TRULY WIRELESS EARBUDS
Manual

AIRTIME PRO Earbuds Instructions

Introduction
Welcome to Truly Wireless Audio. Now, you never need to plug your earbuds in again. AIRTIME PRO Truly Wireless earbuds free you to enjoy music without anything holding you back.

Pairing the Wireless Earbuds with Your Device

1. Simply open the case and remove the buds. A pairing signal will be sent to your Bluetooth® device. The earbuds will flash white and red, indicating pairing mode.
2. Ensure your device’s Bluetooth® connection is on and select “IFROGZ Airtime Pro.”
3. Complete any additional paring steps based on your device. The earbuds’ lights will flash white and then turn off, indicating that pairing was successful. Congrats, your wireless earbuds are now ready to use!

Turning Earbuds On/Off
To turn the earbuds on, simply remove the buds from the case.
If you would like to use only one bud, simply remove the right earbud from the case. The right earbud is the primary bud and can be used without the other. Please note, the left earbud will not work alone unless the right earbud is also removed from the case.

To turn earbuds off, simply return them to the case. You can also press and hold the IFROGZ icon on the earbud for ten seconds to turn it off; it will flash red indicating power is off.

The earbuds will go into hibernation mode if not used for 20 minutes.

Using the Earbuds
AIRTIME PRO has built-in touch navigational controls. Simply tap on the end of the earbud (on the IFROGZ logo) to navigate.

Charging the Wireless Earbuds
The case carries enough power to charge the earbuds up to 3 times. *To charge them:

1. Place them in the charging case.
2. A red light on the earbuds will indicate charging. When the red light disappears, they are fully charged.
3. Recharge the case, if needed.

*Based on 50% volume and 5 hours of playtime.

Charging the Case
Your case comes charged and ready to go, but here’s how to recharge it when you need to:

1. Connect the included USB-C charging cable to the port on the back of your case.
2. Connect the USB-A end of the included cable to your preferred 5V USB outlet.
3. The Battery Indicator will flash according to its current battery level. This indicates your case is charging.
4. Wait for the Battery Indicator lights to turn off, indicating your case is fully charged.
5. Disconnect the charging cable and enjoy your new, portable power.

Checking the Battery Level

Your case carries enough power to charge your wireless earbuds up to 5 times, for a total of up to 20 hours. To check how much power it still carries:

1. Place the buds in the case. The LED on the front of the case will illuminate indicating how much battery remains:
   a. If it lights up completely, 75% or more remains.
   b. If it lights up ¾ of the way, between 50-74% remains.
   c. If it lights up ½ of the way, between 25-49% remains.
   d. If it lights up ¼ of the way, less than 24% remains.
2. Recharge your case whenever you wish.

Factory Reset
A factory reset can help with some troubleshooting issues. Here’s how to perform one:

1. Place both buds in the case.
2. Reset the right bud.
   a. Remove the right bud from the case.
   b. Tap and hold for 10 seconds until light flashes red and turns off.
   c. Tap and hold for five seconds until light turns on and flashes red and white.
   d. Quickly tap the bud six times, the light will turn off.
   e. Return the bud to the case.
3. Reset the left bud.
   a. Remove left bud from the case.
   b. Quickly tap the bud six times, the light will turn off.
   c. Return the bud to the case.
4. Connect left and right.
   a. Remove both buds from the case and allow them to connect to each other for about five seconds.
5. Connect as normal.
   a. The buds are now reset to factory settings. Remove them from the case and pair them as normal.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS OR CHANGE TO THIS EQUIPMENT. SUCH MODIFICATIONS OR CHANGE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End-user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Drivers / Pilotes / Conductores: 8mm

©2019 ZAGG Inc All Rights Reserved
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by ZAGG Inc is under license. Other trademarks and trade names are those of their respective owners. Trademarks are property of ZAGG IP Holding Co., Inc.

IFROGZ Airtime Pro 2 Truly Wireless Earbuds

Introduction

Welcome to truly wireless audio with 30 hours· total of battery life and quick charging case.

Pairing the Wireless Earbuds with Your Device

1. Simply open the case and remove the earbuds.
   A pairing signal will be sent to your Bluetooth® device.
   The earbuds will flash red and white, indicating pairing mode.
2. On your device go to Bluetooth under Setting and select IFROGZ® Airtime Pro 2
3. Complete any additional steps your device may require.
   The lights on the earbuds will flash white and then turn off, indicating that pairing was successful.

Turning Earbuds On/Off

To turn the earbuds on, simply remove the buds from the case.

If you’d like to turn on individual bud on, press and hold the touch sensor on the earbud for 3 seconds. It will flash white until it’s connected too device. It will turn off if not paired within 20 minutes.

To turn the earbuds off, simply return them to the case.
You con also top and hold the IFROGZ icon on the earbud for 10 seconds to turn it off; it will flash red, indicating the power is off.

The earbuds will go into hibernation mode if not used for 20 minutes.

Using the Earbuds

Airtime Pro 2 true wireless earbuds hove built-in touch navigational controls. Just top on the end of the earbud= (on the IFROGZ logo} to navigate.

Music Controls

Left  Bud		Actions		Right Bud
	Play/Pause	●	Quick Tap		Play/Pause
	Play/Pause	●●	2x Taps		Next Track
	Decrease Volume		Tap & Hold		Increase Volume

Call Controls

	Answer Call/ End Call	●	Quick Tap		Answer Call/ End Call
	Cancel Call		Tap & Hold		Cancel Call
	Siri/Voice Command	●●●	3x Taps		Siri/Voice Command

Charging the Wireless Earbuds

The case carries enough power to charge the earbuds up to5times”‘.

1. Place the earbuds in the charging case. You’ll feel them magnetically dick into place.
2. A red light on the earbuds will indicate charging. When the red light turns off, they ore fully charged.

Charging the Case

Your case comes charged and ready to go. You can re-charge the case wirelessly using a wireless charging pad, or charge the case manually using the included USB-C cable.

Wireless Charging

1. Simply drop the charging case on a compatible wireless charging pad.
2. The Battery Indicator light will flash according to its current battery level. This indicates your case is charging. When the case is fully charged, all four lights will turn off within 60 seconds.

Manual Charging

1. Connect the included USB-C charging cable to the port on the side of your case.
2. Conned the USB-A end of the cable to your preferred 5V USB outlet.
3. The Battery Indicator light will flash according to its current battery level. This indicates your case is charging. When the case is fully charged, all four lights will illuminate and then turn off.
4. Disconnect the charging coble.

Quick Charge Feature

Get one more hour of playtime by nesting the earbuds in the charging case for ten minutes.

Checking the Battery Level

Your case carries enough power to charge your wireless earbuds 4 times for o total of 25 hours. To check how much power your case still has, place the earbuds in the case.
The LEO on the front of the case will illuminate, indicating how much battery remains in the case:

• If it lights up completely, 75% or more remains
• If it lights up 3/ ~ of the way, between 50-74% remains
• If it lights up½ of the way, between 25-49% remains
• If it lights up v~ of the way, less than 24% remains.

Factory Reset

If you hove functionality issues, o factory reset can help. Here’s how to perform one.

1. Place both buds in the case.
2. Reset the right bud.
   a. Remove the right bud from the case.
   b. Top and hold for 10 seconds until light flashes red and turns off.
   c. Top and hold for five seconds until light turns on and flashes red and white.
   d. Quickly top the bud six times; the light will turn off.
   e. Return the bud to the case.
3. Reset the left bud.
   a. Remove left bud from the case.
   b. Quickly top the bud six times, the light will turn off.
   c. Return the bud to the case.
4. Connect the left and right earbuds by removing them from the case and allowing them to connect to each other for about five seconds.
5. The buds are now reset to factory settings.
   Remove them from the case and pair with your device as normal.

STATEMENT OF COMPLIANCE:
Hereby, ZAGG declares that the radio equipment type for AT Pro2 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.zagg.com/en_us/cert_red

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS OR CHANGE TO THIS EQUIPMENT. SUCH MODIFICATIONS OR CHANGE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Drivers: 6mm Resistance: 16 Ohms ± 15% Sensitivity: 95d8 ± 3d8 Frequency: 50Hz – 20KHz Working Time: 5+25hrs Charging Time: l.5-2h

Warranty information available at www.zagg.com
©2020 ZAGG Inc All Rights Reserved I NASDAQ: ZAGG I MADE IN CHINA
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by ZAGG Inc is under license.
USB-C is a trademark of USB Implementers Forum.
Other trademarks are property of ZAGG.
*All hours usage and charging claims are estimates based on internal testing and will vary based on individual usage.

IFROGZ Plugz Wireless Bluetooth Earbuds

Specifications

• FEATURES: Sweat Resistant
• BRAND: iFrogz
• COLOR: Silver
• ASSEMBLED PRODUCT DIMENSIONS (L X W X H): 0.39 x 3.60 x 7.00 Inches
• WATERPROOF RESISTANCE: IPX2

Introduction

The iFrogz Plugz Wireless Bluetooth Earbuds allow you to listen to music on the go. These wireless earphones clip to your shirt collar, making it easy to access music and call controls. When not in use, the iFrogz Bluetooth earphones contain a magnetic clip that keeps them safely stored. They offer a magnificent sound with a complete spectrum of frequencies thanks to 9mm drivers. The sweat-resistant earbuds satisfy IPX-2 requirements, allowing you to listen to music during your workout. They come in a variety of colors and come with three sizes of ear tips to ensure a secure fit.

PRODUCT OVERVIEW

INTRODUCTION

The Plugz Wireless Earbuds let you plug into your music – without the wires. Here’s how to get the most out of them. To download this manual, visit www.zagg.to/manuals

WIRELESS HUB

Your Plugz Wireless Earbuds feature a wireless hub that houses all the music and call controls for easy access. When you’re not using your earbuds, the magnetic Storage Clip™ makes cable management easy; simply wrap the earbud cables around the wireless hub and secure in place with the Storage Clip. Whether they’re in your ears or in your pocket, the Plugz Wireless Earbuds are made to move. Below is a quick reference for how to use the wireless hub:

BUTTON FUNCTIONS

Raised bump button (Up button)

• Quick press – Volume up
• Long press – Track next song

Middle button (Center button)

• Quick press – Play/Pause/Answer call/End call
• Medium press – Voice control (Siri® and Android®)
• Long press – Power on/Power off/Deny call

Recessed groove button (Down button)

• Quick press – Volume down
• Long press – Track previous song

POWER AND PAIR

• Press and hold the Power button until the LED flashes red and blue.
• Ensure your device’s Bluetooth® connection is on and select “IFROGZ Plugz”. Complete any additional pairing steps based on your device. The LED will flash blue every five seconds while your earbuds are on and paired.
• To turn your earbuds off, press and hold the Power button for six seconds. The LED will flash red until they are powered off.
• The next time you turn on the earbuds they will automatically connect to your device.

NOTE: If you are pairing with a new device, with your earbuds off, press and hold the Power button for five seconds until the light flashes red and blue, indicating pairing mode.

CHARGE

To charge your earbuds, connect the micro-USB end of the included charging cable to the port at the end of the wireless hub and the USB end to your preferred USB outlet. The LED will light red while they are charging and will turn off when they are fully charged.

Play Music

• Press the Play button to begin playing your music.
• While music is playing, press Play quickly to pause it. Press Play quickly again to resume.
• Quick-press the Volume Up or Volume Down buttons to control your audio volume.
• Press and hold the Volume Up or Volume Down buttons to track forward and back through your playlist.

TAKE CALLS

• Press the Play button to answer an incoming call.
• Press and hold the Play button for three seconds to send an incoming call to your voicemail.
• Press the Play button during a call to disconnect.

Frequently Asked Questions

• What is the best way to attach my Ifrogz plugz?
  Hold the Power button down until the LED turns red and blue. 2. Turn on the Bluetooth® connection on your smartphone and choose “IFROGZ Plugz.” Depending on your device, you may need to complete extra pairing steps.
• What are your thoughts on the iFrogz earbuds?
  For five seconds, press and hold the Power button until the light flashes red and blue, signifying pairing mode.Select “IFROGZ Resound Wireless” on your device. Depending on your device, you may need to complete extra pairing steps.
• On iFrogz, how do I change the volume?
  To start playing your music, press the Play button.
  To halt music while it is playing, rapidly press Play.
  To control the volume of your audio, quickly hit the Volume Up or Volume Down buttons.
• What is the procedure for pairing my iFrogz truly wireless earbuds?
  Simply open the case, and your Bluetooth device will receive a pairing signal. Pairing mode is indicated by the earbuds flashing white. 2. Turn on the Bluetooth on your smartphone and select “IFROGZ TWS.” Make sure all other Bluetooth®-capable devices are out of range or have Bluetooth® turned off.
• Why aren’t my Ifrogz communicating?
  Why won’t my earbuds connect? On Android, select Unpair (or forget, as some phones call it) from the Settings menu next to a connected device. It is necessary to recharge the battery. Even if the batteries indicate that they are still charged, consider fully charging them before pairing.
• With IFROGZ earphones, how do you answer the phone?
  To answer an incoming call, press the Play button.
  To send an incoming call to voicemail, press and hold the Play button for three seconds.
  During a call, use the Play button to disconnect.
• Why are my IFROGZ constantly disconnecting?
  The red led shutting off usually signifies that the earbuds are charged. Make sure the earphones are in the charging case, then press and hold the charge case button for 7 seconds. Last but not least, before pairing, make sure the device’s Bluetooth is switched off and then on.
• IFROGZ is compatible with Android.
  iFrogz wireless earbuds are low-cost Bluetooth headphones that connect to your iPhone, Android, Mac, or Windows device to allow you to listen to music, talk, and view movies without having to plug in a wire.
• What is the procedure for resetting my IFROGZ?
  For 10 seconds, tap and hold the IFROGZ logo until the light flashes red and shuts off. c. For five seconds, tap and hold the IFROGZ logo until the light goes on and flashes red and white. d.
• On IFROGZ, where is the power button?
  Simply open the casing to activate the earbuds. Press and hold the main button for three seconds to turn on a single bud. Until it is connected to a device, it will blink white.

CHARGE PAD
WIRELESS CHARGE PAD

Introduction

Welcome to the wonderful world of wireless charging! With the Wireless Charge Pad and its transfer speeds of up to 10W*, you’ll never need to plug your phone in again.

How to Use

1. Make sure your phone is Qi-enabled and capable of wireless charging.
2. Connect the charging pad to a power source using the charging cable.
   The indicator light will illuminate for three seconds when connected to a power source.
   
3. Place your device on the charging pad. For the most effective charging, make sure it’s in the center of the pad. When the device is charging successfully, the  LED indicator will light up for 16 seconds then turn off.

Having Problems?

If your device doesn’t charge or the LED light won’t stop flashing, there may be a problem with your phone case. Cases that are metallic or over 6mm thick don’t work with the Wireless Charge Pad. For best charging, don’t attach anything metallic, including bank cards with metallic strips, to your phone. Third-party cables and adapters can also cause charging problems.

For Best Results

1. Keep the charger away from water or liquid.
2. Make sure the power is off before cleaning the charger.
3. Only use the charger indoors

Still, Having Trouble?

Our IFROGZ customer support team is available should you have any needs:
Online: www.support.zagg.com
Or give us a call at 1-800-700-9244

FCC Caution: FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   (1) This device may not cause harmful interference, and
   (2) This device must accept any interference received, including interference that may cause undesired operation.
2. any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be  determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

Warranty information is available at www.zagg.com/warranty-policies
©2020 ZAGG Inc All Rights Reserved | NASDAQ: ZAGG | MADE IN CHINA
Universal wireless charging is compatible with Qi-enabled devices.
Qi is a trademark of the Wireless Power Consortium.
Other trademarks are property of ZAGG.
Charging results will vary by device. All charging claims are estimates based on internal testing and will vary based on individual usage.

AIRTIME™PRO 2 SE
TRULY WIRELESS EARBUDS
Quick Start Guide

Factory Reset

1. If you have functionality issues, a factory reset can help. Here’s how to perform one.
   Place both buds in the case.
2.  Reset the right bud.
   a. Remove the right bud from the case.
   b. Tap and hold for 10 seconds until the light flashes red and turns off.
   c. Wait 10 seconds after the red flashing light.
   d. Tap and hold for five seconds until the light turns on and flashes red and white.
   e. Quickly tap the bud six times; the light will turn off.
   f. Return the bud to the case.
3.  Reset the left bud.
   a. Repeat steps above, same as right bud.
4. Connect the left and right earbuds by removing them from the case and allowing them to connect to each other for about five seconds. Once connected to each other, earbuds will flash red and white indicating pairing mode. Remove the right bud from the case.
5. The earbuds are now reset to factory settings. You will need to remove the previous pairing from your device’s Bluetooth® settings. Once removed, follow pairing instructions at the beginning of this quick start guide.

Having Trouble?

Our IFROGZ customer support team is available should you have any needs:
Online: kwww.support.zagg.com
Or give us a call at 1-800-700-9244

Introduction

Welcome to truly wireless audio with 25 hours* of combined battery life and wireless charging case.

Simple Pairing

1. Remove earbuds from the case and remove the protective cover from contacts. Place earbuds in the charging case and allow 5 minutes to charge.
   
2. Open the case and remove earbuds to initiate Bluetooth® pairing.
   
3. On your device’s Bluetooth menu, select “IFROGZ Airtime Pro 2 SE.”
   

Touch Controls

Using the Earbuds

Airtime Pro 2 SE true wireless earbuds have built-in touch navigational controls. Just tap on the end of the earbud (on the IFROGZ logo) to navigate.

Turning Earbuds On/Off

To turn the earbuds on, simply remove the buds from the case. To turn the earbuds off, simply return them to the case.
The earbuds will go into hibernation mode if not used for 20 minutes.

Getting the Best Fit

To get the best sound out of your earbud, you need to have the right size ear tip to form a good seal. That’s why we provide different-sized tips.
If your ear tip feels loose, try a larger size. If you feel too much pressure, or if the ear tip doesn’t fit inside your ear, try a size smaller.
Note: each of your ears may require a different-sized tip.
To see if you’ve got a good seal, try the yawn test. Put in your earbuds and give a nice yawn; if your earbuds don’t wiggle and don’t break the seal, then you’ve got a good fit.

Charging the Wireless Earbuds

The case carries enough power to charge the earbuds up to 4 times*.

1. Place the earbuds in the charging case. You’ll feel them magnetically click into place.
2. A red light on the earbuds will indicate charging.

Charging the Case

Your case comes charged and ready to go. You can re-charge the case wirelessly using a wireless charging pad, or charge the case manually using the included USB-C® cable.

Wireless Charging

1. Simply drop the charging case on a compatible wireless charging pad.
2. The Battery Indicator lights on the front of the case will flash according to its current battery level. This indicates your case is charging. When the case is fully charged, all four lights will turn off.

Manual Charging

1. Connect the included USB-C charging cable to the port on the side of your case.
2. Connect the USB-A end of the cable to your preferred 5V USB outlet.
3. The Battery Indicator light will flash according to its current battery level. This indicates your case is charging. When the case is fully charged, all four lights will illuminate and then turn off.
4. Disconnect the charging cable.

Quick Charge Feature

Get one more hour of playtime by nesting the earbuds in the charging case for ten minutes.

Checking the Battery Level

Your case carries enough power to charge your wireless earbuds 4 times for a total of 25 hours. To check how much power your case still has, place the earbuds in the case. The LED on the front of the case will illuminate, indicating how much battery remains in the case:

• If four lights illuminate, 75% or more remains
• If three lights illuminate, between 50-74% remains
• If two lights illuminate, between 25-49% remains
• If one light illuminates, less than 24% remains.

This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS OR CHANGES TO THIS EQUIPMENT. SUCH MODIFICATIONS OR CHANGES COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End-user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Drivers: 6mm Resistance: 16 Ohms ± 15% Sensitivity: 100dB ± 3dB Frequency: 50Hz – 20KHz Working Time: 5+20hrs Charging Time: 1.5-2h
Warranty information is available at www.zagg.com/warranty-policies
©2020 ZAGG Inc All Rights Reserved | NASDAQ: ZAGG | MADE IN CHINA
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by ZAGG Inc is under license. USB-C is a trademark of USB Implementers Forum. Other trademarks are property of ZAGG.
*All hours usage and charging claims are estimates based on internal testing and will vary based on individual usage.

314-00849 | 07/15/20