Everbilt 9235951 Frameless Inset Hing Installation Guide

We appreciate the trust and confidence you have placed in Everbilt through the purchase of this hinge. We Strive to continually create quality Product designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Everbilt!

Safety Information

Please read and understand this manual before installing this product.

CAUTION:  Always be cautious when using power tools.

Warranty

Subject to the terms of this warranty, the Manufacturer warrants to the original consumer purchaser that the product will be free from defects in material and workmanship. If the product does not comply with this warranty, the Manufacturer will repair or replace the product or, at the Manufacturer’s option, refund the purchase price. Repair, replacement, or refund of the original purchase price is your sole remedy under this or any other warranty on the product, whether expressed or implied. For additional details and questions, please contact Everbilt Customer Service at 1-800-305-1726.

Pre-Installation

1. PLANNING INSTALLATION

• Ensure all parts listed in the Package Contents section are included and that you have the listed Tools Required on hand. If any part is missing or damaged, contact customer service.
• When planning your installation, ensure the hinge is oriented in its nal position as shown. This hinge is intended for inset applications on frameless furniture with the doors positioned inside the front of the cabinet.

• When installed successfully, these hinges can open to a maximum of 110°.

2. TOOLS REQUIRED

3. PACKAGE CONTENTS

4. RECOMMENDED NUMBER OF HINGES PER DOOR SIZE

Use this diagram to determine how many hinges you will need for your door. If you are hanging a door with a mirror or a door that is wider, you will need additional hinges.

Installation

1. Pre-Drilling the installation holes

• Use a pencil and ruler to measure and mark the installation locations as this diagram shows.
• Then use a 1-3/8 in. (35 mm) boring bit to drill the door hole 7/8 in. from the edge. Ensure the door hole is a minimum of 1/2 in. (12.8 mm) deep. Do not drill through the door face.

Diagram for Drilling Hinge Cup

2. Installing the hinges to the door

• Insert each hinge cup (A) into the pre-drilled hole in the door and secure using two 5/8” wood screws (C) for each hinge (A).

3. Installing the mounting plates to the cabinet

• Align the mounting plates (B) to the marked position and fasten
  with two screws. (D)
• See installation diagram on next page.

Diagram for mounting plate screw placement

4. Installing the door to the cabinet

• Open the hinges (A) to the fully-extended position.
• Connet the hinge arm (A) to the mounting plates (B) and press the hinge arm (X) down until they snap to the plates.

5. Adjusting the door

Questions, problems, missing parts? Before returning to the store, call Everbilt

Customer Service 8 a.m. – 7 p.m., EST, Monday-Friday, 9 a.m. – 6 p.m., EST, Saturday 1-800-305-1726

HOMEDEPOT.COM

For the most up to date instructions – please visit HomeDepot.com.
Retain this manual for future use.

Everbilt 2-in-1 Utility Pump

Quick Start Guide
2-in-1 Utility Pump
Non-Submersible Transfer Pump
SKU# 1002 921 354 Model/Modelo UTA02510

Read your manual for installation, operation, and safety information. This guide neither supplements nor replaces the Owner’s Manual.

1. Attaching the suction hose to the strainer

Attach the clear suction hose to the suction strainer by pushing the male threaded end into the rubber coupler on the suction strainer. Then, place the strainer in at least 1 in. of water at the lowest point to be pumped. NOTE: Make sure the connection is airtight. An air leak can cause the pump to run dry.

2. Attaching hoses

Open the bottom cover. Thread the other end of the suction hose to the inlet of the pump. Thread a 5/8 in. garden hose (sold separately, 50 ft. max. length) onto the discharge outlet of the pump.
NOTE: Always ensure the washer in the hose bib is not damaged. An airtight seal is necessary for this pump to operate.
NOTE: Make sure the end of the outlet hose is not underwater. If the outlet is underwater, the pump may not work.
NOTE: Do not coil or kink the hose.

3. Priming water

Unscrew the priming plug. Fill water through the priming hole as the picture shows until it overflow. Tighten the priming plug.

4. Operating

To operate, plug the pump into a GFCI outlet. When the water level has been reduced to approximately 1/8 in. you MUST UNPLUG THE PUMP. DO NOT RUN DRY. NOTE: Make sure the suction hose and suction strainer are in the water before plugging in the pump. NOTE: If water is not pumped in 30 seconds, unplug the power cord and check the connection on the two ends of the inlet hose to make sure there are no air leaks. Then, add water into the outlet again and repeat the process.

1. Connecting garden hose
Attach a garden hose with a 3/4 in. garden hose thread (not included) to the pump outlet. NOTE: Be sure a 3/4 in. garden hose thread connector has a rubber gasket to minimize water leaks. NOTE: The larger the inside diameter and the shorter the length of the hose, the less pressure that is lost (or the larger the flow rate).2. Plugging in the pump
Place the pump on a solid base in the flooded area or any place that you would like to remove water. Plug the pump into a 115-volt GFCI power outlet WARNING: Do not allow the plug to fall in the water and do not stand in water while the pump is plugged in. NOTE: Place upright on a solid base.
NOTE: The pump must be standing in at least 1-1/2 in. (38.1 mm) of water before you start it. The shaft seal is water lubricated and may be damaged if the pump runs dry.3. Operating the pump
Allow the pump to run and monitor its progress. Unplug the pump when it has removed water down to approximately 1/2 in. (12.7 mm). Remove the pump and hose from the location when finished pumping. The hose still has water that can drain back through the pump. Remove remaining water with a squeegee, mop, sponge, towel, wet/dry vac, etc. CAUTION: Do not run the pump dry. Operating the pump without water will cause damage to the seals and will cause the pump to fail, thereby voiding the pump’s warranty. CAUTION: This hole is for anti-airlock purposes only. Leakage of air or water is normal and necessary. DO NOT REMOVE OR PLUG THIS HOLE!
For Professional Technical Support call 1-844-241-5521 Para comunicarse a Soporte técnico profesional llame al 1-844-241-5521

Hinge for Frameless Furniture full Overlay Door Mounting

Item # 1002 782 610 Model # 9235961
USE AND CARE GUIDE
EUROPEAN HINGE FOR FRAMELESS FURNITURE ­ FULL OVERLAY DOOR MOUNTING
Questions, problems, missing parts? Before returning to the store, call Everbilt Customer Service
8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday 1-800-305-1726 HOMEDEPOT.COM
THANK YOU We appreciate the trust and confidence you have placed in Everbilt through the purchase
of this hinge. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home
improvement needs. Thank you for choosing Everbilt!

924394100

Safety Information
Please read and understand this manual before installing this product.

CAUTION: Always be cautious when using power tools.

Warranty

Subject to the terms of this warranty, the Manufacturer warrants to the original consumer purchaser that the product will be free from defects in material and workmanship. If the product does not comply with this warranty, the Manufacturer will repair or replace the product or, at the Manufacturer’s option, refund the purchase price. Repair, replacement, or refund of the original purchase price is your sole remedy under this or any other warranty on the product, whether expressed or implied.
For additional details and questions, please contact Everbilt Customer Service at 1-800-305-1726.

Questions, problems, missing parts? Before returning to the store, call Everbilt Customer Service
8 a.m.-6 p.m., EST, Monday-Friday
1-800-305-1726 HOMEDEPOT.COM

Pre-Installation

PLANNING INSTALLATION

Ensure all parts listed in the Package Contents section are included and that you have the listed Tools Required on hand. If any part is missing or damaged, contact customer service.
When planning your installation, ensure the hinge is oriented in its final position as shown. This hinge is intended for full overlay applications on frameless furniture with the doors positioned in front of the cabinet.

When installed successfully, these hinges can open to a maximum of 95°. 90° 95°

TOOLS REQUIRED

#2 Screwdriver

Pencil or Scribe

Ruler (in. and mm)

Drill

1/6 in. Drill bit

35 mm boring

bit (Forstner bit)

Pre-Installation

PACKAGE CONTENTS

RECOMMENDED NUMBER OF HINGES PER DOOR SIZE

Use this diagram to determine how many hinges you will need for your door. If you are hanging a door with a mirror or a door that is wide, you will need additional hinges.

Installation

1 Pre-drilling the installation holes

Use a pencil and tape measure to measure and mark the installation locations as this diagram shows.
Then use a 1/16 in. drill bit to drill the cabinet holes and a 1-3/8 in. (35 mm) boring bit to drill the door hole. Ensure the door hole is no deeper than 15/35 in. (12 mm). Do not drill through either the door face or the cabinet.

2 Installing the hinges to the door

Insert each hinge (A) into the pre-drilled holes in the door and secure using two screws (C) for each hinge (A

Installation

3 Installing the mounting plates to the cabinet

Align the mounting plates (B) to the pre-drilled holes and fasten with two screws (C) for each mounting plate (B).

4 Installing the door to the cabinet

Open the hinges (A) to the fully-extended position.
Slide each hinge arm (A) to the mounting plates (B) and tighten the screw (1) on each plate (B) to secure in place.

5 Adjusting the door

1 Height Adjustment: Loosen the top mounting
screw (1) to adjust the door up or down.

Overlay Adjustment: Turn the adjustment screw (2) to adjust the door overlay.
Depth Adjustment: Turn the eccentric screw (3) to adjust the distance of the doors from the cabinet. Depth Adjustment: Turn the eccentric screw (3) to adjust the distance of the doors from the cabinet.