MATTRESS FIRM 300

INSTALLATION

STEP 1
Remove the top of the shipping carton. Verify contents; inspect for damage.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING: DUE TO THE RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE THE ADJUSTABLE BASE.
SETUP

STEP 2
Cut zip-tie from the electrical power supply. Cut (2) zip-ties and remove mattress retainer (set aside) (FIGURE 1).

CAUTION
BE CAREFUL USING SHARP INSTRUMENTS. INJURY IS POSSIBLE IF TOOLS ARE NOT USED PROPERLY.

WARNING
PINCH POINT WARNING! KEEP HANDS AND FINGERS CLEAR WHEN SLIDING BASES TOGETHER.

STEP 3
Carefully lift the base head section out of the shipping carton and place it on a clean surface (FIGURE 2). Remove the divider from the shipping carton. Carefully lift the base foot section out of shipping carton and place adjacent to the head section (FIGURE 2). Slide head and foot sections together making sure to align mounting holes (center of base sections) (FIGURE 2).

STEP 4
Place a T-Spacer in between the mounting points (each side of the base). Line up the holes in the T-Spacers with the holes in the mounting points (FIGURE 3).
Place a center support bracket over the mounting points on each side of the base. Insert carriage bolts through the square holes in the center support bracket. Install nuts on carriage bolts (FIGURE 3).

HAND TIGHTENS.
After all, hardware is installed, tighten all nuts using the provided wrench.

STEP 5
Route FOOT MOTOR CABLE underneath the base frame and connect to HEAD MOTOR CABLE (FIGURE 4). 600 MODEL ONLY – Route FOOT MASSAGE MOTOR CABLE underneath the base frame and plug into control box (FIGURE 4). Extend electrical power cord out the head end of the base.

WARNING
POWER CORDS MUST NOT INTERFERE WITH ANY ADJUSTABLE BASE MECHANISMS.

STEP 6
Screw (4) legs into the threaded inserts at the corners of the base frame (FIGURE 5).
Screw (2) legs into the threaded inserts of the center support brackets (FIGURE 5).
Push the pin in to adjust leg height (6 inches to 10 inches).

Note: When adjusting legs, make sure the base sets level on the floor.

STEP 7
Rotate the base over onto its legs. Remove remaining packaging.

WARNING
DUE TO THE RISK OF INJURY, TWO ADULTS ARE REQUIRED TO HANDLE AND MOVE THE ADJUSTABLE BASES.

STEP 8
Install (3) batteries in the remote control. Plug the power cord into a power outlet.

Note: An electrical surge protection device is recommended (not included). Operate remote control to test base functions (FIGURE 6) (see separate Syncing Guide).

STEP 9
Lower base to flat position.

STEP 10
Install the mattress retainer at the foot end of the base. Place one end of the mattress retainer into the outside hole of the left insert and place the other end into the outside hole of right insert (FIGURE 7).

STEP 11
Place the mattress on the base to complete assembly.

Note: If the adjustable base will not operate, refer to the Troubleshooting section of the owner’s manual. To download a copy of the owner’s manual, visit https://lpadjustablebeds.com/om/mattressfirm or call Mattress Firm at 844-628-8376. To register your adjustable base, please go to https://lpadjustablebeds.com/register or call Mattress Firm at 844-628-8376.

FAQ’S

Can you use an adjustable base with a firm mattress?

The short answer is yes. There are many mattresses that can work with adjustable beds. However, there are some mattresses that won’t be compatible with this bed type. In general, all memory foam, latex, and any other non-innerspring mattress will work well with adjustable beds.

What are the disadvantages of an adjustable bed?

Cons: Disadvantages of Adjustable Beds
Higher costs. Adjustable beds tend to be more expensive than traditional ones.
Increased noise.
Extreme heaviness.
Restricted movement.
Unique sizing categories.

What causes an adjustable bed to stop working?

Sometimes a circuit in your home’s electrical wiring shorts out, causing the problem. Try using a different outlet nearby to see if it works. It is also possible that the bed’s wiring is faulty and needs to be replaced. If your bed is under warranty, most retailers will replace the parts free of charge.

Can an adjustable bed cause back pain?

The simple answer is yes. Sleeping on an adjustable bed can worsen back pain. There are three main ways in which a home hospital bed can make back pain worse: The bed’s adjustments are not used to distribute forces in a way to relieve pressure on affected areas of the back.

Do adjustable beds need maintenance?

Adjustable beds have motors, gears and moving parts that will eventually wear out and need to be repaired or replaced. The best adjustable beds come with warranties to help offset these costs, but you should know that the costs of maintaining an electric bed are typically more than that of a stationary one.

Do adjustable beds need oiling?

The lift motors are permanently lubricated and sealed no additional lubrication is required. Do not apply lubricant to lift motor lead screws or any nylon nuts or the base may inadvertently creep downward from the elevated position.

Why is my adjustable bed so loud?

An adjustable bed on a steel bed frame, wooden bed frame, wooden supports, or steel supports can cause excess noise due to the vibration of the framing. Eliminating as many points of contact as possible will cut down on excess noise.

How do I connect my mattress Firm 300 remote?

After five seconds it’ll start to rapidly flash when it’s flashing go ahead and press a button on the remote. Let go and press it again to connect

How do I turn off the child lock on an ease remote?

To disable child lock:
Press and hold the FOOT UP and FOOT DOWN buttons together for approximately three (6) seconds. The remote backlight will flash twice. When the backlight goes away the remote is no longer in Child Lock. The remote and adjustable base will work normally.

Why is my bed remote blinking?

The remote backlight will flash twice. When the backlight goes away the remote is now in Child Lock. Pressing any buttons while in Child Lock will yield no movement to your adjustable base. Press and hold the FOOT UP and FOOT DOWN buttons together for approximately six (6) seconds.

Is it OK to sleep on your side in zero gravity position?

Zero gravity allows your spine to stay in alignment even when you are sleeping on your side. An adjustable base can also help alleviate stress on your shoulders that you may experience from sleeping on your side on a traditional mattress.

Is it OK to leave adjustable bed in upright position?

The beauty of an adjustable base is to elevate the mattress to your comfort level while you use it. For long-term durability reasons, we don’t recommend storing your mattress in the elevated position when it isn’t actively in use. Instead, make sure it is entirely flat.

MATTRESS FIRM MFI131970 600 Adjustable Base Remote

Size

Remote control button diagram

Remote control function description

Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

MATTRESS FIRM RF510A Remote Control

Button Of Remote

ITEM

1. Child Lock 18
   Click the Child Lock button for 3 seconds to lock or unlock the remote.
2. Bed lamp 7
   Click the bed lamp button to open or shut the light under the bed.
3. Antisnore 16
   Click the Anti snore button, the bed moves to Anti snore position, press and hold Anti snore
   button for 5s, until the backlight flashes, the control set the current position as Anti snore position
4. TV 15
   Click the TV button, the bed moves to TV position, press and hold the TV button for 5s, until
   backlight flashes and the control set the current position as the TV position.
5. HEAD AND FOOT UP 5
   Press the head and foot up button, head and foot actuator moves out, stops when released.
6. HEAD AND FOOT DoWN 6
   Press the head and foot down button, head and foot actuator moves in, and stops when released.
7. M1 20
   Click the MI button, and the bed moves to the MI position, press and hold the MI button for Ss until
   backlight flashes, the control set the current position as MI position
8. HEAD-UP 1
   Press and hold the HEAD-UP button, the head actuator moves out, stops when released.
9. HEAD DOWN 2
   Press and hold the HEAD DOWN button, the head actuator moves in, stops when released.
10. FOOT UP 3
    Press and hold the FOOT UP button, foot actuator moves out, stops when released.
11. FOOT DOWN 4
    Press and hold FOOT DOWN button, foot actuator moves in, stop when released.
12. ZG 17
    Click the ZG button, and the bed moves to zero position, press and hold the zero buttons for 5s,
    until the backlight flashes, the control set the current position as zero position
13. HEAD MASSAGE 9,10
    Click the HEAD MASSAGE button, head massage motor switches massage intensity, massage
    intensity switches among 0-1-2-3:
14. MASSAGE model 14
    Click the MASSAGE MODEL button to change the massage model.
15. FOOT MASSAGE 11,12
    Click the FOOT MASSAGE button, foot massage motor switches massage intensity, massage
    intensity switches among 0-1-2-3
16. MASSAGE TIME 13
    Click the MASSAGE TIME button to set the massage time among 0-10-20-30mins.
17. FLAT 19
    Click the FLAT button, the bed goes flat.
18. FLASHLIGHT 8
    Click the FLASHLIGHT button to open and shut the Flashlight.

FCC warning

Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two
conditions

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause
   undesired operation.
   This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Federal Communications Commission (FCC) rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
   This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
   However, there is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by doing one or more of the following measures:
   • Reorient or relocate the receiving antenna.
   • lncrease the separation between the equipment and receiver.
   • Connect the equipment into an outlet on a circuit different from that to which the receiver is
     connected.
   • Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
The antenna(s) used for this transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC exposure compliance requirements, please follow operation instructions as documented in this manual.

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. End-users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with ISED exposure compliance requirements, please follow operation instructions as documented in this manual.

ISED RSS Warning:
This device complies with Innovation, Science and Economic Development Canada license-exempt
RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.