Smart Watch ID205L

Smart Watch ID205L

Thank you for purchasing our products. This manual addresses the safety guidelines, warranty, and operating instructions. Please review this manual thoroughly before operating your device.

Getting Started

What’s in the box

What’s in this document

This manual gets you started quickly with setting up your watch. Setup ensures that your watch can synchronize its data with the VeryFitPro app, where you can get detailed information on your stats, view historical trends, log sleep, and more. As soon as setup is complete, you’re ready to start moving. The remainder of the manual walks you through every function on your ID205L.

Setting up Your Watch

Charging your watch

Please fully charge your watch before initial use.

1. Insert the USB plug of the charging cable into the USB port on your computer or a UL-certified USB wall charger.
2. Hold the other end of the charging cable near the port on the back of the watch until it attaches magnetically.
3. Make sure the pins on the charging cable lock securely with the port. The connection is secure when the watch vibrates and the battery icon with percent charged appears on the screen.

When the watch shows that the battery is low, connect the watch to a USB port with 5V-500mA.

While the watch charges, there is a battery progress bar on the screen and you can press the function button to check the battery level.

Remove the watch from the power supply once fully charged.

• USB charger requirement: DC USB port (5V-500mA)
• Charging time: 2-3 hour”

Disassembling / Assembling Your Watch

Disassembly

1. To remove the wristbands, turn over the watch and find the quick-release lever.
2. While pressing the quick-release lever inward, gently pull the wristband away from the watch to release it.
3. Repeat on the other side.

Assembly

1. To reattach the wristbands, slide the pin (the side opposite the quick-release lever) into the notch on the watch. Attach the wristband with the clasp to the top of the watch.
2. While pressing the quick-release lever inward, slide the other end of the wristband into place.
3. When both ends of the pin are inserted, release the quick-release lever

Wearing Your Watch

All-day wear and exercise

For all-day wear when you’re not exercising, wear the device on your wrist horizontally, a finger’s width below your wrist bone and lying flat, the same way you would put on a watch.

For optimized heart rate tracking, keep these tip” in mind:

1. Experiment with wearing the watch higher on your wrist during exercise. Because the blood flow in your arm increases the farther up you go, moving the watch up a couple of inches can improve the heart rate signal. Also, many exercises such as bike riding or weight lifting require you to bend your wrist frequently, which is more likely to interfere with the heart rate signal if the watch is lower on your wrist.
2. Do not wear your watch too tight. A tight band restricts blood flow, potentially affecting the heart rate signal. This being said, the watch should also be slightly tighter (snug but not constricting) during exercise than during all-day wear.

Using Your Watch

App Installation

Use the watch with our customized VeryFitPro app. You can download VeryFitPro from Apple Store/Google Play or scan the QR codes below to download.

iOS

Android

Notes:

• The VeryFitPro app is only compatible with smartphones, not tablets or PCs.
• Smartphone operating system should be iOS 8.0 / Android 4.4 or higher; Bluetooth version should be 4.0 or higher.

Smart Phone System Requirements

• iOS 8.0 & higher
• Android 4.4 & higher
• Bluetooth 4.0 & higher

App Interfaces

Please pair the watch with your phone in the VeryFitPro app, NOT in the Bluetooth settings of your phone.

1. Enable the Bluetooth of your smartphone.
2. Open the VeryFitPro app on your smartphone and go to the “Device” page, tap “Bind Device”, then your smartphone starts searching devices.
3. In the list of found devices that appear on your smartphone, tap on “ID205L” to connect the watch to your smartphone. (If your phone failed to find ID205L, please search the watch on your smartphone again.)

Notes:

• Once the watch is connected to your app, the watch will automatically search and reconnect itself if the connection is lost or when Bluetooth is restarted after manual disconnection.
• If the watch is unbound from the app’ the information on the watch will be reset, and the information on the app will be cleared. Please do not unbind the connection unless there is an issue that will require a reset.
• The watch can only pair with one smartphone at a time. When pairing, please ensure the watch and your smartphone is within 0.5 meters distance.

Getting to Know Your Watch

Function Button

• Press the function button to wake the screen or return to the previous interface.
• Press and hold the function button to turn on the watch.

Watch Interfaces

This is a touch screen; swipe the screen to go to different interfaces, and tap to enter the function.

The home screen is the clock. On the clock:

• Swipe down to see notifications.
• Swipe up to see your daily stats.
• Swipe left to see the function  list.
• Swipe right to see the status bar.

After the watch is bound to the app, the home screen will display the time and date as shown in fig. 1.

You can customize the home screen by following the steps below:

1. Tap and hold the home screen.
2. Swipe down to choose one and tap to confirm.

Wake a Dimmed Screen

To conserve power, the watch has a standby mode in which the screen turns off. To wake the screen, turn your wrist towards you or press the function button.

Function Introduction

1. Tracking Sports

The watch tracks your exercise data in up to 9 sports modes. You can set up to 8 different sports modes from among 9 sports modes in the app to display on the watch screen ( “Device” page → “More” → “Activity display” ).

Start a sport
Tap “Sport” → Swipe the screen to view “port” mode” → Tap the sport you choose to start.

During sports

• Swipe the screen left/right to flip through exercise data.
• Press the right key to pause/resume the sport.

End the sport
Press and hold the right button to end the sport → Tap “√” to confirm.
Exercise data is displayed after the exercise has ended. Swipe down the screen to flip through exercise data:

Data of exercises less than 1 minute will not be saved.

Notes:

• You can also use your phone’s GPS to track your pace and distance during walks, hikes, runs or rides while mapping out your run or walk on your phone.
  In the app, tap and will pop up. Tap to enter running mode directly or tap to choose another sports mode. After entering running mode, the app will track and map your run distance (using your phone’s GPS). After the exercise, you can effortlessly check your exercise data in both the app and the watch.
• Sports mode is up to 6 hours.

2. Monitoring Heart Rate

The watch tracks your real-time heart rate automatically and continuously. You can also view your detailed heart rate data on the watch screen or in the app.

Notes:

• To monitor heart rate more accurately’ wear the watch on the upper position of your wrist and a bit tighter than usual when you exercise. In addition, complete your profile in the app.
• Automatic heart rate monitoring i” 9N by default’ monitoring heart rate all day automatically. You can disable/enable automatic heart rate monitoring on the watch (swipe the watch screen right to come to the status bar), or in the app (“Device” page ► “Heart Rate Detection”).

3. Relaxing

Tap to start the relaxing ► Press the right button to end the relaxing ► Tap “√” to confirm

4. Setting Alarms

1. Go to the “Device” page in the app and tap “Alarm Alert”.
2. Tap “+” to add an alarm.
3. Tap the alarm, then set the alarm type, repeat type and time.
4. Tap “√” to save your settings.

You can tap the alarm you set on the watch screen to enable / disable the alarm.

5. Controlling Phone Music

1. Go to the “Device” page in the app and tap “Music Control”.
2. Enable the function and tap “√” to save your settings.
3. Tap “Music Controller” on the watch screen to enter the function and control the music playing on your phone.

Note:
You can only control the music player that’s running on your smartphone.

6. Tracking Sleep

The watch automatically tracks your sleep duration (Deep Sleep, Light Sleep, and Wake-sleep) and consistency with a comprehensive analysis of sleep quality data so you can see your sleep trends and improve your routine. You can check your detailed sleep data in the app.

7. More Functions

Call Notification

When there is an incoming call, the watch vibrates to alert you, and the screen displays the caller ID.

Tap on the watch screen to reject the call.

Notes:

• 9nly when “Call alerts is enabled in the app (“Device” page ► “Call Alert”) will calls be (After enabling/disabling the Call Alert function’ tap “√” to save your settings.)
• When “Do not disturb” is enabled in the app (“Device” page ► “More” ► “Do not disturb”)’ call” will not be notified on the watch during the do-not-disturb

Message Notification

When messages (SMS, Facebook, WhatsApp, Twitter, Instagram, Facebook Messenger, LinkedIn, Email, Mail, Calendar, and more) come in, the watch vibrates to alert you, and the screen displays the message content.

Notes:

• 9nly when “SNS Alerts is enabled in the app (“Device” page ►”SNS Alert” ► “Allow notification”), will messages be notified. (After enabling/disabling the SNS Alert function, tap “√” to save your settings.)
• When the “Do not disturb” function is enabled in the app (“Device” page ► “More” ► “Do not disturb”) or on the watch (Status bar ► ““), message” will not be notified on the watch during the do-not-disturb period.

Sedentary Reminder

The watch vibrates to remind you to get up and move around when you have been sitting too long (“Device” page ► “Sedentary Alert”, enable the Sedentary Alert function and set the remind interval.)

Find Phone

You can use the watch to locate your phone by making your phone vibrate or ring when the distance between your phone and the watch is within 10 meters (33 feet).

1. Go to “Device” page ► “More” ► “Find phone” in the app and enable the function.
2. Swipe the watch screen right to come to the status bar and tap “” to use the function.

Note:
You can use the find phone function only when it is enabled in the app.

Basic Specifications

Electronic Information Products

Toxic and Hazardous Substances Statement

This product meets the EU ROHS standards
Refer to IEC 62321 and EU RoHS
Directive 2011/65 / EU and its revision instructions

FAQs

Failure to find the watch when pairing

1. Make sure your smartphone’s Bluetooth is enabled and your smartphone’s system meets the requirements of Android 4.4 or higher, iOS 8.0 or higher, and Bluetooth 0 or higher.
2. Make sure the distance between your smartphone and the watch does not exceed 0.5 meters and that Bluetooth communication is also within range (10 meters max).
3. Make sure your watch has enough battery life. If there is still a problem after being fully charged, please contact us.

Occasional failure to connect with Bluetooth

Reboot your smartphone or restart your smartphone’s Bluetooth.

Failure to receive SMS/calls notifications

Calls/SMS notification function works when the watch connects to your smartphone via the app. Please kindly refer to the following tips:

1. Go to your smartphone Settings, find VeryFitPro app and enable the Location and all Notifications.
2. Enable your phone’s Bluetooth and go to the VeryFitPro app to bind the watch.
3. Enable the Call/SNS Alert function’ and tap “√” to save your settings.

Failure to connect to smartphone

The watch will disconnect from your smartphone in the following cases:

1. Smartphone Bluetooth is off or exceeds the Bluetooth connection range (the maximum Bluetooth connection range is 10 meters and can easily be reduced by walls, furniture, etc.)
2. The VeryFitPro app is closed on the phone. (This can occur automatically under certain circumstances.)

To reconnect the watch to your smartphone, please kindly take the following steps:

1. Go to your smartphone system Settings, find the VeryFitPro app and enable the Location and all Notifications.
2. Clear all running / background processes on your smartphone. Go to the VeryFitPro app and swipe down “Main page”, then the watch will reconnect to your smartphone and update data. You can also restart your smartphone and Bluetooth, then rebind the watch in the app.

Smart Watch ID205L User Manual – Optimized PDF
Smart Watch ID205L User Manual – Original PDF

FAQ’S

What if the watch doesn’t charge?

Make sure you have the latest firmware installed. If you still can’t get your watch to charge, contact our customer service team at [email protected].

How long does it take to fully charge?

It takes about 2 hours to fully charge. You can check the battery level in the app or on the watch.

How do I use smart watch ID205L?

Enable the Bluetooth of your smartphone. Open the VeryFitPro app on your smartphone and go to the “Device” page, tap “Bind Device”, then your smartphone starts searching devices. In the list of found devices that appear on your smartphone, tap on “ID205L” to connect the watch to your smartphone.

Can I answer call with ID205L?

The device has a speaker and microphone that allow you to answer calls made to your smartphone

Does ID205L have GPS?

The app does sort of act as a fitness/tracking app—it has overviews of your activity, sleep, and heart rate data—but you can’t manually enter in data (you can start activities, such as GPS-connected workouts, from the app, but you can’t log them after the fact).

How do you call someone on a smart watch?

Make a call
Tap your watch’s screen to wake your watch up.
Say “Ok, Google. Make a phone call.”
Say a contact’s name or speak the numbers you’d like to call.
To end the call, tap Hang Up .

Is the VeryFitPro ID205L waterproof?

Pro-Fit Move VeryFitPro Smart Watch HR Heart Rate Sleep Monitor IP68 Waterproof Activity Fitness Tracker Step Counter Pedometer Exercise Running Watch Fitness Watches for Men & Women (ID205L) (Pink)

What Bluetooth device is ID205L?

Bluetooth ID205L HD Screen Smart Watch Wearable Tracker Heart Rate Sports Waterproof 1.3 Inch for Android Ios Smart Watch.

How do I reset my VeryFitPro watch?

Performing a reboot will reset the device and should resolve any issues.
Open the VeryFitPro app.
Tap User.
Tap System Setting.
Tap Restart Device

How do I set the time on my VeryFitPro ID205L?

Set your watch’s time and date
If the screen is dim, tap it to wake up the watch.
Swipe down from the top of the screen.
Tap Settings . If you don’t find it straight away, swipe left.
Tap System Date and time. Choose your time settings.

How do I connect my smartwatch to my Android phone?

Pairing an Android Wear smartwatch with an Android phone
Install the “Wear OS by Google Smartwatch” app on your phone, available on the Google Play Store. On your watch, turn on Bluetooth. Open the Wear OS app on your phone and follow the initial setup. Tap on “I agree”.

Why is my watch not pairing?

If you’re having issues connecting your watch and phone, please begin by making sure that your phone’s OS version is compatible (Android 6.0+ and iOS 10.0+) and that the Wear OS by Google app is up-to-date. Then, check if you have activated Bluetooth on your phone, disable, and re-enable it.

VIDEO

Smart Watch ID205L

Smart watch U8

User Manual

Thank you for choosing our sport healthy intelligent Bluetooth watch. You can read this manual and fully understand how to use the device, with a good experience of the functions and easy operation. This equipment is mainly used brand of smart phones to be adapted to use, you can synchronize the phone book smart phones and provides a variety of useful features and services to facilitate your work and leisure activities in the smart phones operation. This device has the following features: support for Bluetooth phone. Bluetooth message push (SMS, short message, QQ, etc., Need a installation of Bluetooth notification APK on Android smart phone), Bluetooth music player, calories, pedometer, sleep monitoring, antilost, remote camera and so on.

Before you start using this device, please install ‘BT notice’ APK on your smart phone through scanning the QR code on the right, (support Android version, Apple does not currently supported) and run, the smart watch can display the notification/reminders of the application from the Bluetooth connected smart phone synchronously via ‘message’ and ‘distal notice’, including SMS alerts, chat tool QQ, micro letters and other messages and reminders.

To use the ‘notice’ function, need to open ‘BT notice’ on the smart phone. Restart the phone and smart watches, you can use the Bluetooth connection. Scan the QR code to install ‘BT notice’ application, or visit the following link to download installation package by scanning:

http: //pan.baidu.com/s/lhqsuR7A, search ‘Bluetooth notice’ at Google Play APP store to download and install it. By registering overseas can log on Google Play, then scan the QR code, or visit the link to download the APK.

https://play.google.com/store/apps/details?id=com.oinom.btnotification&hl=zh-CN

The company reserves the right without prior notice to the contents of the manual to make changes.
(1)How to wear and operate.

Wear this Bluetooth smart watch in the correct direction, the power button should be on the right of the watch, three touch buttons located beneath the LCD.

– On/off button, exit buttons: 1) Turn on the watch: press the on/off button power for 2 seconds, the watch shows main interface. 2) Turn off the light: press the on/off button shortly. 3) Turn on the clock: press the on/off button at the third time, the watch shows the clock.Touch keys at lower left corner, Menu/Enter key: Press the Menu/Enter key when the watch is on standby clock interface, to enter main menu interface.

– Middle touch key, dial into/flip key: 1) Press this button when the watch is on main menu interface, to enter dial interface. menu operation as the next flip key, 2) Press dial into/flip key to adjust the volume when playing music and making calls.

– Lower right corner of the touch keys, return/hang up button: standby no effect, like the return menu operation keys, call hang up button.

In addition, Sliding fingers to touch the screen can achieve the following functions:
– Slide you finger around the touch screen: menu page.
– Finger tap the touch screen: enter the menu.
– Finger down from the top of the screen vertical stroke: Exit menu.
Connect to Bluetooth devices, disconnection and continuous connection

There are 2 ways to realize the Bluetooth connection: 1) the watch rise up a Bluetooth connection requirement, 2) the smart phone rise up a Bluetooth connection requirement After a successful connection of Bluetooth, Smart Watch will automatically send a request requires reading smart phone phonebook and call log (involving personal privacy, some smart phone do not turn on this feature) Please confirm the smart phone, or else the watch can not be synchronized to the phone book and call history will affect its normal use.

If the distance between the watch and smart phones is more than 10 meters (there should not be any obstructions, or it might shorten the strength of the signal) they will be automatically disconnected, if the distance can be recover to 10 meters less again within 5 minutes, the connection could be recovered automatically. Both of the watch and smart phone will alarm when disconnection happens.

Features
Bluetooth, search for Bluetooth devices, connection, disconnection and other operations.
– Dialing Press this button when the watch is on main menu interface, to enter dial interface, or dial numbers though ‘call log’ menu.
* Do not block the speaker or microphone position during a call.
– Information Read the short message from the connected smart
phone synchronously
– Phone book synchronization of the phone book.
– Call log Synchronize phone call records of the “missed call”,
“Dialed”, “Received Calls”, “All records”, Maximum 30 records.
– Bluetooth notification Can view the push notifications of
applications like QQ, short messages from connected smart phone.
– Bluetooth music can play music on your smart phone via Bluetooth.
Some smart phones will need to open the music player software to run properly. Press dial into/flip key to adjust the volume of music, Or directly touch the “+”,”-“ buttons on the screen. The watch will return to the initial interface after stopping pressing the key or screen, no need to press exit key manually.
– Remote camera control via Bluetooth smart phone camera to take the pictures.
* The smart phone should not be on the status of screen locking, or this function won’t work properly
– Pedometer
Pedometer designed specifically for health caring customers, to ensure the accuracy of the steps counting, we recommend the user to walk normally with a head and chest rising posture.

On the top of the pedometer displays time counting, on the left is steps counting, the distances (meters) is showing on the right, the consumption of calories is on the bottom. To start/stop the

counting by using the button in the middle. On the right above the screen is settings, it can adjust the parameters, reset or view the records. The pedometer can run in the background.

To avoid false count, the watch will not show up the numbers immediately after taking the initial steps for each user, but it starts to display after a stable walk counting, the number of previous steps is counted already.

* The Pedometer will clear the record of steps at one time everyday, then restart counting and accumulating till next time clearance. User can also clear the record by ‘reset’ button in the option menu.
– Anti-lost alarm When the connected smart phone is far away from watch over a certain distance. The watch will sound an alarm.
– Power saving mode
– Settings the clock setting, The tone mode, volume, language, display settings, view battery power, as well as Bluetooth settings and restore the factory settings.
(4) Bluetooth smart watch can connect to a standard USB data cable.
To charge be battery through computer USB port or USB power
bank.

Note: To reset the watch to default settings, please key in the initial
password “1122”.

FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device is measured RF output power is less than the SAR exclusion threshold value for human head and body. Therefore, SAR test is not necessary.

Frequently Asked Questions

1.unable to search bound hand ring or can not connect,Make sure that the Bluetootll phone is turned on and dose to file bra- celet, restart the phone application or Bluetooth connection with the search and try pairing again. Also, make sure your phone system is Android 4.4 or more, 108 8.0 or more, the phone supports Bluetooth 4.0 and Bluetooth connectivity is stable. (Make sure your phone paired Bluetooth devices not too much)

2.APP no data appearing The bracdet using manual switch the measurement or timing measurements. At first use only basic movement data (step cormter, distance, calories). With continuous use, the bracelet by a single measurement of APP appD- canon, real-Ume measurement, a key measurement di- splay data.

3.Tlle time is not accurate bracelet When the bracdet is dead, re-charging, wristbands time error may occur, connect the phone, the phone will au- tomatically synchronize bracelet time calibration.

4. The bracelet can not charge or use a short time Please use the product with the aligning char ging clip bracelet back of file main contact s, note the alignment and do not constanUy have to grip the friction caused by the shift of the charge after charge is bad. The first time you use the product, please complete the charging power consumption for the first time atter 1- 1.5 hours. Make sure the battery is fully remain in me- mory function and memory status.

5. Can not download or upgrade the hardware upgrade is interrupted. In adopting the hardware upgrade (OTA) Make sure that the bracelet is fully charged and the mobile phone net- work in stable condition.

Please refer to claim 3 connecffon uses precautions to ensure mobile application APP phone supports all the features.

6. Basic parameters
Screen size: OLED 0.86 inches
Bluetooth: BT 4.0
Battery capacity: 85Mah
Bracelet Dimensions: 46.7mm * 19.7mm * 11 .2mm
Strap size: 200mm * 16. Imm * 2.2mm
Material: PC + TPU Waterproof Levd; IP67
Packing list: Host bracelet, Wrist strap, charging cable, manual K The company reserves the right to modify the contents of this manual without prior notice, some of the features are diff erent in the corresponding version of the software are normal conditions

Warning
Please follow medical advice, take measurement results as self-diagnosis and treatment basis is very dangerous. Users with blood circulation disorders, blood pressure disease pleasetake the treatment under the guidance of a doctor~ product measurements are for reference only, and not for any medical use basis.

Intelligent Blood Pressure Blood Oxygen Heart Rate Bracelet Appearance

1. adapted platforms and requirements

Android 4.4 or Above

IOS 8.0 or Above (Does not include Apple 4)

Phone hardware support Blutooth 4.0 ( Blutooth Connection Stable)

2. Preparations
First tirne use, PIS ensure battery is fully charged . If not turn on due to low battery, please use the charging clip Align with the contacts of the bracelet main back chatging for 1-1.5 hours (first use make sure the battery is full), the bracelet will indicate charging flag and display the charging status. After charging is complete, press and hold the button 5-8 seconds to boot.

3. Connection uses
In normal use conditions, bracelet needs to be connected with the mobile application. be sure to use a mobile phone to meet the above requirements and adap ted platform device hardware requirements, tociownlmd the corresponding phone APP.

Matters needing attention:

Android phones: Settings – Accessibility – All functions supported / background operation

Settings – Applications -Wearfit- supports the use of all the features
IPhone: Settings – General – Device Management – Software Trust Setting -Wearfit- allows the use of function

Mobile application language swltdwing according to the phone language Blndlng uses:

After downloading the software, please ensure the phone bluetooth is turned on, open the “Wea rfit”, the first use needs to bind the connection, click binds the bracelet, select the device appeared in the Bluetooth list, click to connect the binding and pairing successfully, will enter the Main interface of mobile phone application.

4. Precautions:

After the bracelet and mobile applications successful binding, the phone will synchronize the time and date, and start recording and analysis of movement, heart rate, blood pressure and sleep.

Bracelet: Click the button to switch wristbands interface

Bracelet function list is as follows

1. Time mode: time, date, batteiy, Bluetooth connection status display

2. Movement recording: automatically record movement data on foot every day.

3. Distance mode: automatically records walking distance every day.

4. Calories modes: automatic calories data recording per day.

5. Heart rate mode: current heart rate data monitoring, switch the key to heart rate interface, measurement mode will open. if not, please continue switching, bracelet appears as the most recent measurement data. Mobile applications display data by a single measurement, rea1—t1me measurement or a key measurement. (NOT E: Press the switch button to change interface, measurement data can not be synchronized to the phone application. HR interface, pls let the skin wrist above be close to the bracelet to prevent light leakage.)

6.Blood Oxygen mode: current blood pressure monitoring, switch the key to the blood pressure interface, lneasureuient iuode will open, if not, please continue switching, bracelet appears as the most recent nlcasurcincrit data. Mobile applications display data by a single measurement, real—tirne measurement or a key measurement. (NOTE: Press the switch button to change interface, measurement data can not be synchronized to the phone application. HR intertace, pls let the skin wrist above be close to the bracelet to prevent light leakage.

7. Blood Pressure mode: current blood pressure monitoring, switch the key to the blood pressure interface, measurement mode will open, if not, please continue switching, bracelet appears as the most recent measurement data. Mobile applications display data by A single measurement, real-time measurement or 1: key measurement. (NOTE: Press the switch button to change interface, mcaaurcnicnt data can not be synchronized to the phone application. HR interface, pls let the skin wrist above be close to the bracelet to prevent light leakage.)

8.Sleep mode: automatic monitoring of the quality and status of sleep every day.

9. Powered Off: Long press the button to enter the shutdown interface, long press the button to choose whether to switch off.

10..Ca.lls reminder: mobile application APP open the function of calls to reminds, click the top left corner to enter the mobile phone APP management interface ~ Device Managernent — Intelligent Reminder — selector switch. When phone calls wristband will vibrate and remind.

1 1.SMS / Applications reminder: mobile application APP open the switch of SMS alerts / reminders, click the top left corner to enter the mobile phone APP management interface – Device Management – Intelligent Reminder – selecting switch.

HR Tips

1.Most people has the heart rate of about 60- 120.

2.Most people resting heart rate is 60 to 90 beats / minute, the optimal heart rate is up to 70 beats / minute.

3.The heart rate of athletes and trained people is 40 to 60 beats / minute.

4.1-Ieart rate is always been changing, and after (§{€IC.lSC, after eating, personal circumstances factors, good or bad mood, etc., are heart rate constantly changing factors.

5.When doing Aerobic exercise to an ettective and safe condition,people’s heart rate is 170, minus age, people should hold the heart rate between 1O8 to 144.

6.Pleaee Exercise regularly, proper diet, weight control, psychological adjustment, to make themselves more healthy and happy every day.

Blood Oxygen Tips

1.0xygen saturation is the the percentage of oxygen- bound oxyhemoglobin (HbO2) capacity vs total hem-
oglobin (Hb) combined capacity, that is the concentr-ation of oxygen in the blood.

Blood Pressure Tips

1. Systo1ic blood pressure, arterial blood delivered to the highest value when referred to as “high pressure”, the heart for the next time the lowest blood pressure value reserve dilate when blood is called “low—voltage”, are referred to as systolic and diastolic blood pressure. 2.Most people has the heart rate of i8O blood pressure (low pressure) to 120 (high pressure) around.

3. Within the normal range, blood pressure has differentiation of age, gender. Generally, the elderly have the higher blood pressure than the young, men have the high blood pressure than women.

4. Blood pressure is always been changing, and after e xercise, after eating, personal circumstances factors, good or bad mood, etc., are heart rate constantly changing factors.

5. Please Exercise regularly, proper diet, weight control, psychological adjustment, to make themselves more healthy and happy every day.

This equipment has been tested and found to comply with the limits for a Class 3 digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. i his equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause hannful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause hannful interference to radio or television reception. which can be detennlned by tumlng the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Fteorient or relocate the receiving antenna.
– increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different lrom that to which the receiver is connected. — Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(I) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.

Questions about your M2 Smart Bracelet User Manual Post in the comments!
M2 Smart Bracelet User Manual [PDF]

References

• User Manual

M2 Smart Watch Manual

Intelligent Blood Pressure, Blood Oxygen, Heart Rate and Hand Ring Product Specification.

Frequently Asked Questions
1. unable to search
bound hand ring or can not connect, Make sure that the Bluetooth phone is turned on and close to the bracelet, restart the phone application or Bluetooth connection with the search and try pairing again. Also make sure your phone system is Android 4.4 or more, 105 8.0 or more, the phone supports Bluetooth 4.0 and Bluetooth connectivity is stable. (Make sure your phone paired Bluetooth devices not too much)

2. APP no data appearing
The bracelet using manual switch the measurement or timing measurements. At first use only basic movement data (step counter, distance, calories). With continuous use, the bracelet by a single measurement of APP appli-cation, real-time measurement, a key measurement di-splay data.

3.The nine is nut accurate bracelet
When the bracelet is dead, re-charging, wristbands time error may occur, connect the phone, the phone will automatically synchronize bracelet time calibration.

4. The bracelet can not charge or use a short time
Please nee the product With the aligning charging clip bracelet back of the main contacts, note the alignment and do not constantly have to grip the friction caused by the shift of the charge after charge is bad. The first time you use the product, please complete the charging power consumption for the that time after 1-1.5 hours. Make sure the battery is fully remain in memory function and memory status.

5. Can not download or upgrade the hardware upgrade is interrupted.
In adopting the hardware upgrade (OTA) Make sure that the bracelet is fully charged and the mobile phone net-work in stable condition. Please refer to claim 3 connection uses precautions to ensure mobile application APP phone supports all the features.

6. Basic parameters
Screen size: OLED 0.86 inches
Bluetooth: BT 4.0
Battery capacity: 8SMah
Bracelet Dimensions: 46.7mm ” 19.7mm ” 11.2mm
Strap size: 200mm ” 16.1mm * 2.2mm
Material: PC + TPU Waterproof
Level: IP67 Packing
list: Host bracelet, wrist strap, charging cable, manual

The company reserves the right to modify the contents of this manual without prior notice, some of the features are different in the corresponding version of the software are normal conditions

Warning
Please follow medical advice, take measurement results as self-diagnosis and treatment basis is very dangerous. Users with blood circulation disorders, blood-pressure disease please take the treatment under the guidance of a doctor, product measurements are for reference only, and not for any medical use basis,

1. Adapted platforms and requirements

* Android 4.4 or above
* IOS 8.0 or above(does not include Apple 4)
* Phone hardware supports Bluetooth 4.0(Bluetooth connection remains stable)

2. Preparations
First time use, pls ensure battery is hilly charged. If not turn on due to low battery, please use the charging clip Align with the contacts of the bracelet main back charging for 1-1.5 hours (first use make our the battery is full), the bracelet will indicate charging flag and display the charging status. After charging is complete, press and hold the button 5-8 seconds to boot.

3. Connection uses
In normal use conditions, bracelet needs to be connected with the mobile application. be sure to use a mobile phone to meet the above requirements and adapted platform device hardware requirements,to download the corresponding phone APP.

IOS Version Download

Android Version Download

Matters needing attention: Android phones: Settings -Accessibility- All functions supported / background operation Settings – Applications -Wear fit- supports the use of all the features [Phone: Settings -General – Device Management- Software Trust Setting -Wear fit- allows the use of function Mobile application language switching according to the phone language Binding uses: After downloading the software, please ensure the phone Bluetooth is turned on, open the “Wear fit”, the first use needs to bind the connection, click binds the bracelet, select the device appeared in the Bluetooth list, click to connect the binding and pairing successfully, will enter the Main interface of mobile phone application.

4. Precautions: After the bracelet and mobile applications successful binding, the phone will synchronize the time and date, and start recording and analysis of movement, heart rate, blood pressure and sleep.
Bracelet: Click the button to switch wristbands interface Bracelet function list is as follows

1. Time mode: time, date, battery, Bluetooth connection status display.

2. Movement recording: automatically record movement data on foot every day.

3. Distance mode: automatically records walking distance every day

4. Calories modes: automatic calories data recor-ding per day.

5. Heart rate mode: current heart rate data monitoring, switch the key to heart rate interface, measurement mode will open. if not, please continue switching, bracelet appears as the most recent measurement data. Mobile applications display data by a single measurement, real-time measurement or a key measurement. (NOTE: Press the switch button to change interface, measurement data can not be synchronized to the phone application. HR interface, pls let the skin wrist above be close to the bracelet to prevent light leakage.)

6. Blood Oxygen mode: current blood pressure monitoring, switch the key to the blood pressure interface, measurement mode will open, if not, please continue switching, bracelet appears aa the most recent measurement data. applications display data by a single measurement, real-Prue measurement or a key measurement. (NOTE: Press the switch button to change • interface t d ta can not be synchronized the phone HR interface, pls let the skin wrist above be close to the bracelet to prevent tight leakage.

7. Blood Pressure mode: current blood Pressure monitoring switch the tie, to blood pressure interface, measurement mode will open, if not, please continue switching, bracelet appears as the most recent measurement data. Mob. applications display data by a single measurement, real-lime measurement or a key measurement (NOTE: Press the match button to change interface, measurement data can not he to to the phone application. 110 interface phi let the skin wrist shove be close to the bracelet to prevent tight leakage.)

8. Sleep mode: automatic monitoring of the quality and status of sleep every day

9. Powered Off: Long press the button to enter the shutdown interface, long press the button to choose whether to switch off.

10. Calls reminder: mobile application APP open the function of calls to reminds, click the top left corner to enter the mobile phone APP management interface – Device Management – Intelligent Reminder -selector switch. When phone calls wristband will vibrate end remind.

11. SMS / Applications reminder: mobile application APP open the switch of SMS alerts / reminders, click the top left comer to enter the mobile phone APP management interface – Device Management -Intelligent Reminder – selecting switch.

HR Tips

1. Most people has the heart rate of about 60-120.

2. Moet people resting heart rate is 60 to 90 beats / minute, the optimal heart rate is up to 70 beats / minute.

3. The heart rate of athletes and trained people is 40 to 60 beats / minute.

4. Heart rate is always been changing, and after exercise, after eating, personal circumstance. factors, good or bad mood, etc., are heart rate constantly changing factors.

5. When doing Aerobic exercise to an effective and safe condition, people’s heart rate is 170, minus age, people should hold the heart rate between 108 to 144.

6. Please Exercise regularly, proper diet, weight control, psychological adjustment, to make themselves more healthy and happy every day.

Blood Oxygen Tips

1.Oxygen saturation is the the percentage of oxygen-bound oxyhemoglobin (Hb02) capacity vs total hem-oglobin (Hb) combined capacity, that is the concentr-ation of oxygen in the blood.

Blood Pressure Tips

1. Systolic blood pressure, arterial blood delivered to the highest value when referred to as “high pressure”, the heart for the next time the lowest blood pressure value reserve dilate when blood is called “low-voltage”, are ref erred to as systolic and diastolic blood pressure.

2. Most people has the heart rate of i80 blood pressure (low pressure) to 120 (high pressure) around.

3. Within the normal range, blood pressure has diff differentiation of age, gender. Generally, the elderly have the higher blood pressure than the young, men have the high blood pressure than women.

4. Blood pressure is always been changing, and afterexercise, after eating, personal circumstances factors, good or bad mood, etc., are heart rate constantly changing factors.

5. Please Exercise regularly, proper diet, weight control, psychological adjustment, to make themselves more healthy and happy every day.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, i f not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interfere by one or more of the following measures:
-Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. technician for help.

– Consult the dealer or an experienced radio[TV Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1] This device may not cause harmful interference, and

[2] this device must accept any interference received, including interference that may cause undesired operation.
Questions about your M2 Smart Watch? Post in the comments!
Download M2 Smart Watch Manual [PDF]

References

• User Manual