HAVIFLEX Product Information

The HAVIFLEX is a flexible LED strip light that comes in
different color temperatures and an RGB option. It is suitable for
both indoor and outdoor use with an IP67 rating that makes it
resistant to water and dust. The product comes with installation
instructions that should be read carefully before use and kept for
future reference. The LED strip should be checked before
installation to ensure all components are working correctly. The
product has cutting marks that allow it to be cut to the desired
length, and soldering is required to connect wires to the strip.
The product requires a 24V DC isolated power supply with a ripple
wave of less than 5%.

HAVIFLEX Product Usage Instructions

1. Before installation, ensure all components, including the
   HAVIFLEX and LED driver, are working correctly. If any product is
   not working correctly, contact the shop where items were purchased
   for next steps.
2. Follow the correct bending methods to avoid damaging the LED
   strip.
3. Use screws to fix the clips when installing the LED strip, with
   a minimum of four clips to be used for every meter of the
   strip.
4. When installing the LED strip, install it from both ends
   simultaneously. Installation from one direction is prohibited.
5. If the length of the LED strip is over 2 meters, it is
   recommended to install or remove it by two persons.
6. Cut the LED strip to the required length using the cutting
   mark. Only parts with cutting marks can be cut.
7. Connect the wires with the LED strip using a soldering iron,
   making sure to pay attention to positive and negative poles.
8. After injecting silicon into the cap, push the cap onto the LED
   strip and fill the end of the LED strip with filler. The LED strip
   should be placed horizontally for two hours until the plug surface
   is dry.
9. When installing in a channel and in a facing down direction,
   apply adhesive or double-sided tape to prevent the HAVIFLEX from
   falling out of the channel.

View Fullscreen

HAVIFLEX INSTALLATION INSTRUCTIONS

PRODUCT CODES

COLOUR TEMP.

HV9792-IP67-140-3K

3000K

HV9792-IP67-140-4K

4000K

HV9792-IP67-140-5K

5500K

HV9792-IP67-336-RGB

RGB

Please read the instructions carefully before installation and application and use the product in the correct way.

Instructions on accessories are included in these instructions.

Please properly maintain these instructions after reading and understanding it for convenient reference by all users of the product in the future.

Before installation make sure all components are working including the HAVIFLEX and LED Driver.

Connect these while uninstalled, If there is any product that is not working correctly, Please contact shop where items were purchased from to work out next steps. Do not continue to install the product.

DIMENSIONS

50±0.5mm
7.14±0.5mm

5000±36mm
Single Colour

10±0.5mm

14±0.5mm 13±0.5mm

62.5±0.5mm
8.9±0.5mm

5000±36mm
RGB

8±0.2mm

6±0.5mm 11±0.5mm

7.5±0.5mm 14±0.5mm

6.5±0.5mm

7.5±0.5mm

Precautions before Installation:

Side Bend Only

Outdoor

Indoor

!

IP67 Suitable for Indoor or Outdoor Use

No stepping on

No Twisting in wrong direction
ADDRESS: 143 Beauchamp Road, Matraville, N.S.W., 2036

No stretching
Web: www havit.com.au Email: sales@havit.com.au Phone: 02 9381 8300

HAVIFLEX INSTALLATION INSTRUCTIONS
Correct Bending Methods:

Correct Way Installation Steps:

Incorrect Way

1. Use screws to fix the clips

Minimum 4 clips to be used for every 1m.

2

1

2

1

1

1. When installing the LED strip, install it from both ends at the same time, installation from one direction is prohibited.

2. To remove disassemble carefully using tool, do not pull the LED strip directly.
ADDRESS:143 Beauchamp Road, Matraville, N.S.W., 2036

> 2m
If the length of LED strip is over 2m, it is recommended to install by two persons.
> 2m
If the length of LED strip is over 2m, it is recommended to removed by two persons.
Web: www havit.com.au Email: sales@havit.com.au Phone: 02 9381 8300

HAVIFLEX INSTALLATION INSTRUCTIONS

Instructions for Cutting and Soldering:

1. Cut the LED strip to required length The minimum cutting unit should be subject to the mark of LED strip

Cutting Mark

2. Cut out a piece of light strip with proper dimensions according to requirements

3. Connect the wires with the LED strip using solder and soldering iron (pay attention to positive and negative poles)

Please note that the cutting point is visible as a hidden black mark inside the strip.
4. Place the plug with a hole into the wires and inject Silicon into the cap.

electric soldering iron

The amount of silicon should be 1/3 to 1/2 of the Cap
Silicon

Push Onto

5. Push the cap onto the LED strip

6. Fill the end of LED strip with filler, then push the Cap onto the end of LED strip.

Silicon

After injecting silicon, the LED strip should be placed horizontally for two hours until the plug surface is dry, and then to finish the operation of plug end .

After injecting silicon, the LED strip should be placed horizontally for two hours until the plug surface is dry, and then to finish the operation of plug end .

Push Onto

Notes:
1. Only the parts with cutting marks can be cut when it is necessary to cut the silicone neon strip according to the on-site installation length; 2. When installing in Channel and in a facing down direction, an adhesive or double sided tape must be applied to prevent Haviflex from falling out of channel. 3. Use a 24V DC isolated power supply to drive the silicone neon strip and the ripple wave of constant voltage source shall be less than 5%. It is not allowed to use
RC voltage reduction or non-isolated power supply to drive the silicone neon strip. 4. When connecting multiple silicone neon strips. Wiring must be done in Parallel.
Attention should be paid to the positive and negative poles of the wires during installation and whether the power supply conforms to required voltages to avoid damages. 5. Silicone neon strip should be placed in a dry and sealed environment. It is suggested that the storage period cannot be too long. Working temperature: -20°C~ +45°C; storage temperature: 0°C~ +60°C 6. In actual applications, 20% of the power supply shall be kept (only 80% of the power is used) to guarantee that sufficient voltage is available to drive the product; 7. Attention shall be paid to safe operation. After powering on, it is not allowed to touch the AC power supply to avoid an electric shock; 8. On the premise of required direction (the top view is not same as the side view), please do not bend the strip into an arc with a diameter less than 30mm to ensure the longevity and reliability.
Product Warranty Description 1. A warranty period of three years is provided for products in normal use. For any faults arising during the period that are confirmed to be quality related by inspection of Havit Lighting, a replacement strip will be offered. 2. The warranty does not cover any of the following: (1) Any product damage due to usage not allowed in the instructions; (2) Any product damage due to disassembling or wrong operations by the user; (3) Severe appearance damage or deformation of the product.

ADDRESS: 143 Beauchamp Road, Matraville, N.S.W., 2036

Web: www havit.com.au Email: sales@havit.com.au Phone: 02 9381 8300

HAVIFLEX INSTALLATION INSTRUCTIONS
Sample Wiring Diagrams
Single Colour

RGB

RGB Controller

Waterproof power supply

RGB with multiple lengths Waterproof power supply

RGB Controller Waterproof power supply

Repeater

Notices
1. The products are subject to thermal expansion as a result of the changes in temperature to which they are subject. This thermal expansion must be taken into account in installations subject to a wide range of temperature. 2. When cleaning use only water and methylated spirits. 3. IP67 protection on the product and the continuous line system. 4. Product is not suitable for use in swimming pools and fountains.

ADDRESS: 143 Beauchamp Road, Matraville, N.S.W., 2036

Web: www havit.com.au Email: sales@havit.com.au Phone: 02 9381 8300