean water or dishwasher (top rack only).
• For cleaning other bottle parts, use a closer to nature teat and spout brush.
• Once you have cleaned your bottles they are ready to sterilise.
• All bottle components should be sterilised.
• All bottle components are suitable for sterilisation by steam (electric or microwave) boiling or cold water tablet/liquid sterilisation.
• Do not clean wit harsh chemicals.
• Do not allow product to come into contact with oil based foods (e 9 oil/tomato based sauces) as staining will occur.
• Do not turn the teat inside out for cleaning. Damage could result.
• TAKE EXTRA CARE when cleaning the easl-vent valve. In order or ensure optimum venting the teat valve is manufactured using a thinner silicone than the teat itself and therefore care needs to be taken during cleaning to ensure no damage is caused.
• DO NOT USE TEAT BRUSH or any other implements to clean the easi-vent valve/the feeding hole as damage such as slits and tears may occur. However, performance of the teat may be affected if the easi-vent valve is not cleaned thoroughly after each use. Ensure valve is flushed with the warm water during cleaning.
• When assembling your bottle it is important that you can check that the slit in the silicone has not sealed closed. If it has been sealed closed, pinch it gently between your fingers to re-open. If the valve has sealed closed your bottle will not vent property.

STORAGE AND USE

• Inspect before each use and pull the feeding teat in all directions. Throw away at the first signs of damage or weakness.
• Keep all components not in use out of reach of children.
• For safety and hygiene reasons it is recommended that the feeding teat is replaces at least every 2 months.
• Do not store or leave in direct sunlight or near a source of heat or leave in disinfectant (sterilising solution) for longer than recommended, as this may weaken the teat.
• Do not store with or allow to come into contact with solvents or harsh chemicals.
• Not suitable for use in conventional oven or a combination microwave oven with the grill feature switched on

Materials listing:
TPE, PPSU, Polypropelene, silicone, tissue paper, wood pulp, super absorbent polymer, and polyethylene.
Tommee Tippee Closer to Nature bottles are only suitable for use with Tommee Tippee Closer to Nature teats.
Testing Standard:
GB 4806.7-2016 (ppsu bottle, screw ring , hood and milk storage pot)
GB 4806.2-2015 (Silicone Teat)
GB 4806.11-2016(Silicone Horn, valve )
GB 15979-2002 (Breast Pads)

Leaflet number:0300034
Copyright Jackel International Limited 2016
Jackel International Limited retains all intellectual property rights to this product and packaging, including all two and three dimensional designs, graphic images, logos and text. Any unauthorized manufacture, publication, reproduction, communication or adaption of any materials compromised in this product or its packaging is strictly prohibited and may constitute infringement of relevant laws.
Jackel International Limited is incorporated in England and Wales under company number 01894022
Tommee Tippee and Closer To Nature are registered trademarks of Jackel International Limited

digital video monitor
with movement sensor pad
INSTRUCTIONS FOR USE
model 1094S
tommeetippee.com

baby unit (=BU) 1094SB

parent unit (=PU) 1094SP

parent unit LEDs

charging your monitor before first use:

THE PARENT UNIT:

1. The parent unit is supplied with a rechargeable battery pack.
2. To insert the battery pack, open the battery casing with a screwdriver. Insert the supplied rechargeable battery pack. Take extra care to ensure that the battery pack is inserted correctly and the right way round. Refit the battery casing securely with a screwdriver.
3. DO NOT use a non-rechargeable battery pack. ONLY use battery pack supplied.
4. Plug the mains power cable into socket on side of parent unit and connect the other end of the mains power cable to the mains power.
5. Power on the parent unit and charge for 10 hours before use.

THE BABY UNIT:

1. The baby unit does not require batteries if powered from the mains.
2. If mains usage is not available, the baby unit will operate on batteries 4 x alkaline AA (LR6), which are not supplied.
3. To insert batteries, open the battery casing with a screwdriver. Insert 4 x alkaline AA (LR6) batteries (rechargeable or non-rechargeable, but not mixed) and close casing securely with screwdriver. Take extra care to ensure that the batteries are inserted correctly and the right way round.
4. There is NO charging function on the baby unit.
5. The battery light flashes orange to indicate the battery is low.
6. Battery power is disconnected automatically when the mains adaptor is in use. If the adaptor is turned off at the mains and still remains connected to the monitor then the batteries will be automatically activated.

CAUTION:
Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Use only rechargeable Li-polymer battery 950mAh with rating: 3.7/950mAh. Rechargeable battery: Manufacturer: BYD COMPANY LIMITED Model no.: SCD530-1 FOR REPLACEMENT PARENT UNIT BATTERIES, VISIT OUR WEBSITE www.tommeetippee.com

correct use of batteries

• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the baby unit before being charged.
• Rechargeable batteries are only to be charged under adult supervision.
• Different types of batteries or new and used batteries are not to be mixed.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the monitor.

CAUTION: risk of severe malfunction if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

setting up the parent unit

1. Connect the mains adaptor into a nearby wall socket in your baby’s nursery and switch on the power at the mains.
2. Press POWER on the parent unit until the POWER INDICATOR is on. The parent unit is now powered on and the parent unit will search for and link itself to the baby unit.
3. Ensure that the sensor pad on-off switch is turned OFF.
4. In monitoring mode, you can press <LCD ON/OFF> on the parent unit. Turning off the LCD will not power off the parent unit, you can still monitor the baby with it

NOTE:
Any triggering events such as baby cries, temperature of baby’s room exceeds the alert range, parent unit loses link with baby unit, etc. will turn on the LCD automatically.
setting up your baby unit

1. Connect the mains adaptor into a nearby wall socket in your baby’s nursery and switch on the power at the mains.
2. Press POWER on the baby unit until the POWER INDICATOR is on. The baby unit is now powered on and will link with the parent unit.
3. Ensure that the sensor pad on-off switch is turned OFF.
4. Direct the camera towards the baby’s cot. For adjusting the zoom feature, refer to section ‘Adjusting the Zoom’.

WARNING about using the baby unit!
• The baby unit should be 1 to 1.5 metres away from the baby’s cot on a flat surface or use the tripod mount.
• Never place the baby unit in or attach to the baby’s cot.

testing the parent unit

• First ensure that the baby unit has been set up and is working correctly following the previous instructions.
• To test the parent unit you must ensure that it is at least 5 metres away from the baby unit.
• Turn the sensor pad OFF.
• Place a sound source in the nursery at least 1 to 1.5 metres away from the baby unit, close the nursery door and go to another room with the parent unit only.
• Turn on the power and adjust the volume up or down to a comfortable level.
• You will hear sounds from your nursery.
• Walk around your house and garden with the parent unit, ensuring that you can hear the sounds from the baby unit at all times. The monitor will work up to a distance range of 300m approximately. Depending on the surrounding conditions as well as spatial and structural factors. The range indoors is normally less than outdoors.
• If you lose the signal from the baby unit a beep tone will be emitted from the parent unit and the antenna icon will flash. Even if the speaker volume is set OFF, the alert tone will still emit at volume level 1 when no link alert is triggered. Alert tone will only be emitted once initially. The screen will continue to show NO LINK until restored.

WARNING about the danger of cords:
STRANGULATION HAZARD! – Keep cords out of the reach of children. Do not use with an extension cord.WARNING! STRANGULATION HAZARD! Children have STRANGLED in cords. When using without protective covering. Keep this cord out of the reach of children (more than 0.9 m (3ft) away).

• Check immediately the location of corded monitors to make sure cords are out of arm’s reach of your baby and other young children.
• Place cords more than a metre away from any part of the cot. The monitor must not be used in any other sleep environment.
• Check the location of the monitor periodically, as what is within arm’s reach to a baby will change as the baby grows.
• Make sure the sensor cords are taut and not dangling to reduce the strangulation hazard.
• Do not place furniture or other obstructions on the adaptor cords and be sure to position them so that nobody can trip over them
• Keep adaptor cords away from hot surfaces such as radiators and central heating pipes.
• Be careful not to position the adaptor where a child might try to stop on it.
• Never use Tommee Tippee monitor adaptors with any other equipment. Nor should you use any other adaptors with your Tommee Tippee monitor.
• Please note that the adaptors become warm in use – this is quite normal and not a hazard.
• The adaptors convert your AC power to a safe low DC voltage.
• Use the power adaptor provided.
• The product is only suitable for use for cots and cotbeds that comply with EN716.

Adaptor:
Manufacturer: TEN PAO INTERNATIONAL LTD.
Model no.: EU: S006MV0600080 UK: S006MB0600080

setting up the movement sensor pad

The monitor has the ability to monitor your baby’s movements via the highly sophisticated movement sensor pad. It is designed for use in a cot with a flat, filrm base. It should not be used in a travel cot, swinging crib, moses basket, or with a hollow or foam-free mattress.

• Place the sensor pad between the cot mattress and the cot base, directly under the area where your baby will be sleeping.
• Ensure the sensor pad is positioned the correct way up and that the connecting cord is fed through the base of the cot out of accessibility range of your baby (50cm from the surface of mattress) and other young children.
• If the cot has a solid base it may be necessary to make a small hole through which the connecting cord can pass.
• Ensure the connecting cord plug is pushed fully into the socket underneath the baby unit.
• Do not hang cable over the top or through the bars of the cot.
• Place the cable down and onto the floor.

IMPORTANT !
TEST YOUR SENSOR PAD BEFORE PROCEEDING FURTHER:

1. Turn the Sensor Pad switch to ON. The Sensor Pad LED on the Baby Unit will light up if movement is detected.
2. The Sensor Pad LED will light up GREEN and flash to show the connection is good and continuous movement is detected from child.
3. Check the sensor pad is working by touching the cot mattress gently anywhere near where your baby will be sleeping.
4. If the Parent Unit is linked with the Baby Unit successfully, the Sensor Pad icon will appear on the Parent Unit. The Sensor Pad status LED will light up if movement is detected and there will be an audible ticksound . The volume of the tick can be adjusted.
5. If the Sensor Pad switch is ON without the Sensor Pad being connected securely, there will be an error tone from the Baby Unit and the Sensor Pad icon in the Parent Unit will flash. The text ‘PLEASE CONNECT THE SENSOR PAD’ will also appear on the Parent Unit.
6. Test the alarm by continuing to touch the mattress for a few moments and then step away from the cot and stop all movement near the sensor pad.
7. After approximately 20 seconds the alarm will sound on both the Parent Unit and Baby Unit and the RED alarm light will come on . The text ‘PLEASE CHECK THE BABY’ will also appear on the parent unit until the Sensor Pad is reset.
8. If movement is detected again after the alarm has activated the alarm will stop and the red alarm light will flash on the baby unit and the parent unit to let you know that the alarm has activated.
9. To reset the alarm, switch the Sensor Pad off and on again.
10. If the Sensor Pad is securely installed, but switched off on the Baby Unit the text ‘PLEASE TURN ON THE SENSOR PAD’ will be displayed on the Parent Unit standby screen.

No alarm after 20 seconds of NO movement-Make sure there is no movement or vibration around thesensor pad and test again. If no alarm again after 20 seconds,increase sensitivity setting and test again.
False alarm when there IS movement-Check the connections are secure and test again. If alarmtriggers again, decrease sensitivity setting and test again.

if the movement sensor alarm sounds:

• The tommee tippee closer to nature movement sensor pad is NOT a medical device and is NOT designed to prevent cases of Sudden Infant Death Syndrome (SIDS). This tommee tippee closer to nature monitor is intended to help you monitor your child and is NOT to be used as a substitute for adult supervision.
• The alarm going off may not be a sign of a problem with your baby. It may be a sign that the baby has moved away from the sensor pad area, or that batteries are running low if not mains power operated.

adjusting the tick tone:
The audible ticking sound gives reassurance that your sensor pad is correctly connected and the monitor is sensing movement. If you wish to switch off the ticking sound:

1. Press <MENU> to access main menu
2. Press ▲ UP or ▼DOWN to select tick tone.
3. Press <MENU> to enter the sub-menu.
4. Press ▲ UP or ▼ DOWN> to select from ON to OFF.
5. Press <MENU> to confirm.

adjusting the sensitivity of the sensor pad:

This monitor is compatible with standard cot mattresses. With thicker mattresses (ie spring interior) you may need to adjust the sensitivity switch on the baby unit from it’s preset medium level to the high level. With some very thin mattresses you may need to change a low sensitivity level.

WARNINGS ABOUT USING THE SENSOR PAD!

• A moving or swinging cord may be interpreted by the sensor pad as a baby’s movement. To avoid this, ensure that the cord is not positioned where it may be subject to movement.
• You should ensure there is no vibration in or near the nursery, so that the sensor pad is monitoring only your baby’s movements.
• The sensor pad does not carry any electricity and will not affect your baby even if the mattress is subject to bedwetting or vomiting.
• Never immerse the sensor pad in liquid. To clean, wipe with a dry, lint free cloth.
• Never place the connecting cord in contact with any moving objects, or near any heated surface.
• Always ensure wires and cables are out of reach from your baby and younger children. Never place connecting cords amongst your baby’s bedding, the child could be strangled.
• Ensure the sensor pad is used the correct way up.
• Do not immerse sensor mat in liquid and avoid contact with moisture.
  HELPFUL ADVICE ABOUT USING THE SENSOR PAD:
• If you remove your baby from the cot (e.g. for a feed) remember to turn off the sensor pad. to prevent the alarm from sounding. Remember to switch the alarm back on when you put the baby back into the cot.

adjusting speaker volume of parent unit and baby unit
There are 5 volume levels on baby unit from level 1 to level 5, and 6 volume levels on parent unit, including level 1 to level 5 and Volume Off. The volume level of parent unit will be shown on the status bar when you adjust the volume.
ADJUSTING VOLUME OF PARENT UNIT

Press ▲ UP to increase or ▼ DOWN to decrease the volume of the parent unit. Mute icon will be displayed if the volume is turned off on the parent unit.

adjusting volume of baby unit

Press ▲ UP to increase or ▼ DOWN to decrease the volume of the baby unit. An audible alert will emit when you reach the highest or lowest volume level.
Changing the volume setting on the baby unit affects the volume when you use the Talk Back feature.
adjusting the zoom
The zoom mode allows you to view your baby.
The ZOOM icon will be displayed in the status bar of the parent unit.

1. In monitoring mode, press <ZOOM> to enter zoom mode.
2. Press ▲ UP/ ▼ DOWN / LEFT / RIGHT to navigate the zoom area.
3. Press <ZOOM> again to zoom out and return to the normal monitoring mode.

using the nightlight

1. Press the nightlight key on the baby unit.
2. To adjust the brightness or turn it off, press the key again with the sequence L>M>H>Off
3. To turn on from the Parent Unit, select the nightlight main menu and select the brightness level.
4. The nightlight function is limited to level 1 if the Baby Unit is running on batteries.
5. The nightlight on the Baby Unit operates even if the Parent Unit is out of battery or turned off.
6. The nightlight settings and icons are synchronized when the Baby Unit and Parent Unit are connected.

helpful advice about using the nightlight
• You may find it useful to use a lower brightness if you wish your baby not to sleep in complete darkness and then adjust to a higher brightness for when baby needs attention during the night and you do not wish to turn on the main bedroom lights.
• If operating in battery mode the brightness will function on Low (L) only and will fade out after 5 minutes.

using talkback
Talkback allows you to communicate from the parent unit to the baby unit to comfort and reassure your baby.

1. In monitoring mode, press and hold <TALK> on the parent unit to speak to baby.
2. The audio from the baby unit will be muted and the parent will not be able to hear the baby until the button has been released. The mute icon will be displayed on parent unit status bar.

ADJUSTING THE TALKBACK VOLUME
The baby unit has 5 volume levels from Level 1 to Level 5
During TalkBack, press ▲ UP or ▼ DOWN on the baby unit to increase or decrease the volume respectively.
parent unit settings of menu options

parent unit menu options – continued

setting the language

1. Press <MENU> to access main menu.
2. Press ▲ UP or ▼ DOWN to select LANGUAGE.
3. Press <MENU> to enter the sub-menu.
4. Press ▲ UP or ▼ DOWN to select the desired language.
5. Press <MENU> to confirm.

setting the display

1. Press <MENU> to access main menu.
2. Press ▲ UP or ▼ DOWN to select DISPLAY.
3. Press <MENU> to enter the sub-menu to set the brightness level.
4. Press ▲ UP or ▼ DOWN to select from Level 1 to Level 5. You can preview the brightness when scrolling the menu list.
5. Press <MENU> to confirm.

NOTE:
The LCD backlight is always on when in AC power mode from the mains. If operating in battery mode, the LCD backlight will fade out after 20 seconds after last key press.

adjusting the sound sensitivity

You can change the level of sensitivity on your baby monitor to suit your baby. For example, if your baby is a particularly quiet sleeper, you can increase the sensitivity levels so that you are sure to hear if baby disturbs or becomes uncomfortable.
There are 5 different levels. The microphone will be voice activated by the noise baby makes. Level 5 is the most sensitive. The sound sensitivity settings of the baby unit can be changed only when parent unit is linked with the baby unit:

1. Press <MENU> to access main menu
2. Press ▲ UP or ▼ DOWN to select SENSITIVITY.
3. Press <MENU> to enter the sub-menu.
4. Press ▲ UP or ▼ DOWN to select from Level 1 to Level 5.
5. Press <MENU> to confirm.

NOTE:
•If LCD is off, and baby voice reaches the sensitivity level 3,4 or 5, the LCD will be turned on automatically.
• When the microphone sensitivity of the baby unit is set to a high level, it picks up more sounds and therefore transmits more often. As a result, the units will consume more power.

setting the temperature format
The Baby Unit constantly monitors the temperature in your baby’s room and alerts you if it gets too hot or too cold. The temperature is displayed

1. Press <MENU> to access main menu
2. Press ▲ UP or ▼ DOWN to select TEMPERATURE.
3. Press <MENU> to select Format.
4. Press <MENU> to enter the sub-menu.
5. Press ▲ UP or ▼ DOWN to select Celsius or Fahrenheit.
6. Press <MENU> to confirm.
7. The real-time temperature format displayed on the status bar of parent unit will be changed accordingly.

NOTE:
The temperature displayed is for reference only. There may be a slight tolerance of the degree accuracy comparing with the actual temperature. It is important to physically check the actual temperature in your baby’s room regularly.

setting the vibration

1. Press <MENU> to access main menu
2. Press ▲ UP or ▼ DOWN to select VIBRATION.
3. Press <MENU> to enter the sub-menu.
4. Press ▲ UP or ▼ DOWN to turn the vibration ON or OFF.
5. Press <MENU> to confirm.
6. If ON, the Parent Unit will vibrate once to confirm it is activated.

NOTE:
•In vibration mode, the parent unit will vibrate when the noise level from the baby reaches sensitivity level 3, 4 or 5 while the loudspeaker volume of the parent unit is switched off.
• If the Parent Unit speaker volume is turned off whilst in monitoring mode and vibration mode, the Parent Unit will vibrate once.
• When the noise level from the baby reaches sensitivity level 3, 4 or 5, the vibrating alert is triggered and will vibrate every 5 seconds.

paging to locate the parent unit

1. If both ▲ UP (9a) and ▼ DOWN (9b) keys are pressed for 3 seconds on the baby unit at the same time, the paging tone is emitted.
2. PAGING will be displayed on the LCD of the parent unit.
3. If volume is OFF before paging starts, reset it to default volume level (4).
4. During paging, any key pressed on the parent unit will stop the paging tone.
5. If the link is lost between the parent unit and the baby unit, the paging tone will not be emitted when both ▲ UP (9a) and ▼ DOWN (9b) keys are pressed together. There will be no change on baby unit.
6. If paging is not stopped, it will expire in 2 minutes.
7. Paging function does not work if parent unit is turned off.

resetting to default settings
parent unit default

1. Ensure the parent unit is powered OFF.
2. Press and hold ▲ UP.
3. Press POWER.
4. The parent unit LCD will display ‘please press M to restore default settings’.
5. Press M to confirm.

baby unit default

1. Ensure the parent unit is powered OFF.
2. Press and hold ▲ UP.
3. Press POWER ON, whilst still holding ▲ UP.
4. After 3 seconds, the sensor pad alarm LED will flash.
5. Release ▲ UP key and press ▼ DOWN key. The sensor pad LED will resume on.

TROUBLESHOOTING

The link light on the parent unit does not come on
• Check whether the parent unit is powered on.
• Check whether the supplied rechargeable battery pack is correctly installed and not drained.

The link light on the parent unit flashes
• The parent unit and the baby unit may be out of range with each other. Reduce the distance between the units, but not closer than 1.5 metres.
• The baby unit may be switched off. Press <POWER> key to switch on the baby unit.

The low battery indicator on the baby unit flashes
• Replace with 4 x alkaline AA (LR6) batteries or connect the baby unit to the mains power.

The low battery icon on the parent unit LCD screen flashes
• The rechargeable battery pack in the parent unit is running low. Connect the parent unit to the mains power with the supplied power adaptor for recharging.

The parent unit beeps
• This means the connection has been lost with the baby unit. Reduce the distance between the parent unit and the baby unit, but not closer than 1.5 metres.
• The baby unit may be switched off. Switch on the baby unit.
• The rechargeable battery pack in the parent unit is running low. Connect the parent unit to the mains power with the supplied power adaptor for recharging.
• The temperature alert may have triggered. Check the temperature of the baby’s room.
Cannot view the video image of baby from the parent unit.
• The LCD may be turned off. Switch on the LCD.
• The parent unit and the baby unit may be out of range with each other. Reduce the distance between the units, but not closer than 1.5 metres.
• The rechargeable battery pack in the parent unit is drained. Connect the parent unit to the mains power with the supplied power adaptor for recharging.
Cannot hear sound or baby cry from the parent unit.
• The volume level in the parent unit may be set too low. Increase the volume level of the parent unit.
• The microphone sensitivity level of the baby unit may be set too low. Increase the sensitivity level of the baby unit.
• The parent unit and the baby unit may be out of range with each other. Reduce the distance between the units, but not closer than 1.5 metres.
The parent unit is too sensitive to room sounds.
• The microphone sensitivity level of the baby unit may be set too high. Decrease the microphone sensitivity level of the baby unit from the parent unit.
The baby monitor system produces a high-pitched noise.
• The parent unit and the baby unit are too close to each other. Make sure the parent unit and baby unit are at least 1.5 meters away from each other.
• The speaker volume of the parent unit maybe set too high. Decrease the volume of the parent unit.
How long does the nightlight last?
• If the baby unit is run on batteries the nightlight will fade out after 5 minutes. If is run from the mains
electricity it will remain on until switched off.
Alkaline batteries in the baby unit are running low quickly.
• The microphone sensitivity level of the baby unit may be set too high. Decrease the microphone sensitivity level of the baby unit from the parent unit.
• The volume level of the baby unit may be set too high which consumes power. Decrease the volume level of the baby unit.
The rechargeable battery pack in the parent unit is running low quickly.
• The volume level of the parent unit may be set too high. Decrease the volume level of the parent unit.
• For a replacement battery, visit our website www.tommeetippee.com
Talkback feature is not working.
• Make sure the baby unit is powered on and the link between parent and baby unit is normal.

GENERAL SAFETY INFORMATION:

• Warning! Adult use only – Keep out of reach of children at all times. Do not allow a child to play with it – It is not a Toy
• Make sure you store your monitor in a safe place when not in use, away from heat and water.
• Take care not to drop either unit as this may affect the functioning of you monitor.
IMPORTANT:
The Tommee Tippee monitor has been designed to give you added reassurance for those times when you cannot be in the same room as your baby, it is NOT a substitute for proper adult supervision. It is important that an adult stays within range of the monitor at all times during use. Please remember that your Tommee Tippee monitor is not a medical device, nor a device to prevent cases of Sudden Infant Death Syndrome or ‘cot death’, and you should not rely on it for your baby’s well-being. You should personally check your baby as frequently as necessary.

technical specifcations

IMPORTANT SAFETY INSTRUCTIONS:
• When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following:
1. Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
2. Use only the power cord and batteries indicated in this manual. Do not dispose of batteries in a fire, they may explode. Check with local regulations for possible special disposal instructions.

If you are having any problems in setting up your monitor or require any further information please visit our website www.tommeetippee.com Please retain our address for future reference:
Mayborn Baby and Child
Northumberland Business Park West
Cramlington
Northumberland
NE23 7RH, UK
441010

DECLARATION OF CONFORMITY

We, Jackel International Ltd trading as Mayborn Baby and Child Dudley Lane, Cramlington, Northumberland, NE23 7RH, UK
declare under our responsibility that the electrical product:
Tommee Tippee Model 1094S
Closer to Nature Digital Video Baby Monitor
Closer to Nature Digital Video Baby Monitor with Movement Sensor Pad
which this declaration relates to is in conformity with the following standards:
RF: EN 300 328
RF: EN 50371
EMC: EN 301489-1/-17
LVD: EN 60950-1
LED: EN 60825
Following the provisions of 1999/5/EC (R&TTE Directive) the product is produced by a manufacturing organisation accredited to ISO 9001
Andrew Richardson – Quality Assurance Manager

Cramlington, December 2011

Tommee Tippee Perfect Prep Machine User Manual

perfect prep™ machine
INSTRUCTIONS FOR USE
(these instructions and cleaning videos can be found at tommeetippee.com)

IMPORTANT WARNINGS!
Keep this instruction sheet for future reference as it includes important information.
This appliance is intended for household use only. Do not use the outdoors. Before plugging in the Perfect Prep for the first time ensure that the voltage is compatible with your electricity supply by checking the label on the base of the unit. Ensure water has been added to the unit before switching the unit on. Do not immerse in water. To protect against fire, electric shock, and injury to persons. Do not immerse the cord,  plugs, or other parts of the unit in water or other liquid. Misuse of the product may result in the risk of fire, electric shock, and/or personal injury. This appliance shall not be used by children. Keep the appliance and its cord out of reach of children. Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. User maintenance other than cleaning and descaling is not required for this product. Cleaning and user maintenance shall not be made by children.

Do not touch hot surfaces. When in use the Perfect Prep contains hot water and steam. Keep hands away from dispensing spout as it can cause burns and scalds. Use in a well-ventilated area. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. If the supply cord is damaged it must be changed by a qualified person in order to avoid a hazard. If the damage is from new the unit must be returned to the manufacturer. If within a retail warranty period this product should be exchanged at place of purchase. The manufacturer will then be made aware. Any questions? Visit our website www.tommeetippee.com.

Always use on a flat heat-resistant surface. Do not move appliance when in use. Do not let the cord hang over edge of kitchen work surface or touch hot surfaces. The product has been fitted with a cord wind on the rear of the unit to allow you to adjust the length of the cord safely.  It is recommended that the cord be kept as short as possible. Do not use any accessories other than those supplied with this appliance.

SET UP

As with any other method of making up a feed, it’s essential that good hygiene practices are observed in the use and maintenance of your  Perfect Prep Machine. Ensure your hands and all surfaces that come into contact with the machine and its components are clean, and that the unit is away from direct sunlight and heat sources.
REGULAR CLEANING: For hygiene and safety reasons you should clean your unit on a regular basis. We recommend you carry this out at least every 4 weeks, whenever you replace your filter or if the machine has been unused for a period of 7 days.

Before each use, you must ensure that your water tank is above the minimum fill mark.
Always use cold water when filling the water tank, other than when cleaning.

HOW TO KEEP THE TANK COOL
The Perfect Prep should be kept in a cool dry location, avoiding direct sunlight and keeping away from warm appliances. This is recommended to avoid the water tank temperature getting too warm.
Don’t worry if your temperature light does illuminate, as we have some tips for you:

1 Flush your cold tap for 10 seconds before filling the water tank.
2 Regularly top up with cold water rather than letting a full tank stand and warm for long periods of time.
3 Keep a cold jug of tap water in the fridge ready to top up the tank.

HOW TO STOP THE PERFECT PREP™ MACHINE

If at any point you need to stop the Perfect Prep machine you can do so by pressing the start/stop button. The pump may continue to run for a few seconds and the green light will illuminate to show that the process has ended.
It will not be possible to restart the machine for 20 seconds. If you have to stop the Perfect Prep machine, please discard of any incomplete feed.

CLEANING

We recommend you complete a cleaning cycle every 4 weeks, whenever you replace your Tommee Tippee water filter or if the machine has been unused for a period of 7 days.
TIP: carry out the cleaning process when your tank empty light is illuminated (L) so there’s no need to discard any water.

Remove lid, hopper (G) and bottle stand (F) and set filter to one side (top side down). Clean the external machine surface with a clean  cloth (we advise to use an antibacterial solution), taking care to clean in all grooves and under the dispenser spout (C). At this time the hopper  (G), lid and bottle stand (F) should also be cleaned using hot soapy water, rinsed thoroughly, and allowed to dry naturally (do not use cloths or tea towels to dry).

Using a cold water sterilising solution (following manufacturer guidelines for using 1.8 litres of water) add required amount to the water tank. Fill the water tank to the max line with cold water and place a suitable container under the dispenser spout (C).

TIP: If using a container less than 1.8 litres capacity you can press the start button (A) to pause the cleaning cycle, allowing you to discard of the contents.

Once this is done, insert the hopper and follow SET UP steps 1-15 (no need to use step 9a or 12 if re-fitting currentTommee Tippee filter).

REPLACING YOUR FILTER

We recommend that you complete a cleaning cycle, whenever you replace your Tommee Tippee water filter. Your unit comes with a Tommee  Tippee water filter which lasts 150 liters (this is approximately 3 months based on 6 x 260ml feeds per day). Replacement Tommee Tippee water filters are available from all Perfect Prep stockists. Using this machine without a water filter or with a non Tommee Tippee water filter could put your child’s health at risk.

DESCALING

The descaling process will remove deposits of calcium and other minerals in the system that may affect its performance.

A red warning light will illuminate when the unit requires descaling soon.
If the light flashes, you should descale immediately

1. Remove the filter.
2. Fill the water tank with 0.5 litres of clear white vinegar (food grade).
3. Place a suitable container under the spout.
4. Press the descale button for 2 seconds. The system will now run a descale process.
   During this process, the red descale light will continue to flash.
5. At the end of the descaling process, a beep will sound and the descale light will switch off.
6. The red cleaning mode light will now flash.
7. Follow the SETUP steps 1-15 (no need to use step 9a or 12 if refitting current filter)

DO’S AND DON’TS

DOS
It is essential that good hygiene practices are observed in the use and maintenance of your Perfect Prep machine.

• Ensure your hands and all surfaces that come in to contact with the machine and its components (including filter) are clean.
• This product is intended for use with Tommee Tippee Closer to Nature Perfect Prep Water Filters which are available
  from all Perfect Prep machine stockists.

USE OF ANY OTHER WATER FILTER WITH THIS PRODUCT COULD PUT YOUR CHILD’S HEALTH AT RISK.

• Before first use clean the unit following the set up steps provided in this leaflet.
• Keep the unit away from direct sunlight.
• Only use cold tap water during regular use.
• Keep the outside of the unit clean.
• For your childs safety always check the food temperature before feeding on a sensitive part of your skin.
• Be careful when handling boiling water.
• Always adjust the height of the bottle stand so the bottle neck is close to the dispensing spout. This is to maintain thetemperature of the water and to avoid any splashes.
• Keep well clear of the dispensing spout as the unit produces steam and very hot water.

DON’TS

• Do not allow the water tank to be contaminated. The inside of the unit should only be cleaned by following the cleaning process steps provided in this leaflet.
• Do not clean with solvents or harsh chemicals.
• The appliance is intended for use in a kitchen. It is not suitable for use in a nursery.
• Do not use hot water other than during cleaning cycles. If water in the tank is higher than 25°C, the unit will not operate.
• If this happens, either change the water or allow the water to cool and restart.
• Do not pour boiling water over the water filter.
• When topping up the hopper, do not fill beyond the max line.
• Be careful not to spill any water on the outside of the machine.
• Do not remove the back panel from the unit.

INFORMATION ON THE DISPOSAL FOR WASTE ELECTRICAL & ELECTRONIC EQUIPMENT (WEEE)This symbol on the products and accompanying documents means that used electrical and electronic products should not be mixed with general household waste.

For proper disposal for treatment, recovery, and recycling, please take these products to designated collection points where they will be accepted on a free of charge basis. In some countries, you may be able to return your products to your local retailer upon the purchase of a  new product. Disposing of this product correctly will help you save valuable resources and prevent any possible effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest collection point for WEEE. Penalties may be applicable for the incorrect disposal of this product in accordance with national legislation.
The product is fitted with a BS 1363 mains plug containing a 13A fuse. If it ever becomes necessary to replace the fuse, only use fuses that are marked BS 1362, and rated at 13A. In the unlikely event that this plug is not suitable for the sockets in your home, it should be removed  and a suitable plug fitted as follows: The wires of the mains lead are colored in accordance with the following code:

• GREEN AND YELLOW – EARTH
• BLUE – NEUTRAL
• BROWN – LIVE

As these colours may not correspond with the coloured markings sometimes used to identify the terminals in the plug, connect as follows. The wire coloured GREEN AND YELLOW must be connected to the terminal marked E or by the earth symbol or coloured GREEN or  GREEN AND YELLOW. The wire-coloured BLUE must be connected to the terminal marked N or coloured BLACK. The wire-coloured BROWN must be connected to the terminal marked L or coloured RED. If you are in any doubt about how to wire a plug or replace a fuse safely, consult a qualified electrician.
Jackel International Limited trading as Mayborn Group, Northumberland Business Park West, Cramlington Northumberland NE23 7RH, UK
Made in China

FAQS

Do you leave the filter in the hopper when running the bi-weekly cleaning cycle if filter is not being changed?

Yes. There is a little light the comes on that tells you when the filter needs to be changed. It’s usually around 3 months, depending on the size of bottles you’re using and how often you use it

why does this item swap from 60 to 79.99 at checkout??

The price depends on cokour and sometimes the tax isn’t included untill checkout

Can we choose a machine that indicates ml ? and not oz?

No it only comes in ml.

Does the perfect prep machine run off of 12v?

It has a plug and runs of mains electricity.

What is the Watts on this?

It doesn’t tell you the whattage.

The water light on the side of the machine isn’t working. Why is this?

Probably the water is too hot

does this comes with a european plug?

To be honest unsure as bought as a gift but being a UK purchase wouldn’t imagine so.

How do u empty the water out of the hopper?

You need to pick up the whole machine and pour it out. There’s no easier way or alternate way to do it.

What does calc light mean?

It means that the unit needs to be descaled. You do it with water and white vinegar. The instructions are included.

Which temperature?

It initially puts boiling water in, then adds cool to produce a bottle at a ready to drink temperature.

The initial hot shot is boiling water? Or just hot? cause sterilization requires boiling water right? I’d love to buy but need to be sure it’s safe

boiling

Does this one with a filter?

Yes, it comes with a filter in the box that you fit during setup. In requires replacement after around 3 months and the machine has an indicator that lights up when the filter needs to be replaced.

Is there any warranty ?

Yes there is

Do you have to use cooled boiled water to fill the machine or water straight from the tap?

Water straight from the tap, there’s an in built water filter & the machine instantly boils the correct amount of water which it then adds cold water to reach the perfect temperature. It’s so easy.

Does this sterilise the bottle as well?

No you still need to sterilise your bottles as per normal. The hot shot is enough to sterilise the formula but not the actual bottle itself.

What is the temperature of the “hot shot” of water (if anyone could possibly check would be greatly appreciated)?

It’s boiling water so the powder is sterilised.

Tommee Tippee First Sips

Product information for:

first sips transition cup
first straw transition cup
trainer sippee cup
trainer straw cup
mealtime trainer
sippee cup
sportee bottle
insulated sipper tumbler
insulated straw tumbler
sipper cup

SAFETY GUIDANCE

For your child’s safety and health.

WARNING!

• Always use this product with adult supervision. Accidents have occurred when babies have been left alone with drinking equipment due to the baby falling or if the product has disassembled.
• Never use spouts or straws as a pacifier. Continuous and prolonged sucking of fluids will cause tooth decay. Tooth decay in young children can occur even when non-sweetened fluids are used. This can occur if the baby is allowed to use the cup for long periods through the day and particularly through the night, when saliva flow is reduced or if it is used as a pacifier.
• Always check food temperature before feeding.
• Always stir heated food to ensure even heat distribution and test the temperature before serving
• Not suitable for microwave use apart from sterilizing. See cleaning and sterilization instructions below.

CLEANING AND STERILIZATION

• Before first use, clean the product.
• Clean before each use.
• Always wash the product immediately after use.
• Wash in warm soapy water and rinse in clean water or use a dishwasher (top shelf only). Do not clean with solvents or harsh chemicals.
• Do not allow product to come into contact with oil based foods (e.g. oil/tomato based sauces) as staining will occur.
• Our insulated sipper tumbler and insulated straw tumbler are suitable for sterilization by cold water tablet/liquid solution only.
• All other cups are suitable for sterilization by steam (electric and microwave), boiling or cold water tablet/liquid solution.

STORAGE AND USE

• Inspect before each use and pull the spout or straw in all directions. Throw away at the first signs of damage or weakness.
• Do not store or leave in direct sunlight or near a source of heat.
• Do not store with or allow to come into contact with solvents or harsh chemicals.
• Keep all components not in use out of reach of children
• Not suitable for use in a convectional oven or a combination microwave oven with the grill feature switched on.
• As with most sippy cups, ours are to be used with milk, water or juices that don’t contain pulp.
• DO NOT use with carbonated beverages, formula or hot liquids.

INSTRUCTIONS FOR CLEANING STRAW CUPS

1. Unscrew the lid.
2. Pop up the straw by pressing the trigger. (Fig. 1)
3. Wash in warm soapy water and rinse in clean water or use a dishwasher (top shelf only).
4. If the straw has been completely removed from the lid – remove the trigger from the lid by pushing to the left then right. Push the straw through the lid, and then pull the straw from the top, until the valve seals in position. Squeeze the valve to ensure it is open. (Fig 2.)
5. Replace lid on base.

INSTRUCTIONS FOR CLEANING VALVE CUPS

1. Unscrew the lid. Pull the valve out (this is important for a thorough cleaning of the valve). You may need to wiggle the valve left to right to get it to release. (Fig. 3)
2. After each use, immediately wash all parts thoroughly in warm soapy water and rinse in clean water. The valve should be hand-washed only. All other parts including the lid, base, cover and handles can be washed in the dishwasher (top shelf only).
3. To ensure no residual soapy water is left in the valve, run clean water directly into all four openings after washing.
4. To remove excess water, shake the valve and let it air-dry before reassembling it with the cup. Store your lids and cups separately, to allow air to circulate freely.
5. Once all parts are dry, to re-assemble, place the valve back in the lid, pushing until the four sides lock into place. (Fig.4) Screw the lid back on the cup.

INSTRUCTIONS FOR USE

When replacing the lid onto the bottle base align the two dots on the back of the cup. (Fig 5). This ensures the optimum fit. DO NOT OVERTIGHTEN. This cup is designed as a meal time trainer and may leak if over tightened and not stored upright when full.

INSTRUCTION FOR CLEANING MEALTIME TRAINER

1. Un-screw the lid unit from the cup base.
2. Take the lid unit apart by gripping the lid top and turning the locking connector anti-clockwise. (Fig. 6) Separate the locking connector, silicone disk, screw ring and lid top.
3. Wash all parts in warm soapy water and rinse in clean water or use a dishwasher (top shelf only).
4. Re-assemble by turning the screw ring upside down and placing the silicone disk inside with the grooves facing up. (Fig. 7)
5. Take the lid top and push up through the hole in the silicone disk (Fig. 8 A)
6. Align locking connector and twist to lock. (Fig. 8 B)
7. Place the lid on the base. REMEMBER to align the two dots on the back. (Fig 5) DO NOT OVER TIGHTEN.
8. The cup has been assembled correctly when the lid top aligns with screw ring and can be pressed down on. (Fig. 9) If the lid top can not be pushed down, the silicone disk has been assembled up-side down.

THE TOMMEE TIPPEE CUP RANGE

Distributed By Mayborn USA;
Mayborn USA Inc. dba Mayborn Group
1 Edgewater Drive
Suite 109
Norwood, MA 02062

Copyright © Mayborn USA. 2014.
TOMMEE TIPPEE is a registered trademark.

Any manufacture, publication, copying, hiring, lending and reproduction of any materials is strictly prohibited and constitutes infringement.

Patents Pending.

Tommee Tippee 1063 Electric Breast Pump Instructions Manual

Closer to nature® electric breast pump

For hygiene reasons this product cannot be returned once opened unless faulty.
Please read and retain this information for future reference.
The intended use of the Tommee Tippee Electric Breast Pump is to express milk from the breast of lactating women. Researched and developed by specialists and breastfeeding experts to express milk for storage and later use.

PARTS GUIDE

1. Silicone insert
2. Horn
3. Upper pump body
4. Lower pump body
5. Release tabs
6. Diaphragm
7. Diaphragm cap
8. Valve
9. Airtube
10. Air tube socket
11. Mains adaptor socket
12. Motor
13. On/off button
14. Low expression button/light indicator
15. Medium expression button/light indicator
16. High expression button/light indicator
17. 150ml bottle
18. Bottle stand & horn hygiene cover
19. 60ml milk storage pot
20. Breast pads
21. Mains adaptor
22. Steriliser box

DISASSEMBLING THE ELECTRIC BREAST PUMP

1. Unscrew bottle from lower pump body.
2. Pull off valve.
3. Pull air tube from upper pump body and motor unit.
4. Press release tabs to release upper pump body and pull apart.
5. Pull out diaphragm cap and diaphragm.
6. Pull horn from lower pump body.

IT IS NOT ESSENTIAL TO TAKE THE SILICONE INSERT OUT OF THE HORN FOR CLEANING unless milk or dirt has become trapped inside. If so, unclip lip from cup and pull apart.

CLEANING, STERILISING AND MAINTENANCE

Before use ensure the breast pump has been disassembled, washed and sterilised.
The parts to be sterilised are :

Silicone insert, horn, upper pump body, lower pump body, diaphragm, diaphragm cap, valve, bottle, horn hygiene cover, and milk storage lid or milk storage pods if required. These components are suitable for sterilization by steam {electric and microwave), boiling or cold water tablelliquid solution. Follow the sterilizer manufacturer’s instructions
Do not sterilise:

Air tube, motor unit and adaptor. Wipe clean only with a damp cloth.

• Always wash the product  mmediately after use to remove milk residue.
• Wash all products to be sterilised in warm soapy water and rinse in clean water or use a dishwasher.
• Do not clean with solvents or harsh chemicals.
• Do not allow product to come into contact with oil based foods (e.g. oil/ tomato based sauces) as staining will occur.
• Inspect the air tube before and after each use for condensation. Allow to air dry before next use.
• To clean the valve, rub gently between your fingers in warm soapy water-do not insert objects as damage could result.
• Routine maintenance includes cleaning. No other servicing is required.

ASSEMBLING THE ELECTRIC BREAST PUMP

1. Wash your hands thoroughly before handling the pump.
   Wash and sterilise your breast pump before using. Follow instructions in section for CLEANING, STERILISING AND MAINTENANCE.
2. Make sure the silicone insert is securely attached. Clip lip over end of horn first, then push tube through funnel, ensuring lip is fully clipped over the other side also.
3. Push horn onto the lower pump body as far as it will go.
4. Push diaphragm down into lower pump body as far as it will go and push diaphragm cap over the top as far as it will go until it is sealed.
5. Push upper pump body and lower pump body together. They will click into place.
6. Push valve onto lower pump body.
7. Screw bottle onto lower pump body .
8. Connect air tube onto upper pump body and the air tube socket of the motor unit. This is on the RIGHT of the two sockets on the motor unit.
9. Plug the electric adaptor into the electric adaptor socket of the motor unit. This is on the LEFT.
10. Plug the electric adaptor into the mains power supply.

BATTERY OPERATION

1. To install batteries, disconnect the air tube and mains adaptor.
2. Push the clip of the battery compartment towards centre of motor unit whilst pulling upwards. Remove the cover.
3. Insert batteries as indicated inside the battery compartment and push the cover back into place until it snaps shut.
4. Batteries are to be inserted with the correct polarity. Ensure that the+ and -ends of the batteries are positioned correctly.

Requires 4AA batteries (sold separately). DO NOT USE RECHARGEABLE BATTERIES. The use of rechargeable batteries could cause your breast pump to
malfunction and will void the warranty. Non-rechargeable batteries are not to be recharged. Different types of batteries are not to be mixed. Only batteries of the same or equivalent type as recommended are to be used. Exhausted batteries are to be removed from the breast pump. Batteries should always be removed or replaced by an adult. Keep away from children. Remove batteries if the electric breast pump will not be used for some time. Help the environment by disposing of your product responsibly. Please use designated collection points or recycling facilities when disposing of the item or batteries.

USING THE ELECTRIC BREAST PUMP

1. Ensure that the breast pump has been cleaned and sterilised. Wash your hands before touching the breast pump or your breasts and avoid touching inside the breast pump or the storage pot. Find a comfortable chair where you can relax
2. Hold the pump in whichever hand is most comfortable.
3. Place the silicone insert of the horn over your breast, so that it creates a seal all the way round. IF AIR CAN GET IN THERE WILL BE LOW OR NO SUCTION,
4. Press the on/off button to promote milk let-down. This let-down setting is a gentle rhythm to get your milk flowing.
5. IMPORTANT: Sit upright and do not tilt the bottle while pumping, it should be kept upright at all times to avoid milk flowing back up through the air tube. If this happens you must turn the breast pump off immediately as it could damage the motor. Read HELPFUL ADVICE for further information.
6. After approximately a minute or so, your breast milk will start flowing freely. At this point, we recommend you press the low expression button.
7. To increase the expression level, press the medium expression button ••. The button will light up. If expressing is uncomfortable at this level switch back to the slower level by pressing the low expression button.
8. If you would like to express faster than the medium expression level, press the high expression button •••. The button will light up. If expressing is uncomfortable at this level switch back to medium expression.
9. Adjust expression level accordingly to achieve maximum comfort.
10. Avoid overfilling bottle. Switch off if you express over 150ml.
11. Once finished pumping, switch off the breast pump and unplug it. You do not need to sterilise your pump until you are ready to use it again.
12. Cover and store the expressed milk for later use.

THE CLOSER TO NATURE• ELECTRIC BREAST PUMP CAN ONLY BE USED WITH TOMMEE TIPPEE• CLOSER TO NATURE’ BOTTLES.
A SEPARATE INSTRUCTION SHEET ON HOW TO CLEAN AND STERILISE THETOMMEETIPPEE• CLOSER TO NATURE• BOTTLE IS ENCLOSED. PLEASE READ AND RETAIN THIS IMPORTANT INFORMATION FOR FUTURE REFERENCE.

1. On/off Button to promote milk let down
2.   Low expression button
3.  Medium expression button
4. High expression button

IMPORTANT WARNINGS!

• Keep this instruction sheet for future reference as it includes important information.
• This appliance is intended for household use only. Do not use outdoors.
• Before plugging in the breast pump for the first time ensure that the voltage is compatible with your electricity supply adaptors by checking the label on the base of the unit and the supplied adaptors.
• Do not immerse. To protect against fire, electric shock and injury to persons. Do not immerse cord, plugs, motor unit and air tube in water or other liquid or clean with a wet sponge or cloth.
• Keep the appliance and its cord out of reach of children. Children shall be supervised to ensure that they do not play with this appliance. Do not place furniture or other obstructions on the adapter cables and be sure to position them so that nobody can trip over them. Always position the adaptor and cord well out of reach of your baby and any young children. Be careful not to position them where a child might try to step on it. Keep adaptor cords away from hot surfaces such as radiators or central heating pipes.
• User maintenance other than cleaning and sterilization is not required for this product.
• Always unplug from the power supply when not in use.
• Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. If the supply cord is damaged it must be changed by a qualified person in order to avoid a hazard. If the damage is from new the unit must be returned to the manufacturer. If within a retail warranty period this product should be exchanged at place of purchase.
• Do not use any accessories other than those supplied with this appliance. The use of accessories, transducers and cables other than those specified with the exception of transducers and cables sold by the manufacturer of the MODEL 1063 as replacement parts for internal components may result in increased EMMISSIONS or decreased IMMUNITY of the MODEL 1063. MODEL 1063 should not be used adjacent to or stacked with other equipment.
• The adaptor converts your AC power so that it is only supplied at safety extra low voltage corresponding to the marking on the appliance. The Electric Breast Pump MODEL 1063 is only to be used with adapter model number SJB0500800PC
• Adapter rating – Input: 0.3A Output 5.0 VDC 800 mA
• Motor unit rating – 4.8-5.0VDC 800mA
• BATTERY WARNINGS – Batteries are to be inserted with the correct polarity. Ensure that the+ and – ends of the batteries are positioned correctly. Requires 4 AA batteries (sold separately). DO NOT USE RECHARGABLE BATTERIES. The use of rechargeable batteries could cause your breast pump to malfunction and will void the warranty. Non rechargeable batteries are not to be recharged. Different types of batteries or new and used batteries are not to be mixed. Only batteries of the same or equivalent type as recommended are to be used. Exhausted batteries are to be removed from the breast pump. Batteries should always be removed or replaced by an adult. Keep batteries away from children. Remove batteries if the electric breast pump will not be used for some time.

HELPFUL ADVICE

• The best time to use your breast pump is after the first feed of the day (unless otherwise advised by your breastfeeding advisor)
• Be comfortable and relax, e.g. watch the TV or have your favorite music playing.
• Remember you are only trying to express milk from just behind the nipple- strong suction is not necessary.
• There should be no pain using your breast pump. If you feel pain, try using the pump more gently. Then examine your breasts. If there are any red or hot areas contact your breastfeeding advisor as soon as possible.
• Do not continue to use the pump once your milk has stopped flowing.
• Wash all breastfeeding equipment after use and before sterilisation.

IF THERE IS LO W OR NO SUCTION:
Make sure all connections are secure. Make sure the silicone insert on the horn forms a complete seal around the breast. Make sure the valve is cleaned and not damaged. Make sure the air tube is securely fitted to the upper pump body and the motor unit. Check there is no kink in the air tube.
IF PUMP WILL NOT TURN ON:

Make sure the pump is plugged in correctly. Make sure the “on” button is pressed and the light is on. Do not repeatedly press the on ‘off button. If using batteries, make sure the mains adaptor is not plugged into the pump. If using batteries, make sure batteries are installed correctly.
STERILISER BOX
To use:

1. 1. Pour 100ml of water into sterilising box
2. Load upturned bottle, disassembled breast pump and any accessories.
3. Securely fit box lid.
4. Open valve, on lid of box.
5. Place steriliser box in microwave.
6. Follow instructions according to microwave output.
7. CAUTION: To avoid risk of burning, always ensure box is cool to touch before lifting out.
8. Immediately fit valve on lid to make box airtight and sterile.

USING THE BREAST MILK STORAGE SYSTEM

For use with the Tommee Tippee closer to nature breast pumps
HOW TOUSE

1. Ensure pot is clean and sterilised.
2. Place pot inside of bottle.
3. Screw bottle onto bottle neck adaptor and continue to follow assembly of breast pump instructions.
4. When the breast pump is fully assembled and in usage, the pot will hold up to 60ml 12oz.
5. Once you have expressed 60ml stop pumping, place lid on storage pot and remove from bottle.
6. Store pot in either the fridge or freezer. See storage guide below.
7. If you want to continue expressing, either insert another clean and sterilised pot or express directly into the bottle of the breast pump

STORAGE OF BREAST MILK

1. You will notice that stored milk separates out into layers. Shake to remix thoroughly before feeding.
2. When freezing milk, allow space at the top of the bottle for expansion. It is easiest to freeze milk in individual feed quantities of 60-125ml (2-4oz).
3. Thaw frozen milk in the fridge or by standing the bottle in luke warm water until it has reached body temperature.
4. If you want to take expressed milk with you when you are out, make sure it stays cold or frozen until needed.

USING BREAST MILK STORAGE SYSTEM AS A SIPPY CUP

1. If milk has been chilled, remove lid and place in warm water to heat to temperature required. Always check food temperature before feeding.
2. Hold cup up to baby’s mouth and gently tip to allow baby to sip from cup.

For your child’s safety and health

WARNING!
Always use this product with adult supervision. Accidents have occurred when babies have been left alone with drinking equipment due to the baby falling or if the product has disassembled.
Always check food temperature before feeding. Always stir heated food to ensure even heat distribution and test the temperature before serving.

CLEANING AND STERILISING

• Before first use, clean the product.
• Clean before each use.
• Always wash the product immediately after use.
• Wash in warm soapy water and rinse in clean water or use a dishwasher. Do not clean with solvents or harsh chemicals.
• Do not allow product to come into contact with oil based foods (e.g. oil/tomato based sauces} as staining will occur.
• Suitable for all forms of sterilisation.

STORAGE AND USE

• Inspect before each use. Throw away at the first signs of damage or weakness.
• Do not store or leave in direct sunlight or near a source of heat.
• Do not store with or allow to come into contact with solvents or harsh chemicals.
• Not suitable for use in a conventional oven or a combination microwave oven with the grill feature switched on.
• Keep all components not in use out of reach of children.

Ref No. 0300035
Model No 1063

Materials listing:
TPE, PPSU Polypropelene, silicone, tissue paper, wood pulp, super absorbent polymer, and polyethylene.

The amazing sleep trainer for young children
Instructions for use

The Gro clock explained…

Stay in bed – When you activate your Gro clock, stars, and hearts appear around a sleeping Ollie. To show the passing of time, the stars disappear at even times during sleep or nap time.
Time to get up – When the clock reaches the wake-up time that you set, the stars disappear, and Ollie wakes up, meaning your child can get up.
After Ollie wakes up, it will remain displayed for two hours, before changing to the energy-saving mode where the digital clock is displayed until re-activated.
The Gro clock has two options – night-time sleep mode and day-time nap mode.

You only need to pre-set the wake-up times you want once (Step 3), but you need to activate the clock (Step 4), each time you use it.
Daily activation of the clock soon becomes part of the bedtime routine and needs to be done in order to set your Gro clock.
Use your bedtime storybook to help explain the Groclock to your child.

What the buttons do

Settings menu

Set time
Set the nighttime sleep mode
Set day–time nap mode
Set audible alarm
Set LED brightness

To set your Gro clock

Step 1 – Plug in the Groclock – the screen showing the digital clock display will appear.
Step 2 – Set the current time

1. Press the scroll down button three times until its shows the settings menu – 5 small flashing icons will appear on your screen
2. Press the enter and the clock icon will flash
3. Press the enter again to select
4. Set the current time using the up and down buttons– select the hour, press enter , select the minutes, press enter , select am or pm, press enter
5. The word ‘On’ will appear. Scroll up or down between ‘On’ or ‘OFF’ depending on if you want the digital clock to be visible while the count-down process is happening. Press enter.

The settings menu screen will return.
Step 3 – Set the wake-up times
You do not set a go-to-sleep time just the wake-up time you want Ollie to wake up. (If you are not intending to use this product for day-time naps, set both night-time and day-time modes to the same ‘wake up’ time).
Night-time sleep mode

1. Whilst on the settings menu screen with the 5 icons flashing, press enter button, and the clock icon will flash
2. Press scroll down so the star image is flashing, press enter to select
3. Select the time that you want the Groclock to ‘wake up’ (the time for your child to get up e.g. 7:00 am) Set the time using the up and down buttons – select the hour, press enter,, select the minutes, press enter, select am or pm, press enter (ensure this is set as AM for a morning ‘wake up’).

Day-time nap mode

1. Whilst on the settings menu screen with the 5 icons flashing, press enter  button, and the clock icon  will flash
2. Press scroll down so the sun image is flashing, press enter to select
3. Select the time that you want the Groclock to ‘wake up’ (the time for your child to get up from their nap e.g. 3:00 pm)
   Set the time using the up and down buttons – select the hour, press enter,, select the minutes, press enter, select am or pm, press enter.

Key lock feature

Key lock deactivates once wake up time has been reached
To switch on key lock –
When the Groclock is activated in night-time sleep or day-time nap mode, press and hold the scroll down button until a cross appears in the big star’s cheek.
The buttons will now be locked.
To turn off key lock Press and hold the scroll down button until you hear a beep.
TIP: Try not to let your child see you set the key lock.

To return to the screen showing the digital clock display, press scroll down. This is the energy-saving mode displayed during the day.
Step 4 – Activate your sleep trainer when putting your child to sleep
To activate the night-time sleep mode

1. From the digital clock screen, press scroll down, the screen will change to an awake Ollie with a small flashing star icon (nighttime sleep) on the left cheek, press enter.
2. The screen will change from awake Ollie to asleep Ollie with small stars around the outer edge, this will now count down to the ‘wake up’ time previously set when the sun will come out.

To activate the day-time nap mode

1. From the digital clock screen, press scroll down twice, the screen will change to an awake Ollie with a small sun icon (day time nap) on the left cheek, press enter.
2. The screen will change from awake Ollie to asleep Ollie with small stars around the outer edge, this will now count down to the ‘wake-up time previously set when the sun will come out.

To return to the menu when the sleep trainer is activated
Press enter, Press scroll down twice, and the settings menu screen will appear. Press scroll down to return to the digital clock.

Additional features

Adjusting the brightness
The brightness level of the screen can be adjusted.

1. From the digital clock display return to the settings menu screen by pressing scroll down three times
2. Press the enter and the clock icon will flash
3. Press scroll down four times until the lightbulb flashes, press enter to select
4. Scroll up and down to desired setting (0 = least bright, 10 = most bright), press enter. For the blue light to remain off in sleep mode set this brightness setting to 0. This means there is no visible blue light in a dark room.
5. Press scroll down to display the digital clock

Setting the audible alarm

The Gro clock has an audible alarm that can be set to go off at any time in any mode.

1. From the digital clock, the display returns to the settings menu screen by pressing scroll down three times
2. Press the enter and the clock icon will flash
3. Press scroll down three times until the alarm bell flashes, press enter to select
4. Select the time you wish the alarm to sound. Set the time using the up and down buttons – select the hour, press enter, select the minutes, press enter, select am or pm, press enter.
5. The bell symbol will start to flash, scroll up or down to desired setting (= off or = on), press enter
6. Press scroll down to display the digital clock

To turn off the audible alarm follow steps 1-4 (above) but on step 5 ensure you select the bell symbol with the cross over it, and press enter, this will turn the audible alarm off.

Frequently asked questions

Q. If the power is turned off, does the clock remember the correct time?
A. When the power goes off, the clock ‘freezes’ all the settings, including the main time, the wake-up times, and brightness settings. Therefore if the power goes off for a few seconds and then back on, the time will have been paused for a few seconds. However if the power was off say for 3 hours, then the time will be out by 3 hours and will therefore need resetting.
Q. If I need to keep the power on should I worry about electricity consumption?
A. Your Groclock uses LEDs so it’s naturally energy efficient. It also has a built-in energy-saving mode.
Q. What is the difference between the night–time and day–time nap mode? 
A. The Groclock works the same way in both modes. The two modes enable two different ‘wake up’ times to be stored, this does not need to be daytime it could be an alternate night-time.
Q. Is there a demo mode so I can show my child how Ollie changes when he wakes up?
A. Yes! To set the demo mode press and hold the scroll up button for three seconds. To turn off the demo mode, press and hold the scroll-up button for three seconds.
Q. My screen has frozen and is not responding to the controls.
A. Switch the Groclock off at the mains, wait a few seconds and switch back on.

For further information visit tommeetippee.com 

Safety

IMPORTANT WARNINGS! Keep this instruction sheet for future reference. These instructions can also be found at www.tommeetippee.com
WARNING. LONG CABLE. STRANGULATION HAZARD. 
Your Groclock is a safe low voltage device, powered from a small mains-operated power unit.
For your continued safety and the reliability of your Groclock, please observe the normal electrical safety precautions:

• This product is not a toy. Please ensure that it is kept out of reach of children and never allow your child to play with either the power unit or the connecting lead
• Keep the product away from water and moisture. It’s intended for indoor use only
• Repairs should be carried out only by a competent engineer. There are no customer adjustments or fuses inside the Groclock case
• The Groclock has been designed to be robust, but it may be broken if dropped
• The connecting lead is a low voltage only, but for reliability reasons, it should be treated with care
• To completely disconnect the power unit, the AC/DC adapter must be unplugged from the mains
• Access to power to supply the AC/DC adapter should not be obstructed whilst in use
• Electrostatic discharge may affect the working of your Gro clock. If this occurs, simply switch the unit off for several seconds and the unit will reset
• The Groclock and AC/DC adaptor shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the Groclock and AC/DC adaptor
• For use only with the power cable supplied with the Gro clock

Mayborn ANZ Pty Ltd. (ABN 66 154 703 134), PO Box 475 Mt Waverley VIC 3149, AUSTRALIA
Newborn Brands (NZ) Ltd. PO Box 47-677, Ponsonby, Auckland, 1144, NEW ZEALAND.
Mayborn (UK) Limited retains all intellectual property rights to this product.
TOMMEE TIPPEE is a registered trademark. Copyright© Mayborn (UK) Limited 2019.
Patent-pending UK, USA, and worldwide PCT patents and Design rights applied for.
Product Ref No: 291345 14171219_1

Technical Information
Height: 13.9 cm
Weight: 285g
Mains Supply Voltage: 230V, 50Hz.
Power Unit: 6V at 200mA.

Information on the disposal for Waste Electrical & Electronic Equipment (WEEE)
This symbol on the products and accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper disposal for treatment, recovery, and recycling, please take these products to designated collection points where they will be accepted on a free of charge basis. In some countries, you may be able to return your products to your local retailer upon the purchase of a new product.
Disposing of this product correctly will help you save valuable resources and prevent any possible effects on human health and the environment, which could otherwise arise from inappropriate waste handling. Please contact your local authority for further details of your nearest collection point for WEEE.
Penalties may be applicable for the incorrect disposal of this product in accordance with national legislation.
When the time comes to dispose of this equipment, please help protect our environment by means of proper disposal. Your local
authorities will have special return and disposal facilities available for you.

Tommee Tippee Perfect Prep Day & Night

IMPORTANT WARNINGS

Keep this instruction sheet for future reference as it includes important information. These instructions can also be found at www.tommeetippee.com
This appliance is intended for household use only. Do not use outdoors.
Before plugging in the Perfect Prep for the first time, ensure that the voltage is compatible with your electricity supply by checking the label on the base of the unit.
Ensure water has been added to the unit before switching the unit on.
Do not immerse in water. To protect against fire, electric shock, and injury to persons, do not immerse cord, plugs or other parts of the unit in water or other liquid.
Misuse of the product may result in the risk of fire, electric shock, and/or personal injury. This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.
Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance.
User maintenance, other than cleaning, descaling and filter replacement is not required for this product. Cleaning and user maintenance shall not be done by children.
Do not touch hot surfaces. When in use the Perfect Prep contains hot water and steam. Keep hands away from dispensing spout as it can cause burns and scalds. Use in a well-ventilated area.
Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. If the supply cord is damaged it must be changed by a qualified person in order to avoid a hazard. If the damage is new the unit must be returned to the manufacturer.
If within a retail warranty period this product should be exchanged at the place of purchase. The manufacturer will then be made aware.
Any questions? Visit our website www.tommeetippee.com 
Always use on a flat heat-resistant surface. Do not move appliances when in use. Do not let the cord hang over the edge of the kitchen work surface or touch hot surfaces. The product has been fitted with a cold wind on the rear of the unit to allow you to adjust the length of the cord safely. It is recommended that the cord be kept as short as possible.  Do not use any accessories other than those supplied with this appliance.
FOR DOMESTIC USE ONLY – NOT INTENDED FOR COMMERCIAL USE

GETTING TO KNOW YOUR PERFECT PREP MACHINE

1. Screen
2. Back button
3. Select button
4. Forward button
5. Water hopper
6. Bottle stand
7. Dispenser outlet

Included inside:
1x 150ml bottle with slow flow teat,
1 x anti-bacterial water filter, milk storage lid

INSTRUCTIONS FOR USE

SET UP:

1. Power on your perfect prep by pressing the middle button.
   When you plug your unit in for the first time you will see this:
2. Press and hold the right button for 3 seconds, then release (a gear icon will appear).
3. Press the middle button to enter settings.
4. Scroll through with left or right to find the preferred language and confirm by pressing the middle button.

• Before you use your Perfect Prep for the first time, you need to run a cleaning cycle and fit your filter.
• Press the select button and then follow the directions on your screen.
•  Once you’ve fitted your filter, the unit will warn you that the tank is empty and that you need to add water.
• Use cold tap water.
• It can take up to 10 minutes for the water to filter through into the base of the unit.
• Once enough water has filtered through, the tank empty warning light will go off and your system is ready to use.

TIP: The select button can be pressed at any time during the cleaning phase to pause the water pumping through.
PRIMING YOUR FILTER

• Only ever handle the filter by holding it by the blue cap.
• Remove the filter from the packaging.
• Remove the sticker from the top of the filter.
• Fill a bowl with cold tap water.
• Submerge the filter in water and gently agitate until the bubbles stop.
• Your filter is now ready to fit into the water hopper.

PRODUCT SETTINGS MENU

• Press and hold the forward button for 3 seconds, then release. This gear icon will appear.
• To scroll through the settings use the back and forward buttons.
• Press the select button to enter a particular setting.
• Settings:
  

MAKING A FEED

• Turn the machine on by pressing the select button.
• Select the feed size you require using the forward and back buttons and follow the directions on the screen.

REPLACING YOUR FILTER
Replacement filters are available from Tommee Tippee Perfect Prep stockists.
Do not use other brands of filters in your machine. Even if they fit, they may not remove the same level of bacteria. Using this machine without a Tommee Tippee water filter could put your child’s health at risk.

• Enter settings menu and scroll across to ‘Fit new filter’.
• Press the select button and then follow the directions on your screen.

PERIODIC CLEANING 
You should clean your machine:

• Before first use then on a 4-weekly basis.
• If your machine hasn’t been used for 1-week.
• When replacing your filter.
  It is advisable to regularly clean the external machine surfaces with a clean cloth (preferably with an antibacterial solution), including the dispenser spout.
• Enter settings menu, then scroll across to ‘Clean unit’.
• Press the select button and then follow the directions on your screen.

DESCALING
The screen will notify you when you need to descale your machine.
The descaling process will remove deposits of calcium and other minerals in the system that may affect its performance.

• Enter settings menu and scroll across to ‘Descale unit’.
• Press the select button and then follow the directions on your screen.

The descaling process can take up to 30 minutes, fortunately, you won’t need to do this very often.
We recommend using food-grade white/clear vinegar to descale your machine when required.
EMPTYING YOUR UNIT

• If you want to drain your machine of water enter the settings menu and scroll across to ‘Empty unit’.
• Press the select button and follow the directions on your screen.

FAQs

Where is the best place to keep my Perfect Prep?
The Perfect Prep should be kept in a cool, dry location, avoiding direct sunlight and kept away from warm appliances. This is recommended to avoid the tank temperature getting too warm.
What does the hotshot do? 
The hotshot helps to dissolve the formula powder quickly and easily, it also kills bacteria that may be present in the formula itself. The water dispensed in the hot shot is at a temperature of over 70°C.
How often do I need to change the filter? 
On average the filter should last around 3 months, however, this depends on the frequency of use and what size bottles you are preparing.
Why do I have to use a Tommee Tippee filter? 
Most standard water filters do not include an anti-bacterial filtration membrane, so even if they fit in your machine, they will NOT remove the same level of bacteria.
Why do I need to submerge the filter before first use?
Submerging primes the filter before use, ensuring that any air bubbles or loose particles within the filter are removed prior to use.
How long can I leave unused water in the tank?
Water is a foodstuff. We recommend using it within 1-2 days.

Dos and Don’ts

It is essential that good hygiene practices are observed in the use and maintenance of your Perfect Prep Machine.
Dos
✓ Ensure your hands and all surfaces that come in to contact with the machine and its components (including filter) are clean.
✓ Before first use clean the machine following the set up steps on the screen.
✓ Keep the machine away from direct sunlight.
✓ Only use cold tap water during regular use.
✓ Keep the outside of the machine clean.
✓ Be careful when handling hot water.
✓ Always adjust the height of the bottle stand so the bottleneck is close to the dispensing spout. This is to maintain the temperature of the water and to avoid any splashes.
✓ Keep well clear of the dispensing spout as the unit produces steam and very hot water.
✓ For your child’s safety always check the food temperature before feeding.
DON’TS
✗ Do not allow the water tank to be contaminated. The inside of the machine should be cleaned by following the cleaning process in this leaflet.
✗ Do not clean with solvents or harsh chemicals.
✗ The machine is intended for use in a kitchen. It is not suitable for use in a nursery.
✗ Do not use hot water other than during cleaning cycles. If the water in the tank is lower than 5°C or higher than 28°C, the machine will not operate. If this happens, either change the water or allow the water to cool and restart.
✗ Do not pour boiling water over the water filter.
✗ When topping up the hopper, do not fill beyond the max icon.
✗ Be careful not to spill any water on the outside of the machine.
✗ Do not remove the back panel from the machine.

INFORMATION ON THE DISPOSAL FOR WASTE ELECTRICAL & ELECTRONIC EQUIPMENT (WEEE)

This symbol on the products and accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper disposal for treatment, recovery and recycling, please take these products to designated collection points where they will be accepted on a free of charge basis. In some countries, you may be able to return your products to your local retailer upon the purchase of a new product. Disposing of this product correctly will help you save valuable resources and prevent any possible effects on human health and the environment, which could otherwise arise from inappropriate waste handling.
Please contact your local authority for further details of your nearest collection point for WEEE. Penalties may be applicable for the incorrect disposal of this product in accordance with national legislation. The product is fitted with a BS 1363 mains plug containing a 5A fuse. If it ever becomes necessary to replace the fuse, only use fuses that are marked BS 1362, and rated at 5A. In the unlikely event that this plug is not suitable for the sockets in your home, it should be removed and a suitable plug fitted as follows:  The wires of the mains lead are colored in accordance with the following code:
GREEN AND YELLOW – EARTH
BLUE – NEUTRAL
BROWN – LIVE
As these colors may not correspond with the colored markings sometimes used to identify the terminals in the plug, connect as follows. The wire colored GREEN AND  YELLOW must be connected to the terminal marked E or by the earth symbol or colored GREEN or GREEN AND YELLOW. The wire-colored BLUE must be connected to the terminal marked N or colored BLACK. The wire colored BROWN must be connected to the terminal marked L or colored RED. If you are in any doubt about how to wire a plug or replace a fuse safely, consult a qualified electrician.
Don’t forget to register your Perfect Prep Machine.
For details of how to do this, go to tommeetippee.co.uk/product-registration

Let us know what you think
We’d love to hear what you think about our products. Share your photos, reviews and tell us about your experiences on our social channels.
helping you Parent On tommeetippee.com 

Mayborn (UK) Limited,
Balliol Business Park,
Newcastle upon Tyne,
NE12 8EW, UK
TOMMEE TIPEEE®. Copyright © 2021
Patented: EP2948032B1
All intellectual property is owned or used under license
by Mayborn (UK) Limited and/or its affiliates
Made in China.
423746
18040321_3

What is the difference between the Tommee Tippee Perfect Prep Day & Night and the Tommee Tippee Perfect Prep?

The Tommee Tippee Perfect Prep Day & Night is a smaller version of the Tommee Tippee Perfect Prep. It is designed to be used in a nursery or child’s bedroom. It has a night light and a timer that can be set for 15 minutes, 30 minutes, 45 minutes or 60 minutes. The timer will automatically shut off after the selected time period has passed. The timer can be set to turn on in the morning as well. The Tommee Tippee Perfect Prep is designed to be used in the kitchen. It has a larger capacity than the Day & Night model and does not have a night light or a timer.

How do I use my Tommee Tippee Perfect Prep?

To use your Perfect Prep, simply fill it with water to the line indicated on your unit, plug it in and press down on the lid until you hear it click into place. You can then place your baby’s bottles inside and push down on them until they reach just below the water line. This will prevent any milk from leaking out of the bottle when you go to feed your baby later on. You can also place your baby’s pacifiers in your unit to keep them clean and germ free while you are away from home.

How do I clean my Tommee Tippee Perfect Prep?

Your Tommee Tippee Perfect Prep comes with an easy-to-use cleaning brush that allows you to easily remove any milk residue that may have built up inside of your unit over time. Simply fill your unit with warm water, add some dish soap and allow it to sit for about 10 minutes before using your cleaning brush to scrub away any milk residue that may be present inside of your unit. After scrubbing away any residue, rinse out all of the soap from inside of your unit and allow it to air dry for 24 hours before using it again.

Why does my water leak out of my Tommee Tippee Perfect Prep?

If you are having trouble with water leaking out of your unit, make sure that you have filled it to just below the water line indicated on your unit before placing any bottles inside of it or else this will cause water to leak out onto your countertop or table when you place bottles inside of it later on. You should also make sure that you have pushed down on each bottle until they reach just below the water line as well before placing them inside of your unit as this will prevent any milk from leaking out onto your countertop or table later on as well. If you are still having trouble with leaks after filling up your unit properly, try adding some white vinegar into one side of your unit while leaving the other side empty so that air bubbles can form in between both

What does a day and night prep machine do?

The Perfect Prep day & night machine makes bottle feeding a dream. It preps the perfect bottle in just two minutes, for stress-free bottle feeding at any time of the day or night. Contains a pre-loaded filter that will last up to three months.

Can you use any bottles with Perfect Prep Machine?

As long as your bottle isn’t oversized, there shouldn’t be any drawbacks to using the Prep Machine with another bottle brand

Can you reuse perfect prep machine?

Just make sure you replace the filter and follow the cleaning instructions on the perfect prep website before reusing. If your machine is Tommee Tippee like mine, you can find the instructions HERE

How do you clean a perfect prep machine storage?

For this reason you need to manually flush the hot water through the unit by pressing this button the cleaning mode button and hold for two seconds. The cleaning mode light will illuminate the boiled

What do the red lights mean on Tommee Tippee prep machine?

descaling soon
A red warning light will illuminate when the unit requires descaling soon. If the light flashes, you should descale immediately.

Why is temperature light on prep?

Due to recent weather changes, you may find that your temperature warning light has decided to come on! Don’t worry, this is a key safety feature and can be easily resolved. The Perfect Prep Machine contains a probe that measures the temperature of the water in the tank, preventing it from dispensing water above 25 C

How does the Perfect Prep machine work?

The Perfect Prep automatically controls the quality, volume and temperature of water in making up a formula feed. Once the water is in the hopper it passes through a unique filter to remove bacteria and other impurities in the water

Can I give my baby water from perfect prep machine?

My LO is 4 weeks and takes the water from the prep machine. Has done for roughly a week, no problems. HV happy with it.