ALTOS CYCLING SHOE
Instruction Manual

WARNING: Read and follow all warnings and instructions before clipping in and out for the first time. Improper use may result in serious injury.
The information in this guide may not reflect recent updates as we continue to improve our product. Please see onepeloton.com/manuals for the latest version.
CAUTION: These shoes are designed for use with a Peloton Bike or Bike+ and the included Delta-compatible cleats only. They may not be compatible or safe for use with other equipment.
WARNING: Cycling barefoot or with inappropriate footwear can cause serious injury. Always use the Peloton Bike and Bike+ with cycling shoes equipped with appropriate cleats, or with equally supportive athletic footwear.

SETUP

Loosely attach the cleat and move it to your preferred position.

Then fully tighten the bolts.

TIP: If you are setting up up cycling shoes for the first time, we recommend that you start with the cleats pushed all the way back and adjust if you experience discomfort while riding.
See support.onepeloton.com for more information.

CAUTION: Make sure that your cleats are properly positioned and all bolts are fully tightened before clipping in. Check for and tighten loose pedals on a regular basis. Riding with loose cleats or pedals could lead to serious injury.

USE

CAUTION: Do not attempt to walk in cycling shoes with cleats. Wear cycling shoes only while using the Peloton Bike/Bike+ and remove them immediately after clipping out. Walking on cleats may cause you to fall or twist your ankle, or otherwise result in serious injury.

CAUTION: Be careful when clipping in and out. While you may need to use some force, excessive force or aggressive movements could result in an ankle, foot, or leg injury.

CLIPPING IN

Point your toes down to fit the cleat into the front of the pedal. Push down through your heel.

CLIPPING OUT

Kick your heel away from the bike.

LIMITED WARRANTY

For customers who reside and purchase a Peloton accessory in the United States, Canada, Germany, or the United Kingdom, Peloton warrants the components and all original parts against defects in workmanship and materials for a period of 12 months from the date of delivery, or for any additional period that is required by applicable law.
This voluntary Limited Home Use Warranty does not affect your statutory warranty rights but applies in addition to them.
For the complete Limited Warranty, visit onepeloton.com/warranty.

MANUFACTURED FOR
Peloton Interactive, Inc.
441 9th Ave, 6th Floor
New York, NY 10001
USA

BS03-01UB | 00041-4.0
©Peloton 2022, Peloton Interactive, Inc.
All rights reserved.
onepeloton.com | onepeloton.ca

Instruction for Use

Product Name: Peloton Heart Rate Monitor
Model No.: HRC01

PELOTON HEART RATE MONITOR
Peloton Interactive, Inc.
125 W 25th Street, 11FL, New York, NY 10001
www.onepeloton.com

READ IMPORTANT SAFETY INFORMATION ON REVERSE SIDE OF PAGE.
Follow all warnings and instructions.

USING THE PELOTON HEART RATE MONITOR

• Snap the sensor pod onto the chest strap.
• Adjust the strap to fit your lower chest. It should be snug but comfortable.
• When the heart rate monitor detects a heartbeat, the LEDs will flash red and blue. If your monitor does not detect your heartbeat, aid the connection by moistening the electrodes with a small amount of water, saliva, or electrode heart rate gel.
• Join a class. The heart rate monitor will connect to your Peloton product automatically via ANT+.

READING THE LED INDICATORS

• Flashing Red: The heart rate monitor detects a heartbeat. The LED will stop flashing after 30 seconds.
• Flashing Blue: The heart rate monitor detects a heartbeat and is in Bluetooth pairing mode. The LED will continue flashing until the monitor connects to a Bluetooth device, even if you connect to a Peloton product via ANT+.
• Flashing Yellow: The heart rate monitor’s battery is low. Replace immediately with a new CR2032 3-volt battery.

REPLACING THE BATTERY

• The right LED will flash yellow when the battery needs to be replaced.
• The battery door is located on the underside of the sensor pod. Unscrew it by inserting a coin into the slot and rotating it counterclockwise.
• When the battery door is loose, remove it. The battery sits inside the battery door.
• Wait for 20-30 seconds.Then insert a new CR2032 3-volt battery, with the flat side facing down.
• Place the battery door over the markers. Insert a coin into the door slot and rotate clockwise until the door is flush with the underside of the sensor pod.
• Test the heart rate monitor to make sure the sensor activates.

WARNING : Contact your local waste services provider to recycle coin cell batteries.
Batteries may contain perchlorate material and special handling may be required.
California customers: see www.dtsc.ca.gov/hazarouswaste/perchlorate

SPECIFICATIONS

Heart rate measurement range : 30 – 240 beats per minute (bpm)
Battery type :User replaceable CR2032 3 volts
Expected battery life : 600+ hours
Radio frequency protocol : 2.402 – 2.480 GHz (BLE) / 2.457 GHz(ANT+)
Water rating : IPX7 Water Resistant
Operating temperature range : 0 – 50°C/-32 – 122°F
Weight : 13 grams
Size (sensor pod only) : 64mm
Maximum output power : ‐1.27 dBm (BLE) / ‐1.44 dBm (ANT+)
Peak active current : Typical 7.5mA
Stand-by- current : Less than 10uA
Contains FCC ID : 2AA3NHRC01

IMPORTANT SAFETY INFORMATION

WARNING: Read all safety information before using your heart rate monitor.

Consult a doctor before beginning a new fitness plan. Incorrect or excessive training can result in serious injury.

If you have a pacemaker or other implanted electronic device, consult your physician prior to using a heart rate sensor.

Contains coin cell battery, can be fatal if swallowed. Keep batteries away from children. Do not swallow. Swallowing can lead to chemical burns, perforation of soft tissue, and death. Fatal burns from batteries lodged in throat can occur in as little as 2 hours.

If you experience faintness, chest pain, or shortness of breath, stop exercising immediately and consult a doctor.

Heart rate and other measurements may be inaccurate. Use for reference or information only.The heart rate sensor is not a medical device. Readings could be influenced by interference from other devices or sources.

Only use correct replacement batteries. Others pose fire and explosion hazard.

SAVE THESE WARNINGS AND INSTRUCTIONS.

EU RADIO EQUIPMENT DECLARATION OF CONFORMITY

Hereby, Peloton declares that the radio equipment type HRC01 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: www.onepeloton.com/ compliance.

WARNING :This product can expose you to chemicals, including Lead, Nickel, and Acrylonitrile, which are known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

FCC RULES PART 15

The enclosed product (hardware) device complies with part 15 of the FCC Rules. Operation is subject to following two conditions: (1) this device may not cause harmful interference and (2) it must accept any interference received, including interference that may cause undesired operation.

MODIFICATION STATEMENT

This device has been designed to comply with the FCC Rules. Changes or modifications not expressly approved could void the user’s authority to use the device.

FCC RADIATION EXPOSURE STATEMENT

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be re-located or operated in conjunction with any other antenna or transmitter.

FCC COMPLIANCE STATEMENT

This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or television equipment reception, which can be determined by turning the equipment off and on, the user is encouraged to try correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

PELOTON Original Bike Cycling Shoes

Introduction

WARNING: Read and follow all warnings and instructions before clipping in and out for the first time. Improper use may result in serious injury.
The information in this guide may not reflect recent updates as we continue to improve our product. Please see onepeloton.com/manuals for the latest version.
CAUTION: These shoes are designed for use with a Peloton Bike or Bike+ and the included Delta-compatible cleats only. They may not be compatible or safe for use with other equipment.

S TE P 1

Loosely attach the cleat and move it to your preferred position.

T I P: If you are setting up up cycling shoes for the first time, we recommend that you start with the cleats pushed all the way back and adjust if you experience discomfort while riding. See support.onepeloton.com for more information.

CAUTION: Make sure that your cleats are properly positioned and all bolts are fully tightened before clipping in. Check for and tighten loose pedals on a regular basis. Riding with loose cleats or pedals could lead to serious injury.

CAUTION: Do not attempt to walk in cycling shoes with cleats. Wear cycling shoes only while using the Peloton Bike/Bike+ and remove them immediately after clipping out. Walking on cleats may cause you to fall or twist your ankle, or otherwise result in serious injury.

S TE P 2

Lift the ratchet to tighten the strap.

CAUTION: Be careful when clipping in and out. While you may need to use some force, excessive force or aggressive movements could result in an ankle, foot, or leg injury.

STEP 3

CLIPPING IN: Point your toes down to fit the cleat into the front of the pedal. Push down through your heel.

CLIPPING OUT: Kick your heel away from the bike.

LIMITED WARRANT Y

For customers who reside and purchase a Peloton accessory in the United States, Canada, Germany, or the United Kingdom, Peloton warrants the components and all original parts against defects in workmanship and materials for a period of 12 months from the date of delivery, or for any additional period that is required by applicable law. This voluntary Limited Home Use Warranty does not affect your statutory warranty rights but applies in addition to them.
For the complete Limited Warranty, visit onepeloton.com/warranty.