B60, B60CS, B60F, B62

IMPORTANT: For UL Functions Only (B60F, B60CS)

Before Installing the Lock, Check Door Jamb and Door Preparation

If dimensions are different see http://consumer.schlage.com/service-support

1 Choose Faceplate

2 If Necessary, Adjust Deadbolt

3 Install Deadbolt

SCHLAGE BE489 Smart WiFi Deadbolt

How to add or delete user codes for Schlage Encode™ Smart WiFi
Deadbolt with the touchscreen (BE489)
Warning: Manual programming is disabled after your lock is programmed using the Schlage Home app. If you manually program your lock and choose to later link your lock to the app, all manually programmed user codes and the programming code are deleted.

If you need to find your programming code, look inside the back of your lock. Simply remove the battery cover and you’ll see a label with your Prog. Code.

1. Enter your Programming Code (6 digits)
2. Enter the code you’d like to add or delete.
3. Choose and press either the house button to add, or the lock button to delete:
4. Enter that code again.
5. Press (home) to exit.

www.schlage.co.nz/encode

PROGRAMMING GUIDE

Schlage Button Signals
The color of the Schlage button indicates the status of the lock.

Orange

• the lock is in programming mode

Green

• a correct user code was entered
• the programming process is complete

Red

• an incorrect user code was entered
• there was an error in programming
• low batteries
• red blinking indicates critically low battery

Codes
Control of the lock is simply managed via a six-digit Programming Code and four-digit User Codes.

PROGRAMMING CODE
(Six Numbers)

• The lock comes preset with one unique default Programming Code. It can be found on the stickers, one on the back of the keypad assembly
  and one on the front of this User Guide.
• Used to put the lock in programming mode.
• DOES NOT unlock the lock.
• The first four numbers must be different from all of the User Codes currently in the lock.
• If you forget the Programming Code, you can reset the lock to factory settings, which restores the default Programming Code. See Restore Factory
  Settings on page 15.

USER CODES
(Four Numbers)

• The lock comes preset with two unique default User Codes. They may be found on the stickers, one on the back of the keypad assembly and one
  on the front of this User Guide.
• Used to unlock the lock.
• These four numbers must be different from the first four numbers of the Programming Code.
• Up to 19 possible User Codes can be stored in the lock at one time.

Default Code Locations

The Default User Codes and Programming Code are located in two places:

Back of the Keypad
» You must remove the Keypad from the door to see this sticker.

Front of this User Guide

Basic Controls

» Write your programming code here for easy access. Also see Record Your Codes on page 13 for space to record User Codes.
» If you make a mistake during programming, press the Schlage button repeatedly until the keypad lights blue. Then start over.

ADDING USER CODES*

* These four numbers must be different from the first four numbers of the Programming Code.

DELETING USER CODES

CHANGING THE PROGRAMMING CODE*

* The first four numbers must be different from all of the User Codes currently in the lock.

Want to see a video?
Browse to answers.schlage.com and search on “How to Program Keypad Lock” for a video. Other videos and information are also available.

Enhanced Controls

Schlage’s keypad locks were designed with added features that allow you to adapt the lock to your needs.
Additional features that you can choose to use include:

ENABLE VACATION MODE

When enabled, no User Codes will unlock the door, preventing any unauthorized attempts of entry when no one is home for a prolonged period of time.

DISABLE VACATION MODE
ENABLE OR DISABLE BEEPER

DELETE ALL USER CODES

ENABLE OR DISABLE LOCK & LEAVE KEYPAD DEADBOLT (BE365) ONLY

Enabled by default. When enabled, the deadbolt can be locked from the outside by pressing the Schlage button and rotating the thumbturn. When disabled, a User Code must be entered before rotating the thumbturn. Disabling this feature keeps an unauthorized person from locking the door from the outside.

RECORD YOUR CODES

» KEYPAD WEAR
Consider changing your codes on a periodic basis so buttons wear evenly.

User Codes
»Up to 19 User Codes can be stored in the lock at one time.

TROUBLESHOOTING

Browse to answers.schlage.com and click on Electronic Keypad Locks in the menu on the right side for videos, troubleshooting, FAQ and more.

Lock Issue		Beeps*	Lights	Solution
KEYPAD DEADBOLT ONLY	I can unlock my deadbolt by simply pushing the Schlage button. I don’t need a code.	1 High	Green Blinking	Your lock has been installed incorrectly and is not secure. Repeat the installation process. Ensure the cam and bolt positions are correct, as referenced in the installation instructions. Browse to answers.schlage.com and search on “Installing BE365” for a video.
	After pushing and rotating thumb turn, the deadbolt does not extend.	None	None	Lock and Leave feature is disabled. See Enable or Disable Lock & Leave on page 12.
	After entering my User Code, the lock flashes green, but I cannot unlock the lock.	1 High	Green Blinking	Lock Override is enabled and should be disabled. See Lock Override on page 7.
	Outside thumb turn does not freely spin after the deadbolt is thrown.	None	None	Lock is malfunctioning. Disable the keypad by enabling Lock Override. See Lock Override on page 7. Call Customer Service.
I forgot my Programming Code.		None	None	Check the front of this guide or the back of the keypad assembly for the default Programming Code.
				If needed, restore lock to factory settings. See Restore Factory Settings on page 15.
I need to delete a User Code that I don’t remember.		None	None	Delete all User Codes. Then add all needed User Codes back into the lock. See Programming Guide on page 10.
User Code does not unlock lock.		2	Red	User Code entered is not a valid User Code.
		1 High, 1 Low	Green then Red	Vacation Mode is enabled. See Disable Vacation Mode on page 12.
does not light when numbers are pressed.		None	None	Too many incorrect User Codes have been entered. Wait 30 seconds and try again.
				If keypad does not respond after 30 seconds, then replace battery. See Changing the Battery on page 6 for Keypad Deadbolt or Changing the Battery on page 9 for Keypad Lock.
There is a delay before unlock after a valid User Code is entered.		High/ Low, then 1	Red then Green	Battery is low and should be replaced. See Changing the Battery on page 6 for Keypad Deadbolt or Changing the Battery on page 9 for Keypad Lock.
blinking red but no codes have been entered.		None	Quick Red Blinking	Battery is dead and MUST be replaced. See Changing the Battery on page 6 for Keypad Deadbolt or Changing the Battery on page 9 for Keypad Lock.

Cannot add a new User Code.	High/Low	Red	19 User Codes already exist. Delete a User Code before adding a new one. See Deleting User Codes on page 11.
	2	Red	Second User Code entered did not match first User Code entered. See Adding User Codes* on page 11.
			The User Code matches the first four digits of the existing Programming Code.
Cannot delete a User Code.	2	Red	Second User Code entered did not match first User Code entered.
Cannot change Programming Code.	2	Red	Second Programming Code entered did not match first Programming Code entered. See Changing the Programming Code* on page 11.
			First four digits of new Programming Code match an existing User Code.
Cannot delete all User Codes.	2	Red	Programming Code entered second time is incorrect.
Lock will not stay in programming mode.	2	Red	Any key other than was pressed immediately after programming mode was entered.
			An incorrect entry was made during the programming process.

* Number of beeps if beeper is turned on.

Restore Factory Settings

If you lose or forget your Programming Code, you can restore the factory settings, which will restore the default Programming code.

1. Disconnect the battery.
2. Press and release the Schlage button.
3. The following steps must occur within 10 seconds:
   a. Reconnect the battery. The Schlage button will light green for one second.
   b. Then, press and hold the Schlage button until it lights green and the lock beeps.
4. Try entering one of the default User Codes. If it does not unlock the lock, start over at step 2.

Once you’ve done this, you can change the programming code to a personalized number. See Changing the Programming Code* on page 11.

WARNING
Locate the default Programming and User Codes on the front of this guide or the back of the Keypad Assembly before beginning! Default Programming and User Codes will be restored. All existing User Codes and current Programming Code will be erased. CUSTOMER SERVICE CANNOT RETRIEVE LOST DEFAULT CODES! DO NOT RESTORE FACTORY SETTINGS UNLESS YOU CAN LOCATE THE DEFAULT CODES.

Prepare door

If insulator strip is present, carefully remove it.

Install sex bolts to secure device.

Install grommet.

Install device per manufacturer instructions.

Install spindle into assembly.

Check lever handing.

Install cylinder and lever.

Install outside assembly

Install inside assembly.

Install cover and screw.

Install batteries.

Set up lock.

After installing the lock, see the user guide for setup and operation.

Lever Removal

Changing the cylinder’s tailpiece

• Remove USB plug.
• Remove cover from baseplate.
• Remove spring cage.
• Move lever stop to opposite side − Align arrow with latch.
• Reinstall springcage.
• Reassemble cover and baseplate.

IMPORTANT: Do not pinch the ribbon cable duringreassembly. Vuelva a ensamblar la cubierta y la placa base.

Schlage Control™ Smart Deadbolts

BE467F, Grade 2

Schlage Control™ Smart Deadbolt with Addison trim in Aged Bronze

Schlage Control™ Smart Deadbolt with Greenwich trim in Satin Nickel

Schlage Control™ Smart Deadbolts mark a new era of electronic access control in the multi-family world. By ushering in the next generation of highly scalable, efficiency boosting capabilities, multi-family properties can focus on operating more profitably—and with greater appeal for residents.

Using cloud-based mobile or web apps, facility staff can configure and manage access from virtually anywhere. The open integration capabilities, in conjunction with ENGAGE™ Technology, offers flexible, streamlined control and the freedom to integrate with alliance software partners to manage a wide spectrum of facility needs. Residents will enjoy the convenience of using a smartphone and/or smart credentials to open doors.

Schlage Control™ Smart Deadbolts are part of an extensive Allegion® lineup, which holds a solution for every door a multi-family property needs to manage.

Benefits

• Improves security & safety, reduces liability
  • No-cylinder design makes locks 100% pick and bump proof
  • Designed for accessibility using smart credentials and/or smartphone
• Increases efficiency of property operations
  • Eliminates cost and hassle of managing of keys
  • No-tour functionality (altering access to a lock without having to visit it)
• Maximize return on investment
  • Smart credentials eliminate lock rekeying costs
  • Upgrades property visual appeal

Features

• Keyless, no cylinder design — 100% bump and pick-proof
• Modern credentials — smart credential and/or smartphone as key
• Lock programming via mobile application on phone and/or tablet (Bluetooth® connection)
• Supports both on-line (Gateway Required) and off-line applications
• Up to 500 users per lock
• Audit trail reports up to 1,000 events
• Fits standard door prep
• 2-year battery life (Off-Line Mode)
• Full suiting with Schlage decorative mechanical locks
• ADA compliant design

Markets

• Multi-family communities
• Senior living communities
• Student housing
• Military housing

Specifications

• Latch: 1” x 2-1/4” square and round corner faceplate (round corner standard, square corner included in package) 1” edge bore required
• Strikes: 1-1/8” x 2-3/4”, round corner, no box, latch strike
• Backset: Adjustable backset, fits 2-3/8” to 2-3/4” backsets
• Door Range: 1-3/8” to 1-3/4” (thick door kit available – up 2-1/4”)
• Hole Distance: Minimum 4” center-to-center distance between cross bore holes
• Battery: 4-AA batteries included, (If loss of battery power occurs, a 9V battery can be used to jump start the lock and provide access with an assigned credential.)
• Construction: All-metal chassis and escutcheons
• Bore: 2-1/8”
• Credential: Supports smart and multi-technology aptiQ MIFARE classic or aptiQ DESFire EV1
• Stile width: Minimum 4-1/2” stile for 2-3/8” backset, minimum 5” stile for 2-3/4”
• Certifications: 90 minute UL Listed A 156.12 Grade 2 ANSI/BHMA certified
• Operating Temperature Exterior Side: -35C to 66C
• Operating Temperature Interior Side: -10C to 50C

Style Options

BE467F Schlage Control™ Smart Deadbolt with Addison trim in Aged Bronze

BE467F Schlage Control™ Smart Deadbolt with Greenwich trim in Satin Nickel

Finish Options

Matching Lever Designs (Ordered separately)

BE467F Schlage Control™ Smart Deadbolt Lock with Addison trim in Aged Bronze with Accent lever

BE467F Schlage Control™ Smart Deadbolt Lock with Greenwich trim in Satin Nickel with Broadway Lever

Model FC60, Handleset

a. Cylinder

b. Cylinder ring

c. Keys (2)

d. Bolt

e. Bolt strike

f. Reinforcement strike

g. Reinforcement screws

h. Thumbturn

i. Thumbturn screws

j. Handle

k. Latch

l. Latch strike

m. Latch/Bolt/Strike screws (8)

n. Chassis

o. Chassis screws

p. Trim

q. Knob/Lever

r. Washer

s. Handle bolt

t. Bolt cover

u. Drive-in faceplate

v. Hex wrench (Do not discard!)

1. Check door dimensions.

1a If dimensions do not match, you may need to modify your door.

* May vary from 8 1/4″ (210 mm) to 9 3/4″ (248 mm) for existing hole.

1b Check latch and bolt length.

Measure the backset as shown.

• 2 3/8″ (60 mm): no adjustment is necessary.
• 2 3/4″ (70 mm): see the Adjust latch and bolt section.

2. Install the latch and bolt.

2a Choose the faceplate.

2b Secure with screws.

or 2b Use wood block and hammer.

3. Install the strikes onto the door frame.

Use included strikes for best performance.

4. Install the handle into the bottom hole.

You may need help holding the handle in place during installation.

Push firmly! Then hold in place.

5. Install the interior chassis.

5a Chassis is spring-loaded. Push against door and hold in place.

5b Secure with two (2) screws. Make sure chassis is straight!

6. Install the handle bolt.

7. Install the interior trim.

8. Install the interior knob/lever.

8a Push knob/lever firmly into place.

8b Then tighten set screw.

9. Install the cylinder and ring into the top hole.

10. Install the thumbturn.

10a Align slot in thumbturn with tailpiece.

10b Secure with screws.

Change levers

1. Loosen set screw, but do not remove.

2. Pull lever off.

3. Reinstall appropriately. Then tighten set screw.

Adjust latch and bolt

For 2 3/4″ backset, rotate and pull latch/bolt out to long setting.

Change faceplate

F-Series, F-Series UL

Installation Instructions

1. Check door preparation.

TEMPLATE

2. Choose faceplate to match door.

3. For UL functions only (CF, CS)

4. Install latch.

5. Install outside lever or knob

6. Install strike.

7. If necessary, switch levers.

Non-Keyed Functions

OR

Installation Instructions

Tools

A. Key
B. Cylinder Cap
C. iButton Assembly
D. Deadbolt
E. Mounting Plate
F. 9v Battery
G. Mounting Screws (2)
H. Thumbturn Assembly
J. Screws (2)
K. Drive-in Faceplate
L. Square-corner Faceplate
M. Rounded-corner Faceplate
N. Deadbolt/Strike Screws (4)
P. Strike
Q. Reinforcement Screws (3)
R. Dust Box
S. UL Cup (BE367F ONLY)
T. UL Screw (BE367F ONLY)

Install Lock

1  Template Is Included In Box

IMPORTANT: Template shown is not full size

2 Check Door Holes

Note: If holes do not match template, purchase a GuideRight® jig or visit www.schlage.com for door drilling instructions.

3 FOR BE367F ONLY: Measure and Drill Hole

4 FOR BE367F ONLY: Install UL Cup

5 If Needed, Adjust Deadbolt

6 Choose Deadbolt Faceplate

Match faceplate to your door.

7 Install Deadbolt

8 Install Keypad Assembly

IMPORTANT: Cable passes over top of deadbolt.

9 Install Inside Mounting Plate

IMPORTANT: Pull excess wire through mounting plate.

10 Check Cam and Install Screws

NOTE: Ensure lock is straight before tightening.

11 Install Battery and Connect Cables

12 Route and Tuck Cables

13 Install Thumbturn

14 Install Strike and Dust Box

Check Operation

If you have a yellow construction iButton Credential, then test lock operation

IMPORTANT: If the BE367 is unprogrammed, then all yellow construction iButtons will operate lock. Yellow Construction iButtons are disabled automatically when the BE367 is programmed.

For Programming, See the SMS/SMS Express Site Set-Up Guide

Questions? (888) 805-9837

© Allegion 2014
Printed in U.S.A.
P515-488 Rev. 11/14-online

Installation Manual

Home Keypad Lock BE369

1.Important Information

• Lock comes preset with a default Programming Code.
• Lock comes preset with two default User Codes

Need Help?

  (888) 805-9837 (U.S.A./Canada)

Tools Needed

• Phillips screwdriver
• Tape Measure
• Pencil

Optional

• Flathead Screwdriver
• Wood Block
• Hammer

  Do not use a power drill for installation

2. Install deadbolt and strike.

2a. Check dimensions.

If door dimensions do not match, go to www.nexiahome.com for drilling instructions.

2b. Check backset.
This lock will fit either a 2^3/8 ” backset or a 2^3/4 ” backset. The bolt is preset to fit a 2^3/8” backset. If your backset is not 2^3/8”, you need to adjust your bolt by rotating it counterclockwise.

2c. If necessary, change bolt faceplate

Check edge of door to determine the type of faceplate required.

2d. Install bolt.

The word “TOP” should be facing upward.

3. Align tailpiece of exterior keypad and interior baseplate.

3a. Check the cam on the interior baseplate.

Locate the cam on the baseplate. This cam has a small arrow on it that should point to the arrow that is printed on the casing above the cam, like picture “a” below. If the cam is oriented sideways, like the picture “b”, rotate the cam until the arrows match.

3b. Install exterior keypad.
Bar should slide smoothly through hole in latch. If not, check door dimensions. Feed the cable over the top of the bolt assembly then slide the tailpiece through the correct hole as shown below.

3c. Install the interior baseplate.
Feed the cable through the hole as shown below. DO NOT connect the cable at this time. Then slide the baseplate onto the tailpiece and press against the door. The baseplate should stay in place.

4. Secure interior baseplate and install batteries.

4a. Secure interior baseplate.

Use the two screws shown to secure the baseplate to the door.

4b. Connect cable.

Snap the connectors together. Tuck them into the open space in the baseplate. Make sure no wires will be pinched when the cover is installed.

4c. Install batteries.

1. Unscrew battery holder.
2. Slide out battery holder and install batteries.
3. Attach 9 volt battery to battery connector.
4. Place 9 volt battery in compartment.

5. Install interior cover.

5a. Install cover.

Place the cover against the door and secure using the two screws. You may need to rotate the thumbturn to the proper position, shown below.

Tuck wires into open space on baseplate. Be careful not to pinch any wires between cover and baseplate.

6. Install the strike.

6a. Prepare the frame for the strike.

Mark the 4 hole locations. Drill them as shown.
If the strike cut-out has not been prepared in the frame, see the specifications on the right

6b. Install the strike.

7. Test lock.

  TEST WITH DOOR OPEN!

7a. Test locking function.

1. Press
2. Rotate thumbturn towards door edge until bolt extends.

7b. Test unlocking function.

1. 1.  Find User Code A on the yellow sticker.
   2. Enter User Code A (four digits) into the keypad.
   3. Rotate thumbturn away from door edge until bolt retracts.

FCC STATEMENT

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this equipment not expressly approved by Schlage could void the user’s authority to operate the equipment.

FCC ID: P2GBE369    IC: 7654A-BE369

© Allegion 2014
Printed in U.S.A.
P516-085 09/14-d

Instructions Instructions

Schlage Keyless Touchscreen Deadbolt [BE375]

Keyless Touchscreen Deadbolt

Prepare for Installation

Tools Needed

• Phillips screwdriver
• Tape Measure
• Pencil

Optional

• Flathead Screwdriver
• Wood Block
• Hammer

IMPORTANT NOTES

DO NOT use a power drill for installation!

• Install and test lock with door open to avoid being locked out.
• If tailpiece is not installed, insert into slot on the back of the touchscreen and snap into place.

A Check door dimensions.

See consumer.schlage.com/Service-Support for door preparation instructions if dimensions are different.

B Adjust bolt length, if necessary.

Measure the dimension shown. If the measurement is 2Cv” (70 mm), extend the bolt.

C Change faceplate, if necessary.

Choose the drawing that matches your door edge.

Install Lock

1. Install the bolt.

2. Install the touchscreen on the outside of the door.

Slide tailpiece through the slot in the bolt, and route wire over bolt.

3. Install the thumbturn assembly.

3a Rotate the thumbturn to a vertical position.

3b Remove the battery cover.

3c Route battery cable from the touchscreen through the hole in the thumbturn assembly.

3d Place thumbturn assembly against the door and secure with two (2) screws.

3e Connect the wires.

4 Install the included battery.

IMPORTANT
Route the battery wire so it won’t be pinched by the cover!

4a Install the battery cover. Do not pinch the wires!

5 Install reinforcement plate and strike into door jamb.

Test Lock

A. Extend the bolt (lock).

Did bolt extend?

B. Retract the bolt (unlock).

IMPORTANT
Press Schlage and rotate thumbturn away from the door edge. If the bolt retracts, the lock is not installed correctly. Pay attention to step 3a and try again.

Did bolt retract?

Program Lock

See the Schlage Touch™ User Guide that came with this lock. Go to schlage.com for videos and more. Register your product at RegisterMySchlage.com.

Lifetime Limited Mechanical and Finish Warranty and 3-Year Limited Electronics
Warranty
Subject to the terms and conditions of this warranty, Schlage extends a lifetime limited
mechanical and finish warranty and a three-year limited electronics warranty to the original
consumer user (“Original User”) of our Schlage brand product (“Product”) against defects in
material and workmanship, as long as the Original User occupies the residential premises upon
which the Product was originally installed.

What Schlage will do: Upon return of the defective Product to Schlage, Schlage’s sole
obligation, at its option, is to either repair or replace the Product, or refund the original purchase
price in exchange for the Product.

Original User: This warranty only applies to the Original User of Products. This warranty is not
transferable.

What is not covered: The following costs, expenses and damages are not covered by the provisions of this limited Warranty: (i) labor costs including, but not limited to, such costs as the removal and reinstallation of Product; (ii) shipping and freight expenses required to return Product to Schlage; and (iii) any other incidental, consequential, indirect, special and/ or punitive damages, whether based on contract, warranty, tort (including, but not limited to, strict liability or negligence), patent infringement, or otherwise, even if advised of the possibility of such damages. Some local laws do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion or limitation may not apply to you.

The provisions of this warranty do not apply to Products: (i) used in commercial applications; (ii) used in common area applications; (iii) used for purposes for which they
are not designed or intended; (iv) which have been subjected to alteration, abuse, misuse,
negligence or accident; (v) which have been improperly stored, installed, maintained or
operated; (vi) which have been used in violation of written instructions provided by Schlage;
(vii) which have been subjected to improper temperature, humidity or other environmental
conditions; or (viii) which, based on Schlage’s examination, do not disclose to Schlage’s
satisfaction non- an implied warranty lasts, so that the above limitations may not fully apply.
Refer to your local laws for your specific rights under this warranty.

Guaranteed Fit Program: Schlage products are designed to fit standard residential door preparations and retrofit existing tubular locks. Note: Mortise locks and preparations are not
considered standard and are not guaranteed under this program.

During the initial installation, if there is a problem with the Product’s performance, the Original
User may simply contact Schlage Customer Service at 888-805-9837 in the U.S. and Canada or 800-506-7866 in Mexico for assistance.Program and warranty claims: If you encounter a residential door preparation or fit issue under the Guaranteed Fit Program or have a claim under
this warranty, please contact Schlage Customer Service for repair, replacement or refund of the
original purchase price in exchange for the return of the Product to Schlage.

Schlage Customer Service
Calling From:
U.S.A.: (888) 805-9837
Canada: (800) 997-4734
Mexico: 018005067866

© Allegion 2014
Printed in U.S.A.
P516-865 Rev. 06/14-b