PIX-LINK WR22 300Mbps WiFi Wireless Signal Amplification Enhancement Extender

PIX-LINK WR22 300Mbps WiFi Wireless Signal Amplification Enhancement Extender

LED Explanation

LED	Status	Indication
	On	Normal power supply
	Off	Abnormal power supply or no power supply.
	On	WIFI UP.
	Blinking	WIFI is transmitting or receiving data.
	Off	WIFI Down or WIFI abnormal
	On	Cable accessed.
	Blinking	The port is transmitting or receiving data.
	Off	The port abnormal or cable unplugged
	Flashing	WPS UP.
	Off	WPS Down.
Repeater (AP Mode)	off	The system is operating normally.
	Quick Blinking	System set factory default.
Repeater (Repeater Mode)	On	WPS successful or Relay successful.
	Slow Blinking	WPS failure or relay failure
	Quick Blinking	System set factory default

Ports and Buttons

Config Repeater Mode

Repeater Mode: Connect your devices to the Repeater wirelessly or via an Ethernet cable, then enjoy the internet.

Power On

Plug the Repeater into a power outlet next to your router.

Set-Up

Method 1: Via a Web Browser

1. Connect your computer or smartphone to the Repeater’s network: PIX-LINK-2.4G, Default Password is 12345678. If you are using a computer, unplug the Ethernet cable if any. The default wireless name can be viewed on the bottom label of the repeater.
   
2. Launch a web browser, and enter http://192.168.7.234 or set up. pix-link.net address bar. Then enter password: admin to login.
   Note: If the login window does not appear, refer to FAQ-1.
   
3. Follow web instructions to complete the setup.
   a. Click Repeater Mode.
   
   b. The system will automatically scan the surrounding wireless networks.
   c.Select the SSID of the master router and enter Repeater SSID and the Password. The default Repeater SSID is set to be XXXX-EXT(XXXX indicates The master router s wireless network name). Then click Apply to complete setup.
   Note: The Password is the same as your master router.
   
   d. The Repeater LED should turn solid on, indicating a successful connection to your router.
   Note: If the LED does not turn solid on, refer to FAQ-2.

e. Connect your devices to the Repeater wirelessly or via an Ethernet cable, then enjoy the internet.

 Relocate

1. Plugin the Repeater about halfway between your router and the Wi-Fi dead zone. The location you choose must be within the range of your router.
2. Wait for about 2 minutes until the Signal LED turns solid Green. If it doesn’t, relocate the Repeater closer to the router to achieve better signal quality.
   

Method 2: Via the WPS Button

1. Press the WPS button on your router.
   
2. Within 2 minutes, press the WPS button on the Repeater for 1 second. The Repeater LED should change from blinking to solid on, indicating a successful connection. Note: If the Repeater LED does not turn solid on, try again or use Method 1 or 2.

Config AP Mode

AP Mode: Traditional wired router realizes wireless function: This repeater can connect to uplink router’s LAN port by wired connection, convert wired signals to wireless signals, the user terminal can connect to this router by wireless connection. Sma phone Tablet Laptop

1 Power On
Plug the Repeater into a power outlet next to your router.
2 Set Up
Method 1: Via a Web Browser

1. Connect your computer or smartphone to the Repeater’s network: PIX-LINK-2.4G, Default Password is 12345678. If you are using a computer, unplug the Ethernet cable if any. The default wireless name can be viewed on the bottom label of the repeater.
   
2. Launch a web browser, and enter http://192.168.7.234 or set up. pix-link.net address bar. Then enter password: admin to login.
   Note: If the login window does not appear, refer to FAQ-1.
   
3. Follow web instructions to complete the setup.
   a. Click AP Mode.

b.Enter SSID and Password, click a to complete the Settings.
c. Connect the Repeater to the Lan port of your router with an Ethernet cable.

d. Connect your devices to the Repeater wirelessly, then enjoy the internet.
Frequently Asked Questions (FAQ)

1. Unable to access the administration page?  Please make more detailed checks as follows:
   • Computer wired configuration: Ensure your computer gets the address automatically. Ensure your computer is connected to the router’s LAN port with the cable, and the network indicators on both sides are lit.
   • Mobile phone or computer wireless configuration: Please make sure that the connected WIFI is the WIFI of this device, and the password is entered correctly.
   • Please open your browser and make sure that you have entered the correct IP address or domain name.
   • Please relaunch your browser or try another browser (such as Firefox or Chrome).
   • Please replace the network cable, or replace another computer and try again.
   • Please reset the device factory default and repeat the above steps again if the issue still exists.
2. After the “Repeater Mode” configuration of the device is completed, the Repeater light is not always on, and the relay signal cannot be connected to the Internet. The Repeater light of the device is not always on to indicate that the Repeater is not successfully paired, which is usually caused by the following problems:
   • When filling in the wireless router, the password is entered incorrectly. When setting, open the small eye behind the password box to check whether the password is correct.
   • The original signal received by the set device is too weak. Please install the mobile device in an area where the Wi-Fi signal is relatively good. (For example, the wireless router is in the living room and the bedroom signal is poor. Then we set it up. The repeater is placed on the socket outside the bedroom, between the bedroom and the living room. Do not use it in the bedroom) this can ensure the network speed of the relay signal and expand the coverage of the Wi-Fi signal.
   • Reset the device and then configure it
3. Under what circumstances can’t the relay be successful?
   • The original wireless router Wi-Fi name or password has special symbols;
   • A small number of telecommunications optical modems (Chinanet), mobile optical modems (CMCC-), and Unicom optical modems (Unicorn) are relayed due to their own limitations or weak signals, which may cause problems such as unsuccessful relaying.
   • If the repeater or client fails to obtain the address after the optical modern is successfully relayed, please restore the device to factory settings and follow the steps below: Login—Advanced—Management —Enforce DHCP—Enable—Apply, and then relay the optical modem again, the client can connect.
4. The cell phone, tablet, or laptop cannot associate with the WIFI network? Please make more detailed checks as follows:
   • Ensure the WIFI function on the mobile device works normally, for example, the WIFI switch is turned on, and the wireless signal can be scanned. Ensure the router is set up correctly.
   • Please make sure that the wireless name selected and the wireless Pass Phrase entered are correct (case sensitive) when establishing the wireless association. Please reset the device factory default and repeat the above steps again if the issue still exists.
5. How to restore the device to the factory default?
   • Press and hold the “Reset” button on the back of the device for more than 5s until the Repeater led quick blinking.

Note: All configurations will be cleared and you need to reconfigure your device after set factory default.
Warning:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different. from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  NOTE: This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter

RF Exposure Statement

To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm the radiator your body. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter

320*160mm
80*80mm
105G

FAQ’S

What is the difference between Repeater and Access Point?

Repeater extends the wireless network coverage, while Access Point creates a new wireless network.

What is the difference between Repeater and Wireless Bridge?

Wireless Bridge connects two wired networks via wireless connection, while Repeater connects one wired network with one wireless network.

What is the difference between Repeater and Wireless USB Adapter?

Wireless USB Adapter connects a computer to a wireless network, while Repeater extends a wireless network.

How to use WPS to set up the PIX-LINK WR22 300Mbps WiFi Wireless Signal Amplification Enhancement Extender?

Please refer to the user manual for details.

How do I setup a wireless pix-link?

Launch a web browser, and enter http://192.168.7.1 or set up. pix-link. net in the address bar.
The default wireless name can be viewed on the bottom label of the repeater.
Follow web instructions to complete the setup.
Click AP Mode.
Enter SSID and Pass Phrase, and click apply to complete the Settings. AP Mode.

How do I change my Pix router password?

Resetting the admin password of most PIX-LINK routers is simple and requires pushing a reset button, located on the router itself, for 5 to 10 seconds

Does Wi-Fi router need SIM card?

A 4G WiFi router, containing a built-in LTE broadband modem, uses a SIM card to share internet connections. You can use a 4G WiFi router for internet sharing anywhere, as long as it is within the network range of the network service provided by your mobile operator

How do I login as admin on Wi-Fi?

Go to Internet > Change WiFi Settings > Other Settings.
If you haven’t set a username and password yet, enter ‘admin’ and ‘password. ‘ Otherwise, use the ones you set. Tap Go to Admin Tool, then Advanced Settings

How do I find my router admin password?

These passwords are often printed on a sticker on the router. Try a common username and password combination. Many routers use the password ‘admin’ and a blank username. They can also use a blank password and ‘admin’ as the username, or ‘admin’ as both the password and username

Is it possible to hack WiFi password?

For very little money, a hacker can rent a cloud computer and most often guess your network’s password in minutes by brute force or using the powerful computer to try many combinations of your password. Your home Wi‑Fi network can easily be broken into if you have a weak password.

Can admin of PIX-LINK WiFi see my history?

Yes, depending on the router, the Wi-Fi owner could look up your browsing history through the router’s admin panel. They could check the router logs to see connected devices, timestamps, sources, and IP addresses, but not necessarily specific URLs.

Can you make your own Wi-Fi?

To create your own Wi-Fi network, you’ll need a wireless router. This is the device that will broadcast the Wi-Fi signal from your Internet modem throughout your house. Your Internet service provider (ISP) may offer you a wireless router for a small monthly fee.

VIDEO

PIX-LINK WR22 300Mbps WiFi Wireless Signal Amplification Enhancement Extender

Name	Statue	Indication
Power	On	The AC Mini Router is powered on.
	Off	The AC Mini Router is powered off.
WPS	Off	No active connection.
	Blinking	WPS connection is in progress.
LAN	On/off	The wireless signal is on/off.
WAN	On	The WAN port is connected.
	Off	The WAN port is disconnected.
	Flashing	Transferring data to/from a network device.
LAN	On	The LAN port is connected.
	Off	The LAN port is disconnected.
	Flashing	Transferring data to/from a network device.
Signal (Repeater Mode)		The AC Mini Router is connected to the router or AP but is too far near the router or AP.
		The AC Mini Router is connected to the router or AP and is in a good location.
		The AC Mini Router is connected to the router or AP but is too far away from the router or AP.

Button and Port Explanation

WPS Button:
If your host router supports the WPS function, you can press the WPS button and then press the WPS button of the AC Mini Router to establish a secure connection between the host router and the AC Mini Router.
Reset Button: This button is used to restore the AC Mi Ni Router’s factory default settings.
There are two ways to reset the AC Mini Router:
Option One: With the AC Mini Router powered on, use a pin press the Reset Button for less than 8 seconds, then release the button and wait for the AC Mi Ni Router to reboot to its factory default settings.
Option Two.: Restore the default setting from “Advanced-> System->Load default->Load default” of the AC Mini Router’s Web-based Management page.
WAN Port: One 10/1 OOMbps RJ45 Ethernet port.

• Router mode, it’s used for connecting to the DSL/cable Modem or Internet.
• Repeater/WISP mode, it’s used for connecting to an Ethernet-enabled device, working the same as the Ethernet port.
• Access Point mode, it’s used for connecting to the front router or Internet.

LAN Port: One 10/100Mbps RJ45 Ethernet port is used to add wireless connectivity to an Ethernet-enabled device such as Internet TV, DVR, gaming console, and so on. Please note that this port is not allowed to be connected to the router.

Quick setup using a web browser

Power on

Plug the AC Mini Router into an electrical outlet near your router. When the router boot is completed, the Signal LED is all on.

Connect to the AC Mi Ni Router

For Windows Users

Disconnect your Ethernet (wired) connection from your computer Click the Wi-Fi icon on the taskbar and connect to the Repeater’s network(e.g. Wireless-AC_2G/5G)

For Mac OS X Users

Disconnect the Ethernet (wired) connection from your computer (if any). Click the Wi-Fi icon in the top right corner of the screen, and connect to the Repeater’s network (e.g Wireless-AC_2G/5G)

For Wired

Disable the Wi-Fi on your computer. Connect your computer to the Repeater via an Ethernet cable

Configure the AC Mi Ni Router

1. Open a web browser and type http://myrepeater.net in the address field After a moment, alogin window will appear Select the language for the installation, and then enter admin for the Password, Then click the Submit button or press the Enter key to log in to
   Language – Select the Language from the drop-down list. The default setting is English
   Password -Enter the password for Login The default password is admin
2. After successful login, you can click the Wizard to quickly configure your router Select the Operation Mode you need and click Next to go on configuring

Gateway Mode(Default)

Stand Wireless Router Mode: This router connects to the Internet by WAN port, and then other terminal devices can connect to this router by wireless connection or connect to this router’s LAN port by wired.

If GateWay is selected, click the drop-down menu of WAN Mode, and then WAN Connection Type will appear, Select the very type go on configuring.

a. If the connection type is Dynamic IP Address,Please click Next to continue.

b. If the connection type is Static IP Address, the next screen will appear as shown below Configure the following parameters and then click Next to continue.

c. If the connection type is PPPoE, the next screen will appear as shown below Configure the following parameters and then click Next to continue.

IP Address – This is the WAN IP address as seen by external users on the Internet (including your ISP). Enter the IP address into the field.
Subnet Mask – The Subnet Mask is used for the WAN IP address, it is usually 255.255.255.0.
Gateway – Enter the gateway IP address into the box if required.
Primary DNS – Enter the DNS Server IP address into the box if required.
Secondary DNS(option) – If your ISP provides another DNS server, enter it into this field.
PPPoE User Name – Enter the User Name provided by your ISP.
PPPoE Password – Enter the Password provided by your ISP.

SSID(2G)/SSID(5G)- Enter a value of up to 32 characters. The same name of SSID(Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be Wireless-AC 2G and Wireless-AC 5G.
Security – you can choose the security type on the drop-down list. The default setting is OPEN.
Security key – Wireless Password, When WPA/WPA2PSK is set as the Security Type, You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters.
Enter SSID and Security, then click Apply to complete setup.
Note: Do not close this window, the window will automatically close when the setup is complete.

Wireless AP Mode

Traditional wired router realizes wireless function: This router can connect to uplink router’s LAN port by wired connection, the user terminal can connect to this router by wireless connection.

If Wireless AP Mode is selected, The Wireless settings page will appear as shown below.

S510(2G)/S51D(5G)- Enter a value of up to 32 characters. The same name of 55/D (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be Wireless-AC_2G and Wireless-AC_5G. Security you can choose the security type on the drop-down list. The default setting is OPEN.
Security key – Wireless Password, When WPA/WPA2PSK is set as the Security Type, You can enter ASCII characters between 8 and 63 characters or 8 to 64 Hexadecimal characters.
Enter SSID and Security, then click Apply to complete setup.

Wireless Repeater Mode

Extend wireless signal comprehensively This router can connect to the uplink wireless router by wireless connection, the user terminal can connect to this router by wired or wireless connection.

If Wireless Repeater Mode is selected, The Wireless Repeater(WDS) page will appear as shown below.

Select the SSID of the target network and insert Repeater SSID and the key of your network. the default Repeater SSID is set to be 00ox 2G Ext/ X0ox 5G Ext (xxxx indicates The Main Router’s wireless network name). Then click Apply to complete setup.
Note The Security Key is the same as your Wireless Router.

WISP Mode

Wireless used as WAN port: This router can connect to the uplink wireless router by wireless connection, at the same time, it can extend wireless signal for other device’s connection.

If WIPS is selected, The Wireless ISP (APClient) page will appear as shown below.

Select the SSID of the target network and insert Repeater SSID and the key of your network. the default Repeater SSID is set to be x0xx_2G_Ext/ xxxx_5G_Ext (xxxx indicates The Main Router’s wireless network name). Then click Apply to complete setup.
Note The Security Key is the same as your Wireless Router.

Quick setup Repeater Mode using WPS Button

WPS is an easier way to extend your host network. You are recommended to use this method if your host router has a WPS button.
Note: your host router should support WPS.
The button might look like one of these: . Otherwise, please setup Using a Web Browser.

Power on

Plug the AC Mini Router into an electrical outlet near your router. When the router boot is completed, the Signal LED is all on.

Connect

Press the WPS button on the AC Mi Ni router, and then press the WPS button on your Host Router within 2 minutes.

The WPS LED will be blink when pressing the WPS button, the xxXX_2G_Ext/xxxx_5G_Ext appear in your wireless network list, indicating a successful WPS connection,(XXXX indicates The Host Router’s wireless network name). If not, please use Web Browser setup.
Note: The Security Key is the same as your Host Router.

The WPS first connects to the 5GHz network, if you want to connect to the 2.4GHz network of your dual-band router, please use Web Browser setup.

Relocate

1. Plug the extender into an electrical outlet about halfway between your router and the Wi-Fi dead zone. The location you choose must be within the range of your host network.
   
2. Wait until the signal LED displays two or three lattice signals.
   If not, relocate it closer to the router to achieve better sig na I qua I ity.

Entertaubment Adapter

The MiNi Router can be used as a wireless adapter to connect any Ethernet-only device such as a Blu-ray player, game console, DVR, or smart TV to your Wi-Fi network. First, connect the Mi Ni Router to your router using Repeater Mode or WISP Mode. Then connect your Ethernet-only device to the MiNi Router via an Ethernet cable.

Change Default Access
Default Access of The AC Mini Router is http://myrepeater.net, and Default IP
The address of The AC Mini Router is 192.168.1.253.
Click “Advance -> Internet-> LAN Settings” located on the home page, the following message will be displayed on your web browser.

Click Apply to save the settings.
Note: If you change the IP Address of LAN or Domains, you must use the new IP Address or Domains to log in to the router.

Firmware Upgrade
The system software used by this AC Mini Router is called “firmware”, just like any application on your computer, when you replace the old application with a new one, your computer will be equipped with a new function. You can also use this firmware upgrade function to add new functions to your router, even fix the bugs of this router.

1. Click “Advance -> System -> Upgrade Firmware ” located on the home page, the following message will be displayed on your web browser.
   
2. Click the “Browse” button first; you’ll be prompted to provide the filename of the firmware upgrade file.
3. After a firmware upgrade file is selected, click the “Upload” button. and the AC MiNi Router will start the firmware upgrade procedure automatically. The procedure may take several minutes, please be patient.

Frequently Asked Questions (FAQ)

01. What should l do if I cannot access the Router’s web management page?

• If your computer is wirelessly connected, make sure that you have connected to the Router’s SSID.
• If your computer is connected via an Ethernet cable, please make sure that the connection is stable.
• Make sure your computer is set to obtain an IP address and DNS server address automatically.
• Verify that http://myrepeater.net or http://192.168.1.253 is correctly entered in the web browser and press Enter.
• Please reset the extender and try again.
  Q2. I have enabled a wireless MAC filter, wireless access control, or access control list (ACL) on my host router. What should I do before configuring and using the extender?
• If you have enabled those functions of your host router, you may need to disable them first. And then follow a quick setup to complete the configuration.

FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm the radiator your body: Use only the supplied antenna.