Shelly – UseManuals

Shelly Dimmer 2 Smart WiFi Switch Manual

ItsManual — Tue, 29 Nov 2022 16:06:49 +0000

Smart WiFi Dimmer Switch USER GUIDE

The Shelly® smart WiFi dimmer by Allterco Robotics is intended to be installed directly to your lights in order to control and dim the light. It is intended to be mounted into a standard in-wall console, behind the light switches or other places with limited space. Shelly may work as a standalone device or as an accessory to a home automation controller.
SHELLY DIMMER CANNOT BE CONNECTED AND OPERATE A FAN. DOING SO MAY CAUSE DAMAGE TO THE UNIT OR FAN, INCLUDING CAUSING A FIRE!!!
LEGEND:
SW1 – Switch input 1 for on/off/dimming
SW2 – Switch input 2 for on/off/dimming
O – Output
L – Line input (110-240V)
N – Neutral input (Zero)

*When using the device without neutral, Shelly Dimmer 2 requires at least 10W of power consumption, in order to operate. If the connected light has a smaller power consumption, then Shelly Bypass is required for the operation of the Device.

Specification

Power supply:
110-240V ±10%
50/60Hz AC
Operational current:
0.1 – 1.1A
Device temperature protection:
105°C
Complies with EU standards:
• RE Directive
2014/53/EU
• LVD 2014/35/EU
• EMC 2004/108/WE • RoHS2 2011/65/UE

Working temperature:
from 0°C to 35°C
Radio signal power:
1mW
Radio protocol:
WiFi 802.11 b/g/n
Frequency:
2400 – 2500 MHz;
Operational range
(depending on local construction):
• up to 50 m outdoors
• up to 30 m indoors

Dimensions (HxWxL):
42 x 36 x 14 mm
Electrical consumption:
< 1,5 W
Supported light types:
• Incandescent and halogen light sources:
1-220W
• Dimmable LED : 50200VA / 1W – 200W
• Resistive-inductive loads ferromagnetic
transformers: 50150VA

Introduction to Shelly®

Shelly® is a family of innovative Devices, which allow remote control of electric appliances through mobile phones, PC or home automation systems. Shelly ® uses WiFi to connect to the devices controlling it. They can be in the same WiFi network or they can use remote access (through the Internet). Shelly ® may work standalone, without being managed by a home automation controller, in the local WiFi network, as well as through a cloud service, from everywhere the User has Internet access. Shelly ® has an integrated web server, through which the User may adjust, control and monitor the Device. Shelly ® has two WiFi modes – access Point (AP) and Client mode (CM). To operate in Client Mode, a WiFi router must be located within the range of the Device. Shelly®devices can communicate directly with other WiFi devices through HTTP protocol.
An API can be provided by the Manufacturer. Shelly ® devices may be available for monitoring and control even if the User is outside the range of the local WiFi network, as long as the WiFi router is connected to the Internet. The cloud function could be used, which is activated through the web server of the Device or through the settings in the Shelly Cloud mobile application.
The User can register and access Shelly Cloud, using either Android or iOS mobile applications, or any internet browser and the website: https://my.Shelly.cloud/.

Technical Information

Control through WiFi from a mobile phone, PC, automation system or any other Device supporting HTTP and/or UDP protocol.
Microprocessor management.
Shelly may be controlled by an external button/switch.

Installation Instructions

Initial Inclusion

Before installing/mounting the Device ensure that the grid is powered off (turned down breakers). Connect the Device to the power grid and install it in the console behind the switch/power socket following the scheme that suites the desired purpose.

Connecting to a standard power grid with neutral – fig. 1
Connecting to a power grid without neutral, with minimal consumption of 10W – fig 2.
Connecting to a standard power grid with neutral, and switches also connected to neutral – fig 3.
Connecting to a power grid without neutral, with no minimal consumption and using Shelly Bypass –fig 4

You may choose if you want to use Shelly with the Shelly Cloud mobile application and Shelly Cloud service. You can also familiarize yourself with the instructions for Management and Control through the embedded Web interface.

Control your home with your voice
All Shelly devices are compatible with Amazon Echo and Google Home. Please see our step-by-step guide on:
https://shelly.cloud/compatibility/Alexa
https://shelly.cloud/compatibility/Assistant

SHELLY ®MOBILE APPLICATION

http://shelly.cloud/app_download/?i=ios

http://shelly.cloud/app_download/?i=android

Shelly Cloud gives you the opportunity to control and adjust all Shelly ® Devices from anywhere in the world. You only need an internet connection and our mobile application, installed on your smartphone or tablet. To install the application please visit Google Play (Android – fig. 2) or App Store (iOS – fig. 3) and install the Shelly Cloud app.

Registration
The irst time you load the Shelly Cloud mobile app, you have to create an account that can manage all your Shelly ® devices.
Forgotten Password
In case you forget or lose your password, just enter the e-mail address you have used in your registration. You will then receive instructions to change your password.
WARNING! Be careful when you type your e-mail address during the registration, as it will be used in case you forget your password.
After registering, create your first room (or rooms), where you are going to add and use your Shelly devices.

Shelly Cloud gives you the opportunity to create scenes for automatic turning on or off of the Devices at predefined hours or based on other parameters like temperature, humidity, light etc. (with the available sensor in Shelly Cloud). Shelly Cloud allows easy control and monitoring using a mo- bile phone, tablet or PC.
Device Inclusion
To add a new Shelly device, install it to the power grid following the Installation Instructions included with the Device.

Step 1
After the installation of Shelly and the power is turned on, Shelly will create its own WiFi Access Point (AP).
WARNING: In case the Device has not created its own WiFi network with SSID like shellydimmer2-35FA58 check if you have connected Shelly correctly by the wiring schemes. If you do not see an active WiFi network with SSID like shellydimmer2-35FA58, reset the Device. If the device has been powered on, you have to power it off and on again. After turning the power on, you have 60 seconds to press5 consecutive times either switch connected I1/I2. Or if you have physical access to the device, press and hold the reset button for 10 seconds. Shelly should return to AP Mode. If not, please repeat or contact our customer support at:
Step 2
Choose “Add Device”.
In order to add more Devices later, use the app menu at the top right corner of the main screen and click “Add Device”. Type the name (SSID) and password for the WiFi network, to which you want to add the Device.

Step 3
If using iOS: you will see the following screen:

Press the home button of your iPhone/iPad/iPod. Open Settings > WiFi and connect to the WiFi network created by Shelly, e.g. shellydimmer2-35FA58.
If using Android: your phone/tablet will automatically scan and include all new Shelly Devices in the WiFi network that you are connected to.

Upon successful Device Inclusion to the WiFi network, you will see the following pop-up:

Step 4:
Approximately 30 seconds after the discovery of any new Devices оn the local WiFi network, а list will be displayed by default in the “Discovered Devices” room.

Step 5:
Enter Discovered Devices and choose the Device you want to include in your account.

Step 6:
Enter a name for the Device (in the Device Name field). Choose a Room, in which the Device has to be positioned. You can choose an icon or add a picture to make it easier to recognize. Press “Save Device”.

Step 7:
To enable connection to the Shelly Cloud service for remote control and monitoring of the Device, press “YES” on the following pop-up.

Shelly devises Settings
After your Shelly device is included in the app, you can control it, change its settings and automate the way it works. To switch the device on and off, use the Power button.
To enter at the details menu of the device, click on it’s name. From the details menu, you may control the Device, as well as edit its appearance and settings.

Weekly Schedule

This function requires an Internet connection.
To use the Internet, your Shelly has to be connected to a local WiFi network with an active internet connection. Shelly may turn on/off automatically at a predefined time, at sunrise/ sunset, or at a specified time before or after sunrise/sunset. Multiple schedules are possible. Internet/Security WiFi Mode – Client: This allows the device to connect to an available WiFi network. After typing the details in the respective fields, press Connect.
WiFi Client Backup: Add a backup WiFi network, in case your primary one becomes unavailable.
WiFi Mode – Acess Point: Configure Shelly to create a Wi-Fi Access point. After typing the details in the respective fields, press Create Access Point.
Cloud: Enable or Disable connection to the Cloud service.
Restrict Login: Restrict the web interface of Shely with a Username and Password.
After typing the details in the fields, press Restrict Shelly.
Settings
Power-On Default Mode
This sets the default output state when Shelly is powered.
ON: Configure Shelly to turn ON, when it has power.
OFF: Configure Shelly to turn OFF when it has power.
Restore Last Mode: Configure Shelly to return to the last state it was in, when it has power.
Firmware Update
Update the firmware of Shelly, when a new version is released.
Button Type

One Button mode: the device is controlled with a single switch.
Dual button mode: the device is a controlled dual switch.
Toggle switch one button: the device is controlled by a single toggle switch.
Edge switch: the device is controlled with an edge on/off.

Button Debounce
Adjust the sensitivity (time of reaction) of the connected switch. If there are any interferences in the power grid, this will prevent undesired status change (on/off) of the device.
Range: 60 – 200 ms
Calibration
Shelly Dimmer needs calibration based on the type of light that you are going to use it with. To make a calibration, press Start Calibration.
Transition Time
Set the time (in milliseconds), for which Shelly Dimmer goes from 0% to 100%. The value can be from 0 to 5000 ms.
Fade rate
Set the speed of dimming, when the switch is pressed and held.

Range: 1x – 5x

Minimum Brightness
If the connected light is not working below a certain percentage, you can set the minimum percent at which Shelly Dimmer will turn on. Once set, you can not dim the light below the minimum.

Range: 0 – 50% Warm-up

Some lights require a certain power impulse, in order to start below 100% brightness. You can set the brightness level and time at which Shelly Dimmer will turn on.

Brightness range: 10 – 100%
Time range: 20 – 200 ms

Night Mode
With this model, you can set a period of time and level of brightness, in which any turning on will set the brightness to the predefined level.

Time Zone and Geo-location
Enable or Disable the automatic detection of Time Zone and Geo-location.
Factory Reset
Return Shelly to its factory default settings.
Device Information
Here you can see the:

Device ID – Unique ID of Shelly
Device IP – The IP of Shelly in your Wi-Fi network

The Embedded Web Interface

Еven without the mobile app, Shelly can be set and controlled through a browser and WiFi connection of a mobile phone, tablet, or PC.
Abbreviations used:

Shelly-ID – the unique name of the Device. It consists of 6 or more characters. It may include numbers and letters, for example, 35FA58.
SSID – The name of the WiFi network, created by the Device, for example, shellydimmer2-35FA58.
Access Point (AP) – the mode in which the device creates its own WiFi connection point with the respective name (SSID).
Client Mode (CM) – the mode in which the device is connected to another WiFi network.

Initial inclusion
Step 1
Connect Shelly to the power grid following the wiring schemes. Shelly will create its own WiFi network (AP).
WARNING: In case the Device has not created its own WiFi network with SSID like shellydimmer2-35FA58 check if you have connected Shelly correctly by the wiring schemes. If you do not see an active WiFi network with SSID like shellydimmer2-35FA58, reset the Device. If the device has been powered on, you have to power it off and on again. After turning the power on, you have 60 seconds to press 5 consecutive times either switch connected I1/I2. Or if you have physical access to the device, press and hold the reset button for 10 seconds. Shelly should return to AP Mode. If not, please repeat or contact our customer support at:
Step 2
When Shelly has created their own WiFi network (own AP), with name (SSID) such as shellydimmer2-35FA58. Connect to it with your phone, tablet, or PC.
Step 3
Type 192.168.33.1 into the address field of your browser to load the web interface of Shelly.

Home Page

This is the home page of the embedded web interface. If it has been set up is correct, you will see information about:

Current state (on/off)
Current brightness level
Power button
Connection to Cloud
Present time
Settings

Тo manages the power supply automatically, you may use:
Auto OFF: After turning on, the power supply will automatically shut down after a predefined time (in seconds). A value of 0 will cancel the automatic shutdown.
Auto ON: After turning off, the power supply will be automatically turned on after a predefined time (in seconds). A value of 0 will cancel the automatic power-on.
Weekly Schedule
This function requires an Internet connection.
To use the Internet, a Shelly Device has to be connected to a local WiFi network with a working internet connection. Shelly may turn on/off automatically at a predefined time, at sunrise/ sunset, or at a specified time before or after sunrise/sunset. Multiple schedules are possible.
Internet/Security
WiFi Mode – Client
Allows the device to connect to an available WiFi network. After typing the details in the ields, press Connect.
WiFi Client Backup
Add a backup WiFi network, in case your primary one becomes unavailable.
WiFi Mode – Acess Point
Configure Shelly to create a Wi-Fi Access point. After typing the details in the fields, press Create Access Point.

Cloud
Enable or Disable connection to the Cloud service.
Restrict Login
Restrict the web interface of Shely with a Username and Password. After typing the details in the fields, press Restrict Shelly.
SNTP Server
You can set a custom SNTP Server. Type the URL address and press Save.
ATTENTION! If you have entered incorrect information (wrong settings, usernames, passwords etc.), you will not be able to connect to Shelly and you have to reset the Device.
WARNING: In case the Device has not created its own WiFi network with SSID like shellydimmer2-35FA58 check if you have connected Shelly correctly by the wiring schemes. If you do not see an active WiFi network with SSID like shellydimmer2-35FA58, reset the Device. If the device has been powered on, you have to power it off and on again. After turning the power on, you have 60 seconds to press 5 consecutive times either switch connected I1/I2. Or if you have physical access to the device, press and hold the reset button for 10 seconds. Shelly should return to AP Mode. If not, please repeat or contact our customer support at:

Advanced – Developer Settings
Here you can change the action execution:

Via CoAP (CoIOT)
Via MQTT

Firmware Upgrade
Shows present firmware version. If a newer version is available, officially announced, and published by the Manufacturer, you can update your Shelly Device. Click Upload to install it to your Shelly Device.

Settings
Power-On Default Mode
This sets the default output state when Shelly is powered.
ON: Configure Shelly to turn ON, when it has power.
OFF: Configure Shelly to turn OFF when it has power.
Restore Last Mode
Configure Shelly to return to the last state it was in when it has power.
SWITCH
Configure Shelly to operate accordingly to the state of the switch (button).
Time Zone and Geo-location
Enable or Disable the automatic detection of Time Zone and Geo-location.
Firmware Update
Update the firmware of Shelly, when a new version is released.
Button Type

One Button mode: the device is controlled with a single switch.
Dual button mode: the device is a controlled dual switch.
Toggle switch one button: the device is controlled by a single toggle switch.
Edge switch: the device is controlled with an edge on/off.

Range: 60 – 200 ms

Calibration
Shelly Dimmer needs calibration based on the type of light that you are going to use it with. To make a calibration, press Start Calibration.
Transition Time
Set the time (in milliseconds), for which Shelly Dimmer goes from 0% to 100%. The value can be from 0 to 5000 ms.
Fade Rate
Set the speed of dimming, when the switch is pressed and held.

Range: 1x – 5x

Range: 0 – 50%

Warm-up Some lights require a certain power impulse, in order to start below 100% brightness. You can set the brightness level and time at which Shelly Dimmer will turn on.

Brightness range: 10 – 100%
Time range: 20 – 200 ms

Night Mode
With this model, you can set a period of time and level of brightness, in which any turning on will set the brightness to the predefined level.
Factory Reset
Return Shelly to its factory default settings.
Device Reboot
Reboots the device.
Device Information
Here you can see the unique ID of Shelly.
Additional Features
Shelly allows control via HTTP from any other device, home automation controller, mobile app or server. For more information about the REST control protocol, please visit:
https://shelly.cloud/developers/ or send a request to:

Environmental Protection

This marking on the device, accessories, or documentation indicates that the device and its electronic accessories must be disposed of only in specially designated locations.
This marking on the battery, the instruction manual, the safety instructions, the warranty card or the packaging indicates that the battery in the device must be disposed of only in specially designated locations.
Please follow the instructions for environmental protection and proper disposal of the Device, its accessories, and its packaging for the recycling of the materials for their further usage and to keep the environment clean!

Warranty Terms

The Device’s warranty term is 24 (twenty-four) months, beginning since the date of purchase by the End User. The Manufacturer does is not responsible for extra warranty terms by the Еnd Seller.
The Warranty is valid for the territory of EU. The warranty is applicable in compliance with all relevant laws and users’ rights protections. The purchaser of the Device is entitled to exercise his/ her rights in accordance with all applicable laws and regulations.
Warranty terms are provided by Allterco Robotics EOOD (referred hereinafter as the Manufacturer), incorporated under the Bulgarian law, with the address of registration 109 Bulgaria Blvd, floor 8, Triaditsa Region, Soia 1404, Bulgaria, registered with the Commercial Register kept by the Bulgarian Ministry of Justice’s Registry Agency under United Identity Code (UIC) 202320104.
Claims regarding the Conformity of the Device with the terms of the contract of sale shall be addressed to the Seller, in accordance with its terms of sale.
Damages such as death or bodily injury, deterioration or damages to objects different from the defective product, caused by a defective product, are to be claimed against the A manufacturer using the contact data of the Manufacturer’s company.
The User may contact the Manufacturer at for operational problems that may be resolved remotely. It is recommended that the User contact the Manufacturer before sending it for servicing.
The terms of removing defects depend on the commercial terms of the Seller. The Manufacturer is not responsible for untimely servicing of the Device or for faulty repairs carried out by unauthorized service.
When exercising their rights under this warranty, the User must provide the Device with the following documents: receipt and valid warranty card with date of purchase.
After a warranty repair has been carried out, the warranty period is extended only for that period.
The warranty does NOT cover any damages to the Device which occur in the following circumstances:

When the Device has been used or wired inappropriately, in- cluding inappropriate fuses, overpassing maximal values of load and current, electric shock, short circuit, or other problems in the power supply, the power grid or the radio network.
When there is a non-compliance between warranty card and/ or without a purchase receipt, or attempted forgery of these documents, including (but not limited to) the warranty card or the documents proving the purchase.
When there has been a self-repair attempt, (de)installation, modification, or adaptation of the Device by unauthorized persons.
Intentional or negligent improper handling, storing or transportation of the Device, or in the event of non-observance of the instructions included in this warranty.
When a non-standard power supply, network, or faulty Devices have been used.
When damages occur which were caused regardless of the Manufacturer, including but not limited to: floods, storms, ire, lightning, natural disasters, earthquakes, war, civil wars, other force majeure, unforeseen accidents, robbery, water damage, any damages made by ingress of liquids, weather conditions, solar heating, any damages made by the intrusion of sand, humidity, high or low temperature, or air pollution.
When there are other reasons beyond manufacturing defect, including but not limited to: water damage, ingress of liquid into the Device, weather conditions, solar overheating, intrusion of sand, humidity, low or high temperature, air pollution.[u1]
When there have been mechanical damages (forced opening, breaking, cracks, scratches, or deformations) caused by a hit, fall, or from another object, wrong use, or caused by not following the instructions for use.
When damage has been caused by exposing the Device to severe outdoor conditions such as: high humidity, dust, too low or too high temperature. Terms of proper storage are specified in the User Manual.
When damage has been caused by lack of maintenance by the User, as specified in the User manual.
When damage has been caused by faulty accessories or those not recommended by the Manufacturer.
When damage has been caused by the use of non-original spare parts or accessories not suitable for the specified Device model, or after repairs and changes carried out by unauthorized service or person.
• When damage has been caused by the use of faulty Devices and/or accessories.
• When damage has been caused by faulty software, a computer virus or other harmful behavior on the Internet, or by lack of software updates or incorrect updates by a method not provided by either the manufacturer or by the Manufacturer’s software.

11. The range of warranty repairs does not include periodical maintenance and inspections, particularly cleaning, adjustments, checks, bug fixes or program parameters, and other activities that must be performed by the User (Buyer). The warranty does not cover the wear of the Device, because such elements have a limited lifespan.
12. The manufacturer is not responsible for any property damage caused by a defect in the Device. The Manufacturer is not liable for indirect damages (including but not limited to loss of profits, savings, lost profits, claims by third parties) in connection with any defect of the Device, nor for any property damage or personal injury arising out of or related to the use of the Device.
13. The Manufacturer is not responsible for damage caused by circumstances independent of the Manufacturer, including but not limited to: floods, storms, fire, lightning, natural disasters, earthquakes, war, civil unrest and other force majeure, unforeseen accidents, or theft.

Manufacturer: Allterco Robotics EOOD
Address: Soia, 1407, 103 Cherni vrah blvd.
Tel.: +359 2 988 7435
E-mail:
http://www.Shelly.cloud
The Declaration of Conformity is available at: https://Shelly.cloud/declaration-of-conformity/
Changes in the contact data are published by the Manufacturer at the official website of the Device: http://www.Shelly.cloud
The User is obliged to stay informed of any amendments of these warranty terms before exercising his/her rights against the Manufacturer. All rights to trademarks She® and Helly ®, and other intellectual rights associated with this Device belong to Allterco Robotics EOOD.

Shelly 1 Smart WiFi Relay Manual

ItsManual — Fri, 25 Nov 2022 10:47:57 +0000

SHELLY 1 SMART WIFI RELAY Installation Guide

Product overview

Fig 1.

Fig 2

Legend

N – Neutral input (Zero)/( + )
L – Line input (110-240V)/( – )
O – Output
I – Input
SW – Switch (input) controlling O The WiFi Relay Switch Shelly® 1 may control 1 electrical circuit up to 3.5 kW. It is intended to be mounted into a standard in-wall console, behind power sockets and light switches or other places with limited space. Shelly may work as a standalone Device or as an accessory to another home automation controller.
Purpose of control: Operating
Construction of control: Independently mounted
Type 1.B Action
Pollution Degree 2
Impulse Voltage: 4000 V
Indication of proper terminal connection

Specification

Power supply – 110-240V ±10% 50/60Hz AC, 24-60V DC, 12V DC
Max load – 16A/240V
Complies with EU standards – RE Directive 2014/53/EU, LVD 2014/35/EU, EMC 2004/108/WE, RoHS2 2011/65/UE
Working temperature – -40°C up to 40°C
Radio signal power – 1mW
Radio protocol – WiFi 802.11 b/g/n
Frequency – 2412-2472 МHz;
Operational range (depending on local construction) – up to 50 m outdoors, up to 30 m indoors
Dimensions (HxWxL) – 41x36x17 mm
Electrical consumption – < 1 W

Technical Information

Control through WiFi from a mobile phone, PC, automation system or any other Device supporting HTTP and/or UDP protocol.
Microprocessor management.
Controlled elements: 1 electrical circuits/appliances.
Controlling elements: 1 relays.
Shelly may be controlled by an external button/switch

Introduction to Shelly

Shelly® is a family of innovative Devices, which allow remote control of electric appliances through mobile phone, PC or home automation system. Shelly® uses WiFi to connect to the devices controlling it. They can be in the same WiFi network or they can use remote access (through the Internet). Shelly® may work standalone, without being managed by a home automation controller, in the local WiFi network, as well as through a cloud service, from everywhere the User has Internet access. Shelly® has an integrated web server, through which the User may adjust, control and monitor the Device. Shelly® has two WiFi modes – access Point (AP) and Client mode (CM). To operate in Client Mode, a WiFi router must be located within the range of the Device. Shelly® devices can communicate directly with other WiFi devices through HTTP protocol. An API can be provided by the Manufacturer. Shelly® devices may be available for monitor and control even if the User is outside the range of the local WiFi network, as long as the WiFi router is connected to the Internet. The cloud function could be used, which is activated through the web server of the Device or through the settings in the Shelly Cloud mobile application. The User can register and access Shelly Cloud, using either Android or iOS mobile applications, or any internet browser and the web site: https://my.Shelly.cloud/.

Installation Instructions

CAUTION!
Danger of electrocution. The mounting/installation of the Device should be done by a qualified person (electrician).

CAUTION!
Danger of electrocution. Even when the Device is turned off, it is possible to have voltage across its clamps. Every change in the connection of the clamps has to be done after ensuring all local power is powered off/disconnected.

CAUTION!
Do not connect the Device to appliances exceeding the given max load!

CAUTION!
Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.

CAUTION!
Before beginning the installation please read
the accompanying documentation carefully and completely. Failure to follow recommended procedures could lead to
malfunction, danger to your life or violation of the law. Allterco
Robotics is not responsible for any loss or damage in case of
incorrect installation or operation of this Device.

CAUTION!
Use the Device only with power grid and appliances which comply with all applicable regulations. short circuit in the power grid or any appliance connected to the Device
may damage the Device.

RECOMMENDATION!
Тhe Device may be connected to and may control electric circuits and appliances only if they comply with the respective standards and safety norms.

RECOMMENDATION!
The Device may be connected with solid single-core cables with increased heat resistance to insulation not less than PVC T105°C.

Declaration of conformity

Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly 1 is in compliance with Directive 2014/53/ EU, 2014/35/EU, 2004/108/WE, 2011/65/UE. The full text of the EU declaration of conformity is available at the following internet address https://shelly.cloud/knowledge-base/devices/shelly-1/

Manufacturer:
Allterco Robotics EOOD Address: Sofia, 1407, 103 Cherni vrah Blvd.

Tel.: +359 2 988 7435
E-mail:
Web: http://www.shelly.cloud
Changes in the contact data are published by the Manufacturer at the official website of the Device http://www.shelly.cloud
The User is obliged to stay informed for any amendments of these warranty terms before exercising his/her rights against the Manufacturer. All rights to trademarks She® and Shelly® , and other intellectual rights associated with this Device belong to Allterco Robotics EOOD.

Shelly 2.5 Smart Wifi Relay Manual

ItsManual — Wed, 30 Nov 2022 15:23:48 +0000

SHELLY 2.5 SMART WIFI RELAY

Legend

N – Neutral input (110-240V AC); + Positive input (30-50V DC)
L – Line input (110-240V AC); – Negative input (30-50V DC)
O1 – Output 1;
O2 – Output 2;
SW1 – Switch 1 (input controlling O1);
SW2 – Switch 2 (input controlling O2).

The Shelly® Dual WiFi Relay Switch by Allterco Robotics is intended to be mounted into a standard in-wall console, behind power sockets and light switches in order to control and monitor the electric power through it, independent for each channel. Shelly may work as a standalone Device or as an accessory to a home automation controller.

Purpose of control is operating
Construction of control is independently mounted
Type 1.B Action
Pollution Degree 2
Impulse Voltage: 4000 V

Specification

Power supply – 110-240V ±10% 50/60Hz AC, 30-50V DC
Max load per channel – 10A/240V, 50/60Hz
Complies with EU standards – RE Directive 2014/53/EU, LVD 2014/35/EU, EMC 2014/30/EU, RoHS2 2011/65/EU
Working temperature -20°C up to 40°C
Radio signal power – 1mW
Radio protocol – WiFi 802.11 b/g/n
Frequency – 2412-2472 МHz; (Max. 2483.5MHz)
Operational range (depending on local construction) – up to 50 m outdoors, up to 30 m indoors
Dimensions (HxWxL) – 39x36x17 mm
Electrical consumption – <1W

Technical Information

Control through WiFi from a mobile phone, PC, automation system or any other Device supporting HTTP and/or UDP protocol.
Microprocessor management.
Controlled elements: 2 electrical circuits/appliances.
Controlling elements: 2 relays.
Shelly may be controlled by an external button/switch.

CAUTION! Danger of electrocution. Mounting the Device to the power grid has to be performed with caution.

CAUTION! Do not allow children to play with the button/switch connected the Device. Keep the Devices for remote control of Shelly (mobile phones, tablets, PCs) away from children.

Introduction to Shelly

Shelly is a family of innovative Devices, which allow remote control of electric appli-ances through mobile phone, PC or home automation system. Shelly® uses WiFi to connect to the devices controlling it. They can be in the same WiFi network or they can use remote access (through the Internet). Shelly® may work standalone, without being managed by a home automation controller, in the local WiFi network, as well as through a cloud service, from everywhere the User has Internet access.

An API can be provided by the Manufacturer. Shelly® devices may be available for monitor and control even if the User is outside the range of the local WiFi network, as long as the WiFi router is connected to the Internet. The cloud function could be used, which is activated through the web server of the Device or through the settings in the Shelly Cloud mobile application.

The User can register and access Shelly Cloud, using either Android or iOS mobile applications, or any internet browser and the web site: https://my.Shelly.cloud/.

Installation Instructions

CAUTION! Danger of electrocution. The mounting/installation of the Device should be done by a qualified person (electrician).

CAUTION! Danger of electrocution. Even when the Device is turned off, it is possible to have voltage across its clamps. Every change in the connection of the clamps has to be done after ensuring all local power is powered off/disconnected.

CAUTION! Do not connect the Device to appliances exceeding the given max load!

CAUTION! Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.

CAUTION! Before beginning the installation please read the accompanying documentation carefully and completely. Failure to follow recommended procedures could lead to malfunction, danger to your life or violation of the law. Allterco Robotics is not responsible for any loss or damage in case of incorrect installation or operation of this Device.

CAUTION! Use the Device only with power grid and appliances which comply with all applicable regulations. short circuit in the power grid or any appliance connected to the Device may damage the Device.

RECOMMENDATION! Тhe Device may be connected to and may control electric circuits and appliances only if they comply with the respective standards and safety norms.

RECOMMENDATION! The Device may be connected with solid single-core cables with increased heat resistance to insulation not less than PVC T105°C.

Declaration of conformity

Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly 2.5 is in compliance with Directive 2014/53/EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: https://shelly.cloud/knowledge-base/devices/shelly-25/

Manufacturer: Allterco Robotics EOOD

Address: Bulgaria, Sofia, 1407, 103 Cherni vrah Blvd.

Tel.: +359 2 988 7435

Web: http://www.shelly.cloud

Changes in the contact data are published by the Manufacturer at the official website of the Device http://www.shelly.cloud

All rights to trademarks She® and Shelly® , and other intellectual rights associated with this Device belong to Allterco Robotics EOOD.

Shelly 1PM Smart WiFi Relay manual

ItsManual — Wed, 15 Mar 2023 13:22:41 +0000

Shelly 1PM Smart WiFi Relay User Guide

Product Overview

Power supply: 110-240V AC
Power supply: 110-240V AC

Legend

N – Neutral input (Zero)/( + )
L – Line input (110-240V)/( – )
L1 – Line input for relay power
SW – Switch (input) controlling O
O – Output

The WiFi Relay Switch Shelly 1PM can control 1 electrical circuit up to 3.5 kW. It is intended to be mounted into a standard in-wall console, behind power sockets and light switches or other places with limited space. Shelly may work as a standalone Device or as an accessory to another home automation controller.

Purpose of control: Operating
Construction of control: Independently mounted
Type 1.B Action
Pollution Degree 2
Impulse Voltage: 4000 V
Indication of proper terminal connection

Specification

Power supply – 110-240V ±10% 50/60Hz AC, 24-60V DC
Max load – 16A/240V
Complies with EU standards – RE Directive 2014/53/EU LVD 2014/35/EU, EMC 2004/108/WE, RoHS2 2011/65/UE
Working temperature – – 40°C up to 40°C
Radio signal power – 1mW
Radio protocol – WiFi 802.11 b/g/n
Frequency – 2412 – 2472 МHz;
Operational range (depending on local construction) – up to 50 m outdoors, up to 30 m indoors
Dimensions (HxWxL) – 41x36x17 mm
Electrical consumption – <1W

Technical Information

Control through WiFi from a mobile phone, PC, automation system or any other Device supporting HTTP and/or UDP protocol.
Microprocessor management.
Controlled elements: 1 electrical circuits/appliances.
Controlling elements: 1 relays.
Shelly may be controlled by an external button/switch.
Shelly may monitor the power consumption and save it, free on our Cloud, with history up to 1 year.

CAUTION! Danger of electrocution. Mounting the Device to the power grid has to be performed with caution.

CAUTION! Do not allow children to play with the button/ switch connected the Device. Keep the Devices for remote control of Shelly (mobile phones, tablets, PCs) away from children.

Introduction to Shelly

Shelly® has an integrated web server, through which the User may adjust, control and monitor the Device. Shelly® has two WiFi modes – access Point (AP) and Client mode (CM). To operate in Client Mode, a WiFi router must be located within the range of the Device. Shelly® devices can communicate directly with other WiFi devices through HTTP protocol.
An API can be provided by the Manufacturer. Shelly® devices may be available for monitor and control even if the User is outside the range of the local WiFi network, as long as the WiFi router is connected to the Internet. The cloud function could be used, which is activated through the web server of the Device or through the settings in the Shelly Cloud mobile application.

The User can register and access Shelly Cloud, using either Android or iOS mobile applications, or any internet browser and the web site: https://my.shelly.cloud/

Installation Instructions

CAUTION! Danger of electrocution. The mounting/installation of the Device should be done by a qualified person (electrician).

CAUTION! Danger of electrocution. Even when the Device is turned off, it is possible to have voltage across its clamps. Every change in the connection of the clamps has to be done after ensuring all local power is powered off/disconnected.

CAUTION! Do not connect the Device to appliances exceeding the given max load!

CAUTION! Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.

CAUTION! Before beginning the installation please read the accompanying documentation carefully and completely. Failure to follow recommended procedures could lead to malfunction, danger to your life or violation of the law. Allterco Robotics is not responsible for any loss or damage in case of incorrect installation or operation of this Device.

CAUTION! Use the Device only with power grid and appliances which comply with all applicable regulations. Short circuit in the power grid or any appliance connected to the Device may damage the Device.

RECOMMENDATION! Тhe Device may be connected to and may control electric circuits and appliances only if they comply with the respective standards and safety norms.

RECOMMENDATION! The Device may be connected with solid single-core cables with increased heat resistance to insulation not less than PVC T105°C.

Declaration of conformity

Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly 1PM is in compliance with Directive 2014/53/EU, 2014/35/EU, 2004/108/WE, 2011/65/UE. The full text of the EU declaration of conformity is available at the following internet address:
https://shelly.cloud/knowledge-base/devices/shelly-1pm/

Contact Us

Manufacturer: Allterco Robotics EOOD
Address: Sofia, 1407, 103 Cherni vrah Blvd.
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Web: http://www.shelly.cloud
Changes in the contact data are published by the Manufacturer at the official website of the Device: http://www.shelly.cloud
The User is obliged to stay informed for any amendments of
these warranty terms before exercising his/her rights against the Manufacturer.
All rights to trademarks She® and Shelly® , and other intellectual rights associated with this Device belong to Allterco Robotics EOOD.

Shelly Plus 1PM WiFi Wlan Switching Actuator manual

ItsManual — Sat, 08 Apr 2023 06:11:37 +0000

Shelly Plus 1PM WiFi Wlan Switching Actuator

Shelly Plus 1PM

This document contains important technical and safety information about the device and its safety use and installation. Before beginning the installation, please read this guide and any other documents accompanying the device carefully and completely. Failure to follow the installation procedures could lead to malfunction, danger to your health and life, violation of the law or refusal of legal and/or commercial guarantee (if any). Allterco Robotics is not responsible for any loss or damage in case of incorrect installation or improper operation of this device due to failure of following the user and safety instructions in this guide.

Introduction to Shelly

Shelly® is a line of innovative Devices, which allow remote control of electric appliances through a mobile phone, tablet, PC, or home automation system. Shelly® may work standalone on the local WiFi network, without being managed by a home automation controller, or it can also work through cloud home automation services. Shelly® devices can be accessed, controlled, and monitored remotely from any place the User has Internet connectivity, as long as the devices are connected to a WiFi router and the Internet. Shelly® has an integrated web server, through which the User may adjust, control and monitor the Device. The cloud function could be used, if it is activated through the web server of the Device or the settings in the Shelly Cloud mobile application. The User can register and access Shelly Cloud using either Android or iOS mobile application, or with any internet browser at https://my.shelly.cloud/
Shelly® Devices have two WiFi modes – Access Point (AP) and Client mode (CM). To operate in Client Mode, a WiFi router must be located within the range of the Device. Devices can communicate directly with other WiFi devices through HTTP protocol. An API can be provided by the Manufacturer.
CAUTION! Before beginning the installation please read the accompanying documentation carefully and completely. Failure to follow recommended procedures could lead to malfunction, danger to your life or violation of the law. Allterco Robotics is not responsible for any loss or damage in case of incorrect installation or operation of this Device.

Legend

N – Neutral input (Zero)
L – Line input (110-240V)
O – Output
SW – Switch (input) controlling O

Installation Instructions

CAUTION! Danger of electrocution. The mounting/installation of the Device should be done by a qualified person (electrician).
CAUTION! Do not connect the Device to appliances exceeding the given max load!
CAUTION! Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.
CAUTION! Use the Device only with a power grid and appliances which comply with all applicable regulations. short circuit in the power grid or any appliance connected to the Device may damage the Device.
RECOMMENDATION! he Device may be connected to and may control electric circuits and appliances only if they comply with the respective standards and safety norms.
RECOMMENDATION! The Device may be connected with solid single-core cables with increased heat resistance to insulation not less than PVC T105°C.
Before installing/mounting the Device ensure that the grid is powered off (turned down breakers). Connect the Relay to the power grid and install it in the console behind the switch/power socket following the scheme that suites the desired purpose: Connecting to the power grid with power supply 110-240V AC (fig. 1) or 24-240V DC* Connecting to the power grid (fig.2).
* without power metering
The WiFi Relay Switch Shelly® Plus 1PM may control 1 electrical circuit up to 3.5 kW. It is intended to be mounted into a standard in-wall console, behind power sockets and light switches or other places with limited space. Shelly may work as a standalone Device or as an accessory to another home automation controller.
For inductive appliances, those that cause voltage spikes during switching on: electrical motors, as fans, vacuum cleaners and similar ones, RC snubber (0.1µF / 100 / 1/2W / 600V AC) should be wired between Output and Neutral of the circuit. Before starting, wire check that the breakers are turned off and there is no voltage on their terminals. This can be done with a phase meter or multimeter. When you are sure that there is no voltage, you can start wiring the cables according to fig.1. Install a wire from “O” to the load and from the load to the Neutral. Install also a wire from the Fuse to “L”.
Connect the Neutral to the device.The last step is to install a cable from the switch to the terminal SW. For more information, please visit: http://shelly-api-docs.shelly.cloud/#shelly-family-overview or contact us at: developers@shelly.cloud

Specification

Max load: 16A/240V
Working temperature: 0°C up to 40°C
Radio signal power: 1mW
Radio protocol: WiFi 802.11 b/g/n
Frequency: 2412-2472 Hz; (Max. 2483.5MHz)
Operational range (depending on local construction): – up to 50 m outdoors, up to 30 m indoors
Dimensions (HxWxL): 41x36x17 mm
Electrical consumption: < 1 W
Mounting: Wall box
Wi-Fi: YES · Bluetooth: v4.2
Basic/EDR: YES
Bluetooth modulation: GFSK, /4-DQPSK, 8-DPSK
Bluetooth frequency TX/RX – 2402 – 2480MHz
Temperature Protection: YES
Scripting (mjs): YES
HomeKit support: YES
MQTT: YES · URL Actions: 20
Scheduling: 50
AC power supply: 110-240 V
DC Power supply: 24-240 V
CPU: ESP32 · Flash: 4MB

Technical Information

Control through WiFi from a mobile phone, PC, automation system or any other Device supporting HTTP and/or UDP protocol.
Microprocessor management.
Controlled elements: 1 electrical circuits/appliances.
Controlling elements: 1 relays.
Shelly may be controlled by an external button/switch.

INITIAL INCLUSION

You may choose if you want to use Shelly with the Shelly Cloud mobile application and Shelly Cloud service. Instructions on how to connect your device to the Cloud and control it through the Shellly App can be found in the “App guide”. You can also familiarize yourself with the instructions for Management and Control through the embedded Web interface.

Declaration of conformity

Hereby, Allterco Robotics EOOD declares that the radio equipment type Shelly Plus 1PM is in compliance with Directive 2014/53/ EU, 2014/35/EU, 2014/30/EU, 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address https://shelly.cloud/knowledge-base/devices/shelly-plus-1pm
Manufacturer: Allterco Robotics EOOD
Address: Bulgaria, Sofia, 1407, 103 Cherni vrah Blvd.
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Web: http://www.shelly.cloud
Changes in the contact data are published by the Manufacturer at the official website of the Device http://www.shelly.cloud
All rights to trademarks She® and Shelly®, and other intellectual rights associated with this Device belong to Allterco Robotics EOOD.

Shelly 2246349 3EM Energy Meter Wi-Fi manual

ItsManual — Fri, 28 Apr 2023 05:45:23 +0000

3EM
USER GUIDE
TRIPLE PHASE WIFI ENERGY METER

3 phase wiring scheme

2 phase (US) wiring

1 phase + separate solar power measurement wiring

1 phase wiring up to 3 different circuits

Legend

Left Side:
N – Neutral input (110-230V AC);
VA – Line input of Phase A (110-230V AC);
VB – Line input of Phase B (110-230V AC);
VC – Line input of Phase C (110-230V AC);
I – Line input for contactor control
O – Output for contactor control

Right Side:
IN- IN+ Input for current transformer of Neutral*
IC- IC+ Input for current transformer of Phase C
IB- IB+ Input for current transformer of Phase B
IA- IA+ Input for current transformer of Phase A

The Triple Phase WiFi Energy Meter, Shelly 3EM by Allterco Robotics is intended to be mounted next to the breakers, in order to monitor the electric power through it, independent for each channel and heavy-duty contactor control. Shelly may work as a standalone device or as an accessory to a home automation controller. Shelly 3EM can measure incoming and outgoing energy.

Purpose of control: Operating
Construction of control: Independently mounted
Type 1.B Action
Pollution Degree 2
Impulse Voltage: 4000 V

Specification

Power supply: 110-230V ±10% 50/60Hz AC
Max measurement per channel: 120A/230V
Relay Max Load: 10A/230V
Complies with EU standards:
RED 2014/53/EU
LVD 2014/35/EU
EMC 2004/108/WE
RoHS2 2011/65/UE
Working temperature: – 40°C up to 40°C
Radio signal power: 1mW
Radio protocol: WiFi 802.11 b/g/n
Frequency: 2400 – 2500 MHz;
Operational range (depending on local construction):
up to 50 m outdoors
up to 30 m indoors
Dimensions(HxWxL): 73 x 57 x 22 mm
Electrical consumption: < 1 W

Energy Theft Detection

In order to have this feature available, you might need to update the firmware of your device. With an additional split-core current transformer, connected to the IN- IN+ terminal of Shelly 3EM, you may receive a notification, if there is any energy theft or leakage. Please follow the wiring diagrams in fig. 1 and 2, dependent on your application.

Introduction to Shelly
Shelly® is a family of innovative Devices, which allow remote control of electric appliances through mobile phones, PC, or home automation systems. Shelly® uses WiFi to connect to the devices controlling it. They can be in the same WiFi network or they can use remote access (through the Internet). Shelly® may work standalone, without being managed by a home automation controller, in the local WiFi network, as well as through a cloud service, from everywhere the User has Internet access. Shelly® has an integrated web server, through which the User may adjust, control and monitor the Device. Shelly® has two WiFi modes – access Point (AP) and Client mode (CM). To operate in Client Mode, a WiFi router must be located within the range of the Device. Shelly® devices can communicate directly with other WiFi devices through HTTP protocol. An API can be provided by the Manufacturer. Shelly® devices may be available for monitoring and control even if the User is outside the range of the local WiFi network, as long as the WiFi router is connected to the Internet. The cloud function could be used, which is activated through the web server of the Device or through the settings in the Shelly Cloud mobile application. The User can register and access Shelly Cloud, using either Android or iOS mobile applications, or any internet browser and the web site: https://my.Shelly.cloud/

Technical Information

Control through WiFi from a mobile phone, PC, automation system or any other Device supporting HTTP and/or UDP protocol.
Microprocessor management.

CAUTION! Danger of electrocution. Mounting the Device to the power grid has to be performed with caution.
CAUTION! Do not allow children to play with the button/switch connected to the Device. Keep the Devices for remote control of Shelly (mobile phones, tablets, PCs) away from children. Installation Instructions
CAUTION! Danger of electrocution! The mounting/ installation of the Device should be done by a qualified person (electrician).
CAUTION! Danger of electrocution! Do not connect the current transformer clamp to the Line, before wiring it to Shelly 3EM. Even if only the current transformer is connected, there might be high voltage across its connection cables.
CAUTION! Danger of electrocution. Even when the device is turned off, it is possible to have voltage across its clamps. Every change in the connection of the clamps has to be done after ensuring all local power is powered off/ disconnected.
CAUTION! Do not connect the Device to appliances exceeding the given max load!
CAUTION! Connect the Device only in the way shown in these instructions. Any other method could cause damage and/or injury.
CAUTION! Before beginning the installation please read the accompanying documentation carefully and completely. Failure to follow recommended procedures could lead to malfunction, danger to your life or violation of the law. Allterco Robotics is not responsible for any loss or damage in case of incorrect installation or operation of this Device. CAUTION! Use the Device only with a power grid and appliances which comply with all applicable regulations. A short circuit in the power grid or any appliance connected to the Device may damage the Device.
CAUTION! Connect the current transformers accordingly for each channel! Each current transformer is marked and calibrated for the respective input of the Device. Any improper connection will lead to incorrect device measurement and visualization.

RECOMMENDATION Тhe Device may be connected to and may control electric circuits and appliances only if they comply with the respective standards and safety norms.

Initial Inclusion
Before installing/mounting the Device ensure that the grid is powered off (turned down breakers). Connect Shelly 3EM to the power grid and install it in the breakers box following the scheme that suites the desired purpose. You may choose if you want to use Shelly with the Shelly Cloud mobile application and Shelly Cloud service. You can also familiarize yourself with the instructions for Management and Control through the embedded Web interface.

Control your home with your voice
All Shelly devices are compatible with Amazon Echo and Google Home. Please see our step-by-step guide on:
https://shelly.cloud/compatibility/Alexa
https://shelly.cloud/compatibility/Assistant

The mobile application – Shelly cloud
Shelly Cloud gives you the opportunity to control and adjust all Shelly® Devices from anywhere in the world. You only need an internet connection and our mobile application, installed on your smartphone or tablet. To install the application please visit Google Play or App Store and install the Shelly Cloud app.

Registration
The first time you load the Shelly Cloud mobile app, you have to create an account that can manage all your Shelly® devices.
Forgotten Password
In case you forget or lose your password, just enter the e-mail address you have used in your registration. You will then receive instructions to change your password.
WARNING! Be careful when you type your e-mail address during the registration, as it will be used in case you forget your password. After registering, create your first room (or rooms), where you are going to add and use your Shelly devices.

Device Inclusion
To add a new Shelly device, connect it to the power grid following the Installation Instructions included with the Device.

• Step 1 – After the installation of Shelly in the breakers box and the power is turned on Shelly will create its own WiFi Access Point (AP).

WARNING! In case the Device has not created its own WiFi network with SSID like shellyem3-35FA58 check if you have connected Shelly correctly by the schemes described above. If you do not see an active WiFi network with SSID like shellyem3-35FA58, reset the Device. In order to reset the device, you will need physical access to it. On the front of the device, you will see a button. Press and hold it for 10 seconds. Shelly should return to AP Mode. If not, please repeat or contact our customer support at support@shelly.cloud
• Step 2 – Choose “Add Device”. In order to add more Devices later, use the app menu at the top right corner of the main screen and click “Add Device”. Type the name (SSID) and password for the WiFi network, to which you want to add the Device.

• Step 3 – WiFi network inclusion If using iOS press the home button of your iPhone/iPad/iPod. Open Settings > WiFi and connect to the WiFi network created by Shelly, e.g. shellyem3-35FA58. If using Android your phone/tablet will automatically scan and include all new Shelly Devices in the WiFi network that you are connected to.

Upon successful Device Inclusion to the WiFi network you will see this popup:

• Step 4 – Approximately 30 seconds after the discovery of any new Devices оn the local WiFi network, а list will be displayed by default in the “Discovered Devices” room.

• Step 5 – Enter Discovered Devices and choose the Device you want to include in your account.

• Step 6 – Enter a name for the Device (in the Device Name field). Choose a Room, in which the Device has to be positioned. You can choose an icon or add a picture to make it easier to recognize. Press “Save Device”.

• Step 7 – To enable connection to the Shelly Cloud service for remote control and monitoring, press “YES” on the following pop-up.

Shelly devises Settings
After your Shelly device is included in the app, you can control it, change its settings and automate the way it works. To switch the relay of the Device on and off, use the respective Power button. To enter the Details menu of the respective Device, simply click on its name. From the details menu, you may control the Device, as well as edit its appearance and settings.

Details menu

Here you will see the momentary:

Consumption – in Watts
Voltage -in Volts
Reactive power – in Volt-Ampere Reactive (VAR)
Power Factor – in the range of -1 to 1 Below that you will see the history graph for the last year for:
Consumption*
Voltage –with a lowest and highest measurement

*If you have connected your solar panel to Shelly 3EM, it will be shown in green color.

Settings
Timer
Manage the power supply automatically

Auto OFF: After turning on, the power supply will automatically shut down after a predefined time (in seconds). A value of 0 will cancel the timer.
Auto ON: After turning off, the power supply will be automatically turned on after a predefined time (in seconds). A value of 0 will cancel the timer.

Weekly Schedule This function requires an internet connection. Shelly receives actual information about the time of sunrise and sunset in your area. Shelly may turn on/off automatically at a predefined time, at sunrise/sunset, or at a specified time before or after sunrise/sunset.

Internet/Security

WiFi Mode – Client: This allows the device to connect to an available WiFi network. After typing the details in the respective fields, press Connect.
WiFi Client Backup: This allows the device to connect to an alternative WiFi network if the primary is not available. After typing the details in the respective fields, press Set.
WiFi Mode – Access Point: Configure Shelly to create a Wi-Fi Access point. After typing the details in the respective fields, press Create Access Point.
Cloud: Enable or Disable connection to the Cloud service.
Restrict Login: Restrict the web interface of Shely with a Username and Password. After typing the details in the respective fields, press Restrict Shelly.

Settings

Power-On Default Mode – This sets the default output state when Shelly is powered. – ON: Configure Shelly to turn ON, when it has power. – OFF: Configure Shelly to turn OFF, when it has power. – Restore Last Mode: Configure Shelly to return to last state it was in, when it has power.
Firmware Update – Update the firmware of Shelly, when a new version is released.
Time Zone and Geo-location
– Enable or Disable the automatic detection of Time Zone and Geo-location.
Factory Reset – Return Shelly to its factory default settings.
Device Information
– Here you can see the:
– Device ID
– Unique ID of Shelly
– Device IP
– The IP of Shelly in your Wi-Fi network
– Device Type
– The type of your Shelly device
– WiFi Name
– the Name (SSID) of the WiFi network to which your Shelly is connected
– WiFi Signal
– the signal strength of the WiFi network to which your Shelly has connected Edit Device From here you can edit:
Device Name
Device Room
Device Picture
When you are done, press Save Device. Some of the features of the Shelly Cloud mobile application are available at https://my.shelly.cloud/ as well.

The Embedded Web Interface
Еven without the mobile app, Shelly can be set and controlled through a browser and WiFi connection of a mobile phone, tablet, or PC. Abbreviations Used:

Shelly-ID – the unique name of the Device. It consists of 6 or more characters. It may include numbers and letters, for example, 35FA58.
SSID – The name of the WiFi network, created by the Device, for example, shellyem3-35FA58.
Access Point (AP) – the mode in which the device creates its own WiFi connection point with the respective name (SSID).
Client Mode (CM) – the mode in which the device is connected to another WiFi network.

Installation/Initial inclusion

• Step 1 – Install Shelly to the power grid following the schemes described above and place it into the console. After turning the power on Shelly will create its own WiFi network (AP).
WARNING! In case the Device has not created its own WiFi network with SSID like shellyem3-35FA58 check if you have connected Shelly correctly by the schemes described above. If you do not see an active WiFi network with SSID like shellyem3-35FA58, reset the Device. In order to reset the device, you will need physical access to it. On the front of the device, you will see a button. Press and hold it for 10 seconds. Shelly should return to AP Mode. If not, please repeat or contact our customer support at: support@shelly.cloud
• Step 2 – When Shelly has created their own WiFi network (own AP), with a name (SSID) such as shellyem3-35FA58. Connect to it with your phone, tablet, or PC.
• Step 3 – Type 192.168.33.1 into the address field of your browser to load the web interface of Shelly.

General – Home Page
This is the home page of the embedded web interface. Here you will see information about:

Total electrical consumption of all channels
Current electrical consumption, Voltage, Reactive power, and Power Factor of Channel A
Current electrical consumption, Voltage, Reactive power, and Power Factor of Channel B
Current electrical consumption, Voltage, Reactive power, and Power Factor of Channel C
Power Button
Connection to Cloud
Present time
Settings
Shelly 3EM can store in his internal memory history for 365 days. You can download it in .xml format by clicking the download button next to the channel info.

Timer
To manage the power supply automatically, you may use:

Auto OFF: After turning on, the power supply will automatically shut down after a predefined time (in seconds). A value of 0 will cancel the timer.
Auto ON: After turning off, the power supply will be automatically turned on after a predefined time (in seconds). A value of 0 will cancel the timer. Weekly Schedule This function requires an internet connection. Shelly receives actual information about the time of sunrise and sunset in your area. Shelly may turn on/off automatically at a predefined time, at sunrise/sunset, or at a specified time before or after sunrise/ sunset.

Internet/Security

WiFi Mode – Client: Allows the device to connect to an available
WiFi network. After typing the details in the respective fields, press Connect.
WiFi Client Backup: This allows the device to connect to an alternative WiFi network if the primary is not available. After typing the details in the respective fields, press Set.
WiFi Mode – Access Point: Configure Shelly to create a Wi-Fi Access point. After typing the details in the respective fields, press Create Access Point.
Restrict Login: Restrict the web interface of Shelly with a Username and Password. After typing the details in the respective fields, press Restrict Shelly.
SNTP Server: You can change the default SNTP server. Enter the address, and click Save.
Advanced – Developer Settings: Here you can change the action execution: – Via CoAP (CoIOT) – Via MQTT
Cloud: Enable or Disable connection to the Cloud service.

Settings

Power-On Default Mode
– This sets the default output state when Shelly is powered.
– ON: Configure Shelly to turn ON, when it has power.
– OFF: Configure Shelly to turn OFF, when it has power.
Restore Last Mode – Configure Shelly to return to the last state it was in when it has power.
Firmware Update – Update the firmware of Shelly, when a new version is released.
Time Zone and Geo-location
– Enable or Disable the automatic detection of Time Zone and Geo-location.
Set Date/Time – You can manually set the date and time for your Shelly device.
Factory Reset – Return Shelly to its factory default settings.
Device Reboot – Reboots the device.
Device Info – Shows your device ID. In Client, Mode shows also your WiFi network name and WiFi signal strength.

Description of Shelly 3EM values:

Power Consumption – This is the power that is actually consumed or utilized in an AC Circuit. It is also called True power, Active power, or Real power. It is measured in kilowatt (kW) or megawatt (MW). It is the actual outcome of the electrical system which runs the electric circuits or loads. This is the energy which you are paying. It is shown separately with individual colors for each phase, in the history graph. If you have solar panels and sell energy, you will see this power with a “negative” value. It is shown in green color in the history graph.
Reactive power – This is the power that flows back and forth, it moves in both the direction in the circuit or reacts upon itself. The Reactive power is measured in Volt-Ampere reactive (VAR), Kilo Volt-Ampere reactive (VAR) or Mega Volt-Ampere reactive (MVAR). You are not being charged for this energy.
Power Factor – The power factor of an AC electrical circuit is defined as the ratio of the real power absorbed by the load to the apparent power flowing in the circuit, and is a dimensionless number in the closed interval of −1 to 1. A power factor of less than 1 indicates the voltage and current are not in phase, reducing the instantaneous product of the two. In a perfect situation, the Power Factor is close to 1.
Voltage – Voltage, also called electromotive force, is a quantitative expression of the potential difference in charge between two points in an electrical field.

You can download your history by going to https://my.shelly.cloud/ in a browser on a PC.

Manufacturer: Allterco Robotics EOOD
Address: Sofia, 1407, 103 Cherni Vrah Blvd.
Tel.: +359 2 988 7435
E-mail: support@shelly.cloud
Web: http://www.Shelly.cloud

The Declaration of Conformity is available at: https://Shelly.cloud/declaration-of-conformity/
Changes in the contact data are published by the Manufacturer at the official website of the Device: http://www.shelly.cloud The User is obliged to stay informed of any amendments of these warranty terms before exercising his/her rights against the Manufacturer.

All rights to trademarks of Shelly®, and other intellectual rights associated with this Device belong to Allterco Robotics EOOD.

Shelly Eye B07CP2K8J9 3G & WiFi Smart Camera Manual

ItsManual — Tue, 27 Jun 2023 10:03:06 +0000

Shelly Eye B07CP2K8J9 3G & WiFi Smart Camera User Guide

Overview

The smart camera with 3G & WiFi, Shelly Eye by Allterco Robotics streams live video, saves
videos on Cloud or SD. Shelly Eye can send motion and audio detected alerts, hear and respond with two-way audio and the integrated battery provides up to a 24h of recording without power supply. Shelly may work as a standalone Device or as an accessory to She ® or other home automation controller.

Specification

Camera Sensor: 1MP CMOS
Resolution:
• HD – 1280×720 p
• WVGA – 640×352 p
Camera Lens:
• Aperture – F2.2
• Angle – 110° wide
Video:
• Compression format – H.264
• FPS – max 30
Audio Format: G.711 (16 bit/8 KHz)
3G: WCDMA (band 1, 2, 5, 8)
WiFi:
• Protocol: 802.11 b/g/n
• Frequency: 2.4 GHz
WiFi Operational range (depending on local construction):
• up to 30 m outdoors
• up to 10 m indoors
Motion detection
• Angle – 120°
• Range – up to 5 m
Power supply: 5V/2A DC
Power consumption: < 5W
Battery: Li-Ion 1000mAh
Battery life: Up to 24 hours
Memory: SD Card (up to 32GB)*
Working temperature: -20 ÷ 50°C
Dimensions (HxD):
Device – 122 x 41 x 40 mm
Stand – 34 x 41 x 39 mm
Device & Stand – 150 x 41 x 40 mm
*Memory card not included
Buttons and indicators
Button:
• Turn on – hold, when the device is off
• Turn off – hold, when the device is on

Technical information

CAUTION! Keep the remote control devices (mobile phones, tablets, PCs) away from children.

CAUTION! Use the Device only with power grid which complies with all applicable regulations. In case Shelly Eye is connected to the power grid and a short circuit occurs, it may damage the Device.

The Shelly Eye Mobile Application

Shelly Eye app gives you the opportunity to control and adjust all Shelly® Eye Cameras from
anywhere in the world. All you need is an Internet connection and our mobile application,
installed on your smartphone or tablet.

Initial Set-Up

The first time you open the Shelly Eye mobile app, you have to create an account to manage
your Shelly Eye® cameras.

Registration

Download and install the Shelly Eye mobile application. To install the application scan the
QR code on the box, or please visit Google Play (Android) or App Store (iOS).
Open the app and create an account by clicking on the Register button (fig. 3)
Input e-mail and password
Validate your account
Open the app again and press on the Sign In button.

Forgotten Password

In case you forget or lose your password, just enter the e-mail address you have used in your registration. You will then receive instructions on how to change your password.

fig. 3

WARNING! Be careful when you type your e-mail address during the registration, as it will be used in case you forget your password.

Device Inclusion
To add a new Shelly camera, connect it to the power grid.

Step 1
Choose “Add Device” – fig. 4.

In order to add more Devices later, use the app menu at the top right corner of the main screen
and click “Add Device”.

Step 2
You will see the following screen – fig. 5

Scan the QR code placed on Shelly Eye. Upon successful scan of the code, the UUID of the
Device will be shown below the QR code frame. Press the tick sign at the top right of the
screen.

Step 3:
Select the Setup Mode (fig. 6):

Mode 1 – If you have not inserted a SIM card, and you hear a voice prompt when the
Device boots up, press on Voice Prompt
Mode 2 – If you have inserted a SIM card, press on No Voice Prompt

WARNING: In case the Device has not prompted with “Waiting for connection”, or
you want to add the Device to another Wi-Fi network, reset it. To reset the Device press the button 10 consecutive times, then the LED will turn purple. After that the Device will restart. If not, please repeat or contact our customer support at: support@shelly.cloud

MODE 1

Wi-Fi
Step 1:
When you hear the voice prompt you have to enter the Name (SSID) and password of your
WiFi network (fig. 7).

Step 2:
You will see a tip on how to proceed (fig.8)

Step 3:
You will hear a voice prompt to scan the QR code on your phone with Shelly Eye. Place the screen of your phone in front of Shelly Eye and wait for the camera to scan the QR code (fig. 9).

Step 4:
Press Next when you hear the voice prompt that Shelly has scanned and connected successfully.

Step 5:
Your Shelly Eye will connect to your WiFi and will be added to your account (fig. 10).

Step 6:
You will hear the voice prompt that Shelly has connected successfully. Press on “Start Using”
(fig. 11).

MODE 2

3G
Step 1:
Press on “No voice prompt” (fig. 6)

Step 2:
Your Shelly Eye will connect through mobile data and will be added to your account (fig. 10).

Step 3:
You will hear the voice prompt that Shelly has connected successfully. Press on “Start Using”
(fig. 11).

Warranty Terms

The Device’s warranty term is 24 (twenty four) months, beginning since the date of
purchase by the End User. The Manufacturer is not responsible for extra warranty terms by
the Еnd Seller.
The Warranty is valid for the territory of EU. The warranty is applicable in compliance with all relevant laws and users’ rights protections. The purchaser of the Device is entitled to exercise his/her rights in accordance with all applicable laws and regulations.
Warranty terms are provided by Allterco Robotics EOOD (referred hereinafter as the Manufacturer), incorporated under the Bulgarian law, with address of registration 109 Bulgaria Blvd, floor 8, Triaditsa Region, Sofia 1404, Bulgaria, registered with the Commercial Register kept by the Bulgarian Ministry of Justice’s Registry Agency under Unified Identity Code (UIC)
202320104.
Claims regarding the Conformity of the Device with the terms of the contract of sale shall
be addressed to the Seller, in accordance with its terms of sale.
Claims regarding damages such as death or body injury, deterioration or damages to objects different from the defective product, caused by a defective product, are to be claimed against the Manufacturer using the contact data of the Manufacturer’s company.
The User may contact the Manufacturer via e-mail at support@shelly.cloud for operational
problems that may be resolved remotely. It is recommended that the User contact the
Manufacturer before sending the Device for servicing.
The terms of removing defects depends on the commercial terms of the Seller. The
Manufacturer is not responsible for untimely servicing of the Device or for faulty repairs
carried out by unauthorized service.
When exercising their rights under this warranty, the User must provide the Device with the
following documents: receipt and valid warranty card with date of purchase.
After a warranty repair has been carried out, the warranty period is extended for that period.
The warranty does NOT cover any damages to the Device which occur in the following
circumstances:

When the Device has been used or wired inappropriately, including electric shock, short
circuit or other problems in the power supply, the power grid or the radio network.
When there has been a self-repair attempt, faulty (de)installation, modification, or readjustment of the Device by unauthorized persons.18
Intentional or negligent improper handling, storing or transportation of the Device, or in the event of non-observance of the instructions included in this warranty.;
When a non-standard power supply, network, or faulty Devices have been used;
When there is a non-compliance between warranty card and/or without a purchase receipt,
or attempted forgery of these documents, including (but not limited to) the warranty card
or the documents proving the purchase.
When damages occur which were caused regardless of the Manufacturer, including but
not limited to: floods, storms, fire, lightning, natural disasters, earthquakes, war, civil wars,
other force majeure circumstances, unforeseen accidents, robbery, water damage, any
damages made by ingress of liquids, weather conditions, solar heating, any damages
caused by intrusion of sand, humidity, high or low temperature, or air pollution.
When there are other reasons beyond manufacturing defect, including but not limited to:
water damage, ingress of liquid into the Device, weather conditions, solar overheating,
intrusion of sand, humidity, low or high temperature, air pollution.
When there have been mechanical damages (forced opening, breaking, cracks, scratches
or deformations) caused by a hit, fall, or from another object, wrong use, or caused by not
following the instructions for use.
When damage has been caused by exposing the Device to severe outdoor conditions
such as: high humidity, dust, too low or too high temperature. Terms of proper storage are
specified in the User Manual.
When damage has been caused by faulty accessories, or those not recommended by the
Manufacturer.
When damage has been caused by the use of non-original spare parts or accessories not
suitable for the specified Device model, or after repairs and changes carried out by an
unauthorized service or person.
When damage has been caused by the use of faulty Devices.
When damage has been caused by faulty software, a computer virus or other harmful
behavior on the Internet, or by lack of software updates or incorrect updates by a method
not provided by either the Manufacturer or by the Manufacturer’s software.

11. The range of warranty repairs does not include periodical maintenance and inspections, particularly cleaning, adjustments, checks, bug fixes or program parameters and other activities that must be performed by the User (Buyer). The warranty does not cover wear of the Device, because such elements have a limited lifespan.

12. The Manufacturer is not responsible for any property damage caused by a defect in the Device. The Manufacturer is not liable for indirect damages (including but not limited to loss
of profits, savings, lost profits, claims by third parties) in connection with any defect of the Device, nor for any property damage or personal injury arising out of or related to the use of the Device.

13. The Manufacturer is not responsible for damage caused by circumstances independent of
the Manufacturer, including but not limited to: floods, storms, fire, lightning, natural disasters,
earthquakes, war, civil unrest and other force majeure, unforeseen accidents, or theft.

Safety Usage

Never use the device at temperatures lower than 0° C and higher than 40° C. Use the Device only at a temperature between 0° C and 40° C. Exposing the Device to lower or
higher temperatures may damage it or potentially harm your health.
Do not expose the Device to direct sunlight for long periods of time.
Do not expose the Device or its components to an open flame or throw it into fire.
Do not throw, scratch or drop the Device. It is NOT shockproof.
Always clean the Device with a dry cloth
Do not expose the Device to moisture/liquids as a whole or its components, including the
battery. Do not use it under water! Do not use the Device if it has been wet. The device is
NOT waterproof.
Do not use any cleaning products or chemicals! They can damage the Device!
Do not place the Device directly on sand.
In case your child breaks the Device, gather the parts and do not allow your child to
swallow any of them. Small parts can cause suffocation or injuries.
Always remove the charger from the outlet, after fully charging the battery of the Device.
Do not allow children to charge the battery.
Do not connect faulty USB cables and chargers to the Device.
Do not manipulate the battery. Improper use of the battery may result in fire and even
explosion.
Do not attempt to broach the design and/or components of the Device (including the
battery) or modify them.
Do not open, hit, step on or violate the integrity of the Device.
Do not interfere with the integrity of the USB power cable. Do not twist it, do not tear it, do not bite it, do not pull it, cut it or violate its integrity.
Avoid contact with magnets.