NEXA Relay For Wall Socket
THIS PRODUCT SUPPORTS SMART MODE.
Devices that support Smart Mode can save up to 3 different favourite scenarios, and these can be activated easily using a Nexa Smart Mode transmitter.
Built-in receiver, which makes your socket outlet wireless. The receiver needs both phase and neutral. The receiver is fully compatible with other System Nexa products.
SAFETY
Read through the entire instruction first. Engage a professional if so required. Nexa cannot be held liable if the product is used for any purpose other than the one for which it is designed, or if there is failure to comply with the instruction. Never connect bulbs or equipment exceeding the receiver’s maximum stated load – this may lead to faults, short-circuiting or fire.
Do not attempt to repair the product. The product contains no repairable parts.
INSTALLATION
Make sure that the conductors are powered down by turning off the power in the distribution box.
Connect the MSOR-3500 according to the wiring diagram. Note, do NOT disconnect protective earth lead from the electrical outlet.
PROGRAMMING
- Power up MSOR-3500
- Press the learn button, the LED indicator starts to flash
- Press the “ON” button for the selected channel on a System Nexa remote control within 12 seconds.
PROGRAMMING CONFIRMATION
The LED indicator on the receiver flashes rapidly.
DELETING A MEMORY SLOT
- Power up MSOR-3500
- Press the learn button, the LED indicator starts to flash
- Press the “OFF” button for the selected channel on a System Nexa remote control within 12 seconds
CONFIRMATION OF DELETION
The LED indicator on the receiver flashes rapidly.
DELETING ALL MEMORY SLOTS
- Power up MSOR-3500
- Press and hold down the learn button for 6 seconds, the LED indicator starts to flash.
- Release the learn button and then press it again briefly. All storage locations are now deleted.
MEMORY SLOTS
Every MSOR-3500 receiver has 32 storage locations. When storage location 32 is occupied, location 1 is overwritten during programming.
CONTROL
The receiver can be controlled in a number of ways.
- With a programmed System Nexa remote control
- With other programmed System Nexa transmitters
- With a Nexa Bridge.
SAFETY INSTRUCTIONS AND INFORMATION
Indoor range: up to 30 m (optimal conditions). The range is strongly dependent on local conditions, such as the presence of metals. For example, the thin metal coating in Low-emissivity (Low-E) glass has a negative impact on the range of radio signals.
There may be restrictions on the use of this device outside the EU. If applicable, check whether this device complies with local directives.
Maximum load:
Never connect lights or equipment that exceed the maximum load of the receiver, as it can result in defects, a short circuit or fire.
Life-support:
Never use Nexa products for life-support systems or other applications in which equipment malfunctions can have life-threatening consequences.
Interference:
All wireless devices may be subject to interference, which could affect performance. The minimum distance between 2 receivers should be at least 50 cm.
Repairing:
Do not attempt to repair this product. There are no user-serviceable parts inside.
Water-resistance:
This product is not water-resistant. Keep it dry. Moisture will corrode the inner electronics and can result in a short circuit, defects and shock hazard.
Cleaning:
Use a dry cloth to clean this product. Do not use harsh chemicals, cleaning solvents, or strong detergents.
Environment:
Do not expose the product to excessive heat or cold, as it can damage or shorten the life of electronic circuit boards.
WIRING DIAGRAM
LCMR-1000
RELAY, 1 CHANNEL
TECHNICAL DATA
| LCMR-1000 | |
| Power source | 220-240 V~50 Hz |
| Max. charge | 2300 W / 10A |
| Frequency | System Nexa (433.92 MHz) |
| Range | up to 30 m |
| Storage locations | 6 |
| Power consumption | < 1 W (standby) |
| Operating temperature | 0-40 °C |
| IP rating | IP20 Indoor use |
| Dimensions | 53 x 53 x 25 mm |
A declaration of conformity is available at www.nexa.se
NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN
[email protected] | www.nexa.se
Built-in receiver for wireless control of lamps, etc. The receiver needs both phase and neutral. The receiver is fully compatible with other System Nexa products.
SAFETY
Read through the entire instruction first. Engage a professional if so required. Next cannot be held liable if the product is used for any purpose other than the one for which it is designed, or if there is failure to comply with the instruction.
Never connect bulbs or equipment exceeding the receiver’s maximum stated load – this may lead to faults, short-circuiting, or fire. Do not attempt to repair the product.
The product contains no repairable parts.
INSTALLATION
Make sure that the conductors are powered down by turning off the power in the distribution box.
Connect LCMR-1000 as shown in the wiring diagram.
LINKING
To control LCMR-1000 using a System Nexa remote control (or other devices), the transmitter and receiver must be linked as follows:
- Power up LCMR-1000
- Press the learn button, the LED indicator starts to flash slowly
- Press the “ON” button for the selected channel on a System
Next: remote control within 18 seconds
See the instructions for use for the product in question if you wish to train other System Nexa devices (motion detector, magnetic contact, bridge, etc.)
LINKING CONFIRMATION
The relay in LCMR-1000 clicks 4 times, and any connected lamp flashes twice.
DELETING A STORAGE LOCATION
- Power up LCMR-1000
- Press the learn button, the LED indicator starts to flash slowly
- Press the “OFF” button for the selected channel to be deleted on a System Nexa remote control within 18 seconds.
See the instructions for use for the product in question if you wish to delete other System Nexa devices (motion detector, magnetic contact, bridge, etc.)
DELETION CONFIRMATION
The relay in LCMR-1000 clicks 4 times, and any connected lamp flashes twice.
DELETING ALL STORAGE LOCATIONS.
- Power up LCMR-1000
- Press and hold down the learn button for 6 seconds, the LED indicator starts to flash quickly
- Release the learn button and then press it again briefly.
CONFIRMATION OF DELETION OF ALL STORAGE LOCATIONS
The relay in LCMR-1000 click 4 times, and any connected lamp flashes twice.
STORAGE:
LCMR-1000 has 6 storage locations and can be controlled from up to 6 different devices (remote controls, motion detectors, magnetic contacts, bridges, etc.). If all storage locations are occupied, it is not possible to train a new device without deleting a storage location first: see “DELETING A STORAGE LOCATION”
CONTROL
The receiver can be controlled in a number of ways.
- With a trained System Nexa remote control
- With other trained System Nexa transmitters
- With a Nexa Bridge
FUSE
LCMR-1000 is provided with a glass tube fuse, 250V/T5A, which provides overload protection. If the fuse is broken, check the connected device for faults or short-circuit first before replacing the fuse and powering LCMR-1000 back up.
OTHER INFORMATION
Indoor range: up to 30 m (optimal conditions). The range is strongly dependent on local conditions, such as the presence of metals. For example, the thin metal coating in Low- emissivity (Low-E) glass has a negative impact on the range of radio signals. There may be restrictions on the use of this device outside the EU. If applicable, check whether this device complies with local directives.
Maximum load: Never connect lights or equipment that exceed the maximum load of the receiver, as it can result in defects, a short circuit, or fire.
Life-support: Never use Nexa products for life-support systems or other applications in which equipment malfunctions can have life-threatening consequences.
Interference: All wireless devices may be subject to interference, which could affect performance. The minimum distance between 2 receivers should be at least 50 cm.
Repairing: Do not attempt to repair this product. There are no user-serviceable parts inside.
Water-resistance: This product is not water-resistant. Keep it dry. Moisture will corrode the inner electronics and can result in a short circuit, defects, and shock hazard.
Cleaning: Use a dry cloth to clean this product. Do not use harsh chemicals, cleaning solvents, or strong detergents.
Environment: Do not expose the product to excessive heat or cold, as it can damage or shorten the life of electronic circuit boards.
WIRING DIAGRAM
NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN
[email protected] | www.nexa.se
NEXA LED 12-24v Dimmer Module
Dimmer receiver for permanent installation with adjustable minimum brightness. Suitable for dimmable LED strip and LED luminaires with a built-in 12-24 V driver
SAFETY
Read through all of the instructions first. Call in a professional if necessary. Nexa cannot be held liable if the product is used for any purpose other than the one for which it is designed, or if there is failure to comply with the instructions. Never connect bulbs or equipment exceeding the receiver’s maximum stated load – this could lead to faults, short-circuiting or fire. Do not attempt to repair the product. The product contains no repairable parts
INSTALLATION
Connect the positive conductor from the voltage source (AC/DC adapter) to + and the negative conductor to – on DC in, the load’s positive conductor + and negative conductor to – on DC out on the LDR-075. See also wiring diagram.
LINKING
- Power up the LDR-075
- Press the learn button, the LED indicator will start to flash
- Press the “ON” button for the selected channel on a System Nexa transmitter within 15 seconds.
LINKING CONFIRMATION
The LED indicator lights steadily, if there is a bulb connected to the receiver it will flash twice.
DELETING A MEMORY SLOT
- Press the learn button
- Press the “OFF” button for the selected channel on a System Nexa transmitter within 15 seconds.
DELETION CONFIRMATION
The LED indicator lights steadily, if there is a bulb connected to the receiver it will flash twice.
DELETING ALL MEMORY SLOTS.
- Press and hold down the learn button for 6 seconds, the LED indicator starts to flash rapidly.
- Release the learn button and then briefly press it again.
CONFIRMATION OF THE DELETION OF ALL MEMORY SLOTS
The LED indicator lights steadily, if there is a bulb connected to the receiver it will flash twice.
MEMORY
The LDR-075 has 6 memory slots which means that it can be controlled by up to six transmitters at the same time.
DIMMER SETTINGS
There are a total of four levels for lowest dimmer level where 4 is the lightest and 1 the darkest. The receiver is supplied set to the highest level (4).
SET THE LOWEST DIMMER LEVEL
- Light the connected lamp using the transmitter
- Press the training button twice. The LED indicator starts to flash and the connected lamp dims to the lowest level currently set
- Press the “OFF” button for the selected channel on the transmitter to lower the level one step and “ON” to raise the level one step
- Press the training button twice to confirm the selected dimmer level
If the connected bulb starts to flicker or goes out completely, go back one step in the lowest dimmer level settings.
SETTING THE LOWEST DIMMER LEVEL CONFIRMATION
The LED indicator lights steadily, if there is a bulb connected to the receiver it will flash twice.
CONTROL
The receiver can be controlled in a number of ways.
- Using a trained System Nexa remote control
- Using other trained System Nexa transmitters
- Using a Nexa Bridge
OTHER INFORMATION
Range indoors: up to 30 m (optimal conditions). The range is very dependent on local conditions, if there is metal in the vicinity for example. The thin metal coating in low emissivity energy glass has a negative effect on the range of radio signals for example. There may be restrictions on the use of the unit outside the EU. If appropriate, you should check that the unit complies with local regulations.
Max. load: Never connect bulbs or equipment that exceed the maximum load of the receiver. This could lead to faults, short-circuiting or fire.
Life-support equipment: Never use Nexa’s products for life-support equipment or other devices where faults or interference could have life-threatening consequences.
Interference: All wireless units can suffer from interference that can affect performance and range. Because of this, the minimum distance between two receivers should be at least 50 cm .
Repair: Do not attempt to repair the product. It does not contain any repairable parts.
Water tightness: The product is not waterproof. Make sure it remains dry at all times. Damp will cause the internal electronics to corrode and this could lead to short-circuiting, faults and a risk of electric shock.
Cleaning: Clean the product using a dry cloth. Do not use chemicals, solvents or strong cleaning agents.
Environment: Do not expose the product to intense heat or cold as this could damage or shorten the service life of the electric circuits.
