OTBeat Burn

Getting Started

1. Included in packaging: OTbeat Burn, SM band, LG band, & USB cord
2. Remove OTbeat Burn from the packaging
3. Connect the USB cord into charging port of device
4. LED light will appear after a few seconds

Downloading the Orangetheory App

Using your mobile device, download the Orangetheory App.

Note: Fully charge device before attempting to pair for the first time.

Charging The Device

1. Open rubber port cover on back of device
2. Plug in mini-USB connector into device port
3. Plug in regular USB connector into charging block
4. Plug in charging block into wall outlet

Device can be connected directly to a computer USB port. Note: The voltage differs from wall outlet to computer.

Battery is fully charged when Green LED is continuously on During charging: Red LED light will blink slowly LED indication for charging is in front of device

Proper Placement

To transmit accurate data from your device:

1. Fasten device snugly in one of the below placement options
2. Wear device below, and not directly on top, of wrist bone* or elbow
3. The optical sensor on the back should make good contact with skin

*For placement on wrist, measure two fingers above wrist bone

Pairing Device

1. Once OTbeat Burn is fully charged, press center of splat to power ON the device

2. Launch the settings app on your mobile device
3. Ensure your Bluetooth settings are on

4. Open Orangetheory app on mobile phone.

5. Use the Orangetheory app to search for device

*Once the device appears, OTbeat Burn is successfully connected to app

LED Guide

Heart Rate Detection LED Indication:

• Alternating BLUE and GREEN: Detecting heart rate
• Alternating BLUE and RED: No heart rate detected
• Blinking GREEN: Heart rate detected
• Blinking ORANGE: Heart rate zones are changing

Bluetooth Connection State:

• Blue LED blinks for 5 seconds: After turning on the unit
• Blue LED continuously on for 5 second: Connected
• Green LED on for 2 seconds: Connected (HR not detected)
• Green LED continuously on: Updating firmware

Battery LED Light

During Charging

Red LED blinks slowly: Charging

Green LED continuously on: Battery full

Battery State

Red LED blinks three times: Low battery at <15% (repeat every 5 min. until reach critical level)

Red LED continuously on for 2 sec: Device powering off

Caring for Device

1. To ensure accurate readings, clean the sensor lens with a soft cloth
2. OTbeat Burn unit and strap are waterproof to IP67 specifications and can be easily cleaned with mild soap and cool water
3. Use a cotton swab and only rubbing alcohol to clean the USB charging contacts when necessary: do not contact USB charging port
4. Do not use any abrasive chemicals to clean the Otbeat Burn unit, sensor, or strap. This will cause permanent damage

Technical Specifications

For more information visit orangetheoryfitness.com/otbeat

USER MANUAL

OTBeat Core Monitor

Thank you for selecting this product as your heart rate monitor of choice. This product will track your data in real time during your Orangetheory® Fitness Workout and is also compatible with the Orangetheory Fitness mobile app on your smart phone.

IMPORTANT: This product is for recreational purposes only and is not meant to replace any medical device.

This manual contains important safety and care information, and provides step-by-step instructions for using this product. Read this manual thoroughly, And keep it in a safe place for future reference.

Device Overview

A. Heart Rate Transmitter

1. Left & Right Strap Connectors
2. Battery Cover

B. Chest Strap

3. Snap-On Button Connectors

4. Conductive Pads

GETTING STARTED

A. Unpacking the Product
In this box, you will find:

• 1 – Heart Rate Transmitter
• 1 – Adjustable Elastic Strap
• 1 – CR2032 Battery (installed)
• 1 – User Manual

How to Wear the Chest Strap

1. Wet the conductive pads on the strap with a few drops of water or conductive gel to ensure direct contact to the skin.

2. Secure the strap across your chest. To ensure an accurate heart rate signal, adjust the strap until it fits snugly below your chest (pectoral muscles).

3. Attach the transmitter to the strap, matching up the connector snaps (see image on page 4).

4. Make sure the Orangetheory® Fitness logo is facing right side up and the arrows on the back of the transmitter are pointed up when the strap is being worn.

WARNING: Inaccurate heart rate data will be detected if the transmitter is worn upside down.

WARNING:

1. Do not clean the transmitter or strap in a washing machine or dryer.
2. Before hand washing the strap, detach the transmitter pod from the snaps.
3. The transmitter pod should not be washed. To clean the pod, wipe with a damp cloth. Ensure the pod is fully dry before using.
4. While washing the strap, make sure water is no warmer than 86°F.
5. Ironing, bleaching or heating will damage the strap and pod.

BATTERY

The transmitter uses one CR2032 3V battery. The battery is already installed, and typically lasts one year. If you need a new battery, we recommend that you contact your studio to purchase a replacement.

REPLACING YOUR BATTERY

A. Remove the battery cover and set aside.

B. Remove the old battery and insert the new battery with the (plus) side facing up.
C. Install the battery cover back into place by pressing the battery cover down.

IMPORTANT

1. Batteries must be disposed of properly. Please check your local waste disposal guidelines for proper battery disposal procedures.
2. Batteries are extremely dangerous if swallowed. Therefore, keep batteries and any small articles included with this product away from children. If a battery or small article has been swallowed, seek immediate medical attention.
3. The battery supplied should not be recharged, reactivated or dismantled. Keep batteries away from fire.

PAIRING

1. On your mobile device, download the Orangetheory Fitness mobile app.
   
2.  Sign into the Orangetheory Fitness mobile app using your member credentials.
3. Once signed in, navigate to the Settings page by tapping the gear icon. Then, tap “Add Device.” Make sure Bluetooth is enabled on your mobile device.
4. Tap “Search for a device.”
5. Once your transmitter has been found, tap to select and complete pairing. If the pairing fails, you will see an error message prompting you to try again.

DATA TRANSMISSION

This ANT+ & Bluetooth transmitter pod is designed to acquire and transmit heart rate data.

For more information visit
ORANGETHEORY.COM