MOONS Intelligent indoor LED driver MU050S150BQI201 Manual

ItsManual — Tue, 08 Aug 2023 17:53:32 +0000

MU050S150BQI201 Intelligent indoor LED driver

Features

Input voltage: 100-277Vac ，140-388Vdc
Built-in active PFC function 0.95 Typ.
High efficiency: up to 87% Typ.
Constant current, 2 channels output
2 channels 0-10V control
4 in 1:Tunable white(1500-6500K).Dim to warm(1500-3200K), Solo dimming, Dual dimming
The output current can be set from 150~1500mA
AUX output 12V,150mA
Protection: OVP, SCP, OPP, OTP
According to UL Class2、EN SELV
5-year warranty

Specification

Model (MU050S150BQI201 )
	Efficiency(230Vac)	87% (Typical) at 55V/0.911A load condition
	Efficiency(120Vac)	87% (Typical) at 55V/0.91A load condition
	Voltage Range	90-305Vac , 126-427Vdc
	Rated Input Voltage	100-277Vac , 140-388Vdc
	Frequency Range (Hz)	50/60
	Power Factor	>0.9 at 100-277Vac 50/60Hz input, with 50%–100% load conditions
	THD	< 20%, at 100 — 277Vac 50/60Hz input, with 50% — 100% load conditions
	AC Current(Typ.)	0.55A MAX at 120VAC , 0.3A MAX at 230VAC
	Inrush Current(Typ.)	<10A at 100 –277Vac input 25t cold start at 100% conditions .for more details in the attached graph
	Input Power (W)	60(max)
	Standby power (W)	<0.5W at input 120Vac, 230Vac
	Leakage Current(max.)	0.75mA at 277Vac 60Hz input
Output	Output Voltage Range (V) ,Note.1	8-55
	Output Current Range(mA)	150-1500.Support hot plug, without overshoot current .
	Rated Power (W)	50(max)
	Output channels	2
	Ripple Current	Output current 200-1500mA ripple LF(<120HZ) C 3 % Ripple = peak / average: ripple HF C 30 %
	Current Tolerance	±5%
	Line Regulation	±1%
	Load Regulation	±3%
	Setup, Rise Time	<0.5S @120V/60HZ, 230V/50HZ
	AUX output	12V± 3% ,150mA max
Dimming Control		Output current ..1mA
		Isolated 0-10V dimming / 0.1%lo-100%lo ref. Dimming module diagram and dimming curve
Protection	Open circuit protection(V)	60
	Short Circuit	Power supply stops output, recovers automatically when fault condition removed
	Over Power	Solo&Dual dimming the current drops by 5% per 100ms; Tunable white&Dim to warm each time drops 10%
	Over Temperature	tc 10000 ± 10%. Hiccup mode,When the temperature of tc rise to 100t (Typ.)
Environment	Operating Temp.	-25—+65t ; tc 90t:
	Operating Humidity	20-95%RH, non-condensing
	Storage Temp., Humidity	-40—+85°C, 10-95%RH
	Vibration	10-500Hz, 5G 12min/cycle, period for 72min each along X, Y, Z axis
	Ingress Protection Rating	IP20
Safety & EMC	Safety Standard	UL8750, CSA C22.2 No.250.13-14, EN61347-1, EN61347-2-13
		Isolation	Input	Output	Dimming interface	Enclosure
		Input	No applicable	3.75KV	3KV	1.875KV
		Output	3.75KV	No applicable	500V	1.5KV
		Dimming interface	3KV	500V	No applicable	500V
		Enclosure	1.875KV	1.5KV	500V	No applicable
	Isolation Resistance	I/P-0/P ,l/P-FG,0/P-FG:100M Ohms/500VDC/25°C/70%RH
	EMC Emission	FCC Part 15 ClassB, EN55015, EN61000-3-2 Class C, EN61000-3-3
	EMC Immunity	EN61000-4-2,3,4,5,6,8,11, EN61547 ( Surge L,N-FG 2KV. L-N 1KV) Additional suger test L,N-FG 2.5KV;L-N 2.5KV
Others	Life time	>50000 hours@Tc =75°C at 100% load conditions
	MTBF	300,000 hours, measured at full load, 25°C ambient temperature MIL-HDBK-217F(25°C)
	Dimension ( LxWxH )	408 x 30 x 21 mm / 16.06 x 1.18 x 0.83 in
	Weight	420g
Note.1: refer to V/I curve

Curve

Derating Curve

V/I Curve

PF VS. Load Curve

THD VS. Load Curve

Efficiency VS. Load Curve

0-10V dim Curve

Inrush current waveform

Inrush current information

Input voltage	Ipeak	Time@50% of Ipeak
120VAC	1.15	50us
220VAC	2.48	50us
277VAC	2.85	60us

Max number of drivers per MCB

Item	Max. number of drivers
Input voltage [VAC]	120	220	277
MCB B type 10A	16	30	34
MCB B type 13A	21	38	45
MCB B type 16A	26	47	56
MCB B type 20A	32	59	70
MCB B type 25A	40	74	87

Application of introduction

1. MCS interface(MCS+/MCS-)

MCS+ interface voltage 15V
Max current setting(each step is 1 mA), default driving current defined as 350mA.
Log or linear dimming curve, the default setting is log dimming.
NTC thermal management protects LED lamps, when the temperature of the LED lamp is over-temperature protection point, the current will be reduced by 50% every 5 minutes. The default setting is 85℃.

NTC compatibility list	NTC Manufacturer	NTC Model NO.
	MURATA	NCP21WB473J03RA
	VISHAY	NTCS0805e4473JXT
	VISHAY	NTCLE100E3473

Control the status of Auxiliary power when dim level =0. Enable standby mode: when dim level =0, the Auxiliary power will be closed. Disable standby mode: when dim level =0, the auxiliary power still can work. The default setting is enabled.
update Online, use the smart key to connect the PC and the driver to update the firmware.

2. Dimming performance

When changed to any dimming level, flicker wouldn’t occur, dimming would be achieved smoothly.
In the range of 200~1500mA, the current operating in continuous mode; In the range of 0~200mA, the current operating in PWM dimming mode, and the PWM frequency 3.6KHZ.

3. Guide for setting driver’s parametersTouch setting

Touch Setting Program driver’s parameters quickly and easily through Near Field Communication. Software download link:
http://leddriver.moons.com.cn/SouProduct/UCenter/M_Search/Software_view.aspx?MATNR=TouchSetting&rnd=1411
Smartkey Network Driver’s parameters can be set through Smartkey Ver.A1 and Smartkey Network. What’s more, the drive’s firmware can be used updated through this tool.
http://leddriver.moons.com.cn/SouProduct/UCenter/M_Search/Software_view.aspx?MATNR=SmartkeyNetwork&rnd=1411

4. Tunable white, Dim to warm, Solo dimming, Dual dimming function introduction

Tunable white	Cold color channel	CH1	Control port	DIM+CCT
	Warm color channel	CH2

Dim to warm	Cold color channel	CH1	Control port	DIM
	Warm color channel	CH2

Solo dimming	One 0-10V port control two output channels
Dual dimming	Two 0-10V ports control two output channels

Mechanical Specification

Dimensions(Unit:mm)

Port:

RoHS Compliance:
Our products comply with the European Directive 2002/95/EC, calling for the elimination of lead and other hazardous substances from electronic products.