Introduction

Congratulations on your purchase of the wireless indoor/ outdoor humidity and temperature monitor. You will now be able to know the outdoor/indoor temperature and humidity while sitting inside.

General Warning

DANGER!

This device contains electronic components which operate via a power source (power supply and/or batteries). Do not let children use the device while unattended. Only use the device as described in the manual, otherwise you run the risk of an electric shock.

Children should only use the device under adult supervision.
Keep packaging material, like plastic bags and rubber bands, out of the reach of children,as they pose a choking hazard.

Keep batteries out of the reach of children. Make sure you insert the batteries correctly. Empty or damaged batteries could cause burns if they come into contact with the skin. If necessary, wear adequate gloves for protection.

DANGER!

Do not expose the device to high temperatures.Use only recommended batteries. Do not shortcircuit the device or batteries, or throw them into a fire. Excessive heat or improper handling could trigger a shortcircuit, a fire or an explosion!

NOTE!

Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.

Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. The batteries should be removed from the unit if it has not been used for a long time.

Notes on cleaning

Separate the device from the power supply or remove the batteries before cleaning.
Only use a dry cloth to clean the exterior of the device.
Do not use any cleaning fluid to avoid damaging the electronics.

Hints and Tips

If the receiver does not connect to the transmitter, try the following:

• Press and hold the CHANNEL/SYNC button on the base station and then press TX button on the transmitter.
• Relocate the base station and/or the remote unit until connection is found.
• Signals from other electronic devices may cause interference. Place the base station and receiver away from these devices.
• The transmitter may not function properly in extreme temperatures due to battery power. Replace the batteries or the unit will resume proper function in more moderate weather.
• If the base station is attached to a refrigerator or a metal object by magnet, the transmission may be shorter.
  Remove the base station from the refrigerator or the metal object or place the base station and remote sensor as close as possible.
• If the Humidity is lower than 10%, it will display LLL.

Warnings

• Do not subject the unit to excessive force, shock, dust, temperature or humidity.
• Do not immerse the unit in water.
• Do not remove any screws.
• Do not dispose this unit in a fire. IT MAY EXPLODE.
• Keep unit away from small children. The unit or parts of the unit might be a choking hazard.
• Never attempt to recharge the batteries using any other methods.
• Dispose of the unit legally and recycle when possible.

Components

1. One base station unit (Receiver).
2. One remote sensor (Transmitter).

Although the remote sensor is designed to be rainproof, the remote sensor must be always placed upwards so that rain won’t get inside the sensor through the vent holes on the bottom of the senor which functions to let the remote sensor detect the environmental temperature and humidity more precisely and quickly.

Indoor Base Station (Receiver) Features

1. Outdoor temperature
2. Outdoor humidity
3. Indoor temperature
4. Indoor humidity
5. Stand
6. Channel/SYNC
7. °C/°F/All time/24
8. MAX/MIN/Clear
9. Battery Compartment

• LCD display: Displays the current outdoor humidity/ temperature and indoor humidity/temperature.
• Battery Compartment: Holds 2 AAA batteries to power the unit.
• Tabletop and wall-mounted design.
• Indoor Temperature range: -4°F~158°F(-20°C~70°C).
• Humidity range: 10% ~ 99%.
• Temperature display unit: °C and °F selectable.
• Temperature Resolution: 0.1 °C/°F.
• Humidity Resolution:1%.
• Low battery indication.

Buttons

• CHANNEL/SYNC: Press once to display the temperature humidity readings from up to 3 outdoor remote sensors; Press and hold this button to enter the synchronization mode. and
• MAX/MIN/CLEAR: Press once to display the maximum minimum temperature and humidity; Press and hold to clear the history data.
• F/°C/ALL-TIME/24: Press to select the temperature display in ºC or ºF; When the display shows the maxi-mum or minimum temperature and humidity, press this button once to set the maximum and minimum data record time interval between ALL TIME or 24 hours. Note: Both ALL TIME and 24 hours represent the time since you last time manually cleared the history data or installed a new battery.

Temperature & Humidity Trend

1. indicates the temperature & humidity is in an increasing trend.
2. indicates the temperature & humidity is in an no change trend.
3. indicates the temperature & humidity is in a decreasing trend.

Outdoor Remote Sensor (Transmitter) Features

1. TX LED
2. Wall hanging hole
3. RESET
4. TX
5. Channel 1.2.3
6. 2*AAA battery
7. Sensor detection port

• Battery Compartment: Holds 2 X AAA batteries to power the unit.
• Rain-proof and wall-mounted design.
• Outdoor Temperature range: -4°F~158°F(-20°C~70°C).
• Humidity range: 10% ~ 99%.

Buttons

• CHANNEL Selector (1,2,3): Slide to set Channel 1,2 or 3
• RESET: Press once to reset the remote sensor.
• TX: Press to send temperature/humidity data to the receiver manually.

Battery Installation and Setup

1. Open the battery compartment of the remote sensor below Figure;
   
2. Slide the channel selector switch inside the battery compartment to your desired channel. For the first remote you may select any channel, for additional remotes select any unused channel;
3. Insert (2) AAA batteries according to the polarity markings. Replace the battery compartment cover;
4. Open the battery compartment at the back of the base station and insert (2) AAA batteries according to the polarity markings. Replace the compartment door;
5. Press the °F /°C button at the back of the base station to display the temperature in °F or °C.

Note:

Do not mix old and new batteries.
Do not mix alkaline, standard (carbon zinc), or rechargeable (nickel cadmium) batteries.

For maximum performance in normal conditions we recommend using good quality alkaline batteries.
If the battery power is low, there will be low battery icon showing on the base station display.

Synchronize Remote Sensors with The Base Station

Please note: each time the batteries (inserted into either base station or remote sensor) are replaced or base station/ remote sensor lost connection, make sure to follow the below synchronization process to pair and re-connect the base station and remote sensor:

1. Position the remote sensor near the base station;
2. Once the batteries are installed in the base station, the signal icon . (located on the upper left of the base station display) will flash for 3 minutes, indica-ting that the base station is in synchronization mode: it is waiting for remote sensors to be registered. RF
3. If 3 minutes have passed after the batteries were installed in the base station and the RF signal Icon is no longer flashing, press and hold the CHANNEL/SYNC button on the back of the base station for 3-4 seconds until the RF signal icon is flashing again to set it back in synchronization mode;
4. Install the batteries in the remote sensor and wait for a moment or just press either the TX or RESET button inside the remote sensor battery compartment, the remote sensor temperature/humidity will show on the base station display which indicates the synchronization is complete.
5. If you have additional remote sensors, repeat the above steps to register the remote sensors (up to 3 remote sensors can be registered with one base station);
6. If you have registered more than one sensor, press the CHANNEL/SYNC button on the base station to select the remote channel you want displayed permanently on the base station. Press CHANNEL/SYNC button until you observe a circular arrow on the base station LCD display under the channel number. The unit will then auto-scroll, changing from channel to channel every 5 seconds. Press CHANNEL/SYNC button until you observe the circular arrow disappear. The unit will stop cycling.
   

NOTE: If you have additional remote sensors, when you synchronizing remote sensors with the base station, the unit will keep changing from channel to channel in the first three minutes, after that you can select any channel you like or auto-scroll mode.

Place the Base Station and Remote Sensor

1. The indoor base station (receiver) should always be placed in a well ventilated indoor area and located away from vents, heating or cooling elements, direct sunlight, windows, doors, or any other openings.
2. The remote sensor (transmitter) can be placed on a flat surface indoor or outdoor. Make sure the sensor is within the transmission distance from the base station and with minimal obstructions.
3. The base station and remote sensor can both be wall mounted.

NOTE: Although the remote sensor is designed to be proof, the remote sensor must be always placed upwards so that rain won’t get inside the sensor through the vent holes on the bottom of the senor which functions to let the remote sensor detect the environmental temperature and humidity more precisely and quickly.

Maximum & Minimum Recorded Temperature & Humidity

1. Press MAX/MIN/Clear button once to display the highest indoor and outdoor temperatures/humidity recorded since last reset. MAX is shown on the display.
2. Press MAX/MIN/Clear button again to display the lowest indoor and outdoor temperatures/humidity recorded since last reset. MIN is shown on the display.
3. To clear and reset the max/min records, when either the MAX or MIN record is shown on the LCD display, press and hold MAX/MIN/Clear for 3 seconds.
4. When either the MAX or MIN record is shown on the LCD display, press ALL-TIME/24 button once to set the data record time interval between ALL TIME or 24 hours. Note: Both ALL TIME and 24 hours represent the time since you last time manually cleared the history data or battery installation.

Purchasing Additional Remote Sensors

The model number of the remote sensor for this unit is TPR65.
Additional sensors may be ordered directly from Amazon or ThermoPro by contacting our customer service listed below.

Specifications

1. Transmission frequency: 433 Mhz.
2. Maximum transmit power: 8 mW.
3. Transmission range up to 200 ft. (range maybe shorter based on interference present).
4. Indoor Temperature range: -4°F~158°F (-20°C~70°C).
5. Outdoor Temperature range: -4°F~158°F (-20°C~70°C).
6. Humidity range: 10% ~ 99%.
7. Temperature tolerance: +/- 2.0°F (+/- 1.1°C).
8. Humidity tolerance: ±2% from 30% to 80%; ±3% below 30% and above 80%.
9. Power: 2 X AAA 1.5V for base unit and 2 X AAA 1.5V remote sensor.

FCC Statement of Compliance

This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Declaration of Conformity

Hereby, the manufacturer declares that this product complies with the basic requirements and applicable regulations of the EMC Directive 2014/30/EU. The complete declaration of conformity can be found at: https://itronicsmall.com/eu-declaration-of-conformity/

Disposal

Meaning of the “Dustbin” Symbol

• Protect our environment: do not dispose of electrical equipment in the domestic waste.
• Please return any electrical equipment you will no longer use to the collection points provided for their disposal. that
• This helps avoid the potential effects of incorrect disposal on the environment and human health.
• This will contribute to the recycling and other forms of reutilisation of electrical and electronic equipment.
• Information concerning where the equipment can be disposed of can be obtained from your local authority.

CAUTION: Batteries/rechargeable batteries must not be disposed of with household waste!

• The batteries must be removed from the appliance.
• Take spent batteries to the appropriate collection point or to a dealer.
• Your town or local authority can provide information about public collection points.

This symbol can be found on batteries/rechargeable batteries which contain hazardous.

• Pb = contains lead
• Cd = contains cadmium
• Hg = contains mercury
• Li = contains lithium

Limited One-year Warranty

ThermoPro warrants this product to be free of defects in parts, materials and workmanship for a period of one year, from date of purchase.

Should any repairs or servicing under this warranty be required, contact Customer Service by phone or email for instructions on how to pack and ship the product to ThermoPro.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Customer Service

Telephone: 1-877 515 7797 (USA & Canada only)
44-203-769-1321(UK)
Email:
Hours: Weekdays 8:00 AM- 8:00 PM EST(USA & Canada only)
1:00 PM – 12:00 PM CET(UK)

V20180802

General Warning

This device contains electronic components which operate via a power source (power supply and/or batteries). Do not let children use the device while unattended. Only use the device as described in the manual, otherwise you run the risk of an electric shock.

Children should only use the device under adult supervision. Keep packaging material, like plastic bags and rubber bands, out of the reach of children, as they pose a choking hazard.

Keep batteries out of the reach of children. Make sure you insert the batteries correctly. Empty or damaged batteries could cause burns if they come into contact with the skin. If necessary, wear adequate gloves for protection.

Do not expose the device to high temperatures. Use only the recommended batteries. Do not short circuit the device or batteries, or throw them into a fi re. Excessive heat or improper handling could trigger a short-circuit, a fi re or an explosion!

Do not disassemble the device. In the event of a defect, please contact your dealer. The dealer will contact the Service Centre and can send the device in to be repaired, if necessary.

Use only the recommended batteries. Always replace weak or empty batteries with a new, complete set of batteries at full capacity. Do not use batteries from different brands or with different capacities. The batteries should be removed from the unit if it has not been used for a long time.

Notes on cleaning

Separate the device from the power supply or remove the batteries before cleaning. Only use a dry cloth to clean the exterior of the device. Do not use any cleaning fluid to avoid damaging the electronics.

1. Display: Displays the current humidity and temperature, and record maximum and minimum
   humidity/temperature.
2.  °C/°F/Clear Button: Press once to change the temperature display to either °C or °F. Press and hold for 2 seconds to clear the record maximum and minimum humidity/temperature readings.
3. Battery Compartment: Holds one 1 AAA to power the unit.
4. Comfort Level: 3 icons: DRY, COMFORT, WET. If humidity is below 30%: Dry If humidity is between 30% to 60% AND temperature is between 68°F ~ 79°F(20°C ~26°C): Comfort If humidity is above 60%: Wet. Elsewise: No icon.
5. Totally wireless tabletop and magnet mountable design.

Before first use

1. Insert or Replace Battery: Insert one AAA battery with correct polarity (+) and (-) as indicated.
2. Do not immerse product in water.
3. The humidity and temperature monitor is now ready to use.

Care of your Humidity/Temperature monitor

• Do not leave exposed to extreme high or low temperatures since this may cause damage to electronic parts and plastics.
• Remove battery if planning to store for more than four months.

Specifications

1. Temperature range: -58°F ~ 158°F(-50°C ~ 70°C).
2. Humidity range: 10% ~ 99%.
3. Comfort display: DRY, COMFORT, WET.
4. Temperature display unit: °C °F selectable
5. Temperature Resolution: 0.1 °C/°F
6. Humidity Resolution: 1%.
7. Refresh rate: 10 seconds.
8. Power supply: 1 X AAA 1.5V

Declaration of Conformity

Hereby, the manufacturer declares that this product complies with the basic requirements and applicable regulations of the EMC Directive 2014/30/EU. The complete declaration of conformity can be found at:

https://itronicsmall.com/eu-declaration-ofconformity/

• Protect our environment: do not dispose of electrical equipment in the domestic waste.
• Please return any electrical equipment that you will no longer use to the collection points provided for their disposal.
• This helps avoid the potential effects of incorrect disposal on the environment and human health.
• This will contribute to the recycling and other forms of reutilization of electrical and electronic equipment.
• Information concerning where the equipment can be disposed of can be obtained from your local authority.

• The batteries must be removed from the appliance.
• Take spent batteries to the appropriate collection point or to a dealer.
• Your town or local authority can provide information about public collection points.

This symbol can be found on batteries/rechargeable batteries which contain hazardous:

Pb = contains lead
Cd = contains cadmium
Hg = contains mercury
Li = contains lithium

Limited one-year Warranty

ThermoPro warrants this product to be free of defects in parts, materials and workmanship for a period of one year, from date of purchase.

Should any repairs or servicing under this warranty be required, contact Customer Service by phone or email for instructions on how to pack and ship the product to ThermoPro.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

Customer service

Telephone: 1-877-515-7797(USA & Canada only)
44-203-769-1321(UK)

Email: [email protected]

Hours: Weekdays 8:00 AM- 8:00 PM EST(USA &
Canada only)
Weekdays 1:00 PM – 12:00 PM CET(UK)

Introduction

Congratulations on your purchase of the Professional Remote Food Thermometer a programmable radio frequency food thermometer. You will now be able to remotely monitor the temperature of cooking food and the temperature inside your grill, oven, or smoker from anywhere in your home.

Components

1. One receiver unit.
2. One transmitter unit.
3. Two detachable stainless steel probes with steel mesh cable.
4. Four AAA batteries.

Receiver Features

• LCD (Liquid Crystal Display) – Displays all icons, temperature, and time.
• Dual probe temperature display.
• Programmable alert with preset temperatures for specific foods.
• 99-hour, 59-minute countdown timer and count up timer
• Temperature range of probe: 32˚F to 572˚F (0˚C to 300˚C).
• Temperature tolerance of internal food reading: +/-1.8˚F (+/-1.0˚C).
• Battery compartment – Holds 2 AAA batteries.
• Belt clip/Stand – Belt clip allows you to be mobile. Clip the receiver unit to the belt. Swings out and allows you to stand the receiver on the tabletop as well.

Buttons

1. MODE – Press to select Thermometer Probe 1, Thermometer Probe 2, or Timer mode. Press and hold for 2 seconds to enter Synchronization/Pairing mode.
2. ▲– In thermometer mode (Probe 1 or 2), press once to increase the temperature value. Press and hold for 2 seconds and the temperature value will increase at a faster pace. In timer mode, press once to increase Hour, A minute, or Second setting. Press and hold for 2 seconds, the hours, minutes, or seconds will increase at a faster pace.
3. – In thermometer mode (Probe 1 or 2), press once to decrease the temperature value. Press and hold for 2 seconds, the temperature value will decrease at a faster pace. In timer mode, press once to decrease the Hour, Minute, or Second setting. Press and hold for 2 seconds, the hours, minutes, or seconds will decrease at a faster pace.
4. S./S./ /CLEAR – When setting the timer, press to confirm the setting. When the timer setting is set, press once to start the timer. When the timer is running press once to pause the timer. Press and hold for two seconds to clear the timer setting. Press it to turn ON/OFF the alarm in BBQ mode.
5. MEAT – In thermometer mode, press to select the meat type: PROG (program – User Self-Defined), GBEEF (Ground Beef), GPOUL (Ground Poultry), BEEF, VEAL, CHCKE (Chicken), PORK, POULT (Poultry), LAMB, FISH & HAM and BBQ. In Timer mode, press to select Hour, Minute mode, or Minute’ second” mode.
6.  TASTE – In thermometer mode, press to select the meat taste level: RARE, MED RARE, MEDIUM, MEDIUM WELL, and WELL DONE. In BBQ mode, press it to
   display HI or LO BBQ temperature.
7. /ºF/ºC–Press once to turn on or off the backlight, press and hold for 2 seconds to select temperature readings in Celsius or Fahrenheit.
8. – Press once to turn ON/OFF the receiver.

LCD Screen

Transmitter Features

• LCD (Liquid Crystal Display) – displays temperatures of both probe 1 and probe 2. It will automatically switch between probe 1 and probe 2 displays.
• Wire Stand – This allows you to stand the transmitter on a tabletop or it can be reversed and used as a hanger.
• Battery Compartment – holds 2 AAA batteries.
• Sensor socket hole – Plug-in for stainless steel probe 1 and probe 2.
• Transmission frequency: 433 Mhz.
• Maximum transmit power: 8 mW.

Button

ºF/ºC/ – Press once to turn on or off the transmitter. Press and hold for 2 seconds to select the transmitter temperature display in ºC or ºF.

Installing batteries

Open the battery compartment of the receiver and insert two “AAA” batteries with correct polarity. Open the battery compartment of the transmitter and insert two “AAA” batteries with the correct polarity.

Turn On/Off Unit

Press the button on the receiver to turn on/off the receiver;
Press the ºF/ºC /button on the transmitter to turn on/off the transmitter.

Synchronize/Pair Transmitter and Receiver

The transmitter and receiver were already paired at our manufacturing facility. Usually, you do NOT need to re-synchronize or re-pair the units. You just plugin the probes, insert batteries, turn on the receiver and the transmitter and wait for a few seconds, you will see the temperatures shown on both receiver and transmitter, and the units are ready for use.
However, in some unusual cases, the transmitter and receiver are no longer paired, then you may need to re-synchronize them by following the below steps:
a. Insert the stainless steel probes into the corresponding plugs in the transmitter.
b. Turn on the transmitter by pressing the ºF/ºC /button. The transmitter will show the current temperatures on its LCD display.
c. Turn on the receiver by pressing the button.
d. Press and hold the Mode button on the receiver for 2~3 seconds to enter the synchronization mode which will last for 60 seconds. The display shows “—” and it is flashing.
e. Wait for a moment until the temperature reading shows on the receiver display, it means the synchronization/Pairing is complete. Your professional remote cooking thermometer is now ready for use.
Note: The synchronization between the transmitter and the receiver won’t be lost even if you replace the batteries.

Loss link alert

If the receiver is taken out of range or there is abnormal external interference or after shutting off the transmitter, the receiver may not be able to receive the transmission from the transmitter. If this happens for over 4 minutes, the unit will alert you the signal is lost. Pressing any button on the Receiver will stop the Loss Link beep.
To regain the transmission signal, move the receiver closer to the transmitter, the link should be automatically restored and the temperatures should appear on the receiver display.

Auto-Off Feature

The receiver will turn off automatically if it hasn’t received the temperature signal from the transmitter for more than 30 minutes, a beep will sound for one minute before it shuts down. However, the Auto-Off feature will be automatically disabled if the timer is running.

Measure meat temperature to USDA doneness temperature range

1. You can use two probes (Probe 1 and Probe 2) to measure and monitor the temperatures of two pieces of meat or two sections of the same large piece of meat at the same time.
2. Press MODE to select Thermometer Mode, Probe 1 or Probe 2, represented by a small icon (PROBE 1 or PROBE 2) on the upper display.
3. Press MEAT to select meat type: PROG (Program – User self-defined), GBEEF (Ground Beef), GPOUL (Ground Poultry), BEEF, VEAL, CHCKE (Chicken), PORK, POULT (Poultry), LAMB, FISH & HAM.
4. Press TASTE to select the level of doneness for the meat type selected: RARE, MED RARE, MEDIUM, MEDIUM WELL and WELL DONE.
   Note: The temperature displayed to the left of the actual meat temperature will show the preset temperature TEMP SET according to USDA doneness levels. Example: Beef will be Well Done at 165 F.º
5. Once the temperature of the meat (Probe 1 or Probe 2) reaches the preset doneness level, the receiver will beep and the LCD backlight will be turned on.
   press any button to stop the beep.

Measure meat temperature set to your specific taste

1. Press MODE to select Thermometer Mode, Probe 1 or Probe 2.
2. Press▲ or ▼raise or lower the set temperature. As you press ▲ or ▼ the display changes to PROG (program). Press and holding the button will raise or lower the temperature setting rapidly. Pressing MEAT will return you to the preset USDA ranges.
3. Once the temperature of the meat reaches the preset doneness level, the receiver will beep and the LCD backlight will be turned on. Press any button to stop the beep.

How to Monitor BBQ/Oven Temperature

1. You can use probe 2 to measure and monitor the temperature inside the BBQ, smoker, or barbeque. Clip the probe to the grill rack of BBQ, or oven rack.
2.  Press MODE to select Probe 2.
3. Press MEAT repeatedly until the display shows BBQ.
4. Press ▲ or ▼ set your desired temperature of the HI BBQ setting. Press and hold the ▲ or ▼ button to make the adjustment faster. The HI BBQ temperature range is 140 ºF – 572 ºF and the default setting is 250 ºF.
5. Press the TASTE button to switch to the LO BBQ setting. Press ▲ or▼ set the desired temperature of the LO BBQ setting. Press and hold the ▲ or ▼ button to make the adjustment faster. The LO BBQ temperature range is 32 ºF – 554ºF and the default setting is 225 ºF.
6. Press the S./S./ /CLEAR button to turn on/off the alarm function.
7. Press the TASTE button to display the High or Low-temperature setting.
   (Note: the HI BBQ setting will not allow you to set the temperature below the LO BBQ setting. LO BBQ temperature is always lower than the HI BBQ temperature by 2ºF)

Note: The LO BBQ temperature alarm will not be activated until the actual BBQ temperature goes above the set LO temperature.

Procedure for typical use on an outdoor grill

The following typical example will go through the steps to have the Professional Remote Cooking Thermometer alert you when you cook two pieces of beef steak at the same time with one piece of beefsteak to be cooked to medium (USDA doneness level) and the other piece of beefsteak to be cooked to medium well  (USDA doneness level).

1. Turn on the grill.
2. Place two pieces of beef steak on the grill rack.
3. Insert probe sensor 1 into the center of the thickest portion of the first piece of steak. Avoid touching bone or heavy fat areas. Insert probe sensor 2 into the second piece of steak. Assume you would like to cook the first piece of steak to medium and the second piece to medium-well.
4. Position the probe sensor wire so they will not come into contact with flames and exit the grill surface area without being pinched/crushed by the grill cover.
5. Stand the transmitter away from the heat source of the grill. DO NOT put a transmitter on the closed cover or under the cover. The transmitter is not waterproof. DO NOT use in the rain.
6. Press Mode to select Thermometer Probe 1. Press MEAT so BEEF is displayed.
7. Press TASTE so MEDIUM is displayed and 150 F will be shown as the TEMP SET.
8. Press MODE to change Thermometer Probe 2. Press MEAT so BEEF is displayed.
9. Press TASTE so MEDIUM WELL is displayed and 160 F will be TEMP SET.
10. You may take the receiver up to 300 feet away from the outdoor grill. Go indoors if desired.
11. When the temperature of the first piece of the steak reaches 150 F MEDIUM, the receiver will beep and the LCD backlight will be turned on.
12. Press any button to turn off the alert.
13. Take the first piece of steak out of the grill.
14. When the temperature of the second piece of the steak reaches 160 F MEDIUM WELL, the receiver will beep and the LCD backlight will be turned on.
15. Press any button to turn off the alert.
16. Turn off the grill. Remove the probe sensors from both steaks. Always wear a heat-resistant glove to touch the stainless steel probe sensor or wire during or just after cooking. Do not touch with bare hands.
17. Clean the stainless steel probe and dry thoroughly after each and every use.
18. Turn off the transmitter and receiver.

Using the Timer

Count down

1. Press the MODE button to select the TIMER mode. The timer 00:00 with a small icon TIMER will be shown in the upper part of the display.
2. Press MEAT to switch between Hour: Minute timer to a minute’ second” timer and back.
3. Press ▲ or ▼adjust the timer setting. Press and hold ▲ or ▼adjust the setting at a faster pace. Press S./S./ /CLEAR to confirm the setting. The maximum countdown timer setting is 99 hours and 59 minutes.
4. Press and hold S./S./ /CLEAR to clear the setting back to 00:00.
5. After setting, press to start the timer. TIMER will blink S./S./ /CLEAR ▼    indicating the countdown timer is running.
6. To pause the countdown process, press the S./S./ /CLEAR button.
   The TIMER▼ becomes solid. Press the S./S./ /CLEAR button to continue the timer.
7. When the countdown timer reaches 00:00, an alarm will sound and the backlight will be on for one minute.
   Note: When the timer counts down below 1 hour 1:00, the display will cally change to 59’59” to indicate, 59 minutes 59 seconds. The seconds will be shown counting down then. When the countdown reaches 0’00” the timer starts counting up and it will beep for 60 seconds. Press any button to stop the timer.

Count up

1. Press the MODE button to select the TIMER mode, The timer 00:00 with a small icon TIMER will be shown in the upper part of the display. If the timer setting is not 00:00, press and holds S./S./ /CLEAR to clear the setting to 00:00.
2. Press the S./S./ /CLEAR button to start count up. The TIMER ▲will blink indicating the count-up timer is running. The maximum count up that can be reached is 99 hours and 59 minutes.
3. To stop the count-up process, press the S./S./ /CLEAR button. The ▲TIMER ▲ becomes solid.
4. Press and hold S./S./ /CLEAR to clear the setting back to 00:00.
5. When the count-up timer reaches 59 minutes and 59 seconds, it will automatically change to Hour: Minute display format.

Helpful Hints

• If the receiver and/or the transmitter display LLL or HHH instead of the probe temperature, wait for the probe to reach room temperature. If LLL or HHH is still displayed or you get a false temperature, squeeze the probe jacks harder into the transmitter and twist them back and forth so they make good contact. If the problem still persists, it is likely the internal probe wire has shorted out either through moisture or heat damage.
• Do not immerse the probe in the water while cleaning.
• Do not allow the probe or probe wire to come into contact with flames.
• Within the warranty period return the defective probe to address below along with a return address and we will send you a replacement probe at no charge.
• If the temperature displayed seems to read too high or the temperature seems to increase too quickly, check to make sure the probe tip is not poking through the food. Reposition the probe tip in the center of the thickest part of food. Avoid touching bone or heavy fat areas.

Cautions:

1. Always wear a heat-resistant glove to touch the stainless steel probe sensors or wires during or just after cooking. Do not touch with bare hands.
2. Keep the stainless steel probe sensors and wires away from children.
3. Clean the stainless steel probes and dry thoroughly after each and every use.
4. Do not use the unit in the rain. It is NOT rainproof.
5. Do not expose the plugs of the stainless steel probes or the plug-in holes of the transmitter to water or any liquid. This will result in bad connections and faulty readings.
6. Do not expose the receiver or transmitter to direct heat.
7. Do not use stainless steel probes in a microwave oven.
8. The Probe Thermometer registers temperatures as low as 32 ºF (0 ºC) and as high as 572 ºF (300 ºC). LLL will be displayed below 32 ºF and HHH will be displayed above 572 ºF. Do not use the stainless probe sensor above 572 ºF. Doing so will deteriorate the wire.
9. Not intended for use by persons aged 12 and under.

Cleaning

1. Always wear a heat-resistant glove to touch the stainless steel probe sensors or wires during or just after cooking. Do not touch with bare hands.
2.  Keep the stainless steel probe sensors and wires away from children.
3. Wash the metal probe tips with hot soapy water and dry thoroughly. Do not immerse the probe in the water while cleaning.
4. Wipe the transmitter and receiver with a damp cloth. Do not immerse either in water.

FCC Compliance

Information to user
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the users’ authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Declaration of Conformity

Hereby, the manufacturer declares that this product complies with requirements and applicable regulations of the Radio Equipment Directive 2014/53/EU, the EMC Directive 2014/30/EU. The complete declaration of conformity can be found at: https://itronicsmall.com/eu-declaration-of-conformity/

Disposal

Meaning of the “Dustbin” Symbol

• Protect our environment: do not equipment in the domestic waste. dispose of electrical equipment that you will no longer
• Please return any electrical use to the collection points provided for their disposal
• This helps avoid the potential effects of incorrect disposal on the environment and human health.
• This will contribute to the recycling and other forms of reutilisation of electrical and electronic equipment.
• Information concerning where the equipment can be disposed of can be obtained from your local authority.

CAUTION: Batteries/rechargeable batteries must not be disposed of with household waste!

• The batteries must be removed from the appliance.
• Take spent batteries to the appropriate collection point or to a dealer.
• Your town or local authority can provide information about public collection points.

This symbol can be found on batteries/rechargeable batteries that contain hazardous:

Pb = contains lead Cd = contains cadmium Hg = contains mercury Li = contains lithium

LIMITED ONE-YEAR WARRANTY

ThermoPro warrants this product to be free of defects in parts, materials, and workmanship for a period of one year, from the date of purchase.
Should any repairs or servicing under this warranty be required, contact Customer Service by phone or email for instructions on how to pack and ship the product to ThermoPro.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

CUSTOMER SERVICE

Telephone:
44-203-769-1321(UK)
1-877-515-7797(USA & Canada only)
Email: [email protected]
Hours: Weekdays 1:00 PM – 12:00 PM CET(UK) 8:00 AM- 8:00 PM EST(USA & Canada only)

Measure meat temperature to USDA doneness temperature range

PRODUCT

1. LCD Display: Displays the current temperature.
2. LOCK: Press once to lock the current temperature for 5 seconds, press again to unlock .
3. LIGHT: Press once to turn ON/OFF the backlight 4 C/°F:
4. Hold for 3 seconds to switch between °C and °F .
5. CAL: Press and hold it for 5 seconds to calibrate the unit. Press again to confirm the calibration.
6. Battery Compartment: Use 1 x AAA battery to power the unit.
7. Temperature Probe: Insert the probe into food to get the internal meat temperature.
8. Super-Fast Temperature Probe: High precision sensor, you can get a temp readout within 3-4 seconds  .
9. Waterproof: IP65.
10. Auto-rotating displays.
11. Motion-sensing sleep and wake modes.
12.  Built-in magnets.
13. Temperature chart.

SPECIFICATIONS

1. Temperature range: -58°F ~ 572°F (-50 °C ~ 300 °C). If the temperature is below -58°F (-50 °C) or above 572 °F (300 °C), LLL or HHH will show on the screen
2. Three  Buttons: LOCK, LIGHT, C/°F.°3
3. 90 seconds Auto-off feature .
4. Resolution: 0.1 °C/°F .
5. Temperature Accuracy: ±0.9°F (±0.5°C) in range between 14 to 212°F (-10 to 100°C) .
6. Battery: 1 x AAA 1.5V included

BEFORE FIRST USE

1. Insert 1* AAA battery with correct polarity (+) and (-) as indicated.
2. Wash probe tip with warm soapy sponge or cloth, then rinse and dry.
3. Wash under running water without fear!.
4. PLEASE READ AND FOLLOW ALL  INSTRUCTIONS.
5. The thermometer is now ready to use.

TO MEASURE FOOD TEMPERATURE

1. Pull the probe away from the body of the thermometer to turn on the thermometer, and fold in the probe to turn off the thermometer.
2. Press and hold the °C/°F button for 3 seconds to switch between °C and °F. Please note that the temperature unit selected will remain when you turn on the thermometer next time.
3. Insert the tip of the probe into food being cooked as shown in the picture below. The thermometer will start to measure the internal food
   temperature.
4. Wait until the temperature reading stabilizes on the display.
5. The temperature reading can be displayed with a 360° global viewing angle.
6. Press the LOCK button to hold the temperature for 5 seconds.
7. Wash the thermometer under running water after use.
8. The thermometer will automatically turn off if the probe is not folded in and no button has been pressed in 90 seconds.
9. If the thermometer is sleeping with the probe not folded in and then picked up or moved, the thermometer will automatically power on.

CALIBRATION

The thermometer comes with a Calibration feature. In most cases, the thermometer was calibrated precisely at our manufacturing facility, and generally, you do NOT need to calibrate the thermometer. However, after a long period of use and you believe that the temperature reading displayed by the thermometer is not accurate, you may  follow the  process below to re-calibrate the thermometer:

1. Use distilled or purified water to make ice cubes in your refrigerator;
2. Get a thermally insulated bottle. If you don’t have one, use a beaker or a regular cup;
3. Fill the bottle with ice cubes (no less than 70% of the volume), then top off with cold distilled or purified water (no greater than 30% of the volume);
4. Stir the mixture and let it sit for 10 minutes to allow the ice and water to reach its temperature equilibration;
5. Turn on the thermometer, unscrew and take off the battery cover.
6. Immerse the probe in the ice/water mixture and make sure not to touch the sides of the container. Wait till the temperature reading drops to its lowest value, which should be around 32°F or 0°C. If the temperature of the ice/water mixture is not within 28°F to 36°F (or -2°C to +2°C), the calibration can’t be continued: you will need to follow  the above steps to re-make the ice/water mixture;
7. Press and hold the CAL button for 5 seconds to enter the Calibration mode. CAL will display for 3 seconds and the current temperature will display on the screen.
8. Press the CAL button once to confirm the calibration mode and exit the calibration mode.
   Note: The Calibration mode will only last for 15 seconds. If you’re unable to finish the calibration within 15 seconds, the thermometer will automatically exit Calibration mode.

UNDO-CALIBRATION

If you want to undo the calibration and go back to the default calibration setting, please follow the below steps:

1. Turn on the thermometer and press the “CAL” button 5 seconds to enter Calibration mode;
2. Press the lock button to undo the calibration and it will reset to the default setting.

HELPFUL HINTS

• When measuring different foods or meat, it may be desirable to cool the probe first by rinsing the tip with cold water.
• It is recommended that you wipe the probe tip clean between readings.
• This is especially important when taking temperature readings from different foods or meat.
• The thermometer is designed for temporary, handheld use. DO NOT use in an oven. DO NOT leave it in extremely hot foods or liquid (anything over 572°F) for more than 1 minute.
• Always take your reading in the thickest available portion of meat. Thin portions of meat are difficult to measure because they tend to cook through fast. Avoid touching a bone. If the tip touches the bone or heavy fat area of the meat, or if the tip is not deep enough, take a second reading to ensure accuracy.
• Not intended for use by persons under age 12.

CARE OF YOUR THERMOMETER

• Do not touch the stainless portion of the thermometer during or right after measuring temperatures since it will be very hot.
• Do not place the unit in dishwasher or immerse in any liquid. To clean, wipe the probe tip with a damp soapy cloth or sponge and then dry.
• Do not leave exposed to extremely high or low temperatures since this will damage electronic parts and plastics.
• Do not keep the thermometer inserted in food during cooking.
• Remove batteries if store for more than four months.

DECLARATION OF CONFORMITY

Hereby,
this product complies with the basic requirements and applicable complies with the basic requirements and applicable regulations of the EMC Directive 2014/30/EU. The  complete declaration of conformity can be found at: https://itronicsmall.com/eu-declaration-of-conformity/the manufacturer declares that

DISPOSAL

Meaning of the “Dustbin” Symbol

• Protect our environment: do not dispose of electrical equipment in domestic waste.
• Please return any electrical equipment longer use to the collection points provided for their disposal.
• This helps avoid the potential effects of incorrect disposal on the environment and human health.
• This will contribute to the recycling and utilization of electrical and electronic equipment.
• Information concerning where the equipment can be disposed of can be obtained from your local authority.
  CAUTION: rechargeable batteries must not be disposed of with household waste!
• The batteries must be removed from the appliance.
• Take spent batteries to the appropriate collection point or to a dealer.
• Your town or local authority can provide information about public collection points.

This symbol can be found on batteries/ rechargeable batteries which contain hazardous.

Pb = contains lead
Cd = contains cadmium
Hg = contains mercury
Li = contains lithium

 LIMITED ONE-YEAR WARRANTY

ThermoPro warrants this product to be free of defects in parts, materials and workmanship for a period of one year, from date of purchase.
REGISTER your product after purchase and RECEIVE EXTENDED 3 YEARS Warranty on our website: https://itronicsmall.com/pages/warrantyregistration
Should any repair or service under this warranty be required, please contact Customer Service by phone or email for instructions on how to pack and ship the product back to  ThermoPro. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

CUSTOMER SERVICE

Telephone: 1-877-515-7797(USA & Canada only)
Email: [email protected] 
Hours: Weekdays 8:00 AM- 8:00 PM
EST(USA & Canada only)
Weekdays
44-203-769-1321(UK)
1:00 PM – 12:00 PM
CET(UK)

ThermoPro Digital Laser Infrared Thermometer Instruction Manual

Introduction

Thank you for purchasing the ThermoPro TP30 Infrared Thermometer. This easy- to-use device lets you conveniently and accurately measure surface temperatures from a distance without the need of any direct contact.

Features & Specifications

• Laser guided targeting for better aiming precision
• Narrow distance-spot ratio for accurate results at long distances
• Safely measure hazardous or inaccessible objects
• Battery: 2*AAA batteries, 0V
• Measurement Range: -58°F-1 022°F (-50°C 550°C)
• Accuracy: *1.5&
• Resolution: 1°F or 0.1°C
• Wavelength: 5um-14um
• Distance-Spot Ratio: 12: 1
• Response Time: 500ms
• Emissivity: 10-1.00 (Default 0.95)
• Backlight: Auto-off after 15 seconds
• Auto-off: Auto-off after 90 seconds of inactivity
• Low battery Indicator

Function Diagram

1. SCAN: When pressing the measurement trigger, SCAN will appear on the
2. HOLD: When the measurement trigger. is released, HOLD will appear on the display
3. 1 Laser Pointer indication: When pressing the measurement trigger, a laser beam will appear to help guide you unless the laser is turned off.
4. Cui Low battery indication: Will appear on the display when battery power is low
5. UPPER DISPLAY: Displays the latest Temperature measurement.
6. EMISS: Press and hold the MODE button for 3 seconds, EMISS will appear, and you can adjust the emissivity setting
7. LOWER DISPLAY: Displays MAX/MIN/ AVG temperature; When adjusting the Emissivity setting, the current emissivity setting will be displayed
8. MAX/MIN: Maximum and minimum temperature for the latest measurement
9. AVG: Average temperature for the latest measurement
10. Press once to turn on/off Laser Pointer; Press and hold for 3 seconds, to switch between °C and °F; When adjusting the emissivity, press to lower the emissivity
11. Press to cycle through and display MAX/MIN/AVG temperature; Press and hold for 3 seconds, to adjust the emissivity setting
12. Press to turn on/off the backlight; When adjusting the emissivity, press to increase the emissivity
    
13. Laser Hole
14. IR Sensor
15. Measurement Trigger: Hold and release to take temperature
16. Battery Compartment
    

    

Operation

Surface Temperature Measurement NOTE: The ThermoPro TP30 cannot measure the temperature of objects Behind glass. Inaccuracy may also Occur when exposed to steam, dust or any other contaminants in the air.

1. Place the included AAA batteries into the Battery Compartment, then press the Measurement Trigger lo activate the thermometer
   
2. Point the TP30 thermometer towards the surface you wish to
3. Press and hold the Measurement Trigger and the laser will activate for aiming (Laser will only appear if enabled. Laser is turned on by default.)
4. Keep holding the Measurement Trigger as you move the TP30 if you wish to continually take a measurement of the surface
5. Once the laser is pointed to the desired point of measurement, release the Measurement Trigger and the Upper Display will show the last measured temperature
6. Press the Measurement Trigger once again to make another measurement

• HOLD for continuous temperature
  
  
• RELEASE to lock the temperature result
  
  

Emissivity

The emissivity of a material is its efficiency in emitting thermal energy. Non-reflective surfaces have a higher emissivity (closer to 1) than reflective surfaces (closer to 0). Inaccurate results may occur when measuring reflective surfaces such as glass, polished wood, and granite. To take accurate temperature measurement of reflective surfaces with low emissivity, place a strip of masking tape over the surface and allow for it to adjust to the temperature of the surface for approximately 30 minutes. Measure the surface, scanning the taped section, eliminating the issue of inaccuracy.

The default emissivity of this device is 0.95, which is suitable for surface temperature measurement of most organic materials and painted objects. If you would like to improve the measurement accuracy of different objects, you can refer to the emissivity table below :

Distance-Spot Ratio

The ThermoPro TP30 measures surface temperature base dontheis{anceto spot diameter ratio (D: S). As the distance between the thermometer and the surface increases, the total surface area measured will also increase. With a distance to spot ratio of 12:J, the surface area measured has a diameter of roughly 1/J 2 the distance.

For the most accurate results, make sure the target has a surface area of twice the corresponding spot diameter. Insufficient surface area will result in inaccurate results. The recommended distance to hold the thermometer from the surface of measurement is 7.87inch (20cm) away from the surface. This creates a spot measurement area of 0.6óinch(J.67cm) in diameter.

Distance (D) to Spot (S) size D:S=12:1

Replacing Batteries

Low Battery Indication will appear on the Upper Display when the thermometer’s batteries are running low. Immediately replace the batteries when the icon appears.

1. Open the Battery Compartment and remove the used batteries. Dispose of the used batteries
2. Insert two new AAA batteries with the correct
3. Close the Battery Compartment
   

The device certification information is labeled directly on the device. The sticker is located on the left side of the thermometer The device warning and aperture safety information are also labeled directly on the device; this sticker is located on the right side of the thermometer.

Package Contents

• 1x ThermoPro TP30 Infrared Thermometer
• 2x AAA batteries
• 1x User Manual

Safe Use & Care

• D0 NOT point the laser beam at another person or
• D0 NOT attempt to point laser beam at an
• Avoid direct/indirect eye contact with the laser-beam. Laser radiation may cause eye
• D0 N0T view the beam with optical
• If using near bystanders, make them aware of the dangers of looking directly into the laser beam
• DO NOT allow children to operate the device
• Use two 1.SV AAA batteries when replacing the batteries within the device
• Make sure to inset the batteries in Accordance with the correct polarities
• ALWAYS remove the battery when cleaning the device
• DO NOT use leaking battery of dispose of old batteries in fire
• Remove the batteries if storing the device for a prolonged period of time.
• DO NOT disassemble the device or tamper with internal components. Doing so will void any warranty
• D0 NOT touch the lens or wipe it using anything other than a soft cloth or cotton swab
• Keep the thermometer away from electromagnetic fields produced by  objects such as arc welders and induction heaters
• DO NOT expose the thermometer to direct sources of heat for extended  period of time
• The thermometer measures surface temperature, not internal temperature Do not use it as a reliable source to  measure body temperatures

Disposal

Meaning of the “Dustbin“ symbol

• Protect our environment: do not dispose of electrical equipment in the domestic waste
• Please return any electrical equipment that you will no longer use to the collection points provided for their disposal
• This helps avoid the potential effect  of incorrect disposal on the environment and human health.
• This will contribute to the recycling and other forms of reutilization of electrical and electronic equipment
• Information concerning where the equipment can be disposed of can be obtained from your local authority
  CAUTION : Batteries/rechargeable batteries must not be disposed of with household waste!
• The batteries must be removed from the appliance.
• Take spent batteries to the appropriate
• Your town or local authority can provide information about public collection points

This symbol can be found on batteries/ rechargeable batteries which contain hazardous :

• Pb = contains lead
• Cd = contains cadmium
• Hg = contains mercury
• Li = contains lithium

Limited one-year warranty

ThermoPro warrants this product to be free of defects in parts, materials and workmanship for a period of one year, from date of purchase. Should any repairs or servicing under this warranty be required contact Customer Service by phone or email for instructions on how to pack and ship the product to ThermoPro.

This warranty gives you specific legal rights and you may also have other rights which Vary from state to state

Customer service

Telephone: 1-877-515-7797(USA & Canada only) 44-203-769-1321 (UK)
Email: [email protected]
Hours: Weekdays 8:00 AM- 8:00 PM EST (USA & Canada only) Weekdays 1:00 PM – J2:00 PM CET(UK)