genexis – UseManuals https://usemanuals.com Owner's manuals for all sorts of products Wed, 28 Jun 2023 09:57:32 +0000 en-US hourly 1 https://wordpress.org/?v=6.7.2 https://usemanuals.com/wp-content/uploads/2025/02/favicon-32x32-2.png genexis – UseManuals https://usemanuals.com 32 32 genexis P2420 FiberTwist Series Manual https://usemanuals.com/genexis/p2420-fibertwist/ Wed, 28 Jun 2023 09:57:32 +0000 https://usemanuals.com/?p=133237 Read More...

]]>

genexis F2020 FiberTwist Series

Button overview

Port overview

SC/PC coupler with shutter

  • F2020 – Fiber port not functional
  • F2120 – Fiber port functional

LED overview

Installation guide

Different language versions of this document and additional product information are available on https://genexis.eu/product/fibertwist/downloads

Box contents

  •  Genexis FiberTwist (active device)
  •  Power adapter
  •  Label (self-adhesive)
  •  Installation Guide (this document)

Label position
The product label is positioned on the back of the active device.

Preparation
Ensure there is a power socket within reach of where the device is being installed.

Important: Instructions need to be followed precisely and uninterrupted. This minimizes the risk of damage to the fiber optic connectors, causing a severe degradation of signal quality.

Remove Blind Cover (if present)genexis-F2020-FiberTwist-Series-fig-4

  1.  Press and hold the unlock button (see button overview).
  2.  Rotate the Blind Cover counterclockwise till it blocks.
  3.  Remove the Blind Cover from the baseplate (FTU) by pulling it towards yourself.
  4.  Store the Blind Cover in a safe place.

Remove dust cap

  1.  Take the FiberTwist out of the box.
  2.  The dust cap is connected to the red string located on the rear of the FiberTwist.
  3.  Remove the dust cap by pulling the red string.
  4.  Store the dust cap in a safe place.

Twist!

  1.  Place the FiberTwist on the FTU as shown in the picture below, in a 30–degree angle.
  2.  Rotate clockwise until it clicks into place.
  3.  Make sure the FiberTwist is aligned squarely on the FTU, each edge must line up directly with the FTU below.

Your FiberTwist is now installed!

Connecting the FiberTwist

  1.  If required, connect your television / set-top box to the TV port with a coax cable.
  2.  F2120 only: open the blue shutter from the SC/PC coupler, connect your fiber gateway to the SC/PC port using a fiber patch cable.
  3.  Connect the supplied power adapter to the FiberTwist and plug the adapter into a power socket.

If at some point in the future it becomes necessary to uninstall the FiberTwist, please place the Blind Cover back on the FTU immediately and put the dust cap back on the FiberTwist.

EU Declaration of Conformity

Hereby, Genexis B.V. declares that the product FiberTwist-F2020/F2120 is in compliance with Directives 2014/30/EU, 2014/35/EU, 2011/65/EU, Delegated Directive 2015/863 and Ecodesign Directive 2009/125/EC.
The full texts of the EU declaration of conformity are available at the following internet address: https://genexis.eu/red/ft-F2020-F2120 

Company Name
Genexis B.V.
Company Address
Lodewijkstraat 1a
5652 AC Eindhoven
The Netherlands
Name and title of authorized person
Maarten Egmond, CTO

]]>