resideo IPCAM-WOC2 HD Wi-Fi Outdoor Video Camera

IPCAM-WOC2 is a 1080p, full HD Wi-Fi® video camera intended for outdoor use with Resideo Total Connect® 2.0.

• Camera setup requires a Total Connect® 2.0 account and the Total Connect 2.0 mobile app. Video Services must be enabled in AlarmNet 360™.
• Camera operation requires minimum available bandwidth of 2.1 Mbps.

Package Contents

1. A. Camera
2. B. Sun Shield
3. C. Power Cable Extension [8′ Cable]
4. D. Power Adapter with 7′ Cable
5. E. Pig-tail Power Cable
6. F. Screws and Allen Wrench
7. G. Antenna
8. a. Bluetooth Antenna
9. b. Not Used
10. c. Reset Switch
11. d. Power

Planning Configuration and Installation

See the other side of this sheet for more about mounting at the installation site

• The camera should be situated within 200 feet (61 m) of a power outlet and within the verified range of its Wi-Fi® connection. DO NOT mount the camera within 1 foot (0.3 m) of any other wireless device. Depending on the specifics of your installation, a range extender may be needed to ensure adequate Wi-Fi signal strength.
• Pre-installation: It is strongly recommended that camera configuration be done as close as possible to the Wi-Fi router with which the camera will be linked. After setup, use a third-party app to check signal strength at the installation site before mounting (over for more information on signal strength.)
• The power adapter must be connected to a non-switchable power outlet.
• Direct sunlight on the camera lens/image sensor may affect picture quality. When placing the camera, consider how the lighting can vary with time of day and other conditions. The included sun shield can be attached to the camera to help minimize problems with sun glare.

IMPORTANT: Use only ONE of the included power extension cables. This cable adds 8feet (2.44 m) to the supplied power adapter for a total of 15 feet (4.5 m). Alternately, you may use the pig-tail power cable to extend the power adapter cable with a maximum of 200 feet (61 m) of 18 AWG wire.
If the included extension cable is not used, you may cut and splice (observing good workmanship) the power transformer cable.

Ensure proper polarity if the pig-tail power cable is used. The pig-tail’s black (negative) wire must be connected to the negative (white dashed) wire on the power adapter.

Wi-Fi Configuration and Camera Registration

STEP 1
Download the Total Connect® 2.0 app from the App Store or on Google Play. (Look for the red Total Connect 2.0 logo.) Note: Significant differences between the
iOS and Android versions of the app are noted in these instructions.

For best results, configure only one camera at a time.
Check these settings when you turn on your mobile device’s Wi-Fi and Bluetooth:

• Make sure the Bluetooth isn’t connected to another device. such as headphones
• Also, make sure the mobile device is NOT on Silent (ringer and speaker should be audible)

STEP 2 

1. Verify that the camera’s antenna is securely connected.
2. Turn on your smart device’s Bluetooth and Wi-Fi.
3. Launch the app and sign in with your Total Connect® 2.0 account.
4. Plug the power supply into an AC outlet, but:
   DON’T CONNECT THE POWER SUPPLY TO THE CAMERA YET! When you do, refer to the diagram at right ➔

STEP 3
If your account has more than one Location, select the appropriate one using the dropdown v menu at the top of the screen.
Press CAMERAS at the bottom (iOS) or top (Android) of the screen. (Remember that the horizontal Navigation Order can be customized in iOS.)

1. At upper right, press ADD CAMERA (iOS) or (±) (Android)
2. Select the type of camera you’re installing. The names of the camera models may vary from the illustration at right.
3. Name the camera and press NEXT.
4. Connect the power supply to the camera. The LED at the top flashes various colors. Then, WAIT for the camera’s LED to flash blue only. This may take a couple of minutes.
5. Press NEXT on the app.

STEP 4 

1. On the Pair Your Camera screen, press Generate QR Code. After a brief wait, the code appears.
2. Show the QR code on your device to the camera from 3 – 8 inches away.
   If you can, keep an eye on your device’s screen; when the code is scanned successfully. a confirmation message will appear over the QR code.
   The app will also provide audible confirmation via your mobile device’s speaker.
3. Select your Wi-Fi network and press NEXT.
4. Enter the network password and press NEXT. Final setup begins.

STEP 5
When setup is complete, the LED on the camera changes from steady blue, to purple and finally to steady green.
The app also displays Setup Successful*. Press DONE or ADD ANOTHER CAMERA.
After setup, go back to the CAMERAS page and check your newly-registered camera.
Touch the preview image to launch a live stream from the camera.
*The app will tell you if you need to repeat the setup process. This involves resetting the camera, which is described in the app itself
See the other side of this sheet for more information about the required steps.

RESETTING CAMERA

FCC STATMENT

This radio transmitter [IC: 573F-IPCAMWOC2] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

resideo R200 Monitor Installation Guide

R200C2-A

Introduction

Thank you for the purchase of this carbon dioxide monitor. Carbon dioxide is also known as CO2. This product is designed for measuring CO2 concentrations as well as air temperature and humidity. To be used at home, office, school, canteen, etc. The CO2 monitor adapts itself to its  environment (auto calibration). No settings need to be made. This CO2 monitor alerts users through voice messages and audible alarms. Always avoid exposure to high concentrations of CO2. This product, when used properly, is designed to alert you to elevated levels to CO2 so that you may take action to remove yourself from such environment.

• Accurate measurement of:
  • carbon dioxide, ± 50ppm ± 5%
  • temperature, ± 0.5°C or 0.9°F
  • moisture, ± 5% RH
• LED status indication
• Voice alarm notification
• Automatic adjustment of the display brightness
• Rechargeable internal backup battery (approx. 12 hours)

Explanation

Where to install the device?

The CO2 sensor needs a process that adapts to the current environment. In order to achieve a more accurate detection effect, after changing the CO2 monitor’s location it should continue to work for more than 24 hours to complete the automatic calibration. After the completion, the calibration will not be performed at the next startup. Ideally, a device should be installed in every room containing a fuel-burning appliance and in a room where the occupant(s) spend most of their time, like the living room, bedroom and study or hobby room. The CO2 monitor can be wall mounted (eye level) – use cable input A (see page 2), or placed on a cabinet or table/desk – use cable input B (see page 2).

Where not to install the device

In an enclosed space (for example in a cupboard or behind a curtain).
Where it can be obstructed (for example by furniture).
Directly above a sink.
Next to a door or window.
Next to an extractor fan.
Next to an air vent or other similar ventilation openings.
In an area where the temperature may drop below -5°C or exceed 50°C.
Where dirt and dust may block the sensor.
In a damp or humid location. In the immediate vicinity of a cooking appliance.

Mounting

The CO2 Monitor comes with screws and wall plugs for mounting on the wall. Remove the CO2 Monitor from the mounting plate, turn (11) counterclockwise approximate 15°. Use the mounting plate to mark the drill holes. After drilling, place the dowels in the holes and then screw down the mounting plate with the screws. Switch on the back-up battery (10), fully charged is approximate 12 hours usage without adapter connection. Connect the adapter to the CO2 monitor (9) and a power outlet. Place the CO2 Monitor on the mounting plate and turn (12) approximate 15° clockwise.

Status indicator – Green / Yellow / Red

When CO2 concentration is ≤1000PPM, the status indicator turns green.
When CO2 concentration is 1000PPM ~ 1500 PPM, the status indicator turns yellow.
When CO2 concentration is ≥1500 PPM, the status indicator turns red and a 75db@1m alarm is emitted.
Take actions recommended in Section 8 to prevent risks to your health and safety.

Explanation operation buttons

Short press to switch between temperature, humidity and CO2 display.

Short press to get temperature display and then long press to set degrees Celcius or degrees Fahrenheit.

Short press to get CO2 display and then long press to set alarm sound ON/OFF.

Long press to test the alarm. Short press to delay/hush the alarm for 10 minutes.

Within 150 seconds from turning the product on, press and hold both keys simultaneously for 3 seconds. You will hear a voice message in the currently selected language. Press again for 3 seconds and the selection moves to the next available language.

Recommended actions when the CO2 Monitor warning has been activated

Keep calm.
Open all doors and windows and turn off all combustion appliances. If the CO2 Monitor continues to sound the alarm, evacuate your home. Leave all doors and windows open and do not enter until the alarm has stopped. Seek medical attention for anyone who may be suffering from the effects of carbon dioxide.

Carbon dioxide levels and guidelines

Maintenance

We recommend to manually test CO2 Monitor once a month by pressing and holding the test button. Dust is a major cause of false alarms. Therefore, clean the CO2 Monitor once a month. Use a vacuum cleaner to gently remove any accumulated dust along the sides of the CO2 Monitor. Never use a wet cloth or detergent to clean your CO2 Monitor. Clean the device with a soft, damp and lint-free cloth. Make sure that no moisture enters the housing. Do not use any sprays, solvents, alcohol based cleaning agents or abrasive cleaners, but only clean water to moisten the cloth.

This manual contains important safety information about the CO2 Monitor.
Read the manual carefully and keep it in a safe place for future reference.
Do not open the device in case it is damaged.
Do not remove any safety signs, stickers or labels from the device. Keep all safety signs, stickers and labels legible condition.
This product cannot be used in factories, warehouses and other industrial environments that may be in high CO2 concentration for a long time.
If the product is to be placed in a narrow space, the space should be well ventilated, especially the two diffusion windows should be in a well-ventilated position.
The product should be away from heat source, and avoid direct sunlight or other thermal radiation. This product should not be used in the environment with high dust density for a long time.

Service and Contact

For questions about the installation, use or operation of this product please visit www.resideo.com and use the search engine to find more information. Please While every effort has been made to ensure accuracy in this publication, no responsibility can be accepted for errors or omissions.
Data may change, as well as legislation, and you are strongly advised to obtain copies of the most recently issued regulations, standards, and guidelines.
This publication is not intended to form the basis of a contract.

    When the unit has come to the end of its life, dispose of it in accordance with local regulations. It is classified as electronic waste contains a battery and therefore should be disposed of separately  household waste.

   CE compliance logo. This product is in conformity with the European union harmonization legislation.

www.resido.com
Resideo Technologies, Inc
Ademco 1 Ltd., 200 Berkshire Place,
Winnersh Triangle, Berkshire,
RG41 5RD – UNITED KINGDOM
© 2021 Resideo Technologies, Inc. All rights reserved.
This product is manufactured by Resideo Technologies, Inc. and its affiliates.