Depository Safes

OWNERS MANUAL

Thank you for purchasing this security safe from Sentry®Safe. This guide is designed to maximize the user and security features of this project.

Getting started

Installation of the batteries (keep the door open during setup):

1. Turn the keypad housing counterclockwise and carefully pull away from the mounting plate to expose the battery compartment.
2. Install four new AAA Alkaline batteries (not included). Caution: Hold onto the keypad housing to avoid pulling wires.
3. Carefully position the keypad into the inserts on the mounting plate and turn clockwise. Ensure that there are no wires or cables trapped between the keypad and the mounting plate. Pinched cables result in a short circuit.
4. Enter: * – Master or Manager Code (from the front of the booklet) – # The lock will indicate a valid code entry with a single signal and the open light will stay green for five (5) seconds.
5. Turn the handle clockwise before the green light disappears.

Programming your lock codes

The SentrySafe electronic lock is shipped from the factory with a factory set master code & manager code (see the front of the booklet). You should set the lock to your own unique master & manager code immediately. Keep notes on which code belongs to which user (Master (User 1), Manager (User 2), User 3, User 4, User 5, User 6 and User 7).

A single signal (LED fl ashes and beeps once) response from the lock indicates valid entry.

A double signal (LED fl ashes and beeps twice) response from the lock indicates an invalid entry.

• If three incorrect entries are entered in a row, the keypad will shut down for a period of fi ve minutes. During this shut down period you will not get a response from the keypad.

Changing the Master Code

(Code length: 1 to 10 digit code) Always perform this operation with the door open.

1. Enter: # – Existing Master Code – #
2. The set light will stay orange for ten (10) seconds.
3. Enter: 1 – * – New Master Code – # – New Master Code – #, before the orange light disappears.

If a mistake is made during the change, wait thirty (30) seconds and repeat steps 1 thru 3.

Test the new code several times before closing the door: Enter: * – Code – #

• The lock will indicate a valid code change with a single signal.
• The lock will indicate an invalid code change with a double signal and the old code is still valid.

Changing the Manager Code

(Code length: 1 to 10 digit code) Always perform this operation with the door open.

1. Enter: # – Master Code or Manager Code – #
2. The set light will stay orange for ten (10) seconds.
3. Enter: 2 – * – New Manger Code – # – New Manager Code – #, before the orange light disappears.

If a mistake is made during the change, wait thirty (30) seconds and repeat steps 1 thru 3. Test the new code several times before closing the door: Enter: * – Code – #

• The lock will indicate a valid code change with a single signal.
• The lock will indicate an invalid code change with a double signal and the old code is still valid.

Activate user codes

(Code length: 1 to 10 digit code) Always perform this operation with the door open.

1. Enter: # – Master Code or Manager Code – #
2. The set light will stay orange for ten (10) seconds.
3. Enter: User ID Number (3-7) – * – New User Code – # – New User Code – #, before the orange light disappears.

If a mistake is made during the activation, wait thirty (30) seconds and repeat steps 1 thru 3.

• The lock will indicate a valid code entry with a single signal.
• The lock will indicate an invalid code entry with a double signal and the old code is still valid.

Example: # – Master Code or Manger Code – # – 5 – * – New User Code – # – New User Code – #. This will activate User Five (5).

Changing the user code

Always perform this operation with the door open

1. Enter: # – User Code – #
2. The set light will stay orange for ten (10) seconds.
3. Enter: New User Code – # – New User Code – #, before the orange light disappears.

If a mistake is made during the change, wait thirty (30) seconds and repeat steps 1 thru 3.

Test the new code several times before closing the door: Enter: * – Code – #

• The lock will indicate a valid code change with a single signal.
• The lock will indicate an invalid code change with a double signal and the old code is still valid.

The Master and Manager can also change the user codes by following the “Activate user codes” section steps 1 thru 3.

Deleting user codes

Always perform this operation with the door open.

1. Enter: # – Master Code or Manager Code – #
2. The set light will stay orange for ten (10) seconds.
3. Enter: User ID Number (3-7) – * – # – #

Dual user mode

When you want two people to open the safe; set your safe to dual user mode. One person enters their code and within sixty (60) seconds, the second code is entered. Always perform this operation with the door open.

Any Code + Any Code to unlock

1. Enter: # – Master Code – # – 1 – # – 1 – #
2. The lock will indicate a valid setting change with a single signal.

Master or Manager Code + User Code to unlock

1. Enter: # – Master Code – # – 2 – # – 2 – #
2. The lock will indicate a valid setting change with a single signal.

Opening your safe in dual user mode

1. Enter: * – 1st Code – # – 2nd Code – #
2. The lock will indicate a valid code entry with a single signal and the open light will stay green for fi ve (5) seconds.
3. Turn the handle clockwise before the green light disappears

Returning to single user mode (Single code to unlock)

1. Enter: # – Master Code – # – 0 – # – 0 – #
2. The lock will indicate a valid setting change with a single signal.

Time delay mode

Always perform this operation with the door open. This function will delay both the opening and programming of the lock.

Activate time delay

1. Enter: # – Master Code – # – (01-99) – # – (01-99) – #
2. The lock will indicate a valid setting change with a single signal. Example: # – Master Code – # – 05 – # – 05 – #, this will set a fi ve (5) minute time delay.
3. Press * or # to initiate the Time Delay.

When time delay is set

(During the time delay period the keypad will not respond to any entries)

The lock will flash once every five (5) seconds during time delay and will flash once every second during the last ten (10) seconds of the time delay ending with a double signal.

The lock will flash twice every five (5) seconds during the open period. The open period length is two (2) minutes.

During the open period, you can open your safe (see “How to open your safe, Step 1) or program your safe (following the steps of any programming procedure).

Deactivate time delay

1. Enter: # – Master Code – # – 00 – # – 00 – #
2. The lock will indicate a valid setting change with a single signal.

Floor Mount (optional)

This kit contains:

• Four (4) Masonry Anchors

Required tools:

• Powered Drill
• Adjustable Wrench
• 1/2 in. (M12) Masonry Drill

Instructions:

1. Unlock safe and open door.
2. Remove safe floor carpet.
3. Look on the bottom of safe for four (4) holes with cap plugs.
4. Remove the cap plugs.
5. Position the safe in the desired location.
6. From inside the safe mark the location of the four (4) bolt down holes.
7. Move the safe aside to the clear marked spots for drilling.
8. Using the ½ in. masonry drill, drill a 4 in. deep hole in the marked locations.
9. Replace the safe in the desired location with the holes in the safe aligned with the
   drilled holes in the floor.
10. Pass each masonry anchor through the safe floor into the drilled holes; making contact with the safe floor.
11. Tighten each masonry anchor with the adjustable wrench.
12. Replace safe floor carpet.

Customer Care

Troubleshooting

Low battery warning

The green LED light will signal in red when opening your safe. The lock is giving you a valid signal but is not unlocking.

Changing your batteries

1. Turn the keypad housing counterclockwise and carefully pull away from the mounting plate to expose battery compartment.
2. Remove the four AAA Alkaline batteries and replace. Caution: Hold onto the keypad housing to avoid pulling wires.
3. Carefully position the keypad into the inserts on the mounting plate and turn clockwise. Ensure that there are no wires or cables trapped between the keypad and the mounting plate. Pinched cables result in a short circuit.

The lock has no response (no fl ash, no beeps)

• Make sure the wires in the keypad housing are not pinched and are securely connected. (See “installation of batteries” on page 2)
• Check to make sure the batteries are correctly and securely inserted into the battery compartment. (See “installation of batteries” on page 2)
• Lock can possibly be in the lockout penalty, wait fi ve (5) minutes, and check if the lock responds.
• Replace the existing batteries with new ones. (See “changing your batteries” in troubleshooting)

The lock is responding but does not unlock

• Make sure you are getting a valid response.
• Make sure you get a signal with every key stroke.
• Make sure you are not in time delay mode. (See “time delay mode” above)
• Replace the existing batteries with new ones. (See “changing your batteries” in troubleshooting)

If the lock still does not open, contact Sentry Group Customer Care: 1-800-828-1438 or 585-381-4900 (Available Mon – Fri, 8:00 am – 6:00 pm EST). Follow the instructions carefully to get the best possible use from your lock.

SentrySafe Fire-Safe Electronic Lock

IMPORTANT

If you experience any problems or challenges with your safe, please contact us. Many issues can be resolved quickly without the product being returned.

www.sentrysafe.com
Customer Service: 1-800-828-1438
Fax: 585-381-2940
900 Linden Avenue
Rochester, New York 14625
14625-2784 USA

Getting started

Congratulations on your purchase of a Sentry®Safe product. SentrySafe is the world’s leader in
fire/water-resistant and security storage. This guide describes how to easily set up your safe.

1. Gain entry with the combination lock

Opening your safe for the fi rst time (keep door open during setup):

The handle should be all of the way UP, in the horizontal position before attempting to dial out safe.

Testing your combination: Your safe’s combination is printed on the front of this owner’s manual. You will have a 3-number or 4-number combination depending upon the model purchased.

3-NUMBER COMBINATION
(Cannot be changed)

1. To unlock and open
Before dialing your combination, simply insert the key (if equipped) in the lock and turn until the plunger pops out. Remove key.

NOTE: The safe will lock if key lock cylinder is pressed in with or without key.

• Start the dial at zero.
• Turn the dial to the left. Make sure ZERO passes the pointer at least THREE times. Then stop at the first number of your combination.
• Turn the dial to the right. Stop the SECOND time you reach the second number of your combination.
• Turn the dial to the left. Stop the FIRST time the pointer reaches the third number of your combination.

2. To close and lock
You can relock the safe in two ways. With the door closed, depress the key lock (if equipped) with your finger, or spin the combination dial one full turn. For greatest security, do both. (Make sure the door handle is in the horizontal position.)

4-NUMBER COMBINATION
(Cannot be changed)

1. To unlock and open
Before dialing your combination, simply insert the key (if equipped) in the lock and turn until the plunger pops out. Remove key.

•  Point the dial to zero.
• Turn the dial to the left. Make sure ZERO passes the pointer at least FOUR times. Then stop at the first number of your combination.
• Turn the dial to the right. Stop the THIRD time you reach the second number of your combination.
• Turn the dial to the left. Stop the SECOND time you reach the combination’s third number.
• Turn the dial to the right. Stop the FIRST time you reach the last number of your combination.

2. To close and lock
You can relock the safe in two ways. With the door closed, depress the key lock (if equipped) with your finger, or spin the combination dial one full turn. For greatest security, do both. (Make sure the door handle is in the horizontal position.)

2. Gain entry with the basic electronic lock

The handle should be all of the way UP, in the horizontal position before attempting to open safe.

Opening your safe for the first time (keep door open during setup):

1. Remove and discard the screw (if equipped) at the base of the lock case.
2. Turn the electronic lock case to the right (clockwise), from 12 o’clock to 2 o’clock, and remove.
   • Insert 4 new AA batteries (not included) to power this lock.
   • Replace the electronic lock case and turn to the left (to 12 o’clock) to reassemble.
   NOTE: The yellow LED will light when the batteries need to be replaced.
3. Turn the key (if your safe is equipped with a key lock) to the right so the lock cylinder pops out.
4. Enter the factory code (printed on the fi rst page of this guide). When the green light appears, you have four seconds to turn the handle down to open. Try this several times before proceeding to the next step.

To unlock safe:
Enter the 5-digit factory code, a pre-programmed user code, or a pre-programmed user pin (programming instructions to follow). When the green LED lights you have 4 seconds to turn the handle and open the safe.

To lock safe:
Close the door and return the handle to the horizontal position. For greatest security, depress the key lock (if equipped) with your finger.

NOTE: If your unit is equipped with a water resistant gasket additional pressure to the left corner of the door may be required before the handle can be returned to the horizontal position.

Access codes
There are 3 possible ways to unlock and access the safe:

1. Factory code
   (Found on the fi rst page of this guide) You can always open the safe by entering the pre-set 5-digit factory code. This code cannot be deleted.
2. User code
   If you prefer to employ your own code, you can program the safe to open using a 5-digit user code of your choice.
3. User pin
   If you wish to give someone else temporary access to the safe, you can program a 5-digit user pin that can later be erased.

Programming the user code
NOTE: One (1) user code is allowed.

To add:

1. Press the Prog key , then enter the 5-digit factory code.
2. Enter the 5-digit user code of your choice.

To delete:

1. Press the Prog key.
2. Enter the 5-digit factory code twice.

Programming user pin
NOTE: One (1) user pin is allowed.

To add:

1. Press the Prog key 2 times.
2. Enter your 5-digit user code.
3. Enter the 5-digit user pin of your choice.

To delete:

1. Press the Prog key 2 times.
2. Enter your 5-digit user code.
3. Enter 0, 0, 0, 0, 0.

NOTE: If your safe does not appear to be working, please check batteries before calling Sentry Customer Care.

Signals
Your electronic-lock safe communicates by means of several audio/visual signals.

Red (Error) LED + three beeps indicates one of the following:

1. You have pressed Program key out of sequence.
2. You have entered an invalid code or user pin.
3. You have let 5 seconds or more elapse between key presses.
4. Lights after three consecutive invalid codes are input (2-minute delay mode).

Green LED only:

1. Comes ON after you enter a valid code and remains lit during the 4-second period in which the safe can be opened.
2. Comes ON in the Programming mode and remains lit until you have finished entering a 5-digit code.

Yellow LED only:
1. Comes ON when the batteries need to be replaced.

3. Gain entry with advanced electronic lock

Opening your safe for the first time (keep door open during setup):

1. Remove and discard the screw (if equipped) at the base of the lock case.
2. Turn the electronic lock case to the right (clockwise), from 12 o’clock to 2 o’clock, and remove.
   • Insert 4 new AA batteries (not included) to power this lock.
   • Replace the electronic lock case and turn to the left (to 12 o’clock) to reassemble.
3. Turn the key (if your safe is equipped with a key lock) to the right so that the lock cylinder pops out.
4. Enter the factory code (printed on the fi rst page of this guide), then press the Prog/Enter key. When the unlocked padlock icon   ( ) appears, you have four seconds to turn the handle down to open. Try this several times before proceeding to the next step.

To unlock safe:
Enter the 5-digit factory code, a pre-programmed manager code, or a pre-programmed user code (programming instructions to follow), then press the Prog/Enter key. When the unlocked padlock icon ( ) appears, you have four seconds to turn the handle down to open.

To lock safe:
Close the door and return the handle to the
horizontal position. For greatest security, depress the key lock (if equipped) with your finger.

NOTE: If your unit is equipped with a water resistant gasket. Additional pressure to the left corner of the door may be required before the handle can be returned to the horizontal position.

Battery replacement
The battery icon ( ) will light when the batteries need to be replaced. No codes are erased when old batteries are removed for replacement. See “Opening your safe for the first time”.

NOTE: If your safe does not appear to be working, please check batteries before calling Sentry Customer Care.

Icon identification
(Error) indicates one of the following:

1. You have pressed Program key out of sequence.
2. You have entered an invalid code.
3. You have let 5 seconds or more elapse between key presses.
4. You have pressed a key while in delay mode.

(Program) Lights after pressing the Program key and stays lit while programming a manager or user code.

(Delay Mode) Lights after three consecutive invalid codes are input and stays lit during the 2-minute delay mode.

Access codes
There are 3 possible ways to unlock and access the safe:

NOTE: Maintain a record of the factory code, user, and manager codes, and store them in a secure location other than in this safe.

1. Factory code
   (Found on the fi rst page of this guide) You can always open the safe by entering the pre-set 5-digit factory code. This code cannot be deleted.
2. Manager code
   If you prefer to employ your own code, you can program the safe to open to a 4-8 digit manager code of your choice.
3. User code
   If you wish to give someone else temporary access to the safe, you can program a 4-8 digit user code that can later be erased.

NOTE: Remember, once you have decided on your access codes, open the unit fi rst then test it with the door open. All zeros is an invalid code.

Programming the manager code
NOTE: One (1) manager code is allowed.

To add:

1. Press the Prog/Enter key , then enter the 5-digit factory code and then press the Prog/Enter key .
2. An empty lit box icon ( ) means no manager code is programmed. A boxed lighted * icon ( ) means a manager code is programmed.
3. Enter a 4 to 8 digit code and press the Prog/ Enter key to finish programming the code into the unit.

To delete:

1. Press the Prog/Enter key, then enter the 5-digit factory code and then press the Prog/Enter key.
2. A boxed lighted * icon ( ) indicates there is a code programmed and can be deleted.
3. Press 0, 0, 0, 0, then the Prog/Enter key to delete the manager code. (0, 0, 0, 0, Prog/ Enter).

NOTE: To return to the beginning when programming a manager or user code, wait 5 seconds and the lock will time-out. You may then start over.

Programming user code
NOTE: Six (6) user codes are allowed.

To add:

1. Press the Prog/Enter key 2 times, enter the manager code and then press the Prog/Enter
   key.
2. Use the << or >> to scroll between the lighted boxes. An empty box icon ( ) means it is available for a code entry; a boxed lighted * icon ( ) means it is being used.
3. Enter a 4 to 8 digit code in the selected position and press the Prog/Enter key to finish.

To delete:

1. Press the Prog/Enter key 2 times, enter the manager code and then press the Prog/Enter key.
2. Use the << or >> to scroll to the boxed lighted * icon ( ) to be removed.
3. Press 0, 0, 0, 0, then the Prog/Enter key to delete the selected user. (0, 0, 0, 0, Prog/Enter).

NOTE: To turn the beeper on or off, press the 0 key and then the Prog/Enter key. (0, Prog/Enter).

4. Floor Mount (optional)

Optional kit (Fig. A) contains
(included on select models only):

• (2) Lag screws
• (2) Washers
• (2) Masonary anchors

Tools needed for floor mounting:

• Drill
• Wrench
• 7⁄16″ (11.0 mm) drill bit

Wood anchoring:
9⁄32″ (7.2 mm) drill bit

Masonry anchoring:
3⁄8″(9.50 mm) drill bit

Instructions:

1. Tip the safe onto its right side. (Door hinges horizontal with the floor.)
2. Unlock the safe and open the door.
3. Look on the bottom of the safe for two indentations on the feet in opposite corners. Using the 7⁄16″ (11.0 mm) bit, drill a hole through each indentation perpendicular to the bottom of the safe (Fig. B). Do not drill from any location inside the safe. 
4. Close the door and tip the safe upright. Place it where desired and reopen the door.
5. Use a screw or drill bit to mark the floor through both holes. (Fig. C)
6. Move the safe aside to clear both marked spots for drilling.
7. Drill into the floor:                                                                 
   A. For wood: Using the wood drill bit, drill a hole 2-1⁄2″ (64 mm) deep in each marked spot. (Fig. D)
   B. For masonry: Using the masonry bit, drill a hole 2-1⁄2″ (64 mm) deep in each marked spot. (Fig. D) Install a masonry anchor in each hole.
8. Replace the safe in the desired position, with the holes in the safe aligned with those in the floor.
9. Securing the safe:
   A. For wood: Pass each lag screw through a washer, then through the safe and into a hole. Tighten with the wrench. (Fig. E)                                      
   B. For masonry: Pass each lag screw through a washer, then through the safe and into a masonry anchor. Tighten with the wrench. (Fig. F)          

NOTE: Drill holes through feet only, not through the back or sides. Bolting/unbolting of the unit is at the consumers expense and discretion. Sentry Group is not responsible for any costs incurred if the unit is to be replaced.

If you lose your combination/keys or need accessories, we can help!
Visit our website at www.sentrysafe.com

Please note: Your safe’s serial number is required to obtain replacement combination/keys. The serial number can be found near the door hinge as shown or at the beginning of this guide.

Delay mode
Enters a two-minute delay mode after an invalid code has been entered three consecutive times. In this mode, the lock can not be activated and any key entry will generate an ERROR signal.

Troubleshooting

• If electronics are not functioning, replace batteries first (behind electronic lock case) as described in step one of this guide.
• If electronics are functioning and you cannot get into safe:
  – Pull handle up
  – Follow instructions for opening your lock type.
• You must use both the key (if equipped) and the electronic code to open the safe if the key lock cylinder is pushed in.

Registration: To be eligible for warranty coverage, the original purchaser must register the product online at www.sentrysafe.com or complete and return to Sentry Group the enclosed registration card.

WARNING
DO NOT store delicate items directly in your safe.

SentrySafe products which offer fire protection have a proprietary insulation that has a high moisture content. In addition the SentrySafe advanced safes close airtight to offer water resistance, which may also cause moisture to accumulate inside your safe. The desiccant packet included in your safe during shipment, should be left in your safe. DO NOT DISCARD IT. It is intended to help absorb moisture which may accumulate inside your safe. Please open your unit periodically to avoid moisture accumulation.

If you choose to store delicate items such as jewelry with working parts, watches, stamps, or photos in your safe, we recommend putting them in an air-tight container, prior to placing them in the safe for storage.

NOTE: Sentry Group will not be responsible for any damage or loss of items placed in the unit due to moisture.

WARNING
DO NOT store pearls in this safe unit.
In the event of a fire, potential damage to delicate pearls occurs at temperatures much lower than the 350°F interior performance measure which the UL classification performance standard indicated guarantees. Therefore, DO NOT store pearls in your SentrySafe product.

WARNING
No computer disks, audio-visual media or photo negatives.
This product is not intended to protect computer floppy or diskettes, cartridges and tapes, audio or video cassettes or photo negatives. For fire-resistant storage of these materials, ask your retailer for the SentrySafe Fire-Safe Media storage products.

Rigorous testing ensures this product meets our specifications

ETL Verified Water-Resistance Protection (if equipped)
Tested up to 8 inches of water for up to 24 hours.
Note: Maximum allowable leakage is 170 grams.

NOTE: For the gasket to work effectively, the safe door must be closed with the handle fully horizontal. When you move the handle, the compression of the gasket will require slightly more force than you would use with a safe that does not have a gasket.

User Manual

SentrySafe Fire-Safe Combination/Keypad

Warnings

WARNING
Gun warning: This product is not intended for the secure storage of all materials. Items such as
firearms, other weapons, combustible materials, or medication should NOT be stored in this unit.

WARNING
DO NOT store delicate items directly in your safe.

SentrySafe products which offer fire protection have a proprietary insulation that has a high
moisture content. In addition the SentrySafe advanced safes close airtight to offer water resistance, which may also cause moisture to accumulate inside your safe. The desiccant packet included in your safe during shipment, should be left in your safe. DO NOT DISCARD IT. It is intended to help absorb moisture which may accumulate inside your safe. Please open your unit once every two weeks to avoid moisture accumulation.

If you choose to store delicate items such as jewelry with working parts, watches, stamps, or
photos in your safe, we recommend putting them in an air-tight container, prior to placing them in the safe for storage.

NOTE: Sentry Group will not be responsible for any damage or loss of items placed in the unit due to moisture.

WARNING
DO NOT store pearls in this safe unit. In the event of a fire, potential damage to delicate pearls
occurs at temperatures much lower than the 350°F interior performance measure which the UL
classification performance standard indicated guarantees. Therefore, DO NOT store pearls in your SentrySafe product.

WARNING
No computer disks, audio-visual media or photo negatives. This product is not intended to protect computer floppy or diskettes, cartridges and tapes, audio or video cassettes or photo negatives. For fire-resistant storage of these materials, ask your retailer for the SentrySafe Fire-Safe Media storage products.

WARNING
YOUR SAFE IS ONLY PART OF YOUR TOTAL SECURITY PROTECTION.
Sentrysafe recommends that you store your safe in closets, offices, basements, bedrooms and any
other locations that are convenient for you but out of direct line of sight from prying eyes. The location of the safe does not affect the safes’ ability to protect your valuables inside.

IMPORTANT
If you experience any problems or challenges with your safe, please contact us. Many issues can be resolved quickly without the product being returned.

Registration:

www.sentrysafe.com/customercare/register_your_product
Reasons to register

By registering your SentrySafe product you can easily retrieve forgotten codes and combinations, which would otherwise require a notary letter and payment.

By registering your SentrySafe product you can be sure that in the unfortunate circumstance of a fire you will be guaranteed your replacement safe (provided official paperwork).

Mechanical Combination Lock

NOTE: Store combination (and keys if equipped) in a secure location (other than in the safe).
NOTE: Combination can not be changed.
NOTE: SentrySafe offers a secure online location for the entry and retrieval of your combination. Go to www.sentrysafe.com and register your safe.

Preparing your safe for first time use

Warning: Test your combination several times before putting valuables inside.

Unlocking your safe

NOTE: Make sure the handle is in the horizontal position when unlocking the safe.
NOTE: If the door does not open easily, repeat steps 1-5.
NOTE: If you exert too much force on the handle, the handle will move without moving the bolts. When this happens, you will hear a ‘click.’ DO NOT be alarmed. This feature is designed to protect the bolts from being over powered by force. If this occurs, simply exert force in the
opposite direction (lifting up) until the handles ‘clicks’ back into place and repeat steps 1-5 to open your safe.

Locking your safe

Programmable Electronic Lock

NOTE: Store code (and keys if equipped) in a secure location (other than in the safe).
NOTE: SentrySafe offers a secure online location for the entry and retrieval of your code. Go to www.sentrysafe.com and register your safe.

Preparing your safe for first time use

Warning: Test your code several times before putting valuables inside.

Unlocking your safe

NOTE: Make sure the handle is in the horizontal position when unlocking the safe.
NOTE: If you exert too much force on the handle, the handle will move without moving the bolts. When this happens, you will hear a ‘click.’ DO NOT be alarmed. This feature is designed to protect the bolts from being over powered by force. If this occurs, simply exert force in the
opposite direction (lifting up) until the handles ‘clicks’ back into place and repeat steps 1-3 to open your safe.

Locking your safe

NOTE: The 5 digit factory code cannot be deleted. However, you may add and delete additional codes.
NOTE: If your safe does not appear to be working properly, please check to make sure you are using NEW alkaline batteries before contacting SentrySafe Customer Service.

Programming information

Three code options:
Factory code:
The safe will ALWAYS unlock using this 5 digit code (found on
the back of the owner’s manual). This code cannot be deleted.

User code:
A 5 digit programmable code of your choosing that can be changed or deleted.

Secondary code:
A 5 digit programmable code of your choosing that can be changed or deleted. Can only be programmed after a user code has been activated.

NOTE: The “C” key is a clear key. This can be used at anytime to clear the system and return to
standby mode – unless you are in delay mode (3 consecutive invalid entries).

Programming the user code

Only 1 user code can be programmed at a time.

To ADD a user code:

1. Press the “P” key.
2. Enter the 5 digit factory code.
3. The light will flash green and then you will have five seconds to enter your own personal user code.

To DELETE a user code:

1. Press the “P” key.
2. Enter the 5 digit factory code.
3. Enter 0,0,0,0,0.

NOTE: The electronic lock will NOT indicate that it has deleted the user code – please test the
code to make sure it has been deleted.

Programming the secondary code

Only 1 secondary code can be programmed at a time.

To ADD a secondary code:

1. Press the “P” key two times.
2. Enter the 5 digit user code.
3. The light will flash green and then you will have five seconds to enter your own personal secondary code.

To DELETE a secondary code:

1. Press the “P” key two times.
2. Enter the 5 digit user code.
3. Enter 0,0,0,0,0.

NOTE: The electronic lock will NOT indicate that it has deleted the secondary code – please test the code to make sure it has been deleted.

NOTE: Delay mode will occur if three consecutive invalid entries have been tried. This will cause the system to shutdown for two minutes. Do NOT remove the batteries to restart the
system it will only increase the length of time for the system shutdown.

Operating the Light

How to operate the light

The safe you have purchased may include a light. This is a long-lasting LED light. Not all safes
include a light.

The batteries that operate the keypad are the same batteries that operate the light. If the light in your unit does not turn on, please change your batteries. Refer to page 6 to change the batteries. The light will turn on every time you enter your code and will remain on for 30 seconds. The light duration has three options – off, 30 seconds, and 60* seconds.

To turn the light off:

1. Press the “0” button.
2. Press the “P” button.
3. Press the “3” button.

To turn the light on for 30 seconds:

1. Press the “0” button.
2. Press the “P” button.
3. Press the “4” button.

To turn the light on for 60 seconds:

1. Press the “0” button.
2. Press the “P” button.
3. Press the “5” button.

*If the light duration is 60 seconds, the battery life will lessen at a faster rate.

Bolting Down Your Safe

Bolt down instructions

Warning: DO NOT drill through bolt cups.
Warning: DO NOT bolt through the walls.
Warning: Do NOT drill from any location inside the safe.

Bolt down kit contents (in select models only):

• 2 lag screws.
• 2 washers.
• 2 masonry anchors.

Tools needed to bolt safe to the floor:

• Drill.
• Wrench.
• 7⁄16” (11 mm) drill bit – for drilling into the safe.
• 9⁄32” (7.2 mm) drill bit – for drilling into a wood floor.
• 3⁄8” (9.5 mm) drill bit – for drilling into a masonry floor.

1. Close the door. Tip the safe onto its left side (door hinges horizontal with the floor).
2. Look to the bottom of the safe for two indentations on the feet in opposite corners. Using the 7⁄16” (11 mm) bit; drill a hole through each indentation perpendicular to the bottom of the safe. Do NOT drill from any location inside the safe.
3. Tip the safe upright, place the safe in the desired location and open the door.
4. Use a screw or pencil to mark the floor through both holes.
5. Move the safe aside to clear both marked spots for drilling.
6. Drill into the floor:                                                                          A. For wood: Using the 9⁄32” drill bit, drill a hole 21⁄2” (64 mm) deep in each marked spot.
   B. For masonry: Using the 3⁄8” drill bit, drill a hole 21⁄2” (64 mm) deep in each marked spot. Install a masonry anchor in each hole.
7. Replace the safe in the desired position, with the holes in the safe aligned with those in the floor.
8. Securing the safe:                                                                                                                   A. For wood: Pass each lag screw through a washer, then through the safe and into a hole. Tighten with the wrench.                                                       
   B. For masonry: Pass each lag screw through a washer, then through the safe and into a masonry anchor. Tighten with the wrench. Place masonry anchors into the holes in the floor.

For products that do not come with a bolt down kits.
Go to www.sentrysafe.com to find recommended hardware and instructions.

Troubleshooting

Customer Service

Customer Service
www.sentrysafe.com
Customer Service: 1-800-828-1438
Fax: 585-381-2940
900 Linden Avenue / Rochester, New York / 14625-2784 USA

How to get replacement key/combo

1. Please go to our website www.sentrysafe.com to find the necessary replacement form.
   If you are unable to use a computer please call the number above or fax us for a copy of
   replacement form.
2. Find your safe’s serial number and model number. The serial number and model number are
   printed on the small label on the right side and on the door near the hinge.
3. Please fill out the form in its entirety.
4. Send the following to Sentry Group: Check or money order and replacement form. For current pricing please go to www.sentrysafe.com/customercare. If you are unable to use a
   computer please call the number above or fax us.
5. Mail to: Sentry Group, Dept. 200, 882 Linden Avenue, Rochester, NY 14625-2784, USA-OR Fax statement (notary seal must be legible) to 1-585-381-2940.

Paying by credit card:
Payment may also be made using your VISA or Mastercard credit card by phone only.
Call 1-800-828-1438 to make credit card payment. Do not fax credit card information.

NOTE: Prices subject to change without prior notification.
NOTE: Key and combination orders may be placed on a Saturday or Sunday, however, those orders will not be processed until the following work day. Our customer service center is open
Monday thru Friday, 8 AM until 6 PM.

How to order accessories

To optimize your safes’ organization consider purchasing SentrySafe accessories for your safe.
Accessories include a locking drawer, tray, shelf, and file rack. For more items please go to our
website www.sentrysafe.com/CustomerCare/Buy_Safe_Accessories or call our customer
service number 1-800-828-1438.

Guarantees & Fire Specifications

Guarantees

LIFETIME AFTER-FIRE REPLACEMENT GUARANTEE
If this SentrySafe product is damaged by fire at any time while still owned by you (the original
owner), SentrySafe will ship a replacement free of charge.

Include your name and address, the model number, a photo of the burned unit, a description of the fire, along with a copy of the fire department, insurance or police report. Please send the following information to:

Sentry Group
882 Linden Avenue
Rochester, New York 14625-2784 USA

Fire specifications

Fire Endurance:
(UL classified protection) Subjected to temperatures up to 1700°F for a duration of 1 hour, the
safe interior will remain below 350°F. This enables your safe to withstand even high temperature
exposure, as the hottest part of a fire moves through a building.

Explosion Hazard:
(UL classified protection) Subjected to a flash fire in a 2000°F furnace for 30 minutes the unit will not explode or rupture.

Fire Impact:
(ETL verified) After being heated to 1550°F the safe is dropped 15 feet onto rubble, then cooled, inverted and reheated to 1550°F for 30 minutes.

Data Protection:
(ETL verified) 1 hour fire protection of CDs, DVDs, memory sticks and USB drives up to 1700°F. This product is NOT intended to protect computer floppy or 21⁄4” diskettes, cartridges, tapes, audio or video cassettes, or photo negatives. For fire-resistant storage of these materials, ask your retailer for the SentrySafe Fire-Safe media storage products.

SentrySafe Fingerprint / Keypade Fire-Safe Manual

IMPORTANT

DO NOT RETURN SAFE TO THE STORE!

If you experience any problems or challenges with your safe, please contact us. Many issues can be resolved quickly without the product being returned.

www.sentrysafe.com

Getting started

Congratulations on your purchase of a Sentry®Safe product. SentrySafe is the world’s leader in fi re/water-resistant and security storage. This guide describes how to easily set up your safe.

1. Gain entry with the combination lock

Opening your safe for the fi rst time (keep door open during setup):
The handle should be all of the way UP, in the horizontal position before attempting to dial out safe.

Testing your combination: Your safe’s combina tion is printed on the front of this owner’s manual. You will have
a 3-number or 4-number combination depending upon the model purchased.

3-NUMBER COMBINATION (Cannot be changed)

1. To unlock and open

Before dialing your combination, simply insert the key (if equipped) in the lock and turn until the plunger pops out. Remove key.

NOTE: The safe will lock if key lock cylinder is pressed in with or without key.

• Start the dial at zero.
• Turn the dial to the left. Make sure ZERO passes the pointer at least THREE times. Then stop at the first number of your combination.
• Turn the dial to the right. Stop the SECOND time you reach the second number of your combination.
• Turn the dial to the left. Stop the FIRST time the pointer reaches the third number of your combination.

2. To close and lock
You can relock the safe in two ways. With the door closed, depress the key lock (if equipped) with your finger, or spin the combination dial one full turn. For greatest security, do both. (Make sure the door handle is in the horizontal position.)

4-NUMBER COMBINATION

1. To unlock and open
Before dialing your combination, simply insert the key (if equipped) in the lock and turn until the plunger pops out. Remove key.
NOTE: The safe will lock if key lock cylinder is pressed in with or without key.

• Start the dial at zero.
• Turn the dial to the left. Make sure ZERO passes the pointer at least FOUR times. Then stop at the first number of your combination.
• Turn the dial to the right. Stop the THIRD time you reach the second number of your combination.
• Turn the dial to the left. Stop the SECOND time you reach the combination’s third number.
• Turn the dial to the right. Stop the FIRST time you reach the last number of your combination.

2. To close and lock
You can relock the safe in two ways. With the door closed, depress the key lock (if equipped) with your finger, or spin the combination dial one full turn. For greatest security, do both. (Make sure the door handle is in the horizontal position.)

Note: Changing the combination voids your warranty. To reinstate your Limited 1-Year Warranty, (valid purchase dated receipt required) you must contact Sentry Customer Service to document your new combination. If Sentry is not notified of the combination change during the Warranty period, locksmith service fees will NOT be covered.

(For Dial safe models manufactured after 2011, use the following instructions to open your safe)

3-NUMBER COMBINATION (Cannot be changed)

1. To unlock and open
Before dialing your combination, simply insert the key (if equipped) in the lock and turn until the plunger pops out. Remove key.
NOTE: The safe will lock if key lock cylinder is pressed in with or without key.

• Start the dial at zero.
• Turn the dial to the right. Make sure ZERO passes the pointer at least THREE times. Then stop at the first number of your combination.
• Turn the dial to the left. Stop the SECOND time you reach the second number of your combination.
• Turn the dial to the right. Stop the FIRST time the pointer reaches the third number of your combination.

2. To close and lock
You can relock the safe in two ways. With the door closed, depress the key lock (if equipped) with your finger, or spin the combination dial one full turn. For greatest security, do both. (Make sure the door handle is in the horizontal position.)

4-NUMBER COMBINATION

1. To unlock and open
Before dialing your combination, simply insert the key (if equipped) in the lock and turn until the plunger pops out. Remove key.

NOTE: The safe will lock if key lock cylinder is pressed in with or without key.

• Start the dial at zero.
• Turn the dial to the left. Make sure ZERO passes the pointer at least FOUR times. Then stop at the first number of your combination.
• Turn the dial to the right. Stop the THIRD time you reach the second number of your combination.
• Turn the dial to the left. Stop the SECOND time you reach the combination’s third number.
• Turn the dial to the right. Stop the FIRST time you reach the last number of your combination.

2. To close and lock
You can relock the safe in two ways. With the door closed, depress the key lock (if equipped) with your finger, or spin the combination dial one full turn. For greatest security, do both. (Make sure the door handle is in the horizontal position.)

Note: Changing the combination voids your warranty. To reinstate your Limited 1-Year Warranty, (valid purchase dated receipt required) you must contact Sentry Customer Service to document your new combination. If Sentry is not notified of the combination change during the Warranty period, locksmith service fees will NOT be covered.

2. Gain entry with the basic electronic lock

The handle should be all of the way UP, in the horizontal position before attempting to open safe.

Opening your safe for the first time (keep door open during setup):

1. Insert a paper clip or pen point into the small hole of the battery cover located directly below the keypad. Push in while sliding cover to the right (Fig. B).
2. Disconnect and remove battery holder.
   • Insert 4 new AA batteries (not included) to power this lock.
   • Reconnect the battery holder and put back into proper position. Slide battery cover back in place.
   NOTE: The yellow LED will light when the batteries need to be replaced.
3. Simply insert the key (if equipped) in the lock and turn until the plunger pops out. Remove key.
4. Enter the factory code (printed on the first page of this guide). When the green light appears, you have four seconds to turn the handle down to open. Try this several times before proceeding to the next step.

To unlock safe:
Enter the 5-digit factory code, a pre-programmed user code, or a pre-programmed user pin (programming instructions to follow). When the green LED lights you have 4 seconds to turn the handle and open the safe.

To lock safe:
Close the door and return the handle to the horizontal position. For greatest security, depress the key lock (if equipped) with your finger.

NOTE: If your unit is equipped with a water-resistant gasket additional pressure to the left corner of the door may be required before the handle can be returned to the horizontal position.

Access codes
There are 3 possible ways to unlock and access the safe:

1. Factory code
   (Found on the front cover of this guide.) You can always open the safe by entering the pre-set 5-digit factory code. This code cannot be deleted.
2. User code
   If you prefer to employ your own code, you can program the safe to open using a 5-digit user code of your choice.
3. User pin
   If you wish to give someone else temporary access to the safe, you can program a 5-digit user pin that can later be erased.

Programming the user code
NOTE: One (1) user code is allowed.

To add:

1. Press the Prog key , then enter the 5-digit factory code.
2. Enter the 5-digit user code of your choice.

To delete:

1. Press the Prog key.
2. Enter the 5-digit factory code twice.

Programming user pin
NOTE: One (1) user pin is allowed.

To add:

1. Press the Prog key 2 times.
2. Enter your 5-digit user code.
3. Enter the 5-digit user pin of your choice.

To delete:

1. Press the Prog key 2 times.
2. Enter your 5-digit user code.
3. Enter 0, 0, 0, 0, 0.

NOTE: If your safe does not appear to be working, please check batteries before calling Sentry Customer Care.

Signals
Your electronic-lock safe communicates by means of several audio/visual signals.

Red (Error) LED + three beeps indicates one of the following:

1. You have pressed Program key out of sequence.
2. You have entered an invalid code or user pin.
3. You have let 5 seconds or more elapse between key presses.
4. Lights after three consecutive invalid codes are input (2-minute delay mode).

Green LED only:

1. Comes ON after you enter a valid code and remains lit during the 4-second period in which the safe can be opened.
2. Comes ON in the Programming mode and remains lit until you have finished entering a 5-digit code.

Yellow LED only:

1. Comes ON when the batteries need to be replaced.

3. Gain entry with the fingerprint lock

For safes with a fingerprint lock

IMPORTANT
For some fingerprint locks

NOTE: Some models with a fingerprint lock are shipped with a screw in the back of the door (Fig. H). This temporary screw keeps the handle from turning and locking the safe before you are ready to use it. Once your safe is delivered, remove this screw and throw it away (Fig. I). After removing the lock out screw, it may be required to push the bolt button which, in turn, will throw the bolts to a locked position while the door is open (Fig. J). The handle should be all the way UP, in the horizontal position before attempting to program your safe. Your finger-print lock is now ready to use. You will find your safes factory combination on the sticker on the front of the owner’s manual.

NOTE: If you are experiencing difficulty with the operation of the locking mechanism, DO NOT RETURN THIS PRODUCT TO THE STORE. PLEASE VISIT OUR SITE AT WWW.SENTRYSAFE.COM

It is important that you keep this Owner’s Manual in a secure place other than IN your safe; it is your reference for the safe’s Serial Number and Factory Code.

To activate lock
Four alkaline AA batteries, equaling voltage: 6Vdc, (not included) are required to activate the fingerprint lock.

NOTE: Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED.

To install batteries:
The battery compartment is located directly beneath the keypad. Insert a small coin in the slot on the left side of the compartment cover. Twist the coin to dislodge the cover, then slide it to the right. Insert four new batteries as indicated, and slide the cover back in place.

Low battery notice
When the battery power gets low, the message “Batteries Low Replace Soon” will appear with each activation of the lock until batteries are replaced.

NOTE: No codes are erased when old batteries are removed for replacement.

First time use

Open unit first, then test with door open! When you have successfully completed the personal code process described below, the LCD on the screen will prompt the next steps. The instructions provided here serve as a beginning guide.

NOTE: The key lock must be in the UNLOCKED position in order to operate the fingerprint lock. To unlock, turn the key to the right. Return key to the locked position when you have closed the safe door. Remove the key from the lock and store it in a secure location other than in the safe.

To enter your personal code

1. Press ENTER .
2. Enter the 5-digit factory code provided on the front of this manual.
3. Press ENTER .
   NOTE: When you have successfully entered the factory code, the LCD screen will prompt the next steps.
   If you require additional assistance, contact Sentry Customer Service on line at
   www.sentrysafe.com, or call: 1-800-828-1438, 8:00am – 6:00pm E.S.T., M–F.
4. Enter your new personal code consisting of 4–8 digits, then press ENTER.
5. Re-enter your new personal code and press ENTER again. Proceed to fingerprint scan procedure.

To enter fingerprint scans
Tips for fingerprint programming and usage

Best finger for programming

• Do not choose a finger with a cut or scar.
• Do not choose a finger with excessively long fingernails.
• Choose a finger with the tightest swirl pattern.

Finger placement

• Place your finger on the sensor in a direct manner. Do not slide or roll your finger onto the sensor.
• Do not move your finger off of the sensor until the lights around the sensor turn off.
• Any trembling or shaky movement of the finger will result in an inaccurate reading.
• Use a medium pressure on the sensor. Too firm or too light will not read correctly.

Location of finger on the sensor

• Look to see where the swirl part of your fingerprint is on your finger.
• Place the swirl part of your fingerprint on the sensor.
• With your finger on the sensor, note the position of your fingernail in relation to the sensor crosshairs. Repeatable placement of the finger is important in programming and usage of the safe.
• Also note where you are standing in relation to the safe. Programming or usage at a different angle will not work well.

Skin condition

• If you have dirt on your hands, please wash them before using the safe.
• Very dry skin will not program well. Use a skin moisturizer, being sure to rub the moisturizer in well and remove any excess before using the safe.

NOTE: Should you choose not to enter your fingerprint scan at the first use, it can be entered at a later date. The original Factory Code is necessary to continue at that later date.

NOTE: The fingerprint lock stores one manager and up to six (6) users. The manager and each user is encouraged to program two fingers, preferably one finger from each hand.

1. To store your first fingerprint, place one finger on the sensor and follow prompts as they appear on the LCD screen. (Fig. K) Three accurate reads of the fingerprint are necessary for successful enrollment. Remember how you place your finger on the sensor and try to position it in the same place each time.
2. After successful enrollment of the first finger, to store the second fingerprint, press the number 2 and repeat Step 1 using a different finger, preferably one from the other hand. You may enroll additional users at this time or at a later date.

Normal use
To access the safe, first turn the key to the right to unlock. You may then either press the ENTER button and place your finger on the sensor (Fig. K), or, enter your personal code and press ENTER. LCD will prompt the next steps.

For optimal accuracy and fingerprint-reading success, clean the fingerprint sensor periodically with a lint-free cloth.

Enrolling and deleting users
To enroll a new user or delete an existing user, enter your personal code or manager fingerprint scan and press ENTER. Enter a user number (1-6) and follow the prompts which appear on the screen.

Backup
The system memory can be returned to its original status using this sequence and following the screen prompts: 99 > CLEAR > 2004 > ENTER

CAUTION: This action PERMANENTLY ERASES all memory, personal codes and fingerprint scans.

CAUTION: ENVIRONMENTAL CONDITIONS
The electronics may not work or may have a slow reaction time in cold temperatures (50°F or less). Make sure the safe is at room temperature before programming and usage.

Troubleshooting

• If electronics are not functioning, replace batteries first (behind battery cover) as described on page one of this guide.
• If electronics are functioning and you cannot get into safe:
  – Pull handle up
  – Follow instructions for opening your lock.
• You must use both the key (if equipped) and the electronic code to open the safe if the key lock cylinder is pushed in.

Delay mode
Enters a two-minute delay mode after an invalid code has been entered three consecutive times. In this mode, the lock cannot be activated and any key entry will generate an ERROR signal.

Floor mount (optional)
For additional security your safe may be bolted to the floor. For instructions, please visit our website at www.sentrysafe.com.

WARNING
DO NOT store delicate items directly in your safe. SentrySafe products which offer fire protection have a proprietary insulation that has a high moisture content. In addition the SentrySafe.

If you lose your combination/keys or need accessories, we can help!
Visit our website at www.sentrysafe.com

Registration: To be eligible for warranty coverage, the original purchaser must register the product online at www.sentrysafe.com or complete and return to Sentry Group the enclosed registration card.

Advanced safes close airtight to offer water resistance, which may also cause moisture to accumulate inside your safe. The desiccant packet included in your safe during shipment, should be left in your safe. DO NOT DISCARD IT. It is intended to help absorb moisture which may accumulate inside your safe. Please open your unit periodically to avoid moisture accumulation.

If you choose to store delicate items such as jewelry with working parts, watches, stamps, or photos in your safe, we recommend putting them in an air-tight container, prior to placing them in the safe for storage.

NOTE: Sentry Group will not be responsible for any damage or loss of items placed in the unit due to moisture.

WARNING
DO NOT store pearls in this safe unit. In the event of a fire, potential damage to delicate pearls occurs at temperatures much lower than the 350°F interior performance measure which the UL classification performance standard indicated guarantees. Therefore, DO NOT store pearls in your SentrySafe product.

WARNING
No computer disks, audio-visual media or photo negatives. This product is not intended to protect computer floppy or diskettes, cartridges and tapes, audio or video cassettes or photo negatives. For fire-resistant storage of these materials, ask your retailer for the SentrySafe Fire-Safe Media storage products.

Rigorous testing ensures this product meets our specifications

ETL Verified Water-Resistance Protection (if equipped) Tested up to 8 inches of water for up to 24 hours. Note: Maximum allowable leakage is 170 grams. For the gasket to work effectively, the safe door must be closed with the handle fully horizontal. When you move the handle, the compression of the gasket will require slightly more force than you would use with a safe that does not have a gasket.

Manual del Propietario para Caja Fuerte Compacta – Modelo: P005C

•••IMPORTANT••• DO NOT RETURN SAFE TO THE STORE!

If you experience any problems or challenges with your safe, please contact us. Many issues can be resolved quickly without the
product being returned. Customer Care: 1-800-828-1438

SentrySafe Customer Care

Thank you for purchasing a SentrySafe product. If you experience any problems or challenges with your safe, please contact us. Many issues can be resolved quickly without the product being returned. Call our Customer Care department for assistance. Customer Care: 1-800-828-1438
Registration: To be eligible for warranty coverage, the original purchaser must register the product online at www.sentrysafe.com.

This product is not intended for the secure storage of all materials. Items such as firearms, other weapons, combustible materials, or medication should not be stored in this unit.

Getting started

Thank you for purchasing a SentrySafe Product. SentrySafe is the world leader in fire/water resistant and security storage. This guide describes how to easily set-up the product.
Contents Include:
– Compact safe (1)
– Tethering cable (1)
– Owner’s manual
– Warranty card

You can set your own personal combination by following these instructions: The opening combination is preset at 0-0-0.

1. Turn the dial to the preset combination 0-0-0. Remove the lower tray from the safe to expose the lock reset button on the back of the lock mechanism.
2. Move the reset button to position A.
3. Turn the dials to set your desired combination. Write down your combination immediately so you don’t forget.
   
                               Figure 1
4. Move the reset button back to position B

The lock will now open to your own combination. To change your combination repeat steps 1-5 above

NOTE: There is no override code for this safe. It is important to record your new combination in a safe place to avoid being locked out.

1. Open safe.
2. Put the end of the cable (non-loop end) in the slot on the back left corner of the safe.
3. Close lid and lock safe.
   
                                  Figure 2

Registration:
To be eligible for warranty coverage, the original purchaser must register the product online at www.sentrysafe.com.