Safety Warnings

• Before use, please read the user manual and safety warnings carefully , and make sure you understand and accept all the safety instructions . The user will be responsible for any loss or damage caused by improper use.
• Before each cycle of operation , the operator shall perform the preparation checks specified by the manufacturer : That all guards and pads originally supplied by the manufacturer are in proper place and in serviceable condition ; That the braking system is functioning properly; That any and all axle guards, chain guards, or other covers or guards supplied by the manufacturer are in place and in serviceable concertation; That tires are in good condition, inflated properly, and have sufficient tread remaining; The area that the product is to be operated should be safe and suitable for safe operation.
• components shall be maintained and repaired in accordance with the manufacturer’s specifications and using only the manufacturer’s authorized replacement parts with installation performed by dealers or other skilled persons.
• Don’t allow hands, feet , hair, body parts , clothing, or similar articles to come in contact with moving parts, wheels, or drive train , while the motor is running.
• This product should not be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they hove been given supervision or instruction (IEC 60335-1/A2:2006).
• unsupervised children should not play with the product (IEC 60335-1/A2:2006).
• Adult supervision is required.
• The rider should not exceed 265 lb.
• Never use near motor vehicle.
• Units shall not be operated to perform racing, stunt riding, or other maneuvers, which may cause loss of control, or may cause uncontrolled operator/passenger actions or reactions.
• Avoid sharp bun1)S, drainage grates, and sudden surface changes. Scooter may suddenly stop.
• Avoid streets and surfaces with water, sand, gravel, dirt, leaves, and other debris . Wet weather impairs traction, braking, and visibility.
• Avoid riding around flammable gas , steam, liquid, or dust that could cause fire .
• Operators shall adhere to all of the manufacturer’s recommendations and instructions, as well as comply with all laws and ordinances: Units without headlights shall be operated only with adequate daylight conditions of visibility , and ; Owners shall be encouraged to highlight (for conspicuity) using lighting, reflectors , and for low-riding units , signal flags on flexible poles .
• Do not ride at night.
• Only ride the product with adequate daylight conditions for visibility.
• Persons with the following conditions shall be cautioned not to operate : Those with heart conditions; Pregnant women ; Persons with head , back, or neck ailments, or prior surgeries to those areas of the body ; and persons with any mental or physical conditions that may make them susceptible to injury or impair their physical dexterity or mental capabilities to recognize, understand, and perform all of the safety instructions and to be able to assume the hazards inherent in unit use .
• Do not ride after drinking or taking prescription medication.
• Do not carry items when riding.
• Never operate the product barefooted.
• Always wear shoes and keep shoelaces tied .
• Make sure your feet are always placed securely on the deck .
• Operators always shall use appropriate protective clothing, including but not limited to a helmet, with appropriate certification, and any other equipment recommended by the manufacturer : Always wear protective equipment such as helmet , knee pads , and elbow pads.
• Always give way to pedestrians.
• Be alert to things in front and far away from you.
• Do not allow distractions when riding, such as answering the phone or engaging in any other activities.
• The product cannot be ridden by more than one person.
• When you ride the product along with other riders, always keep a safe distance to avoid a collision.
• When turning, be sure to maintain your balance.
• Riding with improperly adjusted brakes is dangerous and can result in serious injury or death.
• Applying brakes too hard or too suddenly can lock up a wheel, which could cause you to lose control and fall. Sudden or excessive application of the brake may result in injury or death .
• The brake may became hot while operating, do not touch the brake with your bare skin.
• If the brake loosens, please adjust with the hexagon wrench, or please contact Jetson Customer Support.
• Replace worn or broken parts immediately.
• The area that the product is to be operated should be safe and suitable for safe operation.
• Check whether all safety labels are in place and understood before riding.
• The owner shall allow the use and operation of the unit after a demonstration that such operators can understand and operate all components of the unit before use.
• Recommended for indoor use.
• Use caution when charging. Do not operate charger near flammable materials. Unplug charger and disconnect from scooter when not in use.
• When the battery is fully charged, stop charging and unplug the unit.
• Prolonged exposure to UV rays, rain and the elements may damage the enclosure materials, store indoors when not in use.

California Proposition 65
WARNING

This product can expose you to a chemical such as Cadmium that is known to the state of California to cause cancer or bi rth defects or other reproductive harm. For more information go to www.p65warnings.ca. gov/product

NOTICE OF COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference , and (2) this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment hos been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which con be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• connect the equipment into on outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or on experienced radio/ TV technician for help.

Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.

MODIFICATIONS

Do not attempt to disassemble , modify, repair , or replace the product or any components of the unit without instruction from Jetson Customer Support . This will void any warranty, and can lead to malfunctions which may cause injury.

ADDITIONAL OPERATION CAUTIONS

Do not lift the product off the ground while it is on and the wheels are in motion . This can result in freely spinning wheels, which may cause injury to yourself or others nearby . Do not jump on or off the product, and do not jump while using it . Always keep your feet firmly planted on the mat sensors while in operation . Always check the battery charge before using.

MAINTENANCE CAUTIONS

For all maintenance repairs and needs beyond the capability of the consumer which may include but not limited to such as proper maintenance of brakes , control cables, bearing adjustments, wheel adjustments, lubrication, reflectors, tires and handlebar and seat adjustments, please contact Jetson Customer Support for assistance at:

support . ridejetson.com
us & Canada 1-(888) 976-9904
UK +44 (0)33 0838 2551
Spain/Portugal +34 952 179 479
Hours of Operation: 7 days a week 10am-6pm EST

DISPOSAL OF USED BATTERY

Battery may contain hazardous substances which could endanger the environment and human health . This symbol marked on the battery and/or packaging indicates that used battery shall not be treated as municipal waste . Batteries should be disposed of at an appropriate collection point for recycling. By ensuring the used batteries are disposed of correctly , you will help preventing potential negative consequences for the environment and human health . The recycling of materials will help to conserve natural resources . For more information about recycling of used batteries, please contact your local municipality waste disposal service

Remember to be safe and most importantly, have fun!

• Adults must assist children in the initial adjustment procedures of the product .

What’s in the Box

1. Front Tire
2. Headlight
3. Stem Quick Release
4. Front Reflector
5. Handlebar
6. carrying Handle
7. Seat
8. Rear Reflector
9. Seat Clomp
10. Fog Light
11. Rear Fender
12. Rear Tire
13. Kickstand
14 . Pedal
15 . Front Fender
16. Charging Coble
17. Charger

Tools needed but not included: Screw Driver, Ratchet + Socket
CAUTION : Before operating the Bolt Pro please tighten all screws, nuts , and bolts .

Specs & Features

• Folded Dimensions: 46. 5″ x 19.3″ x 23″
• Unfolded Dimensions: 46.5″ x 19 .3″ x 38. 6″
• Weight Limit: 265 lb
• Product Weight: 41 lb
• Recommended Age : 12+
• Tire Size: 14 in
• Speed: Up to 15 .5 mph
• Pedal Assist Range: Up to 30 miles
• Twist Throttle Range: Up to 15 miles
• Battery: 36V, 6. 0Ah Lithium-Ion
• Motor : 350W Hub Motor
• Charge Time: Up To 4 Hours
• Climbing Angle: Up To 15°

Correct Frame Size

For safe and comfortable riding there should be a clearance of 22 inches from ground to the crotch of the intended rider . Also, at least 1-3 inches between the crotch and the top tube of the bicycle frame, while the rider straddles the bicycle with both feed flat on the ground. Women can use a men’s style bicycle to determine the correct size women’s model.

Get Started

Attaching the seat

Insert Seat Post in to Seat Tube. Slide Seat into Stem Tube.

Turn the Knob clockwise to tighten Seat Clamp . Close the Seat Clamp

Attaching the Pedals

Find Pedal Markings L & R. Hand tighten the pedals to the crank arms, then securely tighten with a 15mm Wrench.
* Note: the Left Pedal is reverse threaded , turn Counter Clockwise to tighten.

Attaching the Fender

Remove Bolt and Nut from the frame . Run the Bolt through the Fender and frame , and secure using the Nut.

Stay Charged

Make Moves

Unfolding the Handlebar

Operating the Bolt Pro

Power Button: Turns the Bolt Pro on and off .

Cruise Control/ Head Light Button:
• Press once to activate Cruise Control
• Hold button for 4 seconds to turn light on/off

Battery Levels:
4 Lights: 76-100% Power
3 Lights: 51-75% Power
2 Lights: 26-50% Power
1 Light: 1-25% Power (Please charge the Bolt Pro immediately!)

Care & Maintenance

Riding Range
The maximum range is 15 miles using the Twist Throttle and 30 miles using Pedal Assist. However, o lot of factors will affect how for you con go per charge:

• Riding Surface: A smooth, flat surface will increase riding distance .
• Weight: More weight means less distance.
• Temperature: Ride and store the Bolt Pro above 10°c I 50°F.
• Maintenance: Timely battery charging will increase riding distance.
• Speed and Riding Style: Frequent starting and stopping will reduce riding distance.

Cleaning The Bolt Pro
To clean the Bolt Pro, carefully wipe with o damp cloth , then dry with o dry cloth. Do not use water to clean the Bolt Pro, as the electrical and electronic systems may get wet, resulting in personal injury or malfunction of the Bolt Pro.

Battery
• Keep the Bolt Pro away from fire and excessive heat.
• Do not subject the Bolt Pro to intense physical shock, severe vibration, or impact.
• Protect from water or moisture.
• Do not disassemble the Bolt Pro or its battery .
• If there ore any issues with the battery, please contact Jetson Customer Support. We ‘d love to help!

Storage
• Fully charge the battery before storing.
• The battery should be fully charged once o month after this.
• To protect against dust, cover the Bolt Pro.
• Store the Bolt Pro indoors, in o dry place and at o suitable temperature .
• You should bring the Bolt Pro into o worm (above 10°c / 50°F} environment for charging.

Enjoying your product?

Leave a review an ridejetsan.com or share your photos with us online using the #RideJetson hashtag!

Safety Warnings

• Before use, please read the user manual and safety warnings carefully, and make sure you understand and accept all the safety nstructions. Ihe user will be responsible for any loss or damage caused by improper use. .
• Before each cycle of operation, the operator shall pertorm the preoperation checks specified by the manutacturer: That all guards and
• pads originally supplied by the manufacturer are in proper place and in serviceable condition; That the braking system is functioning properly: That any and all axle guards, chain guards, or other covers or guards supplied by the manutacturer are in place and in serviceablee condition;That tires are in good condition, intlated properly, and have sufficient tread remaining; The area that the product is to be Components shall be maintained and repaired in accordance with the manufacturer’s specifications and using only the manufacturer’s authorized replacement parts with installation
• pertormed by dealers or other skilled persons.
• Warning against recharging non-rechargeable batteries.
• Don’t allow hands, feet, hair, body parts, clothing, or similar articles to come in contact with moving parts, wheels, or drive train, while the motor is running.
• This product should not be used by children or persons with reduced physical, sensoryor mental capabilities, or lack of experience and knowledge, unless they have been gIven supervision or instruction (IEC 60335-1/A2:2006).
• Unsupervised children should not play with the product (IEC 60335-1/A2:2006).
• The rider should not exceed 220 Ib.
• Units shall not be operated to perform racing, stunt riding, or other maneuvers, which may cause loss of control, or may causse ncontrolled operator/passenger actions or reactions.
• Never use near notor venicles.
• Avoid sharp bumps, drainage grates, and sudden surtace changes. Scooter may suddenly stop.
• AVOId streets and surtaces with water, sand, gravel, dirt, leaves, and other debris. wet weather impairs traction, braking, and viISIbility.
• Avoid riding around flammable gas, steam, liquid, or dust that could cause fire.
• Operators shall adhere to al! of the manufacturers recommendations and instructions. as well as comply with all laws and ordinances:
• Oeacgna Deere any ideal agent cantons Dana wners shal De encouraged to nignignt Persons with the following conditions shall be cautioned not to operate: Those with heart conditions: Pregnant women: Persons with head, back, or neck ailments, or prior surgeries to those areas of the body; and persons with any mental or physical conditions that may make them susceptible to injury or impair their physical dexterity or mental capabilities to recognize, understand, and perform all of the satety nstructions and to be able to assume the hazards inherent in unit use.
• Do not ride at night.
• Do not ride after drinking or taking prescription medication.
• Do not carry items when riding
• Never operate the product barefooted.
• Always wear sth r alwavs placed securely on the deck.
• tied
• Operators always shall use appropriate protective clothing, including but not limited to a helmet, with appropriate certification, and any other equipment recommended by the manufacturer: Always wear protective equipment such as helmet, knee pads, and elbow pads.
• AIways give way to pedestrians.
• alert to things in front and tar away from you.
• Do not allow distractions when riding, such as answering the phone or engaging in any other activities.
• The product cannot be ridden by more than one person.
• When you ride the product along with other riders, always keep a safe distance to avoida collision.
• generous and can result in serious injury or death.
• The brake may become hot while operating, do not touch the brake with your bare skin.
• Applying brakes too hard or too suddenly can lock up a wheel, which could cause you to lose control and fall. Sudden or excessiIve application of the brake may resuit in injury or death.
• the brake loosens, please adjust with the hexagon wrench, or please contact Jetson Customer Care.
• Replace worn or broken parts immediately.
• The cha yDes are in place and understood before riding.
• components of the unit before use. a d ueo1straion tnat such operators can understand and operate al Do not ride without proper training. Do not ride at high speeds, on uneven terrain, or on slopes. Do not perform stunts or turn abruptly.
• Recommended or indoouse.
• Prolonged exposure to UV rays, rain and the elements may damage the enclosure materials, store indoors when not in use.

California Proposition 

WARNING
This product can expose you to a chemical such as Cadmium that is known to the state of Calitornia to cause cancer or birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov/product

MODIFICATIONS
Do not attempt to disassemble, modity, repair, or replace the unit or any components of the unit without instruction from Jetson Customer Care. This will void any warranty, and can lead to malfunctions which may cause injury.

ADDITIONAL OPERATION CAUTIONS
Do not lift the product off the ground while it is on and the wheels are in motion. This can result in freely spinning wheels, which may cause injury to yourselt or others nearby. Do not jump on or off the product, and do not jump while using it. Always keep your feet firmly planted on the foot rest while in operation. Always check the battery charge before using.

NOTICE OF COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: this device may not cause harmful interference, and (2) this cdevice must accept any interference received, including interference that may cause undesired operation. warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and tound to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Ihese limits are designed to provide reasonable protection against harmful interference in a residential installation. Ihis equipment fre Darmful interference to radio communicationsHoweyer there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: eorlent or relocate tne receiving antenna. Increase the separation between the equipment and receiver. Connecting equipment into an outet on a circuit different torment to which the receiver is Connected. Consult the dealer or an experienced radio/ TV technician for help
Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.

DISPOSAL OF USED BATTERY
The battery may contain hazardous substances which could endanger the environment and human health. This symbol marked on the battery and/ or packaging indicates that used battery shall not be treated as municipal waste. Batteries should be disposed of at an appropriate collection point for recycling. By ensuring the used batteries are disposed of correctly, you will help preventing potential negative consequences for the environment and human health. The recycling of materials will help to conserve natural resources. For more information about recycling of used batteries, please contact your local municipality’s waste disposal service.

Sync Overview

1. LED LIGHTS
2. POWER BUTTON
3. CHARGING PORT
4. CHARGER

ADULTS MUST ASSIST CHILDREN IN THE INITIAL ADJUSTMENT PROCEDURES OF THE PRODUCT.

PLEASE NOTE: IMAGES MAY NOT REFLECT EXACT APPEARANCE OF ACTUAL PRODUCT.

Specs & Features

• WEIGHT LIMIT: 220 LB
• PRODUCT WEIGHT: 16 LB
• TIRE SIZE: 6.3″
• PRODUCT DIMENSIONS: L24.2″ x W7″ x H7.4″
• MAX SPEED: UP TO 10 MPH
• MAX RANGE: UP TO 8 MILES
• BATTERY: 36V, 2.0AH LITHIUM-ION
• MOTOR: 300W
• CHARGER: UL LISTED, 100-240V
• CHARGE TIME: UP TO 4 HOURS
• CLIMBING ANGLE: UP TO 15°
• RECOMMENDED AGE: 12+

Get Started Charging the Battery

• ONLY USE THE INCLUDED CHARGER
• PLUG THE CHARGER INTO THE WALL BEFORE THE CHARGING PORT
• DON’T TURN ON THE SYNC WHILE IT’S CHARGING
• CHARGE THE BATTERY UNTIL IT IS FULLY CHARGED • UP TO 4 HOURS
• CHARGING
• CHARGE COMPLETE

Indicator Lights

WARNING: THE SYNC WILL AUTOMATICALLY TILT UP AND SLOW DOWN ONCE THE BATTERY POWER GOES BELOW 10% AS A SAFETY PRECAUTION.

How to Recalibrate

FOLLOW THESE 3 SIMPLE STEPS:

1. PLACE TURNED OFF SYNC ON AFLAT SURFACE. HOLD THE POWER BUTTON FOR 5 SECONDS UNTIL THE TUNE IS COMPLETE. THE SYNC IS NOW ON.
2. LET GO OF POWER BUTTON AND THEN HOLD FOR 2 SECONDS TO TURN SYNC OFF.
3. TURN SYNC BACK ON; RECALIBRATION IS NOW COMPLETE.
   KEEP THE HOVERBOARD LEVELED AND STILL THROUGHOUTTHE RECALIBRATION PROCESS.

Make Moves

Riding the Hoverboard

Helmet Safety

Connecting to Bluetooth
THE HOVERBOARD COMES EQUIPPED WITH A BLUETOOTH® SPEAKER.
TO CONNECT TO YOUR BLUETOOTH° SPEAKER:
TURN ON THE SYNC AND IT WILL BECOME DIscoVERABLE TO YOUR HANDHELD DEVICE
ACTIVATE YOUR BLUETOOTH° IN YOUR HANDHELD DEVICE’S SETTINGS.
FIND THE SYNC IN YOUR HANDHELD DEVICE’S LIST AND SELECT IT.
NOW YOU CAN PLAY YOUR MUSIC.

Care &Maintenance

SPEED AND RIDING RANGE
THE TOP SPEED IS 10 MPH, HOWEVER, MANY FACTORS WILL AFFECT HOW FAST YOU WILL BE ABLE TO RIDE:

• DRIVING SURFACE: A SMOOTH, FLAT SURFACE WILL INCREASE DRIVING DISTANCE.
• WEIGHT: MORE WEIGHT MEANS LESS DISTANCE.
• TEMPERATURE: RIDE, CHARGE, AND STORE THE SYNC ABOVE 50°F.
• MAINTENANCE: TIMELY BATTERY CHARGING WILL INCREASE DRIVING DISTANCE.
• SPEED AND DRIVING STYLE: FREQUENT STARTING AND STOPPING wILL REDUCE DRIVING DISTANCE.

CLEANING THE SYNC
TO CLEAN THE SYNC, CAREFULLY WIPE WITH A DAMP CLOTH, THEN DRY WITH A DRY CLOTH. DO NOT USE WATER To CLEAN THE SYNC, AS THE ELECTRICAL AND ELECTRONIC SYSTEMS MAY GET WET, RESULTING IN PERSONAL INJURY OR MALFUNC TION OF THE SYNC.

BATTERY
KEEP AWAY FROM FIRE AND EXCESSIVE HEAT. AVOID INTENSE PHYSICAL SHOCK, SEVERE VIBRATION, OR IMPACT. PROTECT FROM WATER OR MOISTURE.
DO NOT DISASSEMBLE THE SYNC OR ITS BATTERY. IF THERE ARE ANY ISSUES WITH THE BATTERY, PLEASE CONTACT JETSON CUSTOMER SUPPORT.

STORAGE
FULLY CHARGE THE BATTERY BEFORE STORING. THE BATTERY SHOULD BE FULLY CHARGED ONCEA MONTH AFTER THIS. COVER THE SYNC TO PROTECT AGAINST DUST. STORE THE SYNC INDOORS, IN A DRY PLACE.

FCC statement

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Safety Warnings

• Before use, please read the user manual and safety warnings carefully, and make sure you understand and accept all the safety instructions. The user will be responsible for any loss or damage caused by improper use.
• Before each cycle of operation, the operator shall perform the preoperation checks specified by the manufacturer: That all guards and pads originally supplied by the manufacturer are in the proper place and in serviceable condition; That the braking system is functioning properly; That any and all axle guards, chain guards, or other covers or guards supplied by the manufacturer are in place and in-service condition; That tires are in good condition, inflated properly, and have sufficient tread remaining; The area that the product is to be operated should be safe and suitable for safe operation.
• Components shall be maintained and repaired in accordance with the manufacturer’s specifications and using only the manufacturer’s authorized replacement parts with installation performed by dealers or other skilled persons.
• Warning against recharging non-rechargeable batteries.
• Don’t allow hands, feet, hair, body parts, clothing, or similar articles to come in contact with moving parts, wheels, or drive trains, while the motor is running.
• This product should not be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction (IEC 60335-1/A2:2006).
• Unsupervised children should not play with the product (IEC 60335-1/A2:2006).
• Adult supervision is required.
• The rider should not exceed 220 lb.
• Units shall not be operated to perform racing, stunt riding, or other maneuvers, which may cause loss of control or may cause uncontrolled operator/passenger actions or reactions.
• Never use near motor vehicles.
• Avoid sharp bumps, drainage grates, and sudden surface changes. The scooter may suddenly stop.
• Avoid streets and surfaces with water, sand, gravel, dirt, leaves, and other debris. Wet weather impairs traction, braking, and visibility.
• Avoid riding around flammable gas, steam, liquid, or dust that could cause a fire.
• Operators shall adhere to all of the manufacturer’s recommendations and instructions, as well as comply with all laws and ordinances:
  Units without headlights shall be operated only with adequate daylight conditions of visibility, and; Owners shall be encouraged to highlight (for conspicuity) using lighting, reflectors, and for low-riding units, signal flags on flexible poles.
• Persons with the following conditions shall be cautioned not to operate: Those with heart conditions; Pregnant women; Persons with head,
  back, or neck ailments, or prior surgeries to those areas of the body; and persons with any mental or physical conditions that may make them susceptible to injury or impair their physical dexterity or mental capabilities to recognize, understand, and perform all of the safety instructions and to be able to assume the hazards inherent in unit use.
• Do not ride at night.
• Do not ride after drinking or taking prescription medication.
• Do not carry items when riding.
• Never operate the product barefooted.
• Always wear shoes and keep shoelaces tied.
• Make sure your feet are always placed securely on the deck.
• Operators always shall use appropriate protective clothing, including but not limited to a helmet, with the appropriate certification, and any other equipment recommended by the manufacturer: Always wear protective equipment such as helmet, knee pads, and elbow pads.
• Always give way to pedestrians.
• Be alert to things in front and far away from you.
• Do not allow distractions when riding, such as answering the phone or engaging in any other activities.
• The product cannot be ridden by more than one person.
• When you ride the product along with other riders, always keep a safe distance to avoid a collision.
• When turning, be sure to maintain your balance.
• Riding with improperly adjusted brakes is dangerous and can result in serious injury or death.
• The brake may become hot while operating, do not touch the brake with your bare skin.
• Applying brakes too hard or too suddenly can lock up a wheel, which could cause you to lose control and fall. Sudden or excessive application of the brake may result in injury or death.
• If the brake loosens, please adjust with the hexagon wrench, or please contact Jetson Customer Care.
• Replace worn or broken parts immediately.
• Check whether all safety labels are in place and understood before riding.
• The owner shall allow the use and operation of the unit after a demonstration that such operators can understand and operate all components of the unit before use.
• Do not ride without proper training. Do not ride at high speeds, on uneven terrain, or on slopes. Do not perform stunts or turn abruptly.
• Recommended for indoor use.
• Prolonged exposure to UV rays, rain, and the elements may damage the enclosure materials, store indoors when not in use.

California Proposition 65

WARNING.
This product can expose you to a chemical such as Cadmium that is known to the state of California to cause cancer or birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov/product
MODIFICATIONS
Do not attempt to disassemble, modify, repair, or replace the unit or any components of the unit without instruction from Jetson Customer Care. This will void any warranty and can lead to malfunctions that may cause injury.
ADDITIONAL OPERATION CAUTIONS
Do not lift the product off the ground while it is on and the wheels are in motion. This can result in freely spinning wheels, which may cause injury to yourself or others nearby. Do not jump on or off the product, and do not jump while using it. Always keep your feet firmly planted on the footrest while in operation. Always check the battery charge before using.

NOTICE OF COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
  Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.

DISPOSAL OF USED BATTERY
The battery may contain hazardous substances which could endanger the environment and human health. This symbol marked on the battery and/ or packaging indicates that the used battery shall not be treated as municipal waste. Batteries should be disposed of at an appropriate collection point for recycling. By ensuring the used batteries are disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The recycling of materials will help to conserve natural resources. For more information about the recycling of used batteries, please contact your local municipality waste disposal service.

Sync Overview

1. LED LIGHTS
2. POWER BUTTON
3. CHARGING PORT
4. CHARGER

*ADULTS MUST ASSIST CHILDREN IN THE INITIAL ADJUSTMENT PROCEDURES OF THE PRODUCT.

PLEASE NOTE. IMAGES MAY NOT REFLECT THE EXACT APPEARANCE OF THE ACTUAL PRODUCT

Specs & Features

• WEIGHT LIMIT: 220 LB
• PRODUCT WEIGHT: 16 LB
• TIRE SIZE: 6.3″
• PRODUCT DIMENSIONS: L24.2″ W7″ x H7.4″
• MAX SPEED: UP TO 10 MPH
• MAX RANGE: UP TO 8 MILES
• BATTERY: 36V, 2.0AH LITHIUM-ION
• MOTOR: 300W
• CHARGER: UL LISTED, 100-240V
• CHARGE TIME: UP TO 4 HOURS
• CLIMBING ANGLE: UP TO 15°
• RECOMMENDED AGE: 12+

Get Started

Charging the Battery

• ONLY USE THE INCLUDED CHARGER
• PLUG THE CHARGER INTO THE WALL BEFORE THE CHARGING PORT
• DON’T TURN ON THE SYNC WHILE IT’S CHARGING
• CHARGE THE BATTERY UNTIL IT IS FULLY CHARGED – UP TO 4 HOURS

CHARGING
CHARGE COMPLETE

Indicator lights

BATTERY INDICATOR LIGHT
PERCENTAGE	‹20%	20-49%	50%+

STATUS LIGHT
STATUS	your synopsis is all set.	RECALIBRATE YOUR SYNC.

WARNING: THE SYNC WILL AUTOMATICALLY TILT UP AND SLOW DOWN ONCE THE BATTERY POWER GOES BELOW 10% AS A SAFETY PRECAUTION.
How to Recalibrate

FOLLOW THESE 3 SIMPLE STEPS:

1. PLACE TURNED OFF SYNC ON A FLAT SURFACE. HOLD THE POWER BUTTON FOR 5 SECONDS UNTIL THE TUNE IS THE SYNC IS NOW ON.
2. LET GO OF THE POWER BUTTON AND THEN HOLD FOR 2 SECONDS TO TURN SYNC OFF.
3. TURN SYNC BACK ON; RECALIBRATION IS NOW COMPLETE.

* KEEP THE HOVERBOARD LEVELED AND STILL THROUGHOUT THE RECALIBRATION PROCESS.

Make Moves

Riding the Hoverboard

Helmet Safety

Connecting to Bluetooth®

THE HOVERBOARD COMES EQUIPPED WITH A BLUETOOTH¹ SPEAKER.

TO CONNECT TO YOUR BLUETOOTH ° SPEAKER:

• TURN ON THE SYNC AND IT WILL BECOME DISCOVERABLE TO YOUR HANDHELD DEVICE.
• ACTIVATE YOUR BLUETOOTH’ IN YOUR HANDHELD DEVICE’S SETTINGS.
• FIND THE SYNC IN YOUR HANDHELD DEVICE’S LIST AND SELECT IT.
• NOW YOU CAN PLAY YOUR MUSIC.

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, inc. And any use of such marks by Jetson Electric Bike LLC. is under license. Other trademarks and trade names are those of their respective owners.

Care & Maintenance

SPEED AND RIDING RANGE

THE TOP SPEED IS 10 MPH, HOWEVER, MANY FACTORS WILL AFFECT HOW FAST YOU WILL BE ABLE TO RIDE:

• DRIVING SURFACE: A SMOOTH, FLAT SURFACE WILL INCREASE DRIVING DISTANCE.
• WEIGHT: MORE WEIGHT MEANS LESS DISTANCE.
• TEMPERATURE: RIDE, CHARGE, AND STORE THE SYNC ABOVE 50°F.
• MAINTENANCE: TIMELY BATTERY CHARGING WILL INCREASE DRIVING DISTANCE.
• SPEED AND DRIVING STYLE: FREQUENT STARTING AND STOPPING WILL REDUCE DRIVING DISTANCE.

CLEANING THE SYNC

TO CLEAN THE SYNC, CAREFULLY WIPE WITH A DAMP CLOTH, THEN DRY WITH A DRY CLOTH. DO NOT USE WATER TO CLEAN THE SYNC, AS THE ELECTRICAL AND ELECTRONIC SYSTEMS MAY GET WET, RESULTING IN PERSONAL INJURY OR MALFUNC­TION OF THE SYNC.

BATTERY

• KEEP AWAY FROM FIRE AND EXCESSIVE HEAT.
• AVOID INTENSE PHYSICAL SHOCK, SEVERE VIBRATION, OR IMPACT.
• PROTECT FROM WATER OR MOISTURE.
• DO NOT DISASSEMBLE THE SYNC OR ITS BATTERY.
• IF THERE ARE ANY ISSUES WITH THE BATTERY, PLEASE CONTACT JETSON CUSTOMER SUPPORT.

STORAGE

• FULLY CHARGE THE BATTERY BEFORE STORING. THE BATTERY SHOULD BE FULLY CHARGED ONCE A MONTH AFTER THIS.
• COVER THE SYNC TO PROTECT AGAINST DUST.
• STORE THE SYNC INDOORS, IN A DRY PLACE.

Enjoying the ride?
Leave a review on ridejetson.com/reviews or share your photos with us online using the #RideJetson hashtag!Follow us @ridejetson
#MakeMoves Questions? Let us know.
support.ridejetson.com
Hours of Operation:
7 Days a Week, 10 am-6 pm
Manufactured in Yueyang, China.
Imported by Jetson Electric Bikes LLC.
86 34th Street 4th Floor, Brooklyn, New York 11232
www.ridejetson.com

Made in China
Date Code: 06/2021

CONFIDENTIAL FILE INFORMATION THIS PAGE IS NOT FOR PRINT

DATE: 05/24/2021
FILENAME: Sync-manual.indd
PAGE SIZE: L5.5″ H4.25″ L13.97cm H10.795cm
BOOKLET FORMAT; SADDLE-STITCHED BINDING
BLEED: .125″ on all sides

PRINTER SPECIFICATIONS

SCALE: 100%
MATERIALS:

• 250g C2S
• Printed double-sided: 4C

DO NOT PRINT COMMENTS, SCORING, OR DIELINES LAYERS!

Physical sample according to specs must be approved
by JETSON Bike before proceeding to production.
COMMENTS (Internal reference only)
File created by Eitan Adika, Jangmu Lama
& Angelina Zavilevich

FCC statement 
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.

What’s in the Box

1. LED Lights
2. Charging Port
3. Power Button
4. Charger

Please Note. Images may not reflect exact appearance of actual product.

Specs & Features

• Weight Limit: 220 lb
• Product Weight: 22 lb
• Recommended Age: 12+
• Tire Size: 6.5”
• Product Dimensions: L23.5” x W8” x H7”
• tax Speed: Up To 12 mph
• Max Range: Up To 10 Miles
• Battery: 24V, 4.OAh Lithium-ton
• I Motor: 4OOW, Dual Hub / lotor
• Charger: UL LISTED, 110-240V
• Charge Time: Up To 3 Hours
• Climbing Angle: Up To 15°

Remember to be safe and most importantly, hove fun 

Get Started

Charging the Battery

• Only use the included charger
• Plug the charger into the wall before the Charging Port
• Don’t turn on the Rove while it’s charging
• Charge the battery until it is fully charged up to 3 hours

Indicator Lights

Status Light: If this light turns red or if you ore having issues with the Rave, you may need to recalibrate it.
Balance Light: Active Balance Technology is on, which levels the Rove as you ride.
Power Light: The Rave is powered on.

Warning: The Rove will automatically turn off once the battery power goes below 10°4 as a safety precaution.

How to Recalibrate

Follow these 3 simple steps…

1. Place the Rave on a flat, level surface.
2. Hold the Power Button (for about 5 seconds) until you ore notified of a successful recolibration.
3. Restart the Rave by turning it off and then on.

Make Moves

Riding the Rove 

Adults must assist children in the initial adjustment procedures of the product.

Connecting to Bluetooth

The Rave comes equipped with two Bluetooth modules – one for the Bluetooth ^ speaker and one for the Ride Jetson app.

To connect to your Bluetooth® speaker:

• • Turn on the Rave, and it will become discoverable to your handheld device
• Activate your Bluetooth® in your handheld device’s settings.
• Find the Rave in your handheld device’s list and select it.
• Now you can play your music.

To connect to the Ride Jetson app:

• open the Ride Jetson app on your handheld device.
• Tap the Bluetooth symbol in the top left corner of the app.
• Select your Rave. Default password is 000000. (To customize your password go to Settings in the App. If you forget your new password, you can factory reset the Rave by recalibrating).
• You should now be connected to the Rave!

MODE SETTINGS
In the Ride Jetson app you can choose from three settings:

• Beginner Mode Max Speed: Up to 8 mph
• Intermediate Mode Max Speed: Up to 10 mph
• Advanced Mode Max Speed: Up to 12 mph

NOTE: Other features that can be adjusted include Steering Sensitivity, Driving Force, and Auto Shutdown Time.

If you are having issues connecting to Bluetooth®, folow these steps:

1. Try restarting the Rave by turning it off and then on.
2. Click the Scan button to refresh.
3. Restart the Ride Jetson app.
4. Contact Jetson Customer Support for assistance.

Care & Maintenance

RIDING RANGE
The maximum range is 10 miles. However, many factors will affect how far you can go per charge:

• Driving Surface: A smooth, flat surface will increase driving distance.
• Weight: More weight means less distance.
• Temperature: Ride, charge, and store the Rave above 50°F.
• Maintenance: Timely battery charging will increase driving distance.
• Speed and Driving Style: Frequent starting and stopping will reduce driving distance.

CLEANING THE RAVE
To clean the Rave, carefully wipe with a damp cloth, then dry with a dry cloth. Do not use water to clean the Rave, as the electrical and electronic systems may get wet, resulting in personal injury or malfunction of the Rave.

BATTERY

• Keep away from fire and excessive heat.
• Avoid intense physical shock, severe vibration, or impact.
• Protect from water or moisture.
• Do not disassemble the Rave or its battery.
• If there are any issues with the battery, please contact Jetson Customer Support.

STORAGE

• Fully charge the battery before storing. The battery should be fully charged once a month after this.
• Cover the Rave to protect against dust.
• Store the Rave indoors, in a dry place.

MODIFICATIONS
Do not attempt to disassemble, modify, repair, or replace the product or any components of the unit without instruction from Jetson Customer Support. This will void any warranty, and can lead to malfunctions which may cause injury.

ADDITIONAL OPERATION CAUTIONS
Do not lift the product off the ground while it is on and the wheels are in motion. This can result in freely spinning wheels, which may cause injury to yourself or others nearby. Do not jump on or off the product, and do not jump while using it. Always keep your feet firmly planted on the mat sensors while in operation. Always check the battery charge before using.

DISPOSAL OF USED BATTERY
Battery may contain hazardous substances which could endanger the environment and human health. This symbol marked on the battery and/ or packaging indicates that used battery shall not be treated as municipal waste. Batteries should be disposed of at an appropriate collection point for recycling. By ensuring the used batteries are disposed of correctly, you will help preventing potential negative consequences for the environment and human health. The recycling of materials will help to conserve natural resources. For more information about recycling of used batteries, please contact your local municipality waste disposal service.

The Bluetootho word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. And any use of such marks by Jetson Electric Bike LLC. is under kens.. other trademarks and trade names are those of their respective owners.

Apple, the Apple logo, iPhoneg are trademarks of Apple inc., registered in the U.S. and other countries. App store is a service mark of Apple inc., registered in the U.S. and other countries.

Google Play and the Google Play logo ore trademarks of Google Inc.

Safety Warnings

• Before use, please read the user manual and safety warnings carefully, and make sure you understand and accept all the safety instructions. The user will be responsible for any loss or damage caused by improper use.
• Before each cycle of operation, the operator shall perform the preoperation checks specified by the manufacturer: That all guards and pads originaly supplied by the manufacturer are in proper place and in serviceable condition; That the braking system is functioning properly; That any and all axle guards, chain guards, or other covers or guards supplied by the manufacturer are in place and in serviceable condition; That tires are in good condition, inflated properly, and have sufficient tread remaining; The area that the product is to be operated should be safe and suitable for safe operation.
• Components shall be maintained and repaired in accordance with the manufacturer’s specifications and using only the manufacturer’s authorized replacement parts with installation performed by dealers or other skied persons.
• Don’t allow hands, feet, hair, body parts, clothing, or similar articles to come in contact with moving parts, wheels, or drive train, while the motor is running.
• This product should not be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction (IEC 60335-1/A2:2006).
• Unsupervised children should not play with the product (IEC 60335-1/A2:2006).
• Adult supervision is required.
• The rider should not exceed 220 lb.
• Never use near motor vehicle.
• Units shall not be operated to perform racing, stunt riding, or other maneuvers, which may cause loss of control, or may cause uncontroled operator/passenger actions or reactions.
• Avoid sharp bumps, drainage grates, and sudden surface changes. Scooter may suddenly stop.
• Avoid streets and surfaces with water, sand, gravel, dirt, leaves, and other debris. Wet weather impairs traction, braking, and visibility.
• Avoid riding around flammable gas, steam, liquid, or dust that could cause fire.
• Operators shall adhere to all of the manufacturer’s recommendations and instructions, as well as comply with all laws and ordinances: Units without headlights shall be operated only with adequate daylight conditions of visibility, and; Owners shall be encouraged to highlight (for conspicuity) using lighting, reflectors, and for low-riding units, signal flags on flexible poles.
• Do not ride at night.
• Only ride the product with adequate daylight conditions for visibility.
• Persons with the following conditions shall be cautioned not to operate: Those with heart conditions; Pregnant women; Persons with head, back, or neck ailments, or prior surgeries to those areas of the body; and persons with any mental or physical conditions that may make them susceptible to injury or impair their physical dexterity or mental capabilities to recognize, understand, and perform all of the safety instructions and to be able to assume the hazards inherent in unit use.
• Do not ride after drinking or taking prescription medication.
• Do not carry items when riding.
• Never operate the product barefooted.
• Always wear shoes and keep shoelaces tied.
• Make sure your feet are always placed securely on the deck.
• Operators always shall use appropriate protective clothing, including but not limited to a helmet, with appropriate certification, and any other equipment recommended by the manufacturer: Always wear protective equipment such as helmet, knee pads, and elbow pads.
• Always give way to pedestrians.
• Be alert to things in front and far away from you.
• Do not allow distractions when riding, such as answering the phone or engaging in any other activities.
• The product cannot be ridden by more than one person.
• When you ride the product along with other riders, always keep a safe distance to avoid a collision.
• When turning, be sure to maintain your balance.
• Riding with improperly adjusted brakes is dangerous and can result in serious injury or death.
• Applying brakes too hard or too suddenly can lock up a wheel, which could cause you to lose control and fall. Sudden or excessive application of the brake may result in injury or death.
• The brake may become hot while operating, do not touch the brake with your bare skin.
• If the brake loosens, please adjust with the hexagon wrench, or please contact Jetson Customer Support.
• Replace worn or broken parts immediately.
• The area that the product is to be operated should be safe and suitable for safe operation.
• Check whether all safety labels are in place and understood before riding.
• The owner shall allow the use and operation of the unit after a demonstration that such operators can understand and operate al components of the unit before use.
• Recommended for indoor use.
• Use caution when charging. Do not operate charger near flammable materials. Unplug charger and disconnect from scooter when not in use.
• When the battery is fully charged, stop charging and unplug the unit.
• Prolonged exposure to UV rays, rain and the elements may damage the enclosure materials, store indoors when not in use.

California Proposition 65
 WARNING:

This product can expose you to a chemical such as Cadmium that is known to the state of California to cause cancer or birth defects or other reproductive harm. For more information go to www.p65warnings.ca.gov/product

NOTICE OF COMPLIANCE
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
  Shielded cables must be used with this unit to ensure compliance with the Class B FCC limits.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation.

Enjoying the ride?
Leave a review on ridejetson.com/reviews or share your photos with us online using the #RideJetson hashtag!

Questions? Let us know.
support.aidejetson.com

Hours of Operation: 7 Days a Week, 10am-6pm
US 1-(888) 976-9904 I UK +44 (0)33 0838 2551

Manufactured in Vongkang, China Imported by Jetson Electric Bikes LLC. 1 Rewe Street, Brooklyn, New York 11211
www.rideietson.com

Follow us @ridejetson #MakeMoves

Date Cod: 03/2020