FuRRION 2-Zone Entertainment Soundbar

• Digital FM tuner with 10 presets
• 2-zone audio distribution (1 internal, 1 external)
• 2-zone video distribution
• 2 analog stereo inputs on rear panel

2-ZONE ENTERTAINMENT SOUNDBAR

Specifications

Operating Voltage                            DC9-16V
Max Power Consumption                70.5W
Max Power Output Full range:        10W x 2
Subwoofer:                                       20W
Z2:                                                   10W X 2
USB Charging                                  Max 2.1A
USB Port                                         Support high speed USB 2.0 flash drive
# of RCA (Audio LR) Outputs       1
# of Video Inputs                           1
# of Video Outputs                       2
# of HDMI Outputs                      1
# of HDMI Inputs                         1
# of 3.5mm AUX-IN                     1
# of Zone Audio Outputs             2 (Internal x 1 , External x 1)
Radio Coverage                             FM 87.5 -107.9 MHZ
Bluetooth Effective Range            Up to 30 feet
Operating Temperature                 -20 °C to 60 °C /-4 °F to 140 °F

Packaging Information

Packaging Type                                                           Brown Box
Quantity Per Box (pcs)                                                1
Individual Packaging Dimensions (L x H x W) 33⁄” x 5” x 7” (858 x 145 x 190mm)
Individual Packaging Gross Weight (kg/lbs)                2.6/5.7
Individual Packaging Net Weight (kg/lbs)                    2.2/4.8

Master Carton

Packaging Type                                                 Master Carton Box
Quantity Per Box (pcs)                                     4
Master Carton Dimensions ( L x H x W)         34” x 12” x 15” (858 x 315 x 398mm)
Master Carton Gross Weight (kg/lbs)              12/26.5
Master Carton Net Weight (kg/lbs)                  8.8/19.4

SA Innovation Center & Institute of Technology: 52567 Independence Ct. Elkhart, IN 46514

Customer Service & Technical Support: Email: support@furrion.com Tel : (888) 354 5792 www.furrion.com

Furrion® and the Furrion logo are trademarks licensed for use by Furrion Ltd. and registered in the U.S. and other countries. © 2007-2019 Furrion Ltd.

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Furrion Ltd. is under license. Other trademarks and trade names are those of their respective owners. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Furrion Digital Wireless Camera System

Designed for 5th Wheel, 1W, Caravan, and Trailer applications Furrion’s new easy install wireless camera kit comes in two parts,

1. Furrion mount bracket prep kit. Part No. FRCBRKT-BL
2. Furrion Camera and Monitor Kit. Part No. FRC12TA-BL

Check if your RV or Trailer has been pre-installed with the mounting bracket prep kit.

Safety Instructions

Please read these instructions carefully before installation and operating your Furrion reversing camera unit.

The following symbols are used throughout this manual to indicate potentially dangerous situations or mark important safety instructions.

WARNING: Indicates a potentially dangerous condition. Use extreme caution when performing this task.

CAUTION: Indicates a critical procedure for the safe and proper operation of the controller.

NOTE: Indicates a procedure or function that is important for the safe and proper operation of the controller.

General Safety Information

• Read all of the instructions and cautions in the manual before beginning installation.
• There are no user-serviceable parts inside the Furrion Rear camera system Do not disassemble or attempt to repair any part of the camera system.
• Disconnect all sources of power to the camera before installing.
• There are no fuses or disconnects on the Furrion reversing camera unit. Install external fuses/breakers as required.
• Do not allow water to enter the LCD Display.
• Connect 12/24V power cable to the camera unit u§ing waterproof

Excessive heat can be caused by a loose connection.

Caution:
A battery or 12/24V DC electrical system presents a risk of electrical shock or burn hazard. Ensure all power sources are isolated before installation.

Warning:
These installation instructions are for use by qualified personnel only. To reduce the risk of electric shock, do not perform any servicing other than that specified in the operating instructions.

Caution:
To reduce the risk of fire, connect the camera only to a circuit provided with a maximum branch-circuit overcurrent protection device.

Note:
Ensure watertight connectors which connect the camera power supply cable to a power source.

Warning:
Use 16AWG or larger cables to supply power to the camera unit.

V Warning:
Ensure to connect the rear camera to the correct polarity 12/24V DC power supply. Red = Positive.

Installation Safety Precautions

Use correct size cable and connectors for supplying power to your rear camera
Ensure the power supply circuit has circuit protection Connect the rear camera to an 8-30V DC circuit only
Use insulated tools when working with power supply
Use correct safety equipment when working at elevated levels
Ensure the camera prep bracket gasket is correctly sealed and weatherproof.
Ensure correct polarity of DC power supply to camera Objects in the monitor may appear closer than they appear. Reverse slowly and with care.
This rearview camera system is designed to assist the driver, it is not designed to replace rearview mirrors. Always check your mirrors.

General information

Overview:

Thank you for purchasing a Furrion reversing camera system.
Furrion’s reversing camera system is one of the easiest rearview camera systems to install in your trailer, truck, or RV. All that is required is a connection of a single DC power supply to the rear camera from a reversing power source.

The Furrion reversing camera system is using digital wireless technology giving the major benefit of superior signal transmission with low interference on a single bandwidth channel. This means the Furrion camera unit eliminates the interferences which other analog signal systems are subject to, meaning the Furrion digital system gives you a clearer picture of what is behind you no matter where you are.

This Furrion system with an integrated antenna attached to the camera has been specifically designed for use on trailers, trucks, 5th wheels, caravans, and RV’s. This system has been designed for extended range applications or security monitoring.

Features:

This unit can be used as a reversing camera, tow hitch monitor or security monitor.

This unit features:
Wide-angle viewing lens
Night vision LED lights
Camera mounting bracket to reduce glare
Digital wireless signal for clear picture quality
Easy installation
Adjustable camera angle

Installation

FRCBRKT-BL

Furrion reversing camera mounting bracket installation:

The Furrion reversing camera prep kit includes:
1 x Reversing camera mounting bracket
1 x Mounting bracket gasket
1 x 6ft power cable
1 x Removable Bracket cover

When wiring the Furrion camera system as a rearview camera, the power supply for the camera unit must come from a 12V trigger power source or transmission wiring. The power source can also come from the 7 way connection from your trailer.

For reversing camera use, mount the camera bracket in an elevated position at the rear of the trailer or RV.

Do not mount the camera in a low position.
For reversing the camera function, do not connect the camera to a constant power source.
or best results, mount the camera in a high position to increase the viewing angle.

Mounting and wiring the camera prep bracket kit

Wiring:

For using your camera kit as a reversing camera system:

1. Isolate the 12V power system
2. Find a suitable position to mount your camera mounting bracket on the rear of your trailer/coach/truck. Ensure the mounting position is centered and in an elevated position at the top area. The higher the bracket is mounted the better the viewing angle of the camera will be.
   Ensure there are no running lights or objects protruding directly under the position for mounting which will obscure camera vision.

3. Drill a hole large enough to run the 16AWG 2 core cable supplied with the mounting bracket. Ensure after drilling the hole to remove sharp edges or burrs from the edges to prevent cable damage.
4. Before running the 12V supplied power cable through the hole, ensure to feed the supplied 6ft power cable through the hole in the bracket gasket per the picture on page 8. (ensure to have the center square on the gasket facing out to the cable connector)
5. To provide power to the wireless rearview camera you will need to run a 16AWG 2 core internal cable from your 12V trigger source on the rear of your trailer/coach/truck, Furrion supply a 6ft 12V power cable provided with the mounting bracket, the added cable may be required if the distance to the trigger power supply is not long enough to reach the trigger source.
6. When connecting the cable to the 12V power source ensure to connect (+ to Red) and (— to Black)
7. Attach the camera prep mounting bracket using 4 screws to ensure the gasket is lined up correctly. Ensure the bracket is mounted tightly to ensure

Mounting bracket installation

* If the camera bracket is being mounted as a prep kit without the camera. secure the wire connector inside the bracket and attach the cover. (as above)

Installation of camera

If your RV or trailer has a Furrion reversing camera prep kit pre-installed by the OEM manufacturer. You will need to contact your local dealer or go to furrion.com to purchase a Furrion FRC12TA-BL Camera and monitor installation kit.

To install the camera onto a pre-installed mounting bracket:

1. Remove the cable cover which is held by 4 screws on the underside of the bracket
2. Locate the connector inside the prep kit mounting bracket
3. Connect the camera plug and socket together and install the camera with the 4 screws
   See below:

Monitor Installation

When choosing a location to mount the monitor, make sure the monitor is in an area that will not obstruct your vision while driving.

1. Before mounting the monitor, clean the mounting surface well.
2. Position the suction mount to the smooth surface which suits your
3. Press the suction cap against the smooth surface and press the lockdown to attach and fix the mount to the surface.
   Snap-in the monitor to the suction mount.

4. Adjust the mounting arms to suit your view angle to the monitor and tighten the screws on the mount to fix the position.
5. Route the power cable to the vehicle’s cigarette lighter socket/12/24 V power outlet. The cable must not interfere with the safe operation of the
6. Insert the small 12/24 Volt DC plug of the power cable into the right side of the monitor.
7. Plug the 12/24 Volt cigarette lighter plug into the vehicle’s cigarette lighter

To maximize the effectiveness of the suction mount, it is recommended that the application be performed under the following conditions:

• The surface temperature should be between 21 and 38 degrees Celsius. The application below 10 degrees should be avoided.
• The application should not occur in direct sunlight.

Mounting should be protected from exposure to direct sunlight for a period of 24 hours.

NOTE: UNDER EXTREME BRIGHT LIGHT CONDITIONS, THE SCREEN IMAGE MAY TAKE A FEW SECONDS TO STABILIZE. PLEASE WAIT UNTIL THE IMAGE HAS STABILIZED BEFORE BACKING UP.

Operation

Once you have fitted the camera to your trailer, RV, truck, or caravan you will need to pair the wireless camera with the LCD monitor before use.
(This is only required at initial system commissioning to pair the camera with the LCD screen.)

To connect camera unit and screen together:

1. Ensure both the rear camera and LCD display have 12/24V DC power supplied (Vehicle may need to be running and in reverse gear to supply power to camera)
2. Press the power button on the LCD display to turn on
3. Press the MENU button on the display (this will bring up 4 icons on the screen)
4. Using the up and down buttons scroll across to the PAIR icon
5. Press the power/to confirm button (short press) (“pairing” icon will be displayed)
6. Press the small button on the underside of the camera unit for 2 seconds
7. On successful pairing, OK will be displayed on the LCD display.

If there is no operation of the camera displayed on the LCD display within 30 seconds of pairing. Repeat the pairing process.

Note:

If you are having trouble pairing the devices, reduce the distance between the camera unit and the LCD display for the pairing process.

To remove or replace a paired camera from the LCD display memory, Exit the menu icons on the LCD display, then press and hold down the DOWN key for 5 seconds. This will erase all pairing memory stored on the LCD display. The pairing process must be completed again for the system to function.

LCD Display Menu Icons:

Using the Up and Down arrow buttons on the monitor, select which icon you wish to select, then press the power button to confirm the selection.

Two Camera Option: This system can support 2 separate cameras paired to a monitor.

This feature enables two separate cameras to be paired with the same monitor. The cameras can be mounted in separate locations if required. Once both cameras are paired, use the up and down buttons on the monitor to scroll between the camera views. Both cameras require a constant power supply to enable switching views.

When two cameras are paired to the system, cameras are not required to be connected to the trigger power supply, the constant power source is required to be able to scroll between cameras using the up and down buttons on the monitor.)

WARNING:
When cameras are wired to a constant power source, do not use a monitor when driving. Driving with a monitor on can be a violation in state law. Check legislation before use.

When the pairing icon is selected, a sub-menu will be displayed showing

• Master Select
• Pair 1
• Pair 2

When Pairing 1 camera, select Master Icon
When Pairing 2 cameras, select Pair 1 and Pair 2 for each camera

LCD Picture Settings Sub Menu Icons:

System testing:

1. Disconnect and rea tach the vehicle’s negative battery cable.
2. Turn the ignition key to the accessory position, do not start the vehicle.
3. Engage the parking brake, and then put the shifter in the reverse This will engage the camera unit and a picture will be displayed.
4. After testing the unit and you are satisfied with the route you have chosen for the cabling, you must permanently install it.
5. Route all wires behind interior panels or under carpeting so they are hidden.

Technical specification of LCD Display:

1. Working voltage: DC8-30V
2. Working current: 5180mA
3. Standby current: 55mA
4. Wireless communication distance: 00 FT (open area outdoors)
5. Working frequency: 2.4GHz
6. Size of LCD display: 4.3′
7. Effective pixels of LCD: 480*272
8. Sensitivity of receiver: -87±3dBm
9. Working temperature: -10/+50

Technical specification of Camera unit:

1. Working voltage: DC8-30V
2. Working current: 5220mA
3. Transmitting distance: .100 FT (open area outdoors)
4. Size of image sensor 1/4 inch Color CMOS VGA
5. Quality of image: Max.25frame/sec @ QVGA
   (frame rate adjusts dynamically according to the image)
6. Specification of the camera: Focal length f1.7mm, aperture F2.0, IR filter 850nm
7. IR emission wavelength: 850nm
8. IR view distance: 1.5M
9. IR LED lit condition: Brightness s2Lux
10. Working temperature: -10/+50

Product: 2.4GHz Digital Wireless Camera System(FCA48TA-BL)
Trade Name: FURRION
Model Name: FRC12TA-BL
Serial Model : FCA48TA-BL, FCS43TA-BL
FCC ID :2ABH3FRC12TA-BLC
Product: 2.4GHz Digital Wireless Camera System(FCS43TA-BL)
Trade Name: FURRION
Model Name: FRC12TA-BL
Serial Model : FCA48TA-BL, FCS43TA-BL
FCC ID : 2ABH3FRC12TA-BLM

This product is backed by a Furious 12-month product warranty. See the warranty card for terms and conditions.

FURRION ARCTIC Built-In Refrigerator

IMPORTANT

• Thank you for purchasing this Furrion® product. Before operating your new appliance, please read these instructions carefully.
• This instruction manual contains information for safe use, installation and maintenance of the appliance.
• Please keep this instruction manual in a safe place for future reference. This will ensure safe use and reduce the risk of injury.
• Be sure to pass on this manual to new owners of this appliance.
• The manufacturer does not accept responsibility for any damages due to disregarding these instructions.

Important Safety Instructions

General Safety Warnings

CAUTION:
Improper installation, adjustment, alteration, service or maintenance can cause personal injury or property damage. For assistance or additional information, contact Furrion customer service.

• Do not allow anything to touch the refrigerator cooling system.
• Make sure the electrical installation follows all applicable code.
• Do not bypass or change the refrigerator’s electrical components or features.
• Do not spray liquids near electrical outlets, connections, or the refrigerator components. Most liquids are conductive, which can cause electric shock, short circuit or fire.
• The refrigerator cooling system is under pressure. Do not try to repair or to recharge a defective cooling system
• The shelves have been fixed according to safety regulation. The shelves must always be retained during operation and transportation. Contact Furrion customer service if the fixing mechanism is ever compromised.
• The rear of the refrigerator has sharp edges and corners. To prevent cuts or abrasions when working on the refrigerator, use caution and wear personal protection such as cut resistant gloves, and arm protection.
• Do not store or use gasoline or any flammable vapors and liquids in the vicinity of this refrigerator.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• To avoid an electrical shock hazard, relevant actions should be performed by qualified and certified professionals. Power should always be disconnected.

Proper Disposal of the Refrigerator

Risk of child entrapment. To avoid the possibility of child entrapment, please take the following precautions before you dispose of your refrigerator.

• Remove all doors.
• Leave shelves in place so children may not easily climb inside.
• Never allow children to play with, operate, or crawl inside the refrigerator.

Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents.

Before you throw away your old refrigerator or freezer:

• Take off the doors.
• Leave the shelves in place so that children may not easily climb inside.

Refrigerants
All refrigeration products contain refrigerants, which under federal law must be removed prior to product disposal. If you are getting rid of an old refrigeration product, check with the company handling the disposal about what to do.

Parts and Features

Installation

All Furrion product referenced in this manual is to be installed in accordance with local and national codes, including the latest editions of the following standards:
USA:
− NFPA 1192
− NFPA 70
Canada:
− C22.1
− CSA Z240

What’s in the Box

1. Set the unit upright.
   NOTE: The refrigerator may have been laid on its back for transportation and delivery. This is acceptable, but must be stood up-right vertically for at least 4 hours before running the compressor to settle the compressor oil.
2. Unpack the unit, discard the packaging material appropriately.
3. Confirm everything is in the box. If anything is damaged or missing, contact your dealer.
   • Refrigerator x 1
   • Instruction Manual x 1
   • Warranty Leaflet x 1
   • Refrigerator Door Lock Cover x 1
   • Storage Lock x 1

Site Preparation

WARNING: FIRE OR EXPLOSION
Gas leaks may occur in your system and result in a dangerous situation. Always perform a leak test for possible leaks according to the manufacturer’s instructions after removing any appliance.

• Never leak test when smoking. Never use a flame.
• Do not use any appliance until connection has been leak tested and does not leak
• Remove the existing refrigerator (if applicable):
  • Unplug the 120V AC power cord from the receptacle at the rear of the refrigerator enclosure.
  • Disconnect the 12V DC leads from the refrigerator and cap the lead ends.
  • Turn off the LP gas supply to the refrigerator.
  • Disconnect the LP gas line from the refrigerator. Cap the line and verify there are no LP gas leaks.
  • Remove the screws anchoring the refrigerator to the enclosure.
  • Slide the refrigerator out from the enclosure and remove it from the RV.

Select Location

• Your new refrigerator must stand on a flat surface which should support a weight of 330Lbs (150kg). Surface must be level relative to the coach floor plane.
  NOTE: A slope that is comfortable to live with, and from normal transportation is acceptable.
• If the appliance is to be placed onto the carpet, support it with a wooden board. Do not place the appliance directly on the carpet, as the heat from the compressor may cause the carpet to fade.
• For best and most efficient operation, the refrigerator should operate within 50°F ~ 126°F (10°C ~ 52°C). If installing near large heat sources, such as furnaces, fireplaces, furnaces, etc. Ensure a thermal barrier, such as wood paneling isolates the refrigerator space as not to hinder performance of the appliance.

Refrigerator Cabinet/Enclosure Preparation

• The built-in refrigerator is designed for 0″ clearance to the sides, top. There is an intentional ¼” clearance between the back of the unit and cabinet to allow the service wire to enter the cabinet space. Frame the cabinet to the dimensions indicated below:
  

  Model	W	H	D
  FCR8DCDTA-*	23½”±1/8″	527/8″±1/8″	24″±1/8″
  FCR10DCDTA-*	23½”±1/8″	597/8″±1/8″	24″±1/8″

• Squareness of the cabinet/enclosure needs to be within the “W” & “H” dimensions described in two places on either end. The diagonal measurement should be within ⅜” from each other.
• The base support of the cabinet/enclosure must be prepared with a 0 degree slope. If the existing cabinet/enclosure has a base with a slope, shimming is required to level and support the refrigerator.
  NOTE: Cabinet/enclosures of absorption style fridges may be built with a 3 degree slope towards the rear. The slope is to allow moisture drainage towards the sidewall vent.
• The cooling system is a forced air closed loop design, with inlet and exhaust on the bottom front of the unit. The enclosure does not need to be ventilated for any purpose. There is also no need for additional insulation on sides and top of the enclosure. The enclosure can be treated as a normal cabinet enclosure of the living space
• Face surfaces of the cabinet enclosure made from solid MDF should contain a softwood backing as a skeleton for mounting support, and to reduce splitting.
  NOTE: A softwood core with MDF laminate, or a soft/hardwood face will be sufficient without a skeleton backing.

Electrical Preparation

Warning:

• Proper grounding is required for your safety, to prevent electrical shock or fire. The refrigerator is provided with the proper grounding for internal electric faults from the factory. This grounding must not be removed or altered.
• Ensure that the converter or DC power supply is grounded properly per manufacturers instruction. Per RVIA the power supply is required to be isolated and grounded with the Coach Chassis
• This refrigerator will accept voltage levels up to 17V DC only. Anything other than this, including any AC power will cause product damage and void the warranty
• The refrigerator requires a power source that can adequately provide 10.5 – 17V DC to function properly. Furrion Recommends Power Center (FCVSWC42A or FCVSWC54A) and Lithium Battery (FB12I10C) to match with.
• The refrigerator should be dedicated to a single branch circuit, and must be fused for 15A minimum.
  NOTE: An internal 15A fuse is provided with the product. This is only intended to protect the internal wiring of the unit. It will not protect the power source and wiring to the product and is not to be used as a substitute. The internal fuse will however allow for a larger rated branch circuit. NOTE: Sharing power with other devices on the same branch circuit may cause transient surges and voltage drops. These interferences may damage or limit functionally of all devices on the branch circuit.
  NOTE: When replacing an absorption refrigerator, the power supplied is usually shared with other powered features in the coach, such as overhead lights. A separate dedicated branch circuit will be preferred to eliminate flickering during compressor operation.
• The maximum input of the appliance is rated for 11A. All wiring must follow RVIA and NEC standards based on the input rating.
• Apply the following wiring guidelines to achieve maximum performance out of the battery reserve.

Dedicated from the Distribution Box/Panel

Direct Connection from Battery

• If additional grounding is desired for external faults to the refrigerator chassis, an external grounding wire can be prepared and attached directly to the terminal block. The terminal block is rated for Maximum 300V at 25A.
• Enter service wire into the cabinet space. It is acceptable to enter through the cabinet floor, sidewall or ceiling. Ensure that the wire is within the ¼ ” space provided to the back of the unit and cabinet.
  NOTE: For replacement of an existing refrigerator, the wire may need to be re-routed into the cabinet if the entryway point is not within the ¼ ” spacing.
• If no sidewall access panel/vent is available to reach the rear wire connection of the appliance, plan for the appropriate wire length to reach outside of the cabinet so the wire connection can be made before installing.
  NOTE: Furrion recommends dropping the 12V feed wire from the upper rear of the cabinet down to the terminal block. Temporarily affix the wires to the upper half of the appliance with tape so that excess wire will droop without risk of rubbing with the appliance chassis and floor during installation.

Drainage Preparation
The cavity condensate drainage is captured in a drain pan integrated with the unit. No external drainage needs to be prepared at this point.

Installing the Refrigerator

Electrical Connection

1. Remove the strain relief and connector cover using a Phillips screwdriver. (Fig. 1)
2. Connect the cables to the correct terminals as shown in Fig. 2. Connect the terminal “+” to the 12V DC positive pole connect the terminal “-” to the 12V DC negative pole.
3. Connect additional chassis grounding to the Terminal block labeled “GND” if desired.
4. Fix the cable with the strain relief and replace the connector cover. (Fig. 3)

Installation without Sidewall Access

1. Slide the unit into the enclosure. Care should be taken to avoid rubbing the chassis and wire together during installation. (Fig. 4)
   NOTE: Elevating the wire and use of wire sheathing/wire loom will help protect the wire.
2. Unscrew the air vent fixing screws and remove the air vent. (Fig. 5)
3. Center the fridge in the opening to ensure the trim covers all front gaps in the cabinet.
4. Affix the refrigerator into the enclosure on both the top and bottom. (Fig. 6 and Fig. 7)
   NOTE: Use the appropriate wood style screw to bite into the softwood portion of the cabinet framing.
   NOTE: Do not mount the top or bottom first, and push the free end of the refrigerator cavity to square up in the enclosure. Doing so will mis-align door the latches. If the cabinet is out of square, shim appropriately.
5. Reinstall the air vent and tighten the screws. (Fig. 8)

Installation with Sidewall Access

NOTE: Follow the below steps where a sidewall vent or access panel is available, such as when replacing an existing gas absorption refrigerator.

1. Place refrigerator in the enclosure, described in Fig. 4 from the “Installation without Sidewall Access” section. Disregard any electrical connections at this step
2. Remove the existing sidewall vent or open the sidewall access panel, for access to the rear of the appliance.
3. Confirm location of the wire and that no interference with the refrigerator chassis frame will cause an abrasion or pinch on the wire. Relocate the wire if necessary, it should be within the ¼” space between the back of the unit and cabinet. Refer to “Electrical Preparation” of this manual for further detail.
4. Inspect fit of the refrigerator to the cabinet. Push tight into position.
   NOTE: Sealing foam may be interfering in the rear and will require removal of contact locations with a knife.
5. Affix the refrigerator to the cabinet following steps 2 – 5 in section “Installation without Sidewall Access”.
6. If applicable, cap and seal the gas line with a ⅜” flange fitting plug. Turn the gas on and check for any gas leaks using a non corrosive liquid leak detection solution.
7. Make the electrical connection as described in “Electrical Connection” section.
8. If necessary re-seal any openings that were revealed from cutting away the foam in step 3 that may prevent moisture leakage/propagation.
   NOTE: Foaming/sealing gaps along the perimeter of the refrigerator sides and bottom is not necessary.

Reversing the Door Swing (Optional)

Your refrigerator is ordered as either a left or right open swing from the factory, you may change the door swing direction as required.

1. Disassemble the freezer door by removing the Hinge A fixing screws. (Fig. 9) Remove the Hole Plastic Cover Plugs from the left side of the refrigerator and set aside for future use.
2. Disassemble the Refrigerator Door by removing the Hinge B and Hinge C fixing screws. (Fig. 10)
3. Reverse the parts of Freezer Door Lock Cover, Metal Bracket, Plastic Bushing, Freezer Door Lock, Lock Fixing Block to the opposite side respectively. (Fig. 11)
4. Remove the Refrigerator Door Lock Cover (right) and save it for future use. Change Refrigerator Door Lock and Lock Fixing Blocks to the opposite side. Install the left side Refrigerator Door Lock Cover, provided as an accessory with the unit, where the door lock was. (Fig. 12)
5. Reverse the Metal Bracket and Plastic Bushing on the bottom of Refrigerator Door. (Fig. 13)
6. Unscrew the Door Latch Bracket fixing screws and change it to the opposite side. (Fig. 14)
7. Fix the Hinge A at the bottom left. Reinstall the Refrigerator Door and fix the Hinge B to the left side of the middle beam. (Fig. 15)
8. Reinstall the Freezer Door and then fix the Hinge C at the top left. (Fig. 16)

Door swing change is complete, now check for proper alignment. Feel for any binding, or misalignment of the door, and make certain the latch is catching and releasing correctly. Slight adjustments can be made by loosening and adjusting the hinges if needed.
NOTE: The instructions above are for changing the door open direction from the left to the right. By reversing the above steps, you can change the door open direction from right to left.

Operation

The appliance has a low-voltage shut-off function, intended to protect your RV battery’s from excessive drain.
NOTE: This function controls compressor operation only, a small electric current is still used for the LED cavity light and low-voltage monitoring system. Once voltage is increased, the system will automatically begin normal operation.

Temperature Control

Proper food storage temperatures is important to reduce the risk of foodborne illness bacteria.

The temperature control knob is located in the fresh food compartment of the refrigerator. It is designed to set the temperature from cold to coldest or turn the refrigeration system off.
The recommended operating temperatures for proper food storage is as follows:

Turn the thermostat to max when first starting the refrigerator and after putting large quantities of food in. After a few hours turn it down between mid and max position to reach the recommended operating temperature setting. This will ensure the cabinet is thoroughly chilled before food is placed into the refrigerator. Placing large amounts of food may require additional cooling time to bring the temperature down. Several conditions may require adjustment of the temperature dial, use the following chart as a guideline.

NOTE: If power is lost during operation, the refrigerator will automatically resume operation after 3 to 5 minutes. The temperature knob does not need to be adjusted or cycled to restart the refrigerator.

Off Grid Usage

• Where grid power is not available, the “OFF GRID” setting can be used to maximize battery life.
• During travel, where a tow vehicle will provide constant battery charging, it is recommended to operate the refrigerator at a normal temperature setting dial (refer to “Temperature Control” section). Once you have arrived and are dependent on your battery reserve, rotate the knob to the “OFF GRID” setting of the dial.
• It is recommended to store meat and dairy products towards the back and middle shelf of your refrigerator. Utilize the other space of the refrigerator for beverages, condiments, and produce.

NOTE: Operation time of refrigerator in “OFF GRID” mode depends on, but not limited to, factors such as; ambient temperature, battery capacity, condition of battery, thermostat setting, food qty, and frequency of door openings. Reference the below chart to adjust operation time based on ambient temperature.

Extreme Temperature Usage

The normal operating temperature for this appliance is 50°F (10°C) to 109.4°F (43°C).
The refrigerator can be used in ambient temperatures between 109.4°F (43°C) and 125.6°F (52°C), but expect reduced cooling performance. If the ambient temperature exceeds 125.6°F (52°C), allow the inside of the coach to cool down before turning on. If the ambient temperature is below 50°F (10°C), the dial control may need to be turned towards max to operate the refrigerator. The freezer can be operated with ambient temperatures below 32°F (0°C), but expect the refrigerator to be frozen. Furrion recommends increasing the ambient temperatures above 50°F (10°C) for best results.

Adjusting the Shelf (Optional)

To avoid the possibility of child entrapment, do not remove any shelf from the refrigerator. Shelving is intended to deter children from play in the compartment area.

The refrigerator and freezer shelves are fixed in the compartments from the factory. Shelving adjustment is possible with the following Instruction:
NOTE: The instructions will walk through the freezer compartment shelving, but apply to all shelving.

To adjust the freezer compartment shelf position:

1. Open the compartment door. (Fig. 17)
2. Lever the shelf fixing screw cover using a sharp tool. (Fig. 18)
3. Loosen the fixing screw using a Phillips screwdriver. (Fig. 19)
4. Repeat steps 2 and 3 to loosen the shelf fixing screw on the other side. Pull to remove the shelf out from its original position. (Fig. 20)
5. Slide the shelf into an appropriate position and fix with screw. (Fig. 21)

Storage Lock

Utilize the Storage Lock, provided in the accessories package with the unit, to prop the door open during extended storage. This will provide air flow throughout to reduce moisture and odors.

NOTE: It is not recommended to leave the Storage Lock in position during traveling, vibration may shake the latch loose.

1. Press the Storage Lock onto the lock bracket directly to install it.
2. Press both sides of the Storage Lock as per the arrows shown in Fig. 22 and pull to remove the Storage Lock.
3. Close the doors so that the door latch engages with the storage lock.

Transportation

Your refrigerator is designed to operate during normal transportation of your coach. Please refer to the following guidelines to assist during transportation.

• During long trips, leave your refrigerator off until 3 hours before your destination arrival. This will help reduce any moisture/ice accumulation and accidental battery discharging.
• Avoid traveling with food in the cavity. Wait until you have arrived to your destination and remove any remaining food before departing.
• Never transport with the Storage lock in place.
• Turn refrigerator to “OFF” if climbing/crawling any off-road grades. Compressor oil should resettle within 2 hours.

Energy Saving Tips

• When possible, place your coach or refrigeration in a position to avoid direct sun.
• Cool down the hot food to normal temperature before putting them into the refrigerator.
• Be sure to wrap foods properly, and wipe containers dry before placing them in the refrigerator. This could prevent frost buildup inside the refrigerator.
• Organize and label the food to reduce door openings and long time searches.

Extended Storage

Any time the unit is not to be in-use, it is considered “extended storage”. Follow the below steps to properly prepare the unit for storage:

1. Remove all food and turn the dial to off.
2. Let any accumulated ice thaw, and dry out with a towel.
3. Disconnect power(either via main disconnect switch, and turning the converter off or fuse).
4. Remove charcoal filter to preserve charcoal activation, replace with a new filter every season or after three months of active use.
5. Install door Storage Lock. See the “Storage Lock” section about how to install the Storage Lock.

Cleaning and Maintenance

Cleaning Refrigerator Interior
It is recommended to clean the interior as needed due to spills and other cleaning needs, or each time a new charcoal filter is replaced.

Cleaning your Door Panels
Keep the refrigerator outside clean. Wipe with a clean cloth lightly dampened with kitchen appliance wax or mild liquid dish detergent. Dry and polish with a clean, soft cloth.
Do not wipe the refrigerator with a soiled dish cloth or wet towel. These may leave a residue that can erode the paint. Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch and weaken the paint finish.

Battery Maintenance

Your refrigerator has an automatic shut-off switch, should the voltage drop below 9.6V at the terminal connection. This is to help prevent permanent damage to your batteries.
NOTE: Once voltage is re-established the refrigerator will begin working automatically per the setting of the dial. When possible maintain the float voltage listed on your battery. Solar is a good way to maintain battery voltage if
a local power source is not available. Contact Furrion for further questions or options on Solar.

Replacing the Interior LED

Electric Shock Hazard
Remove power to the refrigerator by turning off the converter, disconnecting the battery main, or pulling the fuse. Failure to do so may result in electrical shock or personal injury.

Before removing the LED, turn the refrigerator temperature control to the OFF position. Replace the old LED with a new LED of the same wattage and size. Contact Furrion or Furrion authorized dealer to purchase a genuine Furrion replacement LED (C-FCR10DCDTA-S01).

1. Unscrew the three screws (Fig. 23)
2. Press the cover backwards toward the rear of the unit and open it. (Fig. 24)
3. Remove the clip and two screws to replace the old LED with a new LED. Fix the clip and tighten the screws. Then reinstall the cover. (Fig. 25)

Replacing the Charcoal Filter

It is recommended to replace the charcoal filter every three months of active use. Contact Furrion or Furrion authorized dealer to purchase the replacement charcoal filter (C-FCR10DCDTA-B01).
Replace the charcoal filter by pulling it out from the refrigerator as shown in Fig. 26 and replace with a new one.

Door Panels

Furrion offers high gloss black, matte black, stainless steel and black stainless steel colors of refrigerator door panel. Contact Furrion or Furrion authorized dealer to purchase the replacement door panel.

Refrigerator Door Panel

When replacing the refrigerator door panel, the following dimensions should be met:

1. Pull out the Side Cover. (Fig. 27)
2. Slide out the Refrigerator Door Panel and replace with a new one. (Fig. 28)

Replacing Freezer Door Panel

When replacing the freezer door panel, the following dimensions should be met:

1. Hold the right of the Top Cover and lift upward to remove.
2. Take off the Side Cover. Slide out the Freezer Door Panel and replace with a new one. Reinstall the Top Cover and Side Cover. (Fig. 30)

Circuit Diagram

Specifications

Troubleshooting

A qualified professional is required for any servicing of the compressor drive board and the control board, otherwise it will void the product warranty. If you encounter a problem similar to what is mentioned in the following table, try the suggested solution below to see if you can solve the problem before calling service.

FURRION 3-Zone Entertainment System with DVD Specifications

Product

• DV120-BL
  
• DV1220-SS
  
  

Product Content

• CLIMATESMART™
  
• VIBRATIONSMART™
  
• CLIMATESMART™
  
• SIGNALSMART™
  
• APP CONTROL
  
• FRONT ACCESS HDMI
  
• AUXILIARY IN
  
• USB INTERFACE
  
• SUBWOOFER OUT
  
• 3-ZONE SPEAKER CONTROL
  
• AUDIO CONTROL WHEEL
  
• WORKS WITH UNIMOTE
  

Dimensions

DV1220-SS

DV1220-BL

Specifications

Packaging Information

Master Carton

* Note: “√”=Equipped “●” = Not available

Support

USA Innovation Center & Institute of Technology: 52567 Independence Ct. Elkhart, IN 46514
Customer Service & Technical Support:

Email: support@furrion.com
Tel : (888) 354 5792
Website: www.furrion.com

Furrion® and the Furrion logo are trademarks licensed for use by Furrion Ltd. and registered in the U.S. and other countries. ©2007-2019 Furrion Ltd.

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Furrion Ltd. is under license. Other trademarks and trade names are those of their respective owners.

The N-Mark is a trademark or registered trademark of NFC Forum, Inc. in the United States and in other countries. DVD Video is a trademark of DVD Format / Logo Licensing Corporation.

FACT11MA-PS                                  FACT11MA-BL

Features

• Compatible with all size of rooftop units
• Maximize air flow louver to two outlets
• Compatible with both ducted and non-ducted RVs
• Detachable filters for easy cleaning
• Stylish and slim design
• Available in black and white options

Specifications

Packaging Information

Container Load Information

* Note: “√”=Equipped

USA Innovation Center & Institute of Technology: 52567 Independence Ct. Elkhart, IN 46514
Customer Service & Technical Support:
Email: support@furrion.com
Tel : (888) 354 5792
Web: www.furrion.com

GAS OVEN WITH LED KNOBS
FSRD22LA

	CLIMATESMART
	VIBRATIONSMART
	AUTO SAFETY SHUT OFF
	OVEN CAPACITY
	LED DIGITAL THERMOSTAT
	PULSE IGNITER
	UP TO 60 MINS.
	OVEN LIGHT
	LED KNOB
	COOLING FAN
	BTU
	TRIPLE-LAYER GLASS DOOR

FSRD22LA | GAS OVEN WITH LED KNOBS

Specifications

Dimensions

Packaging Information

Container Load Information

USA Innovation Center & Institute of Technology: 52567 Independence Ct. Elkhart, IN 46514
Customer Service & Technical Support:
Email: support@furrion.com
Tel : (888) 354 5792
www.furrion.com
Furrion and the Furrion logo are trademarks licensed for use by Furrion Ltd. and registered in the U.S. and other countries. ©2007-2018 Furrion Ltd.

 Outdoor TV Owner's Manual

Engineered for Outdoor Viewing.

A stunning picture comes as standard thanks to the 65″ 4K Ultra-High Definition screen. Get a perfect picture in fully-shaded outdoor environments while the premium 350-nit LCD screen with auto-brightness control adjusts the light levels for optimum viewing. Outdoor safe, it can withstand all conditions when exposed to the elements.

Key Benefits

Made for Outdoor: With a weatherproof housing and IP54 rating, the TV is engineered to withstand the harsh e acts of UV rays, dirt, insects, humidity, and to cope with extreme temperature variations (-27.4 ºF to 140 ºF).

Incredible Picture: The 4K Ultra-High Definition screen delivers crystal clear images and ultra-bright picture at 4 times the resolution of full HD.

Auto-Brightness Control: The ambient light sensor with auto-brightness control automatically changes the screen’s lighting levels adjusting to bright and dark conditions for optimal viewing at all times.

Main Features

Power

Input Power — 100-240V AC
Power Plug — US

Panel Specifications

Screen Size — 65″
Resolution — 3840 x 2160
Refresh Rate — 60Hz
Contrast Ratio — 4000:1
View Angle — 178 degree/178 degree
Response Time — 6.5ms
Brightness — 350nits

Broadcasting System

Analog — NTSC
Digital — ATSC

Audio

Mono/Stereo/Dual (MTS/SAP) — NICAM/A2
Audio Output (Watts – THD 10%) —  8W X 2
Speaker System —  1 Way 2 Speakers Stereo
Dolby Digital Decoder — ✓
Surround System — ✓
Bass/Treble/Balance — ✓
Auto Volume Leveler — ✓
Sound Mode — 4 Modes

Special Features

Child Lock/ V-Chip — ✓
Closed Caption — ✓
Smart link (HDMI CEC) — ✓
ARC Audio out — ✓
1080P Source Input — ✓
4K Source Input — ✓

Convenience Features

Language — English/French/Spanish
Channel Add/Delete — ✓
Auto Tuning/Programming — ✓
Sleep Timer — ✓
On/Off Timer — ✓
Favorite Channel Programming — ✓
Auto/Manual Clock — ✓
Auto Off (Sleep) — ✓

AV Inputs & Outputs

# of HDMI Inputs — 3
# of D-Sub(VGA) Inputs — 1
# of Audio LR Outputs — 1
# of PC Audio Inputs — 1
# of Antenna (RF) Inputs — 1
# of Composite AV Inputs — 1
# of Component (Ybor) Inputs — 1
# of USB Inputs — 1
# of Coaxial Audio Outputs — 1
HDMI Version — 2

Cabinet

Visa Compatible — 400 x 400mm

Dimensions/Weight

Product Size (WXHXD) — 59 x 34.83 x 4.54″ (1498.6 x 884.8 x 115.4mm)
Individual Packaging Dimensions (WXHXD) — 66.02 x 42.13 x 8.43″ (1677 x 1070 x 214mm)
Net Weight (lbs./kg) — 77.16 / 35
Gross Weight (lbs./kg) —  93.03 / 42.20

55″ Furrion Aurora™ Full Shade 4K LED Outdoor TV

Engineered for Outdoor Viewing.

A stunning picture comes as standard thanks to the 55″ 4K Ultra-High Definition screen. Get a perfect picture in fully-shaded outdoor environments while the premium 350-nit LCD screen with auto-brightness control adjusts the light levels for optimum viewing. Outdoor safe, it can withstand all conditions when exposed to the elements.

Key Benefits

Made for Outdoor: With a weatherproof housing and IP54 rating, the TV is engineered to withstand the harsh e acts of UV rays, dirt, insects, humidity, and to cope with extreme temperature variations (-27.4 ºF to 140 ºF).
Incredible Picture: The 4K Ultra-High Definition screen delivers crystal clear images and ultra-bright picture at 4 times the resolution of full HD.
Auto-Brightness Control: The ambient light sensor with auto-brightness control automatically changes the screen’s lighting levels adjusting to bright and dark conditions for optimal viewing at all times.

Main Features

Power

Input Power — 100-240V AC
Power Plug — US

Panel Specifications

Screen Size — 55″
Resolution — 3840 x 2160
Refresh Rate — 60Hz
Contrast Ratio — 4000:1
View Angle — 178 degree/178 degree
Response Time — 6.5ms
Brightness — 350nits

Broadcasting System

Analog — NTSC
Digital — ATSC

Audio

Mono/Stereo/Dual (MTS/SAP) — NICAM/A2
Audio Output (Watts – THD 10%) —  8W X 2
Speaker System — 1 Way 2 Speakers Stereo
Dolby Digital Decoder — ✓
Surround System — ✓
Bass/Treble/Balance — ✓
Auto Volume Leveler — ✓
Sound Mode — 4 Modes

Special Features

Child Lock/ V-Chip — ✓
Closed Caption — ✓
Smart link (HDMI CEC) — ✓
ARC Audio out — ✓
1080P Source Input — ✓
4K Source Input — ✓

Convenience Features

Language — English/French/Spanish
Channel Add/Delete — ✓
Auto Tuning/Programming — ✓
Sleep Timer — ✓
On/Off Timer — ✓
Favorite Channel Programming — ✓
Auto/Manual Clock — ✓
Auto Off (Sleep) — ✓

AV Inputs & Outputs

# of HDMI Inputs — 3
# of D-Sub(VGA) Inputs — 1
# of Audio LR Outputs — 1
# of PC Audio Inputs — 1
# of Antenna (RF) Inputs — 1
# of Composite AV Inputs — 1
# of Component (YPBPR) Inputs — 1
# of USB Inputs — 1
# of Coaxial Audio Outputs — 1
HDMI Version — 2

Cabinet

Visa Compatible — 400 x 400mm

Dimensions/Weight

Product Size (WXHXD) — 50.25 x 29.76 x 4.17″ (1276.4 x 755.8 x 105.9mm)
Individual Packaging Dimensions (WXHXD) — 57.20”x 8.43” x 35.83” (1453x 214 x 910 mm)
Net Weight (lbs./kg) — 60.63lbs / 27.50kg
Gross Weight (lbs./kg) — 74.96lbs / 34kg

49″ Furrion Aurora™ Full Shade 4K LED Outdoor TV

Engineered for Outdoor Viewing.

A stunning picture comes as standard thanks to the 49″ 4K Ultra-High Definition screen. Get a perfect picture in fully-shaded outdoor environments while the premium 350-nit LCD screen with auto-brightness control adjusts the light levels for optimum viewing. Outdoor safe, it can withstand all conditions when exposed to the elements.

Key Benefits

Made for Outdoor: With a weatherproof housing and IP54 rating, the TV is engineered to withstand the harsh e acts of UV rays, dirt, insects, humidity, and to cope with extreme temperature variations (-27.4 ºF to 140 ºF).
Incredible Picture: The 4K Ultra-High Definition screen delivers crystal clear images and ultra-bright picture at 4 times the resolution of full HD.
Auto-Brightness Control: The ambient light sensor with auto-brightness control automatically changes the screen’s lighting levels adjusting to bright and dark conditions for optimal viewing at all times.

Main Features

Power

Input Power — 100-240V AC
Power Plug — US

Panel Specifications

Screen Size — 49″
Resolution — 3840 x 2160
Refresh Rate — 60Hz
Contrast Ratio — 4000:1
View Angle — 178 degree/178 degree
Response Time — 6.5ms
Brightness — 350nits

Broadcasting System

Analog — NTSC
Digital — ATSC

Audio

Mono/Stereo/Dual (MTS/SAP) — NICAM/A2
Audio Output (Watts – THD 10%) —  8W X 2
Speaker System — 1 Way 2 Speakers Stereo
Dolby Digital Decoder — ✓
Surround System — ✓
Bass/Treble/Balance — ✓
Auto Volume Leveler — ✓
Sound Mode — 4 Modes

Special Features

Child Lock/ V-Chip — ✓
Closed Caption — ✓
Smart link (HDMI CEC) — ✓
ARC Audio out — ✓
1080P Source Input — ✓
4K Source Input — ✓

Convenience Features

Language — English/French/Spanish
Channel Add/Delete — ✓
Auto Tuning/Programming — ✓
Sleep Timer — ✓
On/Off Timer — ✓
Favorite Channel Programming — ✓
Auto/Manual Clock — ✓
Auto Off (Sleep) — ✓

AV Inputs & Outputs

# of HDMI Inputs — 3
# of D-Sub(VGA) Inputs — 1
# of Audio LR Outputs — 1
# of PC Audio Inputs — 1
# of Antenna (RF) Inputs — 1
# of Composite AV Inputs — 1
# of Component (YPBPR) Inputs — 1
# of USB Inputs — 1
# of Coaxial Audio Outputs — 1
HDMI Version — 2

Cabinet

Visa Compatible — 200 X 400mm

Dimensions/Weight

Product Size (WXHXD) — 44.74 x 26.79 x 4.15″ (1136.4 x 680.4 x 105.5mm)
Individual Packaging Dimensions (WXHXD) — 50.39 x 8.46″ x 32.09″ (1280 x 215 x 815 mm)
Net Weight (lbs./kg) — 50.71lbs / 23kg
Gross Weight (lbs./kg) — 59.75lbs / 27.10kg

43″ Furrion Aurora™ Full Shade 4K LED Outdoor TV

Engineered for Outdoor Viewing.
A stunning picture comes as standard thanks to the 43″ 4K Ultra-High Definition screen. Get a perfect picture in fully-shaded outdoor environments while the premium 350-nit LCD screen with auto-brightness control adjusts the light levels for optimum viewing. Outdoor safe, it can withstand all conditions when exposed to the elements.

Key Benefits

Made for Outdoor: With a weatherproof housing and IP54 rating, the TV is engineered to withstand the harsh e acts of UV rays, dirt, insects, humidity, and to cope with extreme temperature variations (-27.4 ºF to 140 ºF).
Incredible Picture: The 4K Ultra-High Definition screen delivers crystal clear images and ultra-bright picture at 4 times the resolution of full HD.
Auto-Brightness Control: The ambient light sensor with auto-brightness control automatically changes the screen’s lighting levels adjusting to bright and dark conditions for optimal viewing at all times.

Main Features

Power

Input Power — 100-240V AC
Power Plug — US

Panel Specifications

Screen Size — 43″
Resolution — 3840 x 2160
Refresh Rate — 60Hz
Contrast Ratio — 4000:1
View Angle — 178 degree/178 degree
Response Time — 6.5ms
Brightness — 350nits

Broadcasting System

Analog — NTSC
Digital — ATSC

Audio

Mono/Stereo/Dual (MTS/SAP) — NICAM/A2
Audio Output (Watts – THD 10%) —  8W X 2
Speaker System — 1 Way 2 Speakers Stereo
Dolby Digital Decoder — ✓
Surround System — ✓
Bass/Treble/Balance — ✓
Auto Volume Leveler — ✓
Sound Mode — 4 Modes

Special Features

Child Lock/ V-Chip — ✓
Closed Caption — ✓
Smart link (HDMI CEC) — ✓
ARC Audio out — ✓
1080P Source Input — ✓
4K Source Input — ✓

Convenience Features

Language — English/French/Spanish
Channel Add/Delete — ✓
Auto Tuning/Programming — ✓
Sleep Timer — ✓
On/Off Timer — ✓
Favorite Channel Programming — ✓
Auto/Manual Clock — ✓
Auto Off (Sleep) — ✓

AV Inputs & Outputs

# of HDMI Inputs — 3
# of D-Sub(VGA) Inputs — 1
# of Audio LR Outputs — 1
# of PC Audio Inputs — 1
# of Antenna (RF) Inputs — 1
# of Composite AV Inputs — 1
# of Component (YPBPR) Inputs — 1
# of USB Inputs — 1
# of Coaxial Audio Outputs — 1
HDMI Version — 2

Cabinet

Visa Compatible — 200 X 200mm

Dimensions/Weight

Product Size (WXHXD) — 39.90 x 23.81 x 4.12″ (1013.4 x 604.9 x 104.7mm)
Individual Packaging Dimensions (WXHXD) — 44.69″ x 7.68″ x 28.74″ (1135 x 195 x 730 mm)
Net Weight (lbs./kg) — 37.92lbs / 17.20kg
Gross Weight (lbs./kg) —  49.60lbs / 22.50kg

Customer Service & Technical Support: Email: support@furrion.com Tel : (888) 354 5792 www.furrion.com Furrion® and the Furrion logo are trademarks licensed for use by Furrion Ltd. and registered in the U.S. and other countries. © 2007-2019 Furrion Ltd.

FDUF43CBR

28” LED HD TV
FEHS28E8A

• Climatesmart – designed and tested for extreme climates
• Custom Furrion upgraded speakers and amplifier
• Furrion smart link communication
• Added LED strips for extra brightness and picture quality

FEHS28E8A | 28” LED HD TV

* Note: “√”=Equipped

USA Innovation Center & Institute of Technology: 52567 Independence Ct. Elkhart, IN 46514
Customer Service & Technical Support: Email: support@furrion.com Tel : (888) 354 5792 www.furrion.com
Furrion and the Furrion logo are trademarks licensed for use by Furrion Ltd. and registered in the U.S. and other countries. © 2007-2018 Furrion Ltd.

ft. 4-Door Refrigerator Instructions

• AC high efficiency compression refrigerator
• Tempered glass and wooden shelves
• Convenient and quick built-in RV style installation
• Individually controlled temperature for wine and beer

FCR14ACBQA | 14 cu. ft. 4-DOOR REFRIGERATOR

Specifications

Validity Capacity                                              14 cu. ft.
Door Type                                                       Four doors & side by side
Storage Compartments                                    Wine & storage & freezer
Cooling Type                                                   Compression
Rated Voltage                                                  AC 115V
Rated Frequency                                             60Hz
Rated Current                                                  1.5A
Power Consumption                                        1.268 kWh/24h
Fridge Temperature Range                               0ºC to 10ºC (32ºF to 50ºF)
Freezer Temperature Range                             < -17.8ºC ( 0ºF)
Wine Storage Temperature Range                    2.8ºC to 16ºC (37.0ºF to 60.8ºF)
Refrigerant/Charge                                          R134a/200g
Noise                                                               <45dB/(A)
Width Working Temperature                           16ºC to 43ºC (60.8ºF to 109.4ºF)
Control Type                                                   Mechanical control
Defrost                                                            Manual defrost
Certification                                                     CSA
Application                                                       Bulit-in type for RV

Special Features

USA Innovation Center & Institute of Technology: 52567 Independence Ct. Elkhart, IN 46514
Customer Service & Technical Support: Email: support@furrion.com Tel : (888) 354 5792 www.furrion.com
Furrion and the Furrion logo are trademarks licensed for use by Furrion Ltd. and registered in the U.S. and other countries. ©2007-2018 Furrion Ltd.

Specifications

Dimensions

Door Panel Dimensions

USA Innovation Center & Institute of Technology:

52567 Independence Ct. Elkhart, IN 46514

Customer Service & Technical Support:

Email: support@furrion.com
Tel : (888) 354 5792
www.furrion.com

Furrion and the Furrion logo are trademarks licensed for use by Furrion Ltd. and registered in the U.S. and other countries. © 2007-2019 Furrion Ltd.