BT-S2 Pro Bluetooth Helmet Intercom

User Manual

Package Contents

Product Descriptions

The Inter Phone is a Bluetooth Headset designed for the motorcycle rider and passenger who wish to have clear and reliable wireless communica­tions while riding. This headset is compatible with Bluetooth cellular phones and can be suited to any sort of helmet for motorcyclists.

1. Phone Button
2. Volume –
3. Volume+
4. Power/intercom Button
5. Cable Input Interface
6. Charger and Headset Socket
7. LED Indicator

Main Features

1. Bluetooth intercom and mobile phone can be connected within a range of 10 meters.
   Bike-to-bike intercom for rider & passenger or two separate bikes.
   Up to 800-1000 meters.
   Up to 10 hours talk time when connected to cell phone.
   Up to 8 hours talk time when using the intercom feature.
   Up to 300 hours standby.
2. Answer/reject call.
3. Receive a cell phone call automatically
4. Support audio transfer.
5. Support the last number redialing.
6. FM Radio function.
7. Enjoy the cell phone music through A2DP or connect GPS.
8. Control cell phone music through AVRCP: forward, backward, play, pause.
9. Automatic switching among bluetooth cell phone, intercom, stereo music.
10. With DSP echo cancellation and noise suppression technology, crystal clear voice quality is guaranteed in a high speed.
11. Button panel is water-proof and sun-proof, while the design is durable.
12. Audio cable to connect MP3, GPS, walkie-talkie and so on.

Using the Headset Clip Mount with Fastening Clamp

1. Using the provided screw driver, loosen the Clips’ screws enough to allow the Clip to slide onto either side of the Helmets’ shell.
2. Make sure you put the clip under the helmets padding.
3. Adjust the Clip until you find the best location for your helmet.
4. Tighten the screws to hold the clip firmly in place.

Mounting the Inter Phone

1. Take your Inter Phone Headset and slide it down into the slots in the Headset Clip Mount. Make sure that it’s perfectly fitted and locked into place by trying to extract it, pulling upwards.

2. Now you need to attach the speaker and microphone arm to the inside of the helmet. Take the Velcro pad which the speaker will attach to, and test for the best position to fix it. The Velcro Pad should be fixed at the height of your ear in the helmets ear pocket. You will need to put the helmet on a few times to find the optimum position to apply the pad. When the correct positioning is found, remove the protective strip and apply the Velcro Pad.

3. Next, take the Ear Speaker and attach it to the Velcro Pad. Run the Microphone Arm down along down to where your mouth will be. As the Microphone Arm is flexible, you can adjust it so it sits in the optimum position in front of your mouth. Some helmets have removable padding; if yours does, it is recommended to run the speaker and microphone under the padding.

4. Taking care to match the pins up, connect the Headset Plug to the Headset Socket. The plug can only be inserted in one position.

5. Secure the cord of the Headset Plug inside the helmet. Tuck any extra wire into the helmet. Ensure that only few centimeters of the cord comes out. You have successfully mounted the Inter Phone

Note: Another choice for mounting the Inter Phone
You can directly use the Velcro(with 3M) to mount the lnterphone on the edge of helmet. See the following pictures.

Quick Removal of the Inter Phone

Remove the BT-52 Prolnter Phone by pushing down the lock as shown and then take out the Inter Phone Module in an upward motion

Charging The Headset

Before using this device, Please charge the headset with USB charging cable. Please ensure that the battery is fully recharged when you first time use it.
We have provided you with the ability to charge the system via the USB port of your computer.
The charging cable has a small USB plug for the headset and the large USB plug for the computer or AC adapter; please observe to correct orientation of the USB plug and socket before inserting

1. Insert the USB plug of the charging cable, into the USB small jack of the headset; you can either charging by computer or AC adapter.
2. While charging, the red LED on the headset module will illuminate, when the charging is finished, the red LED will extinguish. A normal charge from a low battery will take about 4 hours.

Note: if you do not use the headset for a month or more, to protect the Poly-Li battery, please charge the headset at least every month. (The fault damaged by wrong charging will be not guaranteed).

Turning the Unit on into Standby Mode
Press and hold the power/intercom button at the end of the unit. After 3 sec you will hear a “Di” and the blue LED will begin to flash. Let go of the button and the unit is now in standby mode.

Turning off the Unit
Press the power /intercom button for 5 seconds until you hear a “Di” tone and the lights extinguish.
Note: When turn off the unit, please don’t loosen the power/intercom button when hear “dudu”tone. If so, the Bluetooth memory will be cleared away.

To Pair to Your Bluetooth Enabled Mobile Phone

1. Turn on the unit into standby mode (only need blue light flashing).
2. Open the Bluetooth function on your mobile phone.
3. Bluetooth on your phone will search the device until you see BT-S2 Pro.
4. Click “BT-S2 Pro” on your phone, you will hear “DiDi” tone when pair successfully.

Phone Controls

To answer a call – Short press the Phone button once.
Auto receive call – the unit will automatically answer the call after 8-16 seconds of ringing.
To reject a call – Press the Phone button and hold until you hear a “Du” (around 2 seconds).
To end a call – Whilst call is active short press the Phone button once Last number redial – When in standby mode. Press and hold the Phone button for 2 seconds until you hear a “Du”.
To go to a phone call during an intercom call – Press and hold the Phone button for 2 seconds until you hear a “Du”.

Note: Depending on the phone some or all of these functions may not work, or operate differently.

Music Controls
Play / Pause – Short press phone button once
Next Track- Turn the “+” button and let go
Previous Track- Turn the”- ” button and let go
To Adjust the Volume
Long press”+”button to increase and long pess”-” button to decrease. This function is also fit for intercom/music/FM radio

To Pair 3 Devices in Intercom Mode

1. Follow the above procedure for each combination of the three units.(A-B, B-C, A-C).
2. Ensure the third unit is switched off when pairing the other two devices. For example: When A is paired with B, C is turned off. When B is paired with C, A is turned off. When A is paired with C, B is turned off.
3. Only 1 connection can be live at a time. Please follow the above steps to pair A-B, B-C,A-C.After pairing A and C successfully, press A’s power button once, that means A and C exit the intercom mode. At this time, A, B, and C are in standby mode, B acts as a bridge. And then press A’s power button again, A Enter the intercom mode with B. Press A’s power button twice, A Enter the intercom mode with C. Press C’s power button once, Band C enter the intercom mode.
4. From Standby press the power/intercom button 1 time for one of the pairings to be called, or 2 times for the other pairing to be called.
5. The pairing for 1 or 2 presses will depend on the sequence in which you paired the 3 helmets, but once paired the relevant pairings will maintain the number.
6. i.e. A will press the power/intercom button 1 time to call C and 2 times to call B. B will press the button 1 time to call C and 2 times to call A. C will press the button 1 time to call A and 2 times to call B.

About the second pairing
When you unintentionally turn off the intercom or need to use for a second time, You can do as following :

1. Turn on the two intercoms at the same time, then will see the blue lights flashing.
2. Please wait 5-6 seconds after the blue lights flashing.
3. Then press the”power button” of any intercom, after 3-6 seconds, blue lights on both devices flashing at the same time and remain alight. for about 2-3 seconds, indicating successful pairing.

To Reset the Pairing Memory

1. If you have problems pairing, then it is best to reset the pairing memory
2. Turn on the relevant unit into standby mode. Press the power/intercom button for 3-5 seconds till a “dudu” can be heard.
3. Let go of the button when the tone is heard.(The unit will turn off)
4. Restart, the memory will be erased. (Repair again)

To Start FM Radion
After turn the unit on, Press Phone button for 2 Times(till hear “du” tone), let go of the button, FM rad ion will start.

Short press:”+” or ,,_,, button you can adjust the channel.
When FM radio start, Press Phone button for 2 Times, FM will end up (stop).
Note: In order to make FM radio the best effect, you should pay attention to the following instruction:

1. The line of earphone is unfolded.
2. Try to listen to the FM radio outside or near the window.
3. Because of the frequency problem, FM function may not be used in Japan.

To Use Audio Cable
Audio cable can insert cable input interface, it can connect MP3, GPS, Mobile phone and so on.
Pis: Walkie-talkie Audio cable also can insert cable input interface, it can connect walkie-talkie, so it can intercom for a group of people at the same time. (Walkie-talkie Audio cable need to purchase separate).
Cable adapter is different, according to different model of walkie-talkie.

FAQs:

Is my unit still under warranty?

All Fodsports units come with a 1-year warranty, starting from the date of purchase. Please keep your proof of purchase in order to reclaim your warranty.
Create a record of ownership in case of loss or theft.
REGISTER NOW
Your first point of warranty service is your dealer

Why are my speakers volume low?

A: Please note that both the volume of the intercom or the volume of listening to music can be adjusted with the volume +- button, if you think the intercom volume is too low, you can press “+” button to increase the intercom volume.

Why are my two speakers or one side speaker unavailable/no sound?

Please note that both the volume of the intercom or the volume of listening to music can be adjusted with the spin button, if you think the intercom volume is too low, you canTurn clockwise to increase the intercom volume.

How long will it take to receive the items we buy?

For All Fodsports Intercom FAQs Visit: https://manuals.plus/fodsports/fodsports-intercom-faq

Tech Specification

fodsports.com

Fodsports FX6 Group Talk Helmet Intercom

USER MANUAL

BLUETOOTH HEADSET

1. Packing List

2. Function Introduction

3. Installation Step

3.1 Fixed by clamp

3.2 Fixed by VELCRO sticker

4. Disassembly of the Device

5. Product Introduction

6. Button Operation Introduction

6.1 On/Off Button

Turn on: ( When the headset is off, press and hold ii for 3 seconds. There is a “Welcome to FODSPORTS Bluetooth Communication System” sound prompt, and the blue light will be on for 1 second.)

Turn off: ( When the headset is on, press and hold it for 5 seconds. There is a “Power Off’ sound prompt, and the red light will be on for 1 second.)

Pairing: ( When the headset is off, press and hold it for 6 seconds. There is a “Pairing” sound prompt, and blue and red lights flash alternately.)

Clear the pairing device: ( When the headset is on, keep pressing the button for another 3 seconds after turn it off. After “power off’ sound prompt, the red light quickly flashes 3 times and a “toot” sound prompt can be heard.)

Start the Bluetooth Intercom: (When paired, press once on the button, you will hear an “Intercom Connected” sound prompt When the connection is successful, then press again to disconnect the intercom, press again to reconnect.)

Note: If B pair with A & C successively, B need to press the button once to initiate intercom with C, and press twice to intercom with A.

End the Bluetooth Intercom: ( Shortly press the button and intercom closes after a “Intercom disconnected” sound prompt.)

6.2 Multi-function Button

Pairing: ( When the headset is on, press and hold it for 6 seconds. There is a “Pairing” sound prompt, blue and red lights flash alternately.)

Answering a call: ( When there is coming call, click it once to pick up or take no action, the headset will pick it up automatically, you will hear “Dong Dong” sound prompt.)

Rejection of call: ( If there is a call, press and hold it 2 seconds to reject, you will hear “Dong Dong” sound prompt. )

Disconnect headset temporarily & answer by phone: ( During a call, press and hold it for 2 seconds. There is a “Dong” sound prompt, and the red light flash every other second.)

End a call: ( Click it once on call will end it, there is a “Dong” sound prompt.)

Voice dialing: ( If you are not on a call, click it twice and there is a “Voice Dial” sound prompt.) NOTE: Please make sure that your phone supports voice command and the functions are turned on.

Music Play/Pause: ( When connected, click it once.)

Switch between Bluetooth and FM: ( When the headset is on, triple-click it and there is “Bluetooth mode” or “FM mode” sound prompt.)

*Turn on/off FM: When device is on, short press Multi-function Button 3 times to Switch on / off FM function.

6.3 Knob

Turn up the volume: ( On a call , intercom, playing music or FM, turn the knob clockwise and hold it to increase volume until ii reaches the level you want . A “tool” prompt will be heard when it reaches Max volume.)

Turn down the volume: ( On a call , intercom, playing music or FM, turn the knob counter clockwise and hold ii to decrease volume until ii reaches the level you want. A “toot” prompt will be heard when it reaches Min volume.)

Play the next: ( When playing music or FM, turn the knob clockwise . )

Play the previous: ( When playing music or FM, turn the knob counter clockwise .)

7. Bluetooth Status Indication and Prompt

Power on status: ( If Bluetooth is connected, there is a “Bluetooth connected” sound prompt ,the blue indicator light flashes once every 6 seconds; if Bluetooth is not connected, there is a “Bluetooth disconnected” sound prompt , the blue indicator light flashes twice every 6 seconds.)

Low battery alarm: ( The “Battery Low” sound is prompted every 60 seconds when turn on, red light will keep flashing.)

Charging status: ( Red light is on when charging and off when fully charged.)

Battery status sound prompt when powered on: ( If the battery is full, the “Battery

Full” sound is prompted. If the battery is low, the “Battery Low” sound is prompted.)

8. Pairing Methods

8.1 Two ways for FX6 to enter pairing status

8.1.1 Mode 1 When the headset is off, press and hold On/Off Button for 6 seconds. There is a “Pairing” sound prompt, blue and red lights flash alternately.

8.1.2 Mode 2: When the headset is on, press and hold Multi-function Button for 6 seconds. There is a “Pairing” sound prompt, and blue and red lights flash alternately.

8.2 Pairing with the Non-Fodsports FOB Bluetooth device

Step 1: Place the FX6 and the device within a visible range of 1 meter.

Step 2: Set the Non-FX6 Bluetooth device into paring status.

Step 3: Follow step (8.1.2), FX6 enters pairing status.

Step 4: Short press FX6 on/off button to search the device, the Intercom connected” sound prompt means the 2 items are successfully paired.

Note 1: In step 4, the intercom connection must be initiated by FX6.

Note 2: When intercom, press FX6 on/off button to disconnect the intercom, then press again to reconnect.

8.3 Pairing with Mobile, GPS and MP3

Step 1: Place the “FODSPORTS FX6” and the device within a visible range of I meter.

Step 2: Follow step (8.1.1), “FODSPORTS FX6′ enters pairing status

Step 3: Tum on the device Bluetooth, search “FODSPORTS FX6” and connect. The connected’ sound prompt means the connection is successful.

8.4 Pairing between two FX6

Step 1: Ensure both FX6 are off and within 1 meter visible range.

Step 2: Follow step (8.1.1), both FX6 are in pairing status.

Step 3: Short press the multi-function button or on/ off button on ether FX6 to search the other one, you will hear “intercom connected” when successfully pried.

NOTE: In the pairing status, short press multi-function button on either FX6 to search, can be used for connection between 2 FX6 only. For other non-FX6 deviceu have to press the on/ off button.

8.5 Group Intercom Settings

Note: For group intercom. the first and last FX6 CAN NOT be paired.

Step 1 : Clear the matching record between A and F
Press and hold the on/off buttons of A and F for 6 seconds until you hear sound prompt “power off”, then hold them for another 3 seconds.

Step 2 : Refer to the matching operations in 8.4 for following operations

1. Pair A and B, turn off B after successfully paried;
2. Pair B and C, turn off C after successfully paried;
3. Pair C and D, turn off D after successfully paried;
4. Pair D and E, turn off E after successfully paried;
5. Pair E and F.

Step 3: Connect A, B, C, D, E and Fin series

1. For D, press the on/off button to connect with E;
2. For C, press the on/off button to connect with D;
3. For B, press the on/off button to connect with C;
4. For A, press the on/off button to connect with B.

* E and Fare connected completed after the Step 2 , Now A, B, C, D, E and Fare all matched successfully, you can enter group intercom.

Note: During the 6 people group intercom, if D receives a call, D will be disconnected temporarily from the group. A, Band C form a group, E and F form a group.

After D finished call, D will be reconnected into the group intercom automatically and the 6 people group intercom resumes.

8.6 Simultaneous connection of multiple devices

Note: Please DO NOT pair FX6 with mobile phone before you pair it with Bluetooth headset, otherwise, it may cause intercom communication error. It won’t happen if FX6 is not connected with phone.

9. Priority of Functions

Level 1: Phone call & Intercom by introduced adapter.
Level 2: Intercom introduced by Two-way radio cable.
Level 3: Bluetooth Intercom
Level 4: FM & Music

10. Specifications

• Bluetooth Version: 5.0
• Operating Range: Up to 1000 meters
• Standby Time: Up to 200 hours
• Operating Time: Up to 10 hours
• Charging Time: Approximately 2.5 hours
• Charging Interface: Micro USB Android universal plug
• Battery Type: Rechargeable Li-Polymer battery
• Power Supply: 5V-0.5A
• Operating Temperature: 14F-131F (-10 C-55 C
• Storage Temperature: -4F-140F (-20°C-60°C)

* The actual time may vary from the phone type and usage.

* The working distance will be deviated for the influence of environment and climate

11. Matters Need Attention

1. The Bluetooth name is “FODSPORTS FX6”.

2. The appropriate storage temperature for this device is between -20 C and 60 C. Please do not store it in environment with too high or too low temperatures, otherwise the service life will be affected.

3. To avoid explosion, please do not expose it to open fire.

4. If you’re not using it for a long time, please keep the device in dry place and charge it regularly (once every 3 months), to preserve battery life.

12. After-Sale Service

For any quality problem or missing accessories, especially pairing problem between 2 or more FX6 headsets, please feel free to contact us at email: [email protected]. We’re always here ready to help, will reply to you in 12 hours.

FAQs:

Why are my two speakers or one side speaker unavailable/no sound?

A: 1. Please check if the headphone cable is inserted in the correct direction, M1-S PLUS is a Type-C interface, with the microphone icon facing you, and then inserting the interface is the correct direction. 2. Please make sure the headphone cable is fully inserted into the interface.

Why is my microphone unavailable/no sound?

The microphone part is detachable and can replace the soft/boom microphone, so please check if this part is inserted tightly.

Why are my speakers volume low?

Different locations of speakers will cause differences in volume, please install the speaker as close to your ears as possible. If the distance is too far, the volume will be reduced. You can use the thickened pad in the package to achieve it.

How Does FX6 Work?

Can FX6 be paired with other brands of Bluetooth intercoms?

Technical Specifications

M1-S Pro Bluetooth Helmet Intercom Headset

Operation Manual

Attention

Thank you for purchasing FODSPORTS M1-S PRO Bluetooth stereo headsets. For best experiences, please read manual before use.

Sound volume warning

Long period or too loud may hurt hearing ability.

Disassemble or modification

The M1-S PRO is precisely made in the factory. Any disassemble or modification may damage the device. Please do not tear any of the safety regulation and serial number sticker from the device, that will void warranty. Please contact us at [email protected] if needed.

Warranty:
In normal use, we offer one year warranty from the date of purchase. Any disassemble, modification, will void warranty.

1. Outlook (e.g. M1-S PRO)

Functions
Switch On: When device is off, press intercom button and function button at samelimefor3 seconds.
Switch Off: When device is on, press intercom button and function button at samelimefor3
Power Detect: When device is on, short press volume”-‘ button and volume”+’ button at same time.
Voice control function {Only If your cellphone is equipped) : Short press function button once.
Switch on external wired device such as speed detector : when device IS on, long press volume•-• button and volume”+’ button at same time for 3 seconds.

Cellphone Function
Answering call: Short press function button once.
Hangup call : After call, short press function once.
Refuse call : After call, short press function button once.
Redial : Short press function button twice.
Volume up : Press volume’,” button while talking.
Volume down : Press volume”-” button while talking.
Switch manual/automatic answering calls : While in standby, press and hold the intercom button and volume ” +” / “-” button at the same time for 3 seconds.

Device Pair Up
Pairing mode : When device is on, long press function button for 5 seconds. Search mode When device is on, long press intercom button for 5 seconds. Remark, pairing mode is for pairing up to other devices like cellphone, gps Search mode is for pairing up with other Ml-S PRO.

Music Function
Play : When device is on, short press volume”+” button twice.
Pause : When music playing, short press volume”+” button twice.
Volume up : When playing music, short press volume”+” button once.
Volume down : When playing music, short press volume”: button once.
Play previous : When playing music, long press volume”+” button for 2 seconds.
Play next : When playing music, long press volume “-” button for 2 seconds.

Intercom Function
Switch intercom on : when device on : short press intercom button once.
Switch off : when talking, short press intercom button once.
Volume up : when talking, short press volume’,” button once.
Volume down : when talking, short press volume”, button once.

Special Function
Update mode : Plug in the Data & power cable, press volume “-” button and function button at same time for 5 seconds.
Memory clear : When device is on, press volume “+” button and function button at same time for 5 seconds.

2. Recharge

For first time use, please recharge the device until red light is off.

1. Use data and power cable plug to the socket, connect to power source.
   Bike usb chargers are not recommended, unsterilized circuit may damage the device.
2. When connecting to power source, red light appears in function button. When recharge complete, red light is off. Complete recharge is about 2 hours.

Low power notification

When power lower than 10%, Red light flash in the function button and voice message will remind power lower than 10%, please recharge immediately.

Power Detect Function

M1-S PRO has power detection function, when device is on, short press volume”-” button and volume”+” button at same time. Recorded voice message will remind
Power over 90%
Power over 50%
Power lower 50%
Power lower than 10% please recharge immediately
Voice control function( only if your cellphone is equipped): short press function button once
Switch on external wired devices such as speed detector … : when device is on, long press volume”-” button and volume”+” button at same time for 3 seconds.

3. On / Off

1. Switch on : long press function and intercom button at same time for
3 seconds. until blue light flash in function button. Voice message says “welcome to the Fodsports bluetooth communication system”.

2. Switch off : When the device is on, long press function and intercom button at same time for 3 seconds, until red light flash in function button. The device will detect power and voice message will says “power off’.

4. Pair Up To Different Devices

M1-S PRO can pair to different Bluetooth devices.

Pairing Mode

Search Mode

It’s search mode, voice message shows “Searching” sound.

5. Pairing With Cellphone

Remark, when pairing complete, please check both cellphone audio and media audio are all chosen, otherwise call or music can’t be processed.

6. Telephone Function

M1-S PRO is set to automaticity answer incoming calls, when incoming calls, beside rings, blue light flashes. Push function button to answer and push function button to hang up.
When talking, press volume”+” button and volume”-” button to adjust volume.

When the device is on, short press function button twice, will redial, blue light flashes.

*Only redial last call out number

7. Voice Command

When your M1-S PRO is paired up with your cellphone, when both device are on, short press function button once, will automatically switch on the voice command function

*Cellphone must be equipped with this function

8. Music Selections Functions

Play/Pause

Play music: When cellphone and M1 -S paired up, when both devices are on, short press volume”+” button twice, will play music.

Pause: When playing music, short press volume”+” button twice, will pause.

Previous

Long press volume”+” button for 2 seconds, will play previous music in your cellphone music list.

Next

Long press volume”-” button for 2 seconds, will play next music stored in your cellphone music list.

9. Wire Connecting

Long press volume”+” button and volume”-” button for 3 seconds.

M1-S PRO equipped with wire connection function in order to connect to devices without bluetooth. As long as the device is connected by 3.5mm aux out, all can transmit voice signal to M1 -S PRO.

When device wire connected by 2.5mm to 3.5mm cable to M1-S PRO, long press volume”+” button and volume”-” button for 3 seconds to switch on the connection.

* When wired mode is switched on, it will keep it on until switch off the M1-S PRO.

10. Operating Scenario 1:

One person use, pair to cellphone + Bluetooth GPS device + Bluetooth speed detector

*After M1-S PRO paired with gps, if don’t switch off gps’s bluetooth, its will interference the pairing when pairing to speed detector. Recommended to switch gps bluetooth off, after pair up to detector, switch the bluetooth back on.

11. Operating scenario 2:

Two persons intercom, and pairing to cellphone + Bluetooth GPS + speed detector or radio

Passenger Procedure:
Step 1: switch rider headset to search mode, passenger headset to pairing mode. When both headset stop red+blue light flashes, they are paired.
Step 2: switch rider headset to pairing mode, cellphone search this M1-S PRO and pair it up.
Step 3: keep riders headset in pairing mode, use bluetooth gps to search rider’s headset and pair it up.
Step 4: use 2.5mm to 3.5mm aux in to connect speed detector or radio to M1 -S PRO, and switch M1-S PRO to Wire Connecting, all audio integrade complete.
Please read STEP 9. For Wire Connecting.

12. Operating Scenario 3:

Two persons intercom, rider using cellphone + Bluetooth GPS passenger using Bluetooth Speed detector

Pairing Procedure
Step 1: switch rider headset to search mode, passenger’s headset switch to pairing mode, when red and blue light stop flash, intercom pairing complete. At same time instantly switch on intercom.
Step 2: Set rider headset to pairing mode, use cellphone to search rider’s headset to complete pair up.
Step 3: set rider’s headset to pairing mode, use bluetooth gps to search rider’s headset and complete.
Step 4: set passenger’s headset to pairing mode, use Bluetooth speed detector to search passenger headset and complete pair up.

13. Multiple Intercom

Multiple intercom pairing procedure

*Numbers of device which the headset can be paired 8 x M1-S PRO (A, B, C D}, multiple intercom connections, the connection will occupy channels, thus only unit A can connect to the other two Bluetooth devices, the others B, C, D can only connect to one Bluetooth device.

M1-S PRO equipped multiple intercom function, support 8 units talk same time,but recommended 4-6 units,pairing procedure as follow.

Step 1: switch on both A and B unit, long press A unit intercom button to search mode, Then long press unit B function button to pairing mode. When blue light on both intercoms, pairing complete.(You should press the intercom button on B unit to end the talking if you need to pair with more than 2 units.in order to new pairing later)
Now A and B unit pairing complete.

Step 2: When B C units on power on status. long press unit B intercom button to search mode, Then long press unit C function button to pairing mode. When blue light on both units, pairing complete.(You should press intercom button on B units if you need 3 units talk same time, then 3 units will light on blue same lime. Or you should press intercom button on C unit to end the talking if you need to pair with more than 3 units)
Three unit pairing complete.

Step 3: When C D units on power on status, Long press unit C intercom button, then long press unit D function button. When blue light on both units, pairing complete.(You should press intercom button on B C units if you need 4 units talk same lime, then 4 units will light on blue same time. Or you need to press intercom on D unit to end the talking if you need to pair with more than 4 units) Pis repeat above steps if you need to pair with 5 or 6 or 7 or 8 units.
Four units pairing complete.

*Interruption
In multiple intercom mode, if there is an incoming call caused one of unit away from the connection. After call, will reconnected automatically. If interruption is caused by distance or bad signal. Please press intercom button to reconnect.

Multiple intercom reconnect procedure

M1-S PRO will remember paired units. But after switch off and want to reconnect again, please follow the procedure.

Step 1: switching off all four units and all bluetooth device connected to the headset.
Step 2: switch on C and D unit, press C unit intercom button to connect to D unit.
Step 3: switch on B unit, press B unit intercom button to connect to C and D unit.
Step 4: switch on A unit, press A unit intercom button to connect to B, C and D unit. After all four unit reconnected, switch on original connected bluetooth devices.

14. Q&A

Q1 : No sounds from one or two side speaker.
A1 : Check device plug, needs to firmly connected.

Q2 : Can it be recharged from bike USB charger while riding?
A2.1 : Not recommended, unstablized power source will cause damage on internal circuit, may cause unable to recharge/can’t fully charged/can’t switch on.

A2.2 : Power bank is a good choice.

Q3 : When using radio, not transmission or continuous transmission.
A3 : Pis check whether plug the 2.5mm pin deeply enough. this pin built in waterproof parts, It is easily misunderstand it have been pluged well because of a little resistance.

Q4 : New device can’t switch on.
A4 : Recharged at least 30mins before use.

FAQs:

Frequently Asked Questions

Why are my two speakers or one side speaker unavailable/no sound?

A: 1. Please check if the headphone cable is inserted in the correct direction.
2. Please make sure the headphone cable is fully inserted into the interface.

 Why is my microphone unavailable/no sound?

The microphone part is detachable and can replace the soft/boom microphone, so please check if this part is inserted tightly.
2. Please check if the headphone cable is inserted in the correct direction.

 Why are my speakers volume low?

Different locations of speakers will cause differences in volume, please install the speaker as close to your ears as possible. If the distance is too far, the volume will be reduced. You can use the thickened pad in the package to achieve it.

 Why is the volume of the intercom really low?

Please note that both the volume of the intercom or the volume of listening to music can be adjusted with the volume +- button, if you think the intercom volume is too low, you can press “+” button to increase the intercom volume.

Technical Specification

Operation Manual

HELMET BLUETOOTH INTERCOM

Attention：

Thank you for purchasing FODSPORTS FX8 helmet bluetooth intercom.For best use experiences,please read manual before use.

Content In Package

Thanks For Purchasing FODSPORTS FX8 helmet Bluetooth intercom, Please Check All Items Before Installation:

1. 1x FX8
2. 1x Headphone&Mic Kits
3. 1x Operation Manual
4. 1xSoft Microphone
5. 1x Usb Cable
6. 1x Metal Clip
7. 2x Eva rubber
8. 2x 3M Glue Velcro
9. 1x Hard Tube Microphone
10. 4x Velcro
11. 1x 2.5mm to 3.5mm

Installation

Fix the headphone & Mic Kits on the right position, adjust the speaker and mic, then hide the speaker cable.

1. Press
   Insert the main unit: press to the button of kits, main unit locked and installation completed.

1. Slide up
2. Press
   Take away the main unit:by press the button and slide it up,disassemble compeleted.

Plug the microphone cable. (Antennas can be turned on or hidden as needed) Remark: Mic should be close enough to mouth, and speaker near to ear. please use sponge if the speaker postion is too deep.

1. Operation

1.1 Outlook / Function

1. LED Indicator
2. Previous
3. Next
4. LED Indicator
5. Function(Volume+/-)
6. Intercom
7. Headphone & Mic Kits
8. Aux In
9. Charge / Data
10. Reset

Switch On / OFF

Switch On: When device is off, press Intercom + Function at the same time for 3 seconds, Voice message will also say Welcome to FODSPORTS Bluetooth Communication System.

Switch Off: When device is on, press Intercom + Function at the same time for 3 seconds. Voice message will also say Power off.

*For first time use, please recharge the device until the red light is off.

Cellphone

Answering Call: Short press Function once.
Hangup Call: After call, short press Function once.
Refuse Call: Long press Function button for 2sec.
Redial: Short press Function button twice.
Volume Up: Rotate the Function button forward while talking.
Volume Down: Rotate Function button Backward while talking.
Manual/Auto Switch: Long press Intercom ,Previous and Next at the same time for 3 sec. when Standby.

Power Detect & Notification Function

Low Power Notification: When power lower than 10%, red light flash in the function button and voice message will remind power lower than 10%,please recharge immediately.
Power Detect Function: FX8 has power detect function, when device is on, short press Previous and Next button at the same time, recorded voice message will tell you:

Power over 90%
Power over 50%
Power lower than 50%
Power lower than 10% please recharge immediately

Music Function

Play: When Standby, short press Function button once.
Pause: When music is playing, short press Function button once.
Volume Up: Rotate the Function button forward.
Volume Down: Rotate the Function button Backward.
Play Previous: When music playing, short press Previous button once.

Play Next: When music playing, short press Next button once.

FM Function

FM ON: When FM is off, Long press Next button for 3 sec.
FM OFF: When FM is on, Long press Next button for 3 sec.
Volume Up: Rotate the Function button forward.
Volume Down: Rotate the Function button Backward.
Search Desk: When FM is on, short press Previous/Next button once.

Memory Clear

Memory Clear: When device is on, press Function and Previous button at the same time for 5 seconds. Then FX8 will clear the pairing memory with other devices.

Intercom Function

Switch Intercom On: When device on, short press Intercom button once.

Switch Intercom Off: When talking, short press Intercom button once.

Volume Up: When talking, Rotate the Function button forward.
Volume Down: When talking, Rotate the Function button Backward.

Voice Command

When your FX8 is paired up with cellphone, short press Previous button twice, will automatically switch on the voice command function (only for iOS).

*Cellphone must equipped with this function.*

2. Device Pairing

2.1 Pair Up to Bluetooth Devices
2.1.1 Pairing Mode

When device is on. Long press Function button to enter Pairing Mode, red and blue lights flash quickly, voice message says pairing. pairing mode for connection to Bluetooth devices such as mobile phones and Bluetooth GPS.

2.1.2 Search Mode

When device is on. Long press Intercom button to enter Search Mode , red and blue lights flash slowly.Search mode only use for intercom function connection between FX8 devices.

2.2 Pairing With Cellphone
STEP-1.

When device is on, long press Function button, red and blue light flash quickly, entering pairing mode.
STEP-2.

Switch cellphone Bluetooth, choose FODSPORTS FX8,the pairing is complete. Voice message will also say Device Connected.

Remark: when pairing complete, please check both cellphone audio and media audio are all chosen, otherwise call or music can not be processed .

2.3 Wire Connecting

Any device with 3.5mm connector can transmit voice signal to FX8.
When device wire connected by 2.5mm to 3.5mm cable to FX8,Complete the wired sound source input. Press the [Previous] and [Next] buttons for 3 seconds to turn on or turn off the wired audio input.

*When wired mode is switched on, it will stay on until you switch off the FX8.

3.Group Intercom Mode Pairing

3.1 Operating Scenario 1:One person use, pair to cellphone + Bluetooth GPS device + Bluetooth speed detector.

STEP-1.

At first of all , pair up GPS and cellphone

STEP-2.

Pair up FX8 with GPS, after paired, please switch off the Bluetooth function in GPS

STEP-3.

Lastly, pair up FX8 with speed detector, after paired, switch on GPS Bluetooth function

*FX8 paired with GPS, if don’t switch off the GPS Bluetooth function, it’s will interference the pairing when pairing to speed detector. Recommended to switch GPS Bluetooth off, after pair up to speed detector, switch the Bluetooth back on.

3.2 Operating Scenario 2:Two person intercom, and pairing to cellphone + Bluetooth GPS + radio

1. Rider Cellphone
2. Rider Headset A
3. GPS
4. Radio
5. Passenger Headset B

Pairing Procedure:

STEP-1. Switch A to search mode (details to 2.1.2), B to pairing mode(details to 2.1.1) .when both headset flash blue lights only, they are paired.

STEP-2. Switch A to pairing mode(details to 2.1.1 ),cellphone search A and pair it up.

STEP-3. Keep A in pairing mode(details to 2.1.1 ),use Bluetooth GPS to search A and pair it up.

STEP-4. Use 2.5mm to 3.5mm AUX in cable to connect radio to FX8, and switch FX8 to wire connecting (details to 2.3 ),all audio inter-grade are completed.

*Switch on intercom , both rider and passenger can hear audio from GPS , speed detector or radio . if rider gets an incoming call , device will cut off the intercom .when rider’s call is finished, device will reconnect automatically

3.3 Operating Scenario 3: Two person intercom, rider using cellphone + Bluetooth GPS,passenger use Bluetooth speed detector.

Pairing Procedure:

1. Rider Headset A
2. Passenger Headset B
3. GPS
4. Cellphone
5. Speed Detector

STEP-1. Switch A to search mode (details to 2.1.2) B to pairing mode (details to 2.1.1).when both headset flash blue lights only, they are paired.

STEP-2. Switch A to pairing mode (details to 2.1.1),cellphone search A and pair it up.

STEP-3. Keep A in pairing mode(details to 2.1.1),use Bluetooth GPS to search A and pair it up.

STEP-4. Set B to pairing mode(details to 2.1.1),use Bluetooth speed detector to search B and pair up.

*When both headsets are switched off, and rider or passenger want to reconnect, please press rider’s intercom button to reconnect and will be able to share all audio source again.

3.4 Multiple Intercom

Multiple Intercom Pairing Procedure

1. Search Mode(Flash Slowly)
2. Paring Mode(Flash Quickly)
3. Search Mode(Flash Slowly)
4. Paring Mode(Flash Quickly)
5. Search Mode(Flash Slowly)
6. Paring Mode(Flash Quickly)

*Numbers of device which the headset can be paired 4 x FX8

(A,B,C,D),multiple intercom connections, the connection will occupy channels , thus only unit A can connect to the other two Bluetooth devices, the others(B,C,D) can only connect to one Bluetooth device.

FX8 equipped with multiple intercom function, recommended 4 units(A,B,C,D), pairing procedure as follow:

STEP-1. Switch both A and B units on, A unit to searching mode (details to 2.1.2),B unit to pairing mode(details to 2.1.1) , A and B paired up and LED Indicator flash blue light. At this time, please press the intercom button of B unit to end the intercom, it’s convenient for next pairing.

STEP-2. Switch both B and C units on, B unit to searching mode (details to 2.1.2),C unit to pairing mode(details to 2.1.1), B and C paired up and LED Indicator flash blue light, short press A unit intercom button, then A,B and C units paired up. At this time, please press the intercom button of C unit to end the intercom, it’s convenient for next pairing.

STEP-3. Switch both C and D units on, C unit to searching mode (details to 2.1.2),D unit to pairing mode(details to 2.1.1), C and D paired up and LED Indicator flash blue light, short press B unit intercom button, then A,B,C and D unit paired up.

Repeat the above method to continue pairing more FX8 units

*Interruption
In multiple intercom mode, if there is an incoming call caused one unit away from the connection, after call, will reconnected automatically. If interruption is caused by distance or bad signal, please press intercom button to reconnect.

3.5 Multiple Intercom Reconnect Procedure

FX8 will remember paired units, but after switch off and want to reconnect again, please follow the procedure:

STEP-1. Switch off all 4 units(A,B,C,D) and all Bluetooth devices connected to the headset such as cellphone and GPS.

STEP-2. Switch on C and D unit, press C unit intercom button to connect D unit . STEP3. Switch on B unit, press B unit intercom button to connect C and D unit . STEP4. Switch on A unit, press A unit intercom button to connect B,C and D unit .after all 4 units reconnected, switch on original connected Bluetooth devices.

Reset

*When device is in the state of crash or stuck, Long press [Reset] button 5 second to restart the system.

4. Technical Specifications

Bluetooth Support: HSP,HFP,A2DP,AVRCP, AGHSP
Working hours: 20 hours
Standby time: 300 hours
Charging time: 3 hours
Battery: lithium battery, 900mA , 3.7v
Dimensions: 9.0cm * 4.0cm * 2.5cm
Weight: 53G, 108G(Include Headphone & Mic Kits)
Frequency Range: 2.4G-2.485G
Operating temperature: -20℃-50℃
Certification: CE FCC ROHS BQB TELEC

5. Q & A / Warning

Q1：No sounds from one or two side speaker.
A1：Check device plug, needs to firmly connected.

Q2：Can it be recharged from bike USB charger while riding ?
A2：1.Not recommended, unstable power source will cause damage on internal circuit, may cause unable to recharge/can’t fully charged/can’t switch on. 3. Power bank will be good.

Q3：When using radio, not transmission or continuous transmission.
A3：Check 2.5mm pin, has to insert firmly. The pin equipped with waterproof aprons, user might think its already plugged.

Q4：New device can’t switch on.
A4：Recharged at least 30 minutes before switch use.

Warning

Sound Volume Warning Long period or too loud may hurt hearing ability. Disassemble or Modification
The FX8 is precisely made in factory. Any disassemble or modification may damage the device, please do not tear any of the safety regulation and serial sticker from the device ,that will void the warranty.Please contact us directly if needed.

6. Statement / Warranty

6.1 FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

6.2 Warranty
In normal use, one year warranty from the date of purchase, any disassemble, modification will void warranty.

Warranty Card

Production Date_______________

Purchase Date_________________

Dealer Name__________________

Item No______________________

Customer Name________________

Customer Tel__________________

Customer E-mail_______________

Remark______________________

FAQs:

Why are my two speakers or one side speaker unavailable/no sound?

Please check if the headphone cable is inserted in the correct direction, 2. Please make sure the base is fully inserted into the interface.

Why is my microphone unavailable/no sound?

The microphone part is detachable and can replace the soft/boom microphone, so please check if this part is inserted tightly. 2. Please check if the headphone cable is inserted in the correct direction.

Why are my speakers volume low?

Different locations of speakers will cause differences in volume, please install the speaker as close to your ears as possible. If the distance is too far, the volume will be reduced. You can use the thickened pad in the package to achieve it.

 Why is the volume of the intercom really low?

Please note that both the volume of the intercom or the volume of listening to music can be adjusted with the spin button, if you think the intercom volume is too low, you can Turn clockwise to increase the intercom volume.

Technical Specifications