NOT A TOY: Children under 14 years old should use this product under adult supervision.

NOT A MEDICAL USE: This product is not a medical device, and is not intended to diagnose, treat, cure, or prevent any disease. The accuracy of our devices is not intended to match medical devices or scientific measurement devices, but is intended to give you the best infonnation available in a wearable activity tracker.

USB Charging

Please charge your new device for at least 10 minutes to have it activated before initial use.

In case that device is under low battery, connect the device host to an adapter for charging. Device will automatically boot up once fully charged. Remove the device host from the power supply once fully charged.

USB charger requirement: DC USB port (5V-500mA)

Install and Wear Your Device

Install: Plug the host into the slots of each strap.

Wear: Wear the device on your wrist horizontally, about 2cm to carpal, the same way as wearing a watch.

Smart Phone System Requirement

• iOS 7.1 & above
• Android 4.4 & above
• Bluetooth 4.0 & above

Download the APP

Download “VeryFitPro” APP for Android and iOS devices.

Option 1: Search for “VeryFitPro” in APP store or Google Play and download to your smartphone.

Notes:

• This fitness tracker requires iOS 7.1 & above or Android 4.4 & above system.
• “VeryFitPro” APP is only compatible with smartphones.

Option 2: Searching the QR code, scan and download APP. Use the QR code Scan tool to scan the following QR code, open the link and follow the instructions to download APP.

Tip: In case of problems when opening the link, copy the link and open it in a browser.

Pair the Device

1. Enable Bluetooth before binding the device.
2. Open ”VeryFitPro” APP on your smartphone and tap on “Device”-“Bind device”, then your smartphone starts searching devices.
3. Select “ID115Plus Color HR” in the list of found devices, tap on “ID115Plus Color HR” to connect the device to your smartphone.

(If failed searching the device, please tap on the touch key to wake the device (screen lights on), then start searching with your smartphone one more time.)

Notes:

• After first successful searching and binding, if you enable the Bluetooth function of the smartphone afterwards, the device will automatically search and link back to the smartphone it has bound.
• If the device is unbound under Bluetooth connected state, the APP will set the settings back to default. Al I data on the device will be cleared. If the device is unbound under Bluetooth disconnected state, the APP will set the settings back to default, but the data on the device will not be cleared.
• The device can only link to one smartphone at a time. During connecting please confirm there is no other smartphones nearby.

Touch Key

Waking a Dimmed Screen

When you’re not using ID115Plus Color HR, the display is off.

To wake it up:

• Turn your wrist towards you, the screen will display time and weather (weather forecast can be turned off in “Device”‘→”More → “Weather forecast” in the APP.)

Note:
The screen brightness can be adjusted from Level 1 to Level 5 in “Device”→”More”→”Bracelet brightness” in the APP and Level 5 is the brightest. Remember to click ” √ ” to save your settings.

• Tap on the touch key, and the device will display the main screen.

Main Functions

1.  “Alarm Mode” is displayed on the device screen only when “Alarm Alert” is ON in the APP.
2.  “Walk Mode”, ‘Run Mode” and “Bike Mode” are displayed on the device screen by default. You can set up to 3 different sports modes from 14 sports modes to display on the device screen (Go to “VeryFitPro” APP “→”Device”→”More’-> ‘Activity display”).

Function Introduction

1. Step Mode

• Long press the touch key for 2s to view detailed step data.
• Single tap on the touch key to flip through detailed step data.
• Single tap on the touch key to go to the next mode: Heart Rate Mode.

Note:
You can go to the APP to set you sports target (“User”→”Target Setting”). When you reach your sport target, the device vibrates and the screen displays:

Tap on the touch key to go back to the main screen.

2. Heart Rate Mode
After entering the heart rate interface for 1 s, the device will start monitoring the heart rate automatically. Before the correct data is detected, the device shows ” ” ; after the correct data is detected, it shows specific data.

Single tap on the touch key to go to the next mode: Alarm Mode.

3. Alarm Mode

• Long press the touch key for 2s to tum on/ off the alarm function.

Notes:

• Alarm Mode is available only when alarm(s) isfare added and enabled (turn on the switch to enable the alarm) in “Alarm alert” in the APP.
• Tap on the alarm, you can add and set the alarm types, repeat type and time. (When alarm(s) is fare added and enabled, please click” √ ” to save your settings.)

• Single tap on the touch key to go to the next mode: Walk Mode.

4. Walk Mode

• Long press the touch key for 2s to start the walk mode.

During exercise, tap on the touch key to flip through the exercise data.

• Long press the touch key for 2s to quit the walk mode.
  The following data is displayed after the exercise is ended:

Single tap on the touch key to flip through the exercise data.

• Single tap on the touch key to go to the next mode: Run Mode

Note:
Data of exercises less than 1 minute will not be saved.

5. Run Mode

• Long press the touch key for 2s to start the run mode.

During exercise, tap on the touch key to flip through the exercise data.

• Long press the touch key for 2s to quit the run mode.
  The following data is displayed after the exercise is ended:

Single tap on the touch key to flip through the exercise data.

• Single tap on the touch key to go to the next mode: Bike Mode.

6. Bike Mode

• Long press the touch key for 2s to start the bike mode.

During exercise, tap on the touch key to fl ip through the exercise data.

• Long press the touch key for 2s to quit the bike mode.
  The following data is displayed after the exercise is ended:

Single tap on the touch key to flip through the exercise data.

• Single tap on the touch key to go to the main screen.

Note:

After starting the running mode, the APP will track and map your run distance; after the exercise, you can effortless ly check your workout data.

6.1 Abnormal Situations During Exercise

1. Inactive Exit Prompt

• Device will automatically exit the sport mode if no action is taken in 15 minutes.
• Device will be forced to exit the sport mode if you don’t tap on the waiting prompt within 15 seconds.

Single tap on the touch key to cancel the Automatic Exit Sport mode prompt, then the sport mode can work as normal.

2. The prompt of being forced to exit the sport mode when memory is full

Single tap on the touch key to confirm the prompt if the devi ce is force to exit the sport mode when memory is full, then exit the sport mode and exercise data is displayed.

Notes:

• The sport mode lasts for up to 6 hours.
• When the memory is full, it will prompt that the sport mode is forced to e xit.

3. The prompt being forced to exit sport mode when battery is low
Single tap on the touch key to confirm the prompt if the device is force to exit sport mode when battery is low , then exit the sport mode and exercise data is displayed.

6.2 Abnormal Operation Situation During Exercise

When the APP and the device are disconnected, the screen will appear a prompt o f waiting: Single tap on the touch key to exit the interface of waiting prompt.

7. Other Functions

1. Call Alert

When there is an incoming call, the device displays:

Notes:

• Long press the touch key to reject the call; single tap on the touch key to return to the main screen.
• Only when “Call Alert” is ON in the APP, calls will be notified. (When turning on/off the Call Alert function, please click “√ ” to save your settings.)

2) SNS Alert
When SNS messages (including: SMS, Facebook, WhatsApp, Twitter, lnstagram, Facebook Messenger, Linkedln, Email, Mail, and Calendar) come in, the devi ce displays the message content:

Notes:

• Only when “SNS Alert” (tap on “Device” → ‘SNS Alert”→”A llow notification”) is ON in the APP, SNS messages will be notified. (When turning on/off the Call Alert function, please click “√ ” to save your settings.)
• When “Do not disturb” function is enabled in the APP (“Device” → “More” →”Do not disturb” ), messages will not be notified on the device during the set do-not-disturb period.

3. Take Photos
Open the “VeryFitPro” APP, and tap on “Device”→ “Camera”, then the device screen shows the camera interface. Single tap on the touch key of the device to control the camera of your smart phone to shoot photos.

4. Sedentary Alert

Open the “VeryFitPro” APP. Tap o n “Device” → “Sedentary Alert” to switch on the Sedentary A lert function and set the alert time. The device will vibrate and display the following interface to remind you to move after the set sedentary alert period passed.

5. Device Error Notification
Note:
When the device has an exception, the interface is displayed every time when the device is turned on.

Status code:

• 01 indicates acceleration sensor abnormality;
• 02 indicates the heart rate sensor is abnormal;
• 03 indicates touch ic is abnormal;
• 04 indicates the flash is abnormal.

Basic Specifications

• Model No.: ID115Plus Color HR
• Battery Capacity: 65mAh
• Working Voltage: 3. 7V
• Host weight: about 24 .8g
• Sync: Bluetooth 4.0
• Working Temperature: -20 C – 40 C
• Waterproof Rating: I P68-01
• Working Time: 5 days (with Automatic HR Monitoring ON), 8 days (with Automatic HR Monitoring OFF).

Electronic Information Products
Poisonous and Harmful Statement

This product meets the EU ROHS standards

Refer to IEC 62321 and EU RoHS
Directive 2011/65 / EU and its revision instructions

FAQs

Failed to bind the device with APP

1. Make sure the Bluetooth of your smartphone is ON. (Do not pair the tracker with your phone’s Bluetooth on your phone, but in “VeryFitPro” APP (Step 5). If you have already paired the tracker with your phone’s Bluetooth, click to forget the device and bind the tracker to your phone in “VeryFitPro” APP).
2. Make sure the distance between your smartphone and the device i s within O .5 meter.
3. Make sure the “VeryFitPro” APP is trusted by your smartphone by going to your smartphone system Settings, finding “VeryFitPro” APP and enabling the Location and all Notifications. (Specific setting methods may vary according to different smartphones.
4. Make sure the fitness tracker is under unbind status before pairing.
5. Open “VeryFitPro” APP on your smartphone and tap on ‘Device” → “Bind device”, then your smartphone starts searching devices. Select “ID115Plus Color HR’ in the list of found devices, and tap on “ID115Plus Color HR” to connect the device to your smartphone.
6. If you failed search the device, reboot your smartphone and Bluetooth to search it again.

Note:
For iOS smartphones, if you failed to find “ID115Plus Color HR” in the APP, take the following steps:

1. Go to your smartphone “Settings”→ “Bluetooth”. Under “MY DEVICES”, find “ID115Plus Color HR”. tap on ” ” “Forget This Device” and tum off Bluetooth.
2. Reboot smartphone and open the “VeryFitPro” APP. When asked whether to turn on the Blue tooth switch, click OK to search and bind your device.

Failed to charge the device
Make sure the direction of the device’s USB plug is correct when plugging into the USB port for charging. For correct charging. the device’s red indicator turns on and will be off when the device has been fully charged. Please remove the device host from the power supply once fully charged. Pro longed charging may shorten the battery’s life.

Failed to receive SMS/Ca/fs notifications
Calls/SMS notification function works when the deviceconnects to your smartphone via APP. Please kindly refer to the following tips:

1. Go to your smartphone system Settings, find “VeryFitPro” APP and enabl e the Locatio n and all Notificati ons. (Specific setting methods may vary according to different smartphones.
2. Turn Bluetooth on and go to the “VeryFitPro” APP to bind the device.
3. Switch “Call/SNS Alert” function on, and click”√” to save your settings.

Failed to count steps accurately
Regarding the step counting, this fitness tracker has a built-in 3D sensor. It registers your steps when you swing your arm. Sometimes the data on device may displayed a little delayed. And it will reset itself if you walk continuously less than 40 steps. To test the accuracy of the pedometer, please walk casually and continuously up to 100 steps or more.

Failed to measure heart rate
Make sure the wrist band sit neatly on your wrist before use. Tap on the touch key to go to the heart rate mode and wait for 10-20s to detect the heart rate.

Failed to connect to the smartphone
The device will disconnect from your smartphone in the following cases:

1. Smartphone Bluetooth was off or exceed normal Bluetooth connection distance range (The normal Bluetooth connection distance is within 1O meters. it can easily be reduced by walls or furniture, etc.
2. The “VeryFitPro” APP was ended in phone background process.

To reconnect the device to your smartphone, please kindly refer to the following tips:

1. Go to your smartphone system Settings, find “VeryFitPro” APP and enable the Location and all Notifications. (Spec ific setting methods may vary according to different smartphones.
2. Clear all running/background processes in your smartphone, go to “VeryFilPro” APP, and swipe down Mainpage, then the device will reconnect to your smartphone and refresh data. You can also restart you smartphone and Bluetooth, then rebind the device on APP.

Failed to sync your tracker data to APP
To sync your tracker data to “VeryFitPro” APP, go to “VeryFitPro” APP and swipe down Mainpage under connection state.

Bind Watch

1. Download and install app
You can set up the watch through the VeryFitPro app for iOS or Android devices. The steps are shown as follows.

Notes: The hardware platform of the equipment system shall meet requirements.

iOS 8.0 version or above	Android 4.4 system or above	Support Bluetooth 4.2

Correct operation: Scan the QR code below or on the watch or download “VeryFitPro”App through the mobile App Store to pair with the watch

Wrong operation: Pair the watch directly with the Bluetooth in your mobile phone’s settings.

2. Bind process

1. Turn on the Buetocth and GPS on your mcbile phone. Find the binding request on the pull-down list on the home page of the APP.
2. Select product Model：ID205G
3. Click“Ok”to Complete binding

Notes:
* During binding process, VeryFitPro will prompt you to enable GPS and Bluetooth, and authorize VeryFitPro to get access to the GPS on you mobile phone.
* iPhones will not prompt you with any information unless you complete Bluetooth pairing on your ID205G watch in the built-in Bluetooth in you mobile phone after binding.

Synchronous Data

In daily wear, the watch can detect all kinds of exercise data. The user needs to connect the watch with bluetooth on the APP before synchronous operation. The detailed operations are shown as follows:

Open the mobile APP
>swipe down the page
> sync prompt appears

Notes!
* Please synchronize the data at least once within 7 days to avoid data loss at the watch end.
* The Apple phone also needs to be connected to the paired watch in the bluetooth setting interface of the mobile phone, so that the watch can be alerted. The steps are shown as follows:

Open the IOS phone >set>bluetooth>search and click pair

Instructions for use

1.Charging schematic
Connect and charge the watch according to the picture. It needs to be charged to activate the watch when it is started for the first time.2.Wear/install

Wear the device a finger’s distance from the wrist bone and adjust the tightness of the wristband to a comfortable position.	Flip the switch and take out the wristband

Tip: Wearing too loosely may affect the accuracy of heart rate data.

Operating Instructions

1.Definition of Key function

Short press the right key: Return to previous interfaceLong press the right key: start

2. Watch dial switch

Replacing the dial interface will appear after long pressing the dial.

3. Main interface operation
Swipe the screen to enter different interfaces (interactive interface tile diagram)

Function Introduction

1.Icon function introduction

1. Enter the sports window, and choose different sports Modes. Change the sports mode on the APP.
2. Perform a heart rate test to check your heart rate data for the day.
3. Help you regulate your breathing and relax your mood.
4. View, turn off or turn on the alarm clock. You need to add an alarm clock On the mobile App.
5. Control music play on your mobile phone (watch cannot store music).
6. Have the timing and countdown function.
7. Record recent sports.

Notes: For more functions (sleeping) and operation, please check the VeryFitPro software of the mobile phone.

2.Start sports

1. Enter sports
   Click the sports icon > select the sports type > enter the sports countdown automatically.
2. During sports
   Pause sports: short press the right key.
   Restore sports: short press the right key.
3. End sports
   End sports: long press the right key > select the end button on the screen.

3.women’s health tracking

Display location in the data bar

Women’s health tracking function, which is used for recording menstrual changes, tracks individual menstrual cycle and predicts ovulation (it needs to be enabled on the APP).

Product Parameters

Range of charging temperature: 10°C – 45°C
Battery life: Actual battery life and charging time will vary depending on usage and environment, etc.
Waterproof: Not suitable for diving, swimming in the sea or sauna, but suitable for swimming in the swimming pool or in the shower (cold watr) and shallow beach.

Cleaning and Maintenance

lt is recommended to wear and maintain according to the following three points:

1. Keep the product clean.
2. Keep the product dry.
3. Do not wear it too tight.

* Do not use household cleaners to clean the watch, but use the soap free detergent.
* It is recommended to use alcohol to scrub stains that are not easy to remove.

FAQ

Q1 . Mobile APP search for the watch failed
1) It is recommended to update VeryFitPro to the latest version.
2) It is recommended to close all programs, restart the Bluetooth, and then connect.
3) Confirm whether the mobile phone system meets Android 4.4 or IOS 8.0 or above.

Q2 . The watch received no alerts, text messages or phone calls
1) You need to turn on the smart reminder function and the call reminder switch in the APP, and synchronize to the watch.
2) The iphone needs to be paired with the watch via Bluetooth. (Please check the column of “Synchronous Data” for details)
3) You need to keep your watch connected to Bluetooth.

Q3 . Bluetooth is often disconnected
1) If the distance between the watch and the mobile phone is too far, the connection effect of more than 7m bluetooth is obviously weakened.
2) Whether there is a shield between the watch and the mobile phone, the human body, wearing metal jewelry, etc. will interfere with the bluetooth connection signal.
3) Whether the bluetooth function of the mobile phone is abnormal.

Q4 . About data backup
The data of the watch is synchronized at least once every 7 days to the mobile phone (the watch end only keeps the data of the last 7 days).

Q5 . How to restart and restore factory settings
Shutdown operation: Watch > set > shutdown/right key restart. Restore factory settings:connect watch to APP>open APP > device model > more settings.

Q6 . Do I need to keep my bluetooth on when I wear my watch?
1) For the three functions, i.e. counting steps, sleeping and alarm clock, you do not need to connect the watch to the mobile phone all the time. If you only need to wear a watch when you exercise, you can connect the watch and your mobile phone to view the data synchronously after the exercise.
2) For the functions of call alert message alert, find the phone, you need to turn on the mobile phone’s bluetooth, and maintain the connection with the mobile phone.

Safety and Product Information

Notes

Battery warning
Do not disassemble, bore or damage the battery. Do not disassemble the built-in batteries of nonreplaceable battery devices. Do not use sharp objects to remove the battery.

Health Warning
If you are wearing a pacemaker or other implanted electronic devices, please consult your doctor before using the heart rate monitoring strap.
The watch’s optical heart rate sensor glows green and flashes. If you suffer from epilepsy or are sensitive to blinking light sources, please consult your physician if you can wear this product.
The device tracks your daily activities through sensors. These data are intended to tell you about your daily activities, such as steps, sleep, distance, heart rate and calories, but may not be completely accurate.
The device, accessories, heart rate sensors and other relevant data are designed for entertainment and fitness, not for medical purposes. They are not applicable to the diagnosis, monitoring, treatment or prevention of any diseases or symptoms. The heart rate data is for reference only. We are not responsible for any consequences caused by any data deviation.

Cycling Warning
If you are wearing a pacemaker or other implanted electronic devices, please consult your doctor before using the heart rate monitoring strap.

Notes:
Device data should be synchronized once every seven days to avoid data loss.
The device has no waterproof effect on seawater, acidic and alkaline solution, chemical reagent and other corrosive liquids.

The damage or defect caused by misuse or improper use is beyond the warranty scope. The device supports the use under cold shower or swimming excluding diving.

* In daily use, the device should be avoided from wearing too tight. Please keep the parts where the device touches the skin dry.
* During heart rate detection, please keep your arm stand still.

The device meets the EU ROHS criterion.
Please refer to IEC 62321, EU ROHS
Directive 2011/65/EU and revised directive.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN NCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.