USER MANUAL

electriQ 9,200 BTU PORTABLE INDUSTRIAL
AIR CONDITIONER
CMAC10M

Thank you for choosing electriQ
Please read this user manual before using this innovative Air Conditioner and keep it safe for future reference.
Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

SAFETY INSTRUCTIONS

Important!

•  Carefully read the instructions before operating the unit
• This appliance is for indoor use only.
•  Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet.
• Installation must be in accordance with the regulations of the country where the unit is used.
•  If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, modified by a qualified electrician.
• This air conditioner has been tested and is safe to use. However, as with any electrical appliance – use it with care.
•  Disconnect the power from the appliance before dismantling, assembling, or cleaning.
• Avoid touching any moving parts of the appliance.
•  Never insert fingers, pencils, or any other objects through the guard.
•  This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities. It is also not intended for use by those with a lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Do not leave children unsupervised with this appliance.
•  Do not clean the unit by spraying it or immersing it in water.
•  Never connect the unit to an electrical outlet using an extension cord. If an outlet is not available, one should be installed by a qualified electrician.
• Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not stretched or exposed to sharp objects/edges.
•  A damaged supply cord should be replaced by the manufacturer or a qualified electrician in order to avoid a hazard.
•  Any service other than a regular cleaning or filter replacement should be performed by an authorized service representative. Failure to comply could result in a voided warranty.
•  Do not use the appliance for any purpose other than its intended use.
•  The air conditioner unit must always be stored and transported upright, otherwise irreparable damage may be caused to the compressor; if in doubt we suggest waiting at least 24 hours before starting the unit.
•  Do not move the air conditioner while it is operating. When operating the castors should be locked in position.
•  Ensure the unit is positioned so that it is on a flat level surface, and does not cause an obstruction to walkways.
• This air conditioner is not designed to be used on boats, or any other type of transportation.
•  Avoid restarting the air conditioning unit unless 3 minutes have passed since being turned off. This prevents damage to the compressor.
•  Never use the mains plug as a switch to start and turn off the air conditioning unit. Use the provided ON/OFF switch located on the control panel.
•  Always place the unit on a dry and stable surface.
• The appliance should not be installed in the laundry or wet rooms.
• The appliance must be placed in a room without sources of ignition (for example open flames, an operating gas appliance, or an operating electric heater).
• R290 refrigerant gas complies with European environmental directives.
• R290 has a low GWP (Global Warming Potential) of 3.
•  The air conditioners contain around 250 g of R290 refrigerant gas.
•  Do not use or store in an unventilated space with an area smaller than 12 m2 per unit.
•  The room must be such as to prevent stagnation of possible leaks of refrigerant gas as
  there could be a danger of fire or explosion should the refrigerant come into contact with electric heaters, stoves, or other sources of ignition.
• Refrigerant gas may be odorless.
• Do not use the product and contact the retailer for advice, if damage has occurred to the unit which may have compromised the refrigerant system.
• Any repairs or maintenance must only be carried out on the unit by a suitably qualified engineer. Before opening and servicing the unit the authorized engineer must be in possession of a copy of the manufacturer’s service manual and must follow the safety information contained within it to ensure all hazards are minimized.
•  The refrigerant system should not be perforated or punctured. Energy Saving and Unit Safety Protection Tips
• Do not cover or restrict the airflow from the air outlet or inlet.
•  For maximum performance, the minimum distance from a wall or objects should be 50cm.
•  Keep the filters clean. Under normal conditions, filters should only need cleaning once every three weeks (approximately). Since the filters remove airborne particles, more frequent cleaning may be necessary, depending on the air quality.
•  For the initial start-up set the fan speed to maximum.
• To protect the unit, we recommend not using the cooling function when the ambient temperature is higher than 45o C or lower than 18o C.

FEATURES

• The CMAC10M is great for Rooms up to 26 m
• 2-speed fan: Balancing quiet operation with performance.
• Simple operation.
• Castors for Enhanced Portability.
• Durable metal casing.

HOSE SPECIFICATIONS

APPLIANCE DIAGRAM

INSTALLATION

COLD AIR OUTLETS

1.  Line up the dimple on the Elbow with the notch on the hose connector on the top of the air conditioner.
2. Rotate anticlockwise until a click can be heard, indicating the elbow has locked into place.
3.  Insert the Cold Air Hose into the Elbow, again lining up the dimple with the notch in the Elbow.
4.  Rotate the pipe anticlockwise to fix it in place.
5.  The pipe can then be extended and pointed in the desired direction.

HOT AIR OUTLET

1. Push the Hot air pipe onto the Hot air outlet on the top of the appliance.
2.  Extend the pipe and route it outside.

NOTES:

• The best form of installation is through a wall duct. By properly venting you expel hot air from your room while efficiently cooling it.

IMPORTANT SAFEGUARDS

If hoses are extended above the permitted length, the unit may malfunction which can invalidate the warranty. The outlet vent must be well ventilated and not obstructed as this will cause the unit to overheat. Keep all the hoses as straight and short as possible and avoid bending the air hose by more than 45 degrees in order to maintain the performance of the unit. Excessive bends in the hose may prevent the unit from expelling the hot air, which can lead to internal damage which would invalidate the warranty. Ensure that sufficient space is left in from the end of the vent pipes (30cm – Cold air, 90cm Hot air)
OPERATION

Turn the control switch to select your desired fan speed between Low and High.
When you have finished, turn the control switch back to the Off position.
The unit can also be used as a dehumidifier by not using the hot air hose. We advise setting the unit with continuous drainage when using it as a dehumidifier.

MULTI PROTECTIVE FUNCTIONS

FROST PROTECTION
If the temperature of the exhaust is too low, the machine will automatically stop operating until
AUTO-DEFROST
The machine has an automatic defrosting function. If during operation the temperature of the internal coils drops too low, the unit will enter auto defrost and the heating symbol will flash on the control panel.
AUTOMATIC THERMAL PROTECTION
To protect the service life of the machine, the machine has automatic thermal protection. If the temper within the unit is outside of the specified range, the compressor and the blower motor will stop operate temperature has risen.

When the water in the internal water tank exceeds the warning level, the machine will stop operating and the water tank full indicator will illuminate. To resume operation empty the internal water tank. After the water is emptied, the machine will automatically return to its original state.on. the appliance will automatically return to normal operation after the temperature of the machine recovers.

COMPRESSOR PROTECTION
To prevent damage to the compressor there is a 3-minute delay start protection function

EMPTYING THE INTERNAL WATER TANK

MANUAL DRAINAGE:
When the internal water tank is full the unit will stop working.
Shut off the unit and unplug. Try not to move the appliance as this may cause the water in the internal tank to spill out. Remove the water tank from the base of the unit and empty it into a sink or drain. Replace the water tank in the unit before plugging back in and restarting the operation.

CONTINUOUS DRAINAGE:
Remove the water tank from the unit, and remove the rubber cap from the end of the drainage spout. Connect the drainage pipe to the spout. Feed the drainage pipe through the hole in the side of the unit from the inside before sliding the water tank back into place. The drain is gravity fed, so can be routed downwards to a suitable drain. Alternatively, the pipe can be attached to an external uplift pump (not supplied) to pump the water uphill to a suitable drainage point.

NOTE: This model has a self-evaporative function, which reduces the need to empty the water tank. If the units are vented correctly most of the water is reused to cool the condenser coils and any excess is evaporated. Please do not use continuous drainage if you intend to use the self-evaporating facility.

CLEANING AND MAINTENANCE

PLEASE TURN OFF THE UNIT AND UNPLUG FROM THE MAINS BEFORE CLEANING OR PERFORMING ANY MAINTENANCE CLEAN THE SURFACE
Clean the surface of the machine with a wet soft cloth. Do not use chemicals, such as benzene, alcohol, gasoline, etc; otherwise, as this may cause damage to the surface and or the internal workings of the machine
AIR FILTER CLEANING
If the filter screen is clogged with dust, the effectiveness of the air conditioner is reduced. The filter screen should be cleaned once every two weeks or as often as necessary in your environment.
END OF SEASON MAINTENANCE

1. Empty the internal water tank.
2.  Turn off the unit and pull out the plug.
3.  Leave for 24 hours to dry out.
4.  Empty the water tank again as a small amount of water may have drained to it..
5. Coil the wire and bind it together, then put it into the accessories space.
6.  Separate the vent pipes and store them, safely.
7.  Cover the unit and keep it in a dry place.

TROUBLESHOOTING

Do not repair or disassemble the air conditioning. The unqualified repair will invalidate the warranty and may lead to failure, causing injuries and property damage. Only use it as directed in this user manual and only perform operations advised here.

If problems not listed in the table occur or recommended solutions do not work, please contact the service center.

APPENDIX

Disposal: Do not dispose of this product as unsorted municipal waste. Collection of such waste must be handled separately as special treatment is necessary. Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participate in civic amenity sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centers.

electriQ UK SUPPORT

www.electriQ.co.uk/support
Please, for your own convenience, make these simple checks before calling the service line. If the unit still fails to operate call the number below, or complete the online form. 0330 390 3061

1. Has the unit been standing upright for at least 2 hours?
2.  Is the unit plugged into the mains?
3. Is the fuse OK?
4. Switch the unit off and wait three minutes to see if the issue is resolved. Restart the unit.
5. Check if the water tank is full.

Office hours: 9 AM – 5 PM Monday to Friday
www.electriQ.co.uk
Unit J6, Lowfields Business Park
Lowfields Way, Elland West Yorkshire, HX5 9DA

TECHNICAL DATA

V20210106

electriQ 12000 BTU Portable Industrial Air Conditioner CMAC12M

SAFETY INSTRUCTIONS

Important! 

• Carefully read the instructions before operating the unit
• This appliance is for indoor use only.
• Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet.
• Installation must be in accordance with regulations of the country where the unit is used.
• If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, modified by a qualified electrician.
• This air conditioner has been tested and is safe to use. However, as with any electrical appliance – use it with care.
• Disconnect the power from the appliance before dismantling, assembling or cleaning.
• Avoid touching any moving parts of the appliance.
• Never insert fingers, pencils or any other objects though the guard.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities. It is also not intended for use by those with a lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Do not leave children unsupervised with this appliance.
• Do not clean the unit by spraying it or immersing it in water.
• Never connect the unit to an electrical outlet using an extension cord. If an outlet is not available, one should be installed by a qualified electrician.
• Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not stretched or exposed to sharp objects/edges.
• A damaged supply cord should be replaced by the manufacturer or a qualified electrician in order to avoid a hazard.
• Any service other than regular cleaning or filter replacement should be performed by an authorised service representative. Failure to comply could result in a voided warranty.
• Do not use the appliance for any purpose other than its intended use.
• The air conditioner unit must always be stored and transported upright, otherwise irreparable damage may be caused to the compressor; if in doubt we suggest waiting at least 24 hours before starting the unit.
• Do not move the air conditioner while it is operating. When operating the castors should be locked in position.
• Ensure the unit is positioned so that it is on a flat level surface, and does not cause an obstruction to walkways.
• This air conditioner is not designed to be used on boats, or any other type of transportation.
• Avoid restarting the air conditioning unit unless 3 minutes have passed since being turned off. This prevents damage to the compressor.
• Never use the mains plug as a switch to start and turn off the air conditioning unit. Use the provided ON/OFF button located on the control panel.
• Always place the unit on a dry and stable surface.
• The appliance should not be installed in laundry or wet rooms.
• The appliance must be placed in a room without sources of ignition (for example: open flames, an operating gas appliance or an operating electric heater).
• R290 refrigerant gas complies with European environmental directives.
• R290 has a low GWP (Global Warming Potential) of 3.
• The air conditioners contain around 300 g of R290 refrigerant gas.
• Do not use or store in an unventilated space with an area smaller than 14.4 m2 per unit.
• The room must be such as to prevent stagnation of possible leaks of refrigerant gas as there could be a danger of fire or explosion should the refrigerant come into contact with electric heaters, stoves or other sources of ignition.
• Refrigerant gas may be odourless.
• Do not use the product and contact the retailer for advice, if damage has occurred to the unit which may have compromised the refrigerant system.
• Any repairs or maintenance must only be carried out on the unit by a suitably qualified engineer. Before opening and servicing the unit the authorised engineer must be in possession of a copy of the manufacturer’s service manual and must follow the safety information contained within it to ensure all hazards are minimized.
• The refrigerant system should not be perforated or punctured.

Energy Saving and Unit Safety Protection Tips 

• Do not cover or restrict the airflow from the air outlet or inlet.
• For maximum performance the minimum distance from a wall or objects should be 50cm.
• Keep the filters clean. Under normal conditions, filters should only need cleaning once every three weeks (approximately). Since the filters remove airborne particles, more frequent cleaning maybe necessary, depending on the air quality.
• For the initial start-up set the fan speed to maximum and the thermostat to 5 degrees lower than the current temperature. After, set the fan switch to low and set the thermostat to your desired setting.
• To protect the unit, we recommend not using the cooling function when the ambient temperature is higher than 45oC or lower than 18oC.

FEATURES

• 3 in 1 Cooling, Fan, Dehumidifier. The CMAC12M is great for Rooms up to 30 m2.
• 2 speed fan: Balancing quiet operation with performance.
• 24 Hours Start / Stop Timer.
• Digital Thermostat.
• Auto-Restart to retain the settings in the event of power failure.
• Castors for Enhanced Portability.
• Durable metal casing.
• Twin cold air ducts allowing distribution of the cold air.

HOSE SPECIFICATIONS

APPLIANCE DIAGRAM

INSTALLATION

COLD AIR OUTLETS

1. Line up the dimple on the Elbow with the notch on the Hose connector on the top of the air conditioner.
2. Rotate anticlockwise until a click can be heard, indicating the elbow has locked into place.
3. Insert the Cold Air Hose into the Elbow, again lining up the dimple with the notch in the Elbow.
4. Rotate the pipe anticlockwise to fix it in place.
5. The pipe can then be extended and pointed in the desired direction.
6. Repeat for the second air outlet.

HOT AIR OUTLET

1. Push the Hot Air Hose onto the Hot air outlet on the top of the appliance.
2. Extend the pipe and route it outside.

NOTES:

• The best form of installation is through a wall duct. By properly venting you expel hot air from your room while efficiently cooling it.
• Your air conditioner should be used without the vent pipe in dry mode. When using dry mode ensure that the water tank is monitored and regularly emptied. Permanent plumbing can be also installed for dry mode or an external uplift water pump can be set up for unattended use.

IMPORTANT SAFEGUARDS
If hoses are extended above the permitted length, the unit may malfunction which can invalidate the warranty. The outlet vent must be well ventilated and not obstructed as this will cause the unit to overheat. Keep the all the hoses as straight and short as possible and avoid bending the air hose by more than 45 degrees in order to maintain the performance of the unit. Excessive bends in the hose may prevent the unit from expelling the hot air, which can lead to internal damage which would invalidate the warranty. Ensure that sufficient space is left in from the end of the vent pipes (30cm – Cold air, 90cm Hot air)

OPERATION

INDICATORS

MULTI PROTECTIVE FUNCTIONS

FROST PROTECTION
In COOL, DRY or AUTO modes, if the temperature of the exhaust is too low, the machine will automatically stop operating until the temperature has risen.

OVERFLOW PROTECTION
When the water in the internal water tank exceeds the warning level, the machine will stop operating and sound an alarm with the LCD display showing “E4”. To resume operation empty the internal water tank. After the water is emptied, the machine will automatically return to the original state.

AUTO-DEFROST
The machine has automatic defrosting function. If during operation the temperature of the internal coils drops too low, the unit will enter auto defrost and the heating symbol will flash on the control panel.

AUTOMATIC THERMAL PROTECTION
To protect the service life of the machine, the machine has automatic thermal protection. If the temperature within the unit is outside of the specified range, the compressor and the lower motor will stop operation. The appliance will automatically return to normal operation after the temperature of the machine recovers.

COMPRESSOR PROTECTION
To prevent damage to the compressor there is a 3 minute delay start protection function.

EMPTYING THE INTERNAL WATER TANK

MANUAL DRAINAGE:
When the internal water tank is full the unit will stop working.
Shut off the unit and unplug. Try not to move the appliance as this may cause the water in the internal tank to spill out. Remove the water tank from the base of the unit and empty into a sink or drain. Replace the water tank in the unit before plugging back in and restarting operation.

CONTINUOUS DRAINAGE:
Remove the water tank from the unit, and remove the rubber cap from the end of the drainage spout. Connect the drainage pipe to the spout. Feed the drainage pipe through the hole in the side of the unit from the inside before sliding the water tank back into place. The drain is gravity fed, so can be routed downwards to a suitable drain. Alternatively the pipe can be attached to an external uplift pump (not supplied) to pump the water uphill to a suitable drainage point.

NOTE: This model has a self-evaporative function, which reduces the need to empty the water tank. If the unit is vented correctly most of the water is reused to cool the condenser coils and any excess is evaporated. Please do not use continuous drainage if you intend to use the self-evaporating facility.

CLEANING AND MAINTENANCE

PLEASE TURN OFF THE UNIT AND UNPLUG FROM THE MAINS BEFORE CLEANING OR PERFORMING ANY MAINTENANCE

CLEAN THE SURFACE
Clean the surface of the machine with a wet soft cloth. Do not use chemicals, such as benzene, alcohol, gasoline, etc; otherwise, as this may cause damage to the surface and or the internal workings of the machine

AIR FILTER CLEANING
If the filter screen is clogged with dust, the effectiveness of the air conditioner is reduced. The filter screen should be cleaned once every two weeks or as often as necessarily in your environment.

END OF SEASON MAINTENANCE

1. Empty the internal water tank.
2. Then switch the unit to low fan mode.
3. Keep the unit in this mode for half day – until the conduit is dried. Doing this helps to keep the inside of the unit dry and prevents mould from developing
4. Turn off the unit and pull out the plug.
5. Empty the water tank again.
6. Coil the wire and bind it together, then put it into the accessories space.
7. Separate the vent pipes and store the, safely.
8. Cover the unit and keep it in a dry place.

TROUBLESHOOTING

Do not repair or disassemble the air conditioning. Unqualified repair will invalidate the warranty and may lead to failure, causing injuries and property damage. Only use it as directed in this user manual and only perform operations advised here.

If problems not listed in the table occur or recommended solutions do not work, please contact the service centre.

APPENDIX
Disposal: Do not dispose this product as unsorted municipal waste. Collection of such waste must be handled separately as special treatment is necessary. Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating civic amenity sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centres.

electriQ UK SUPPORT

www.electriQ.co.uk/support
Please, for your own convenience, make these simple checks before calling the service line. If the unit still fails to operate call the number below, or complete the online form.
0330 390 3061

1. Has the unit been standing upright for at least 2 hours?
2. Is the unit plugged into the mains?
3. Is the fuse OK?
4. Switch the unit off and wait three minutes to see if the issue is resolved. Restart the unit.
5. Check if the water tank is full.

Office hours: 9AM – 5PM Monday to Friday
www.electriQ.co.uk
Unit J6, Lowfields Business Park
Lowfields Way, Elland
West Yorkshire, HX5 9DA

TECHNICAL DATA

electriQ DF12CR/ DF12CP 12 Inch Desk Fan User Manual

SAFETY INSTRUCTIONS

Important!

• Carefully read the instructions before operating the unit
• This appliance is for indoor use only.
• Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet.
•  Installation must be in accordance with regulations of the country where the unit is used.
•  If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, modified by a qualified electrician.
•  This fan has been tested and is safe to use. However, as with any electrical appliance
  •  use it with care.
•  Disconnect the power from the unit before dismantling, assembling or cleaning the unit
•  Avoid touching any moving parts of the appliance.
•  Never insert fingers, pencils or any other objects though the guard
• This appliance can be used by Children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Do not clean the unit by spraying it or immersing it in water.
• Never connect the unit to an electrical outlet using an extension cord. If an outlet is not available, one should be installed by a qualified electrician.
•  Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not stretched or exposed to sharp object/edges.
•  A damaged supply cord should be replaced by the manufacturer or a qualified electrician in order to avoid a hazard.
•  Any service other than regular cleaning should be performed by an authorized
  service representative. Failure to comply could result in a voided warranty.
•  Do not use the appliance for any purpose other than for its intended use.
•  Never use the mains plug as a switch to start and turn off the fan. Use the provided ON/OFF switch located on the control panel.
•  Always place the unit on a dry and stable surface.
• Fans are designed to create rapid air movement, therefore make sure the fan is not placed near curtains or any objects that may be drawn into the fan inlet.
•  The appliance should not be installed in laundry or wet rooms
•  Do not use this unit in environments with flammable and explosive gases.
•  Avoid keeping the unit in direct sunlight for a long period of time.

Energy Saving and Unit Safety Protection Tips

• Do not cover or restrict the airflow. Do not use in dusty environment.
• For maximum performance the minimum distance from a wall or objects should be 50cm.

To reduce the risk of fire or electrical shock, DO NOT USE THIS FAN with any SOLID STATE Speed Control Device or any variable speed controllers.

DIAGRAM

1. Front Guard
2.  Blade
3. Rear Guard Screws
4. Rear Guard
5.  Motor Shaft
6.  Motor
7. Oscillation Control
8. Control Switch
9. Knob
10. Tube
11. Bas
12. Ring
13. Base Locking Screw
14. Blade Screw

INSTALLATION

BODY ASSEMBLY

1.  Unscrew the BASE LOCKING SCREW from the PIPE and remove the RING.
2. Insert the PIPE through the hole in the center of the BASE and twist into position.
3. Secure the PIPE to the BASE with theFASTENER, RING and BASE  LOCKING SCREW, in that order (see picture)
4. Unscrew the LOCKING NUT from the FAN HEAD.
5. Put the FAN HEAD into the PIPE, then use the SCREW to tighten THE FAN HEAD onto the PIPE.

FAN GRILL ASSEMBLY

1. Align the REAR GRILL on the FAN HEAD, then secure in place using the 4 x REAR GRILL SCREWS.
2. Install the BLADE onto the MOTOR SHAFT by tightening the BLADE SCREW.
3.  Centre the FRONT GRILL by aligning the central logo so that it is horizontal and parallel to the floor. The FRONT and REAR GRILLS should be fastened completely by snapping the 5 x GRILL CLIPS into place.
4.  Tighten the GRILL LOCKING SCREW at the bottom of the REAR GRILL.

OPERATION

1. Twist the SWITCH CONTROL to select the desired speed.
2. Push down the OSCILLATION KNOB to start oscillation. Pull it up to stop oscillation.
3.  Loosen the LOCKING NUT slightly to adjust the tilt angle of the fan head, then re-tighten.

MAINTENANCE

ATTENTION: Please shut off the unit and unplug from the mains before cleaning or performing any maintenance.

CLEANING THE SURFACE

1. Clean the grills with a duster or a soft wet cloth.
2. Do not use chemical solvents (such as benzene, alcohol or gasoline) as they may cause irreversible damage. Make sure no water enters the control panel or fan motor
3. Do not run the unit until completely dry.
4. Place the fan in its original box or cover the fan to protect it from dust. Store it in a cool dry place.

TROUBLESHOOTING

Do not repair or disassemble the unit by yourself, unauthorized repair attempts will invalidate the warranty and may cause bodily harm.

TECHNICAL DATA

electriQ UK SUPPORT

www.electriQ.co.uk/support
Call: 0330 390 3061 or complete the online form
Office hours: 9AM – 5PM Monday to Friday
www.electriQ.co.uk
Unit J6, Lowfields Business Park
Lowfields Way, Elland
West Yorkshire, HX5 9DA

Disposal: Do not dispose this product as unsorted municipal waste. Collection of such waste must be handled separately as special treatment is necessary.

Recycling facilities are now available for all customers at which you can deposit  your old electrical products. Customers will be able to take any old electrical equipment to participating civic amenity sites run by their local councils. Please  remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centres.

USER MANUAL

HVSF16B

Thank you for choosing ElectriQ
Please read this user manual before using this air circulator and keep it safe for future reference.
Visit our page www.electrIQ.co.uk for our entire range of Intelligent Electricals

SAFETY INSTRUCTIONS

Important!

• Carefully read the instructions before operating the unit
• This appliance is for indoor use only.
• Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet.
• Installation must be in accordance with regulations of the country where the unit is used.
• If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, modified by a qualified electrician.
• This fan has been tested and is safe to use. However, as with any electrical appliances – use it with care.
• Disconnect power plug from socket before dismantling, assembling or cleaning the unit
• Avoid touching any moving parts of the appliance.
• Never insert fingers, pencils or any other objects though the guard
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities. It is also not intended for use by those with a lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
  Do not leave children unsupervised with this appliance.
• Do not clean the unit by spraying it or immersing it in water.
• Never connect the unit to an electrical outlet using an extension cord. If an outlet is not available, one should be installed by a qualified electrician.
• Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not stretched or exposed to sharp object/edges.
• A damaged supply cord should be replaced by the manufacturer or a qualified electrician in order to avoid a hazard.
• Any service other than regular cleaning should be performed by an authorized service representative. Failure to comply could result in a voided warranty.
• Do not operate the fan unassembled without protective front and rear grilles in position.
• Do not use the appliance for any other purposes than its intended use.
• Never use the mains plug as a switch to start and turn off the fan. Use the provided ON/OFF switch located on the control panel.
• Always place the unit on a dry and stable surface. Do not move or tilt the unit
• High Velocity fans are designed to create rapid air movement, therefore make sure the fan is not placed near curtains or any objects that may be drawn into the fan inlet.
• The appliance should not be installed in laundry or wet rooms
• Do not use this unit in environments with flammable and explosive gases.
• Avoid keeping the unit in direct sunlight for a long period of time

Energy Saving and Unit Safety Protection Tips

• Do not cover or restrict the airflow. Do not use in dusty environment.
• For maximum performance the minimum distance from a wall or objects should be 50cm.

Warning: To reduce the risk of fire or electrical shock, DO NOT USE THIS FAN with any SOLID STATE Speed Control Device or any variable speed controllers.

3

HVSF16B / HVSF20B 16 / 20-Inch High Velocity Cool Air Circulator Stand Fan with 3 Speed Settings

SPECIFICATIONS

• Slim design takes minimal space
• High Speed Motor with 3 Fan Speed Settings
• Adjustable Tilt Head

PARTS LIST

Fan Housing                Mounting Bracket x 2

Bracket Nuts and Bolts x 4             Support Tube

Base

FAN ASSEMBLY

1. Attach the fan housing to the support tube using a mounting bracket at either side, to clamp both pieces into position before securing with the 4 Bracket Bolts and Nuts.
2. Attach the opposite end of the support Tube to the Base using the base bolts through the underside of the Base.

4

OPERATION

1. Set your fan on a level dry surface.
2. Before plugging into the wall outlet adjust the fan head to your desired angle: loosen the mounting screws then tighten them back in position.
3. Plug the power cord into a standard 220~240 V wall outlet.

CONTROL PANEL AND SETTINGS

Twist the control knob from the 0 and select the appropriate speed Low (1) Medium (2) High (3)

INSTALLATION

This unit can easily be moved from one room to another. While moving the unit please note that it must always be kept upright and then placed on an even surface.

• Remove any packaging – keeping the fan in a vertical position.
• Make sure all parts are present and unit is assembled correctly
• Connect the power plug to a working socket, and then press the power button.

5

MAINTENANCE

CLEANING AND STORAGE

ATTENTION: Please shut off the unit and unplug from the mains before cleaning or performing any maintenance.

Cleaning the surface
Clean the grills with a duster or a soft wet cloth.
Do not use chemical solvents (such as benzene, alcohol or gasoline) as they may cause irreversible damage. Make sure no water enters the control panel or fan motor
Do not run the unit until completely dry.
Place the fan in its original box or cover the fan to protect it from dust.
Store it in a cool dry place.

TROUBLESHOOTING

Do not repair or disassemble the unit by yourself, unauthorized repair attempts will invalidate the warranty and may cause bodily harm.

If the above solutions do not resolve the problem please contact the service centre.

6

TECHNICAL DATA:

7

electriQ UK SUPPORT

www.electriQ.co.uk/support
Call: 0330 390 3061 or complete the online form
Office hours: 9AM – 5PM Monday to Friday
www.electriQ.co.uk
Unit J6, Lowfields Business Park
Lowfields Way, Elland
West Yorkshire, HX5 9DA

Disposal: Do not dispose this product as unsorted municipal waste. Collection of such waste must be handled separately as special treatment is necessary.

Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating civic amenity sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centres.

8

electriQ EAPDC150HCST Desktop Air Purifier User Manual

SAFETY INSTRUCTIONS

IMPORTANT

• Carefully read the instructions before operating the unit.
• This appliance is for indoor use only.
• Rating: This unit must be only connected to a 220-240 V / 50 Hz outlet using the supplied power adaptor.
• Installation must be in accordance with regulations of the country where the unit is used.
• If you are in any doubt about the suitability of your electrical supply have it checked and if necessary, modified by a qualified electrician. • Only use with the power adapter provided by the manufacturer.
• This air purifier has been tested and is safe to use. However, as with any electrical appliance – use it with care.
• Disconnect the air purifier from the socket when changing the filters or cleaning the unit.
• Avoid touching any moving parts within the appliance.
• Never insert fingers, pencils or any other objects though the guard.
• This device is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities. It is also not intended for use by those with a lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Do not leave children unsupervised with this device.
• Do not clean the unit by spraying it or immersing it in water. Use a damp cloth only.
• Do not clean with strong chemical agents or other abrasive materials.
• Never connect the unit to an electrical outlet using an extension cord. If a power outlet is not available, one should be installed by a qualified electrician.
• Never operate this appliance if the cord or power adapter is damaged. Ensure the power cord is not stretched or exposed to sharp objects or edges.
• A damaged power supply should be replaced by the manufacturer. Never extend or attempt to change the power supply lead.
• Any service other than regular cleaning or filter replacement should be performed by an authorised service representative. Failure to comply could result in a voided warranty.
• Do not use the appliance for any purpose other than its intended use.
• Avoid removing the power adapter from the socket while the unit is still in operation. This could cause electrical damage.
• Never use the power supply as a switch to start and turn off the air purifier. Use the provided ON/OFF button located on the control panel.
• Always place the unit on a dry and stable surface.
• The use of attachments that have not been approved by the appliance manufacturer is not recommended, as this may result in fire, cause an electric shock and/or cause personal injury.
• Ensure hands are fully dried before touching the plug or appliance.
• The appliance should not be installed in laundry or wet rooms.

KEY FEATURES 

• 3 Stage purification with Pre, HEPA and Activated Carbon Filters.
• Air quality Indicator light around air outlet.
• 360° Air Distribution.
• DC motor for Quiet Operation.
• Touch Controls with Temperature and Humidity Display.
• 3 Fan Speeds.
• Ioniser.

APPLICATIONS

• Personal use in domestic and office space to improve air quality
• Helps smokers to minimise the effects of smoking
• Provides relief for asthma and pollen sufferers
• Great for children’s rooms and small offices

NOTE

This air purifier is not a substitute for proper ventilation or regular vacuum cleaning. It is not to be used instead of a cooker hood while cooking. If the relative humidity is over 60% we recommend using a dehumidifier to reduce the humidity within the room.

INFORMATION ON INDOOR POLLUTANTS

VOC (VOLATILE ORGANIC COMPOUND):

VOCs come from motor vehicle exhausts, gasoline vapour, pollutants such as formaldehyde, ammonia and many other common and chemical solvents such as paints and glues, or can be a by-product of mould growth. VOCs cause irritation to the eyes and or nose as well as causing headaches, nausea and even potential damage to the central nervous system. Pressed wood furniture, newly decorated rooms, paint and cleaning solvents are common sources of VOCs.

MOULD / FUNGUS

These can affect our respiratory system and cause allergic reactions, like a runny nose, eye and throat irritation, headaches, fatigue and aggravation of asthma. Other indoor pollutants include bacteria, viruses, dust mites and pollen.

EMISSIONS FROM ELECTRONIC OFFICE EQUIPMENT

Many studies, including those from EPA and the University of California Berkley, have reported that emissions from office equipment such as computers and printers, include VOCs, ultra-fine particles and ozone. These emissions have been proven to have a negative effect on the health of many people which can be reduced by using an air purifier.

USING HEPA FILTERS , ACTIVATED CARBON FILTERS AND IONISERS 

An effective HEPA filter is absolutely necessary to remove particles, even at a microscopic level; it ensures that the particles are not spread. The ioniser will automatically operate while the unit is running to sterilise the air and reduce bacterial growth.

The antibacterial activated carbon in the EAPDC150HCST is a natural material biosynthesized from walnut shell, the absorption area of activated carbon is very large at up to 300,000 square meters. The activated carbon filter will absorb unpleasant odours and reduce the VOC content in the air.

PRODUCT OVERVIEW

INITIAL SET UP

Turn the purifier upside down then twist the base cover anticlockwise to unlock and remove it from the unit.

Remove the filter from the plastic packaging and reinstall within the unit.

Place the base cover on the air purifier ensuring it is aligned with the arrow on the housing. Twist the base cover clockwise to lock it into position and secure the filters.

OPERATION

LCD DISPLAY 

Displays the rooms temperature and current humidity.

SPEED

Press the SPEED button to cycle between the three fan speeds. The air purifier will always start in low fan speed when turned on.

FAN SPEED INDICATORS

Shows the current fan speed.

SLEEP MODE

Press and hold the SPEED button to enter sleep mode. In sleep mode all lights will be off and the unit will work at the lowest fan speed. Press any button to exit.

AUTO MODE 

In auto mode, the fan speed will automatically change dependant on the air quality. (See table below).

POWER

Press to turn the air purifier on or off. The power button will flash when the filter needs replacing. After replacing the filter press and hold the POWER button to stop the flashing and reset the filter.

Replacement filter cartridges can be purchased using the code: FIL EAPDC150HCST

ENERGY SAVING AND UNIT SAFETY PROTECTION TIPS

• Do not cover or restrict the airflow from the outlet or inlet grills.
• For maximum performance and safety, the minimum distance from a wall or objects should be 20cm. Keep away from other electrical appliances.
• Keep the filters clean. Under normal conditions, filters should only need cleaning once every two weeks (approximately). Since the filters remove airborne particles, more frequent cleaning maybe necessary, depending on the air quality.
• Replace the filters regularly as instructed.

CARE AND MAINTENANCE

Always turn off the unit and unplug from the mains before cleaning or performing any maintenance. If the unit is not to be used for a prolonged period it is advisable to unplug it from the mains. Do not use chemical solvents (such as benzene, alcohol or gasoline) as they may causeir reversible damage to the unit

CLEAN THE EXTERNAL CASE 

Only use tepid water and a mild detergent on a soft cloth. Do not use bleach or abrasives. Do not splash water directly onto the appliance. Avoid wetting the DC power port. Doing so may cause an electrical shock and can lead to deterioration of the electrical insulation, or cause the unit to rust.

CLEAN THE FILTER AND THE FILTER HOLDING AREA

Vacuum the filter gently every 2-3 weeks or more often if used in a dustier environment. Please make sure the filter is not damaged during the process and replace if necessary. Wipe the filter holding area with a dry cloth.

Replacement filter cartridges can be purchased using the code: FIL EAPDC150HCST.

CLEAN THE FILTER COVER AND CLEAN AIR OUTLET

Use water and a mild detergent. Do not use bleach or abrasives. Do not spray water onto or inside the unit. If the clean air outlet grilles are dirty, use a vacuum attachment or soft brush to clean. Clean the filter cover with a vacuum cleaner, if it is heavily soiled remove it from the unit and wash with warm soapy water. It must be dried thoroughly before reinserting it in the unit.

NOTE: Do not assemble the unit before all the parts are completely dry. Any maintenance not described in this user manual must be performed by the service centre.

TECHNICAL DATA

TROUBLESHOOTING

If the troubleshooting section fails to resolve your issue contact the electriQsupport centre for further assistance.

APPENDIX

Disposal: Do not dispose this product as unsorted municipal waste. Collection of such waste must be handled separately as special treatment is necessary.

Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating civic amenity sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your localhousehold waste recycling centres.

electriQ UK SUPPORT

website: www.electriQ.co.uk/support
Please, for your own convenience, make these simple checks before calling the service line. If the unit still fails to operate call the number below, or complete the online form.

1. Is the unit plugged into the mains?
2. Is the fuse OK?
3. Switch the unit off and wait three minutes to see if the issue is resolved.
4. Restart the unit

Phone: 0871 620 1057

Office hours: 9AM – 5PM Monday to Friday

website: www.electriQ.co.uk
Unit J6, Lowfields Business Park Lowfields Way, Elland West Yorkshire, HX5 9DA.

USER MANUAL

EAP300PM2.5HC

Thank you for choosing electriQ
Please read this user manual before using this innovative
Air Purifier and keep it safe for future reference.
Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

SAFETY INSTRUCTIONS

Important!

• Carefully read the instructions before operating the unit.
• This appliance is for indoor use only.
• This unit must only be connected to a 220-240V / 50Hz outlet.
•  Installation must be in accordance with the regulations of the country where the unit is used.
•  If you are in any doubt about the suitability of your electrical supply, have it checked and, if necessary, modified by a qualified electrician.
• This air purifier has been tested and is safe to use. However, as with any electrical appliance – use it with care.
• Disconnect the air purifier from the socket when changing the filters or cleaning the unit.
•  Avoid touching any moving parts within the appliance.
•  Never insert fingers, pencils or any other objects through the guard.
•  This device is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities. It is also not intended for use by those with a lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
•  Do not leave children unsupervised with this device.
•  Do not clean the unit by spraying it or immersing it in water. Use a damp cloth only. Never allow water or vapors to enter the unit.
•  Do not clean with strong chemical agents or other abrasive materials.
• Never connect the unit to an electrical outlet using an extension cord. If a power outlet is not available, one should be installed by a qualified electrician.
•  Never operate this appliance if the cord or power supply is damaged. Ensure the power cord is not stretched or exposed to sharp objects/edges.
•  A damaged power supply should be replaced by the manufacturer. Never extend or attempt to change the power supply lead.
•  Any service other than a regular cleaning or filter replacement should be performed by an authorized service representative. Failure to comply could result in a voided warranty.
•  Do not use the appliance for any purpose other than its intended use.
• Avoid removing the power cord from the socket whilst the unit is still in operation.
  This could cause electrical damage.
• Never use the power supply as a switch to start and turn off the air purifier. Use the provided ON/OFF button located on the control panel.
• Always place the unit on a dry and stable surface.
•  The use of accessory attachments that have not been approved by the appliance manufacturer is not recommended, as this may result in fire, cause an electric shock and/or cause personal injury.
• Ensure hands are fully dried before plugging or unplugging the appliance.
• The appliance should not be installed in the laundry or wet rooms.
• Always ensure the filters are fitted before turning on the appliance.

Energy Saving and Unit Safety Protection Tips

• Do not cover or restrict the airflow from the outlet or inlet grills.
• For maximum performance and safety, the minimum distance from an object should be 20cm. Keep away from other electrical appliances.
• Keep the filters clean. Under normal conditions, filters should only need cleaning once every two weeks (approximately). Since the filters remove airborne particles, more frequent cleaning may be necessary, depending on the air quality.

AIR PURIFIER DIAGRAM

ABOUT YOUR AIR PURIFIER

The EAP300PM2.5HC provides multiple stages of air purification using professional air filtration technologies. This unit features an advanced HEPA and activated carbon filters for improved air filtration.

• The Pre-filter is used for removing large particles like hair and dust.
• Antibacterial HEPA filter to remove 99.9% of airborne particles of 0.25 micrometers or larger.
• Activated carbon filter removes unpleasant odors and absorbs harmful substances such as formaldehyde and benzenes.

The EAP300PM2.5HC also features a PM2.5 air quality sensor and a front-facing display. The display provides information on the air quality, temperature and humidity of the air within the room.

APPLICATIONS:

•  Personal use in domestic and office space to improve air quality
•  Helps smokers to reduce contaminants within the air
•  Can help improve the symptoms of asthma and pollen allergies.
•  Great for children’s rooms and small offices

NOTE: This air purifier is not a substitute for proper ventilation, regular vacuum cleaning or for use in place of a cooker hood whilst cooking. If the relative humidity is above 60% we recommend using a dehumidifier to reduce the humidity.

INFORMATION ON INDOOR POLLUTANTS

VOC (Volatile Organic Compound): VOCs come from motor vehicle exhausts, gasoline vapour, pollutants such as formaldehyde, ammonia and many other common and chemical solvents such as paints and glues, or can be a by-product of mould growth. VOCs cause irritation to the eyes and or nose as well as causing headaches, nausea, and even potential damage to the central nervous system. Pressed wood furniture, newly decorated rooms, paint and cleaning solvents are common sources of VOCs.

Mould / Fungus: These can affect our respiratory system and cause allergic reactions, like a runny nose, eye  and throat irritation, headaches, fatigue and aggravation of asthma. Other indoor pollutants include bacteria, viruses, dust mites and pollen.
Emissions from electronic office equipment: Many studies, including those from EPA and the University of California Berkley, have reported that emissions from office equipment such as computers and printers, include VOCs, ultra-fine particles and ozone. These emissions have been proven to have a negative effect on the health of many people which can be reduced by using an air purifier.
Using HEPA and Activated Carbon filters: An effective HEPA filter is absolutely necessary to remove particles, even at a microscopic level; it ensures that the particles are not spread. The antibacterial activated carbon on the EAP300PM2.5HC is a natural material biosynthesized from walnut shell, the absorption area of activated carbon is very large at up to 300,000 square meters. The activated carbon filter will absorb unpleasant odours and reduce the VOC content in the air.

OPERATION INSTRUCTIONS

BEFORE FIRST USE:
1) Unpack the appliance and remove the filter cover from the rear of the unit, by gently pulling the Air inlet  panel back and then lifting off the unit.

2) Remove the three filters from the rear of the unit. The pre filter should be gently freed from the slots  olding it in position, then the HEPA and Carbon filter will slide out.

3) Remove the filters from the plastic protective packaging

4) Load the filters into the rear of the unit ensuring the tags for removal are facing outwards. The pre-filter should be gently manipulated to ensure it is located into the slots in the unit.

5) Reinstall the air inlet panel by locating the base of the panel into the slots, and then pressing around the anel to clip it into place.

CONTROL PANEL

ON/OFF	Press to turn the appliance on and off.
SPEED	Press to change between the four fan speeds. The indicators will show the currently selected fan speed. When all three indicators are on, the unit is in Turbo mode.
TIMER	With the unit turned on, repeatedly press the timer button to select in how many hours it should turn off. The duration can be set between 1 an7 hours in 1 hour increments. The duration of the timer is calculated by adding the numbers of the lights illuminated. i.e. is 1h and 2h are lit, the timer is set for 3 hours. To turn off the timer, repeatedly press the timer button until all the indicator lights go out.
MODE	Press to change between operating modes: STANDARD – Unit operates with the settings selected AUTO – The fan speed will automatically adjust based on the air quality. SILENT – The fan will operate at low speed.
DISPLAY/LOCK	Press to turn the front display on and off. Press and hold for 5 seconds to lock the control panel. To reactivate the control panel press and hold for another 5 seconds.
RESET	The indicator light above the RESET button will flash when the filters are due for replacement. Once the filters have been replaced, press and hold the RESRT button for 5 seconds to restart the filter timer.

FRONT DISPLAY

The unit utilizes a PM2.5 sensor to measure the air quality. When turning the unit will take around 90 seconds before showing the air quality on the screen. The front indicator will alternate between be showing the air quality, humidity, and temperature. The display also illuminates to show a visual representation of the air quality.

CARE AND MAINTENANCE

• Always shut off the unit and unplug from the mains before cleaning or performing any maintenance.
•  When the unit is not in use for long periods, it is advisable to remove the plug from the power socket.
• Do not use chemical solvents (such as benzene, alcohol or gasoline) as they may cause irreversible damage to the unit.

CLEANING THE PRE-FILTER AND FILTER HOLDING AREA
The pre-filter should be vacuumed every 2-3 weeks to remove any debris which has accumulated on it, while cleaning the pre-filter, the filter holding area should also be wiped with a dry cloth. If used in dustier environments the pre-filter may require more regular cleaning. For a deeper clean the pre-filter can be removed and rinsed in clean water and then left to dry naturally. Ensure the pre-filter is fully dry before reinserting into the unit. The pre-filter must be replaced if there are any signs of damage.

CHANGING THE FILTERS
Remove and replace the filters following the instructions found on Page 8. Once the filters have been replaced,  press and hold the RESET button f5 seconds to reset the filter counter.

CLEANING THE AIR QUALITY SENSOR

•  Remove the cover from the sensor, checking for any signs of blockage in the holes. Any blockages should be removed using a soft brush.
•  Wipe the sensor and air inlet/outlets with a damp cotton bud. It should then be dried by wiping with a dry  cotton bud before replacing the cover. For optimal performance, the sensor should be cleaned every two months.

CLEANING THE CASE

• Only use tepid water and a mild detergent on a soft cloth.
• Do not use bleach or abrasives.
• Do not splash water directly onto the main unit.
• Avoid wetting the power connection port, doing so may cause an electric shock and can lead to the insulation deteriorating or unit to rust.

CLEANING THE FILTER COVER AND CLEAN AIR OUTLET

• • Use water and a mild detergent.
•  Do not use bleach or abrasives.
• Do not spray water inside the unit.
•  If the clean air outlet grilles get soiled easily, use a vacuum attachment or soft brush to clean.
•  If the filter cover is dirty, hoover it. If it is heavily soiled, wash it with warm soapy water and dry thoroughly before reinserting it in the unit.

NOTE: Do no assemble the unit and power it on before all the parts are completely dry. Any other maintenance than what is described in this user manual must be only performed by the service centre.

TECHNICAL SPECIFICATION

TROUBLESHOOTING

electriQ UK SUPPORT

www.electriQ.co.uk/support
Please, for your own convenience, check the troubleshooting guide before calling the service line.
If the unit still fails to operate call: 0871 620 1057 or complete the online form Office hours: 9AM – 5PM Monday to Friday

www.electriQ.co.uk
Unit J6, Lowfields Way
Elland, West Yorkshire
HX5 9DA

Do not dispose this product as unsorted waste. Collection of such waste must be handled separately as special treatment is necessary.

Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centres.

USER MANUAL

ELECTRIC PURE COOL TOWER PURIFIER FAN
IQ-PURECOOLB – Black
IQ-PURECOOLS – Silver

Thank you for choosing electric
Please read this user manual before using this innovative air purifier and keep it safe for future reference.
Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

SAFETY

• Carefully read the instructions before operating the unit.
• This appliance is for indoor use only.
•  This unit must only be connected to a 220-240V / 50Hz earthed outlet.
•  Installation must be in accordance with the regulations of the country where the unit is used.
•  If you are in any doubt about the suitability of your electrical supply, have it checked and, if necessary, modified by a qualified electrician.
•  This air purifier has been tested and is safe to use. However, as with any electrical appliance – use it with care.
• Disconnect the air purifier from the socket when changing the filters or cleaning the unit.
•  Avoid touching any moving parts within the appliance.
• Never insert fingers, pencils or any other objects through the guard.
•  This device is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities. It is also not intended for use by those with a lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
•  Do not leave children unsupervised with this device.
•  Do not clean the unit by spraying it or immersing it in water. Use a damp cloth only. Never allow water or vapors to enter the unit.
• Do not clean with strong chemical agents or other abrasive materials.
• Never connect the unit to an electrical outlet using an extension cord. If a power outlet is not available, one should be installed by a qualified electrician.
•  Never operate this appliance if the cord or power supply are damaged. Ensure the power cord is not stretched or exposed to sharp objects/edges.
•  A damaged power supply should be replaced by the manufacturer. Never extend or attempt to change the power supply lead.
• Any service other than a regular cleaning or filter replacement should be performed by an authorized service representative. Failure to comply could result in a voided warranty.
•  Do not use the appliance for any purpose other than its intended use.
• Avoid removing the power cord from the socket whilst the unit is still in operation. This could cause electrical damage.
•  Never use the power supply as a switch to start and turn off the air purifier. Use the provided ON/OFF button located on the control panel.
•  Always place the unit on a dry and stable surface.
•  The use of accessory attachments that have not been approved by the appliance manufacturer is not recommended, as this may result in fire, cause an electric shock and/or cause personal injury.
•  Ensure hands are fully dried before plugging or unplugging the appliance.
• The appliance should not be installed in the laundry or wet rooms.

ABOUT YOUR AIR PURIFIER

As well as acting as a fan providing effective personal comfort, this IQ-PURE COOL air purifier provides multiple stages of air purification. This unit features HEPA and activated carbon filters for improved air filtration.

•  Antibacterial HEPA filter removes 99.5% of airborne particles of 0.25 micrometers or larger.
• Activated carbon filter removes unpleasant odours and absorbs harmful substances such as formaldehyde and benzenes.

APPLICATIONS:

• Personal use in domestic and office space to improve air quality
• Helps smokers to reduce contaminants within the air
• Can help improve the symptoms of asthma and pollen allergies
• Great for children’s rooms and small offices

FEATURES

• LED display with touch screen controls
• 12 hours start / stop timer
• Easy to use remote control with magnetic holder
•  Quiet DC motor with 9 fan speeds
•  Oscillation function
• Adjustable vertical airflow direction
• Dual filter compartments

NOTE: This air purifier is not a substitute for proper ventilation, regular vacuum cleaning or for use in place of a cooker hood whilst cooking. If the relative humidity is above 60% we recommend using a dehumidifier to reduce the humidity.
IMPORTANT
Before first use ensure that all the packaging has been removed from the filters and that they are inserted correctly into the filter compartments.

INFORMATION ON INDOOR POLLUTANTS

VOC (Volatile Organic Compound): VOCs come from motor vehicle exhausts, gasoline vapour, pollutants such as formaldehyde, ammonia and many other common and chemical solvents such as paints and glues, or can  be a by-product of mould growth. VOCs cause irritation to the eyes and or nose as well as causing headaches,  nausea and even potential damage to the central nervous system. Pressed wood furniture, newly decorated rooms,
paint and cleaning solvents are common sources of VOCs.
Mold / Fungus: These can affect our respiratory system and cause allergic reactions, like a runny nose, eye and  throat irritation, headaches, fatigue and aggravation of asthma. Other indoor pollutants include bacteria, viruses, dust mites and pollen.
Emissions from electronic office equipment: Many studies, including those from EPA and the University of  California Berkley, have reported that emissions from office equipment such as computers and printers, include  VOCs, ultra-fine particles and ozone. These emissions have been proven to have a negative effect on the health of  many people which can be reduced by using an air purifier.
Using HEPA filters and Activated Carbon filters An effective HEPA filter is absolutely necessary to remove particles, even at a microscopic level; it ensures that the particles are not spread. The antibacterial activated carbon on the IQ-PURE COOL is a natural material biosynthesized from walnut shell, the absorption area of activated carbon is very large at up to 300,000 square meters. The activated carbon filter will absorb unpleasant odours and reduce the VOC content in the air.

ENERGY-SAVING AND UNIT SAFETY PROTECTION TIPS

• Do not cover or restrict the airflow from the outlet or inlet grills.
•  For maximum performance and safety, the minimum distance from a wall or objects hould be 30cm. Keep  away from other electrical appliances.
• Keep the filters clean. Under normal conditions, filters should only need cleaning once every two weeks  (approximately). Since the filters remove airborne particles, more frequent cleaning may be necessary,  depending on the air quality.

PRODUCT DIAGRAM

REMOTE CONTROL

OPERATING INSTRUCTIONS

POWER BUTTON	Press the power button to turn the air purifier on and off. When first turned on the fan will default to medium speed (F5)
FAN SPEEBUTTON	Repeatedly press the fan button to scroll through the 9 fan speeds between Low (F1) and High (F9).
TIMER BUTTON	The timer can be set to either turn the appliance on or off. It has a duration of up to 12 hours, and can be set in 15 min intervals up to 1 hour, and then in 1-hour increments. ON TIMER: This can be set by repeatedly pressing the timer button while the unit is in standby. OFF TIMER: This can be set by repeatedly pressing the timer button while the unit is running.
OSCILLATION BUTTON	Press to turn the oscillation function on. When activated the unit will slowly turn from left to right.
REMOTE CONTROL	The remote control offers the same functionality as the control panel, with the added benefit of multiple buttons for the timer and fan speed.

USING THE TOUCH CONTROLS

• The controls respond to touch, so you don’t need to apply any pressure.
• Use the ball of your finger, not its tip.
• Make sure the controls are always clean, dry, and that no objects are covering them.
  

CARE AND MAINTENANCE

Always turn off the unit and unplug from the mains before cleaning or performing any maintenance.

•  When the unit is not in use for long periods, it is advisable to remove the plug from the power socket.
• Do not use chemical solvents (such as benzene, alcohol or gasoline) as they may cause irreversible damage to the unit.
• Do not assemble the unit and power it on before all the parts are completely dry. Any other maintenance than what is described in this user manual must be only performed by the service centre.

CHANGING THE FILTER

The life of the filters will vary depending both on the amount of use the appliance receives, and the air quality in the area the appliance is situated. We advise the filters to be replaced every six months based on a normal operating environment. During filter maintenance, it is advisable to swap the filters between the primary and secondary compartments to maintain performance and extend their life.

Open the filter covers by gently removing the 2 side panels. Remove the old filters by simply pulling on the tabs to release them. Replace the filters before refitting the filter covers, ensuring the covers click into place.

REPLACEMENT FILTERS

We offer both a replacement set of HEPA + Activated Carbon filter (FIL-IQ-PURECOOL)
and an enhanced HEPA filter (HPFILTER-IQ-PURECOOL) which are available from the same stockist as the appliance and are available under the references below.

FIL-IQ-PURECOOL
Replacement filter pack (1 x HEPA and 1 x ACTIVATED CARBON). Two packs should be ordered if replacing  the filters in both the Primary and Secondary compartments. This is great for typical use with similar sized HEPA  and Activated Carbon filters which offer a good balance of filtering dust, mould, pollen while also removing odours from the air, such as the smell of tobacco smoke or VOCs.

HPFILTER-IQ-PURECOOL
Enhanced filter pack containing a 2-in-1 filter. The dual filter contains an enhanced True HEPA filter with a  greater filtration surface while still incorporating a slimmer activated carbon layer. This will provide upgraded  performance when placed in the primary filter compartment and is ideal in smoke free environments. It is great at  combating pet dander, pollen, mites and reducing allergens. This filter can be used in combination with standard  filters in the secondary compartment, or one can be placed in each compartment for a further increase in performance.

CLEANING THE UNIT

•  Only use tepid water and a mild detergent on a soft cloth.
•  Do not use bleach or abrasives.
• Do not splash water directly onto the main unit.

CLEANING THE FILTERS AND FILTER HOLDING AREA

• Hoover the filters gently every 2-3 weeks or more often if used in dusty or polluted environments.
•  Ensure the filters are not damaged during the cleaning process and replace if they show any signs of damage.
• Wipe the filter holding area with a dry cloth if necessary.

CLEANING THE FILTER COVER AND CLEAN AIR OUTLET

• Use water and a mild detergent.
• Do not use bleach or abrasives.
•  Do not spray water inside the unit.
• f the clean air outlet grilles get soiled easily, use a vacuum attachment or soft brush to clean.

TROUBLESHOOTING

DISPOSAL
Disposal: Do not dispose this product as unsorted waste. Collection of such waste must be handled separately as special treatment is necessary.
Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participate sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centers.
electriQ UK SUPPORT
www.electriQ.co.uk/support
Please, for your own convenience, check the troubleshooting guide before calling the service line.
If the unit still fails to operate call: 0871 620 1057 or complete the online form Office hours: 9AM – 5PM Monday to Friday
www.electriQ.co.uk
Unit J6, Lowfields Way
Elland, West Yorkshire
HX5 9DA

SPECIFICATION

PRODUCT FICHE

	IC)-PURECOOL8 & 10-PURECOOLS BLADELESS AIR PURIFIER
Description	Symbol	Value	Unit
Maximum fan flow rate	F	2.	m3/min
Fan power input	P	30	W
Service Value	SV	0.08	(m3/min)W
Standby power consumption	Pa	0.3	W
Fan sound power level	LwA	81	dB(A)
Maximum air velocity	c	8.	Meters/sec
Measurement standard for service value	Service value measured when used as a comfort fan, without the filters fitted following commission Regulation (EU) 206/2012
Contact details for obtaining more information	eA ectd0. Unit J6. Lowfields Way. Elland. West Yorkshire. HX5 WA

electriQ Air Conditioner User Manual

Thank you for choosing electriQ
Please read this user manual before using this innovative Air Conditioner and keep it safe for future reference.

Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

SAFETY INSTRUCTIONS

Important!

• Carefully read the instructions before operating the unit
• This appliance is for indoor use only.
• Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet.
• Installation must be in accordance with regulations of the country where the unit is used.
• If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, modified by a qualified electrician.
• This air conditioner has been tested and is safe to use. However, as with any electrical appliance – use it with care.
• Disconnect the power from the appliance before dismantling, assembling or cleaning.
• Avoid touching any moving parts of the appliance.
• Never insert fingers, pencils or any other objects though the guard
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities. It is also not intended for use by those with a lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
• Do not leave children unsupervised with this appliance.
• Do not clean the unit by spraying it or immersing it in water.
• Never connect the unit to an electrical outlet using an extension cord. If an outlet is not available, one should be installed by a qualified electrician.
• Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not stretched or exposed to sharp objects/edges.
• A damaged supply cord should be replaced by the manufacturer or a qualified electrician in order to avoid a hazard.
• Any service other than regular cleaning or filter replacement should be performed by an authorised service representative. Failure to comply could result in a voided warranty.
• Do not use the appliance for any purpose other than its intended use.
• The air conditioner unit must always be stored and transported upright, otherwise irreparable damage may be caused to the compressor; if in doubt we suggest waiting at least 24 hours before starting the unit.
• Avoid restarting the air conditioning unit unless 3 minutes have passed since being turned off. This prevents damage to the compressor.
• Never use the mains plug as a switch to start and turn off the air conditioning unit. Use the provided ON/OFF button located on the control panel.
• Always place the unit on a dry and stable surface.
• The appliance should not be installed in laundry or wet rooms.
• The appliance must be placed in a room without sources of ignition (for example: open flames, an operating gas appliance or an operating electric heater).
• R290 refrigerant gas complies with European environmental directives.
• R290 has a low GWP (Global Warming Potential) of 3.
• The air conditioner contains about 300 g of R290 refrigerant gas.
• Do not use or store in an unventilated space with an area smaller than 14.4 m2 per unit.
• The room must be such as to prevent stagnation of possible leaks of refrigerant gas as there could be a danger of fire or explosion should the refrigerant come into contact with electric heaters, stoves or other sources of ignition.
• Refrigerant gas may be odourless.
• Do not use the product and contact the retailer for advice, if damage has occurred to the unit which may have compromised the refrigerant system.
• Any repairs or maintenance must only be carried out on the unit by a suitably qualified engineer. Before opening and servicing the unit the authorised engineer must be in possession of a copy of the manufacturer’s service manual and must follow the safety information contained within it to ensure all hazards are minimized.
• The refrigerant system should not be perforated or punctured.

Energy Saving and Unit Safety Protection Tips

• Do not cover or restrict the airflow from the outlet or inlet grills.
• For maximum performance the minimum distance from a wall or objects should be 50cm.
• Keep the filters clean. Under normal conditions, filters should only need cleaning once every three weeks (approximately). Since the filters remove airborne particles, more frequent cleaning maybe necessary, depending on the air quality.
• For the initial start-up set the fan speed to maximum and the thermostat to 5 degrees lower than the current temperature. After, set the fan switch to low and set the thermostat to your desired setting.
• To protect the unit, we recommend not using the cooling function when the ambient temperature is higher than 35oC.

FEATURES AND PARTS LIST

• 3 in 1 Cooling, Fan, Dehumidifier great for Rooms up to 30 sqm.
• 5 speed DC fan: balancing quiet operation with performance.
• SmartCool Logic for Improved Energy Efficiency.
• HEPA Filter for Air Purification
• 24 Hours Start / Stop Timer
• Digital Thermostat.
• Auto-Restart to retain the settings in the event of power failure.
• Smart Colour Changing Indicator LED
• Remote Control
• Castors and Handles for Enhanced Portability

INSTALLATION

WARNING: Before using this unit, please keep it upright for at least 3-4 hours.

This unit can easily be moved from one room to another. While moving the unit please note that it must always be kept upright and then placed on an even surface.

1. Attach the fishtail connector to the end of the hose, by extending the end and twisting until firmly attached (At least 3 full rotations).                         
2. Attach the connector on the opposite end of the pipe to the exhaust outlet on the rear of the appliance by putting into position and twisting to lock in place. 
3. Make sure the unit is upright and there are no obstructions to the air inlets and outlet grills.

INSTALLATION OF WINDOW KIT

The window kit (slide bar and fishtail) can be used with sliding windows and doors. For other types of window, the fishtail should be used on its own.

1. Partially open the window and place the extended slide bar in position before closing the window onto it.                                                                
2. Fix the fishtail adaptor into the opening on the slide bar 
3. Fix the exhaust connector on the opposite end of the exhaust hose to the exhaust outlet on the rear of the air conditioner.

INSTALLING THE HEPA FILTER (OPTIONAL)

The air conditioner can accommodate a HEPA filter which will purify the air expelled back into the room in any operating mode. These can be purchased from the stockist using the code: FIL-ECOSILENTHEPA.

The HEPA filter should be unwrapped and installed in the upper air inlet. To install, remove the upper filter frame from the air conditioner by pressing the two clips on the top of the filter frame. Place the HEPA filter within the filter frame before refitting onto the unit.

In order to maintain performance, the filter should be regularly vacuumed. The filter should be replaced every six months, depending on usage and air quality.

NOTES:

• The window kit is only designed to be installed with sliding or sash windows or doors. The window kit is not designed or to be used with any other style of windows.
• The fish tail adaptor can be used without the slide bar with most windows / doors.
• When using the air conditioner ensure that the opening left around the fishtail is as small as possible as the cooling will be less efficient.
• The best form of installation is through a wall duct. By properly venting you expel hot air from your room while efficiently cooling it.
• Your air conditioner should be used without the vent pipe in dry mode. When using dry mode ensure that an external water tank is used, monitored and regularly emptied before overflowing. Permanent plumbing can be also installed for dry mode or an external uplift water pump can be set up for unattended use.

IMPORTANT SAFEGUARDS

The length of the soft hose extends from approximately 35 cm to 200 cm. If hose is extended above this length, the unit may malfunction which can invalidate the warranty. The outlet vent must be well ventilated and not obstructed as this will cause the unit to overheat. Keep the hose as straight and short as possible and avoid bending the air hose by more than 30 degrees in order not to reduce the performance of the unit.

OPERATION

REMOTE CONTROL

NOTE: The design of the remote may vary from the diagram, due to continuous product improvement.

SMART INDICATOR LED

The air conditioner contains a Smart Indicator which changes colour to show from a distance what mode the air conditioner is set to.

COOL MODE
The indicator will display Blue.

SMART COOL MODE
The indicator will display Blue.

FAN (AIR PURIFIER) MODE
The indicator will display Green.

DRY (DEHUMIDIFY) MODE
The indicator will display Orange.

MULTI PROTECTIVE FUNCTIONS

FROST PROTECTION
In COOL, DRY or SMART COOL modes, if the temperature of the exhaust is too low, the machine will automatically stop operating until the temperature has risen.

OVERFLOW PROTECTION
When the water in the internal water tank exceeds the warning level, the machine will stop operating and sound an alarm with the LCD display showing “E7”. To resume operation empty the internal water tank. After the water is emptied, the machine will automatically return to the original state.

AUTO-DEFROST
The machine has automatic defrosting function. If during operation the temperature of the internal coils drops too low, the unit will enter auto defrost and the heating symbol will flash on the control panel.

AUTOMATIC THERMAL PROTECTION
To protect the service life of the machine, the machine has automatic thermal protection. If the temperature within the unit is outside of the specified range, the compressor and the lower motor will stop operation. The appliance will automatically return to normal operation after the temperature of the machine recovers.

COMPRESSOR PROTECTION
To prevent damage to the compressor there is a 3 minute delay start protection function.

EMPTYING THE INTERNAL WATER TANK

When the internal water tank is full the unit will stop working.
Shut off the unit and unplug. Try not to move the model abruptly as this may cause the water in the internal tank to spill out.

Place a tray under the lower water plug or place the unit in a drainage area.
Unscrew the drain plug cap and remove the rubber stopper – water will drain from the internal tank. Put the rubber stopper back and screw the drain plug cap back into place.

Unscrew the drain plug cap and remove the rubber stopper.
Connect a water pipe to the upper water outlet.
You can plumb this pipe into your current plumbing system, lead it outside and use gravity fall or use a water pump.

NOTE: This model has a self-evaporative function, which reduces the need to empty the water tank. If the unit is vented correctly most of the water is reused to cool the condenser coils and any excess is evaporated. Please do not use continuous drainage if you intend to use the self-evaporating facility.

MAINTENANCE AND CLEANING

PLEASE TURN OFF THE UNIT AND UNPLUG FROM THE MAINS BEFORE CLEANING OR PERFORMING ANY MAINTENANCE

CLEAN THE SURFACE
Clean the surface of the machine with a wet soft cloth. Do not use chemicals, such as benzene, alcohol, gasoline, etc; otherwise, as this may cause damage to the surface and or the internal workings of the machine

AIR FILTER CLEANING
If the filter screen is clogged with dust, the effectiveness of the air conditioner is reduced. The filter screen should be cleaned once every two weeks or as often as necessarily in your environment.

CLEAN THE UPPER FILTER SCREEN FRAME
Unclip the top of the evaporator filter screen from the appliance, and remove the HEPA filter (if installed). The HEPA filter should be regularly vacuumed and replaced when necessary (approx. every 6 months dependant on usage)
The evaporator filter screen can be cleaned in warm water with neutral detergent (about 40℃ /104℉). It must be rinsed clean and dried in the shade before reinstalling in the unit.

HEPA filters can be purchased from the stockist using the code: FIL-ECOSILENTHEPA.

CLEAN THE LOWER FILTER SCREEN FRAME
Hold the handle of the air inlet filter screen frame, and pull it outward gently to remove it.
Put the filter screen into warm water with neutral detergent (about 40℃ / 104 ℉). It must be rinsed clean and dried in the shade before reinstalling in the unit.

END OF SEASON MAINTENANCE

1. Remove the rubber stopper from the drainage hole and empty the internal tank. You can also drain the water by leaning the unit.
2. Then switch the unit to low fan mode.
3. Keep the unit in this mode for half day – until the conduit is dried. Doing this helps to keep the inside of the unit dry and prevents mould from developing
4. Turn off the unit and pull out the plug.
5. Replace the rubber stopper.
6. Coil the wire and bind it together, then put it into the accessories space.
7. Separate the air-exhaust pipe and store it safely.
8. Cover the unit and keep it in a dry place.
9. Take the batteries out of remote control and store or dispose of them safely. Keep all accessories with the unit ready for next season.

TROUBLESHOOTING

Do not repair or disassemble the air conditioning. Unqualified repair will invalidate the warranty and may lead to failure, causing injuries and property damage. Only use it as directed in this user manual and only perform operations advised here.

If problems not listed in the table occur or recommended solutions do not work, please contact the service centre.

ERROR CODES

APPENDIX

Disposal: Do not dispose this product as unsorted municipal waste. Collection of such waste must be handled separately as special treatment is necessary. Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating civic amenity sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centres.

electriQ UK SUPPORT

www.electriQ.co.uk/support

Please, for your own convenience, make these simple checks before calling the service line. If the unit still fails to operate call the number below, or complete the online form.

0871 620 1057

1. Has the unit been standing upright for at least 2 hours?
2. Is the unit plugged into the mains?
3. Is the fuse OK?
4. Switch the unit off and wait three minutes to see if the issue is resolved. Restart the unit.
5. Check if the water tank is full.

Office hours: 9AM – 5PM Monday to Friday
www.electriQ.co.uk
Unit J6, Lowfields Business Park
Lowfields Way, Elland
West Yorkshire, HX5 9DA

TECHNICAL DATA

Unit must be vented outside when in Air Cooling mode. For the purposes of EU regulation EN12102 this is a local air conditioner and produces less than 65dB(A) sound energy.

R 290

electriQ Portable Air Conditioner User Manual

SAFETY INSTRUCTIONS

Important!

•  Carefully read the instructions before operating the unit
• This appliance is for indoor use only.
•  Rating: This unit must be only connected to a 220-240 V / 50 Hz earthed outlet.
• Installation must be in accordance with regulations of the country where  the unit is used.
•  If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary, modified by a qualified electrician.
•  This air conditioner has been tested and is safe to use. However, as with any electrical appliance – use it with care.
• Disconnect the power from the appliance before dismantling, assembling or cleaning.
• Avoid touching any moving parts of the appliance.
•  Never insert fingers, pencils or any other objects though the guard
•  This appliance is not intended for use by persons (including children)  with reduced physical, sensory or mental capabilities. It is also not intended for use by those with a lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
•  Do not leave children unsupervised with this appliance.
• Do not clean the unit by spraying it or immersing it in water.
•  Never connect the unit to an electrical outlet using an extension cord. If  an outlet is not available, one should be installed by a qualified electrician.
• Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not stretched or exposed to sharp objects/edges.
• A damaged supply cord should be replaced by the manufacturer or a qualified electrician in order to avoid a hazard.
•  Any service other than regular cleaning or filter replacement should  be performed by an authorised service representative. Failure to comply  could result in a voided warranty.
•  Do not use the appliance for any other purposes than its intended use.
•  The air conditioner unit must always be stored and transported upright, otherwise irreparable damage may be caused to the compressor; if indoubt we  suggest waiting at least 24 hours before starting the unit.
•  Avoid restarting the air conditioning unit unless 3 minutes have passed  since being turned off. This prevents damage to the compressor.
•  Never use the mains plug as a switch to start and turn off the air  conditioning unit. Use the provided ON/OFF switch located on the control panel.
•  Always place the unit on a dry and stable surface.
•  The appliance should not be installed in laundry or wet rooms.
•  The appliance must be placed in a room without sources of ignition  (for example: open flames, an operating gas appliance or an operating electric heater).
•  R290 refrigerant gas complies with European environmental directives.
• R290 has a low GWP (Global Warming Potential) of 3.
•  The air conditioner contains about 20 g ofR290 refrigerant gas.
•  Do not use or store in an unventilated space with an area smaller than 1m2  per unit. The room must be such as to prevent stagnation of possible leaks of refrigerant gas as there could be a danger of fire or explosion hazard  should the refrigerant come into contact with electric heaters, stoves or other sources of ignition.
• If the appliance is installed, used or stored in an unventilated room, the room must be such as to prevent stagnation of possible leaks of refrigerant gas as
  there could be a danger of fire or explosion should the refrigerant come into contact with electric heaters, stoves or other sources of ignition.
•  Refrigerant gas may be odourless.
• Do not use the product and contact the retailer for advice, if damage ha occurred to the unit which may have compromised the refrigerant system.
•  Any repairs or maintenance must only be carried out on the unit by a  suitably qualified engineer. Before opening and servicing the unit the authorized engineer must be in possession of a copy of the manufacturer’s service manual and must follow the safety information contained within it to ensure all hazards are minimized.
• The refrigerant system should not be perforated or punctured.

Energy Saving and Unit Safety Protection Tips

• Do not cover or restrict the airflow from the outlet or inlet grills.
• For maximum performance the minimum distance from a wall or objects should be 50cm.
•  Keep the filters clean. Under normal conditions, filters should only  need cleaning once every three weeks (approximately). Since the filters remove airborne particles, more frequent cleaning maybe necessary, depending on the air quality.
• For the initial start up set the fan speed to maximum and the thermostat to 4- 5 degrees lower than the current temperature. After, set the fan switch to  low and set the thermostat to your desired setting.
• To protect the unit we recommend not using the cooling function when the ambient temperature is higher than 35oC

FEATURES AND PARTS LIST

FEATURES

• Self-evaporative system – no external water tank needed
•  Designer inspired luxury model
•  Bright LED screen, indicates temperature and operation mode
•  On/Off timer function – allows you to choose when the unit operates
•  Compressor protection technology

PARTS LIST

INSTALLATION

Warning: Before using this unit, please keep it upright for at least 3-4 hours. This unit can easily be moved from one room to another. While moving the unit please note that it must always be kept upright and then placed on an even surface.

1. Attach the fishtail connector to the end of the hose, by extending the end of the hose and twisting the fishtail adaptor until it is firmly attached (At least 3 full rotations)
   
2. Attach the connector on the opposite end of the pipe to the exhaust outlet on the rear of the appliance by putting it into position and twisting to lock in place.
   
3. Make sure the unit is  upright and there are no obstructions to the air inlet and outlet grills.
   

INSTALLATION OF WINDOW KIT

The window kit (slide bar and fishtail) can be used with sliding windows and doors. For other types of window, the fishtail should be used on its own.

1. Partially open the window and then fix the window kit to the window.
   
2. Fix the fishtail on the hose into the opening in the slide bar.

NOTES:

• The window kit is only designed to be installed with sliding or sash windows or doors. The window kit is not designed or to be used with any other style of  windows.
• The fish tail adaptor can be used without the slide bar with most windows / doors.
• When using the air conditioner ensure that the opening left around the fishtail is as small as possible to ensure efficient operation.
• The best form of installation is through a wall duct. By properly venting you expel hot air from your room while efficiently cooling it.
•  Your air conditioner should be used without the vent pipe in dehumidifier mode. When using dehumidifier mode ensure that an external water tank is  used, monitored and regularly emptied before overflowing. Permanent plumbing can be also installed for dehumidifier mode or an external uplift water pump can be set up for unattended use.

IMPORTANT SAFEGUARDS
The length of the soft hose extends from 28 cm to 150 cm. If hose is extended above this length the unit may malfunction and this can invalidate the warranty. The outlet vent must be well ventilated and not obstructed as this will cause the unit to overheat. Avoid bending the air hose more than 30 degrees.

OPERATION

This portable air conditioner boasts 3 modes: Cooling, Dehumidifying and Fan. The fan has two speeds: high and low. Temperature range settings are: 16-31Ԩ. The unit will also display operating function, temperature, fault diagnostics and protective functions on the display.

1. Swing Button
2. Timer Button
3. Fan Speed Button
4. Up button
5. Display
6. Down Button
7. mode Button
8. Sleep Button
9. Power Button

POWER BUTTON: Press to turn the machine in and off. In the case of power on.

MODE BUTTON: Press to change between cooling, fan and dehumidifier modes.
COOLING MODE: Cold air will be expelled through the front of the unit and hot air will be expelled through the vent hose.
DEHUMIDIFIER MODE: The unit should be set up without a vent hose, moisture is extracted from the air that passes through the unit. Continuous drainage should be set up for the moisture collected (Drainage pipe not included).
FAN MODE: No cooling effect, circulates air within the room, vent pipe not required.

UP AND DOWN BUTTONS: These can be used to set the desired temperature between 16 – 31
Following pressing the TIMER button, they are also used to set the timer length. Press both buttons at the same time to change the display between C and F .

FAN SPEED BUTTON:
IN COOLING AND FAN MODE: Press to change between high, medium and low fan speeds.
IN DEHUMIDIFY MODE: The fan will default to low speed and cannot be adjusted.

TIMER BUTTON: Timer functions cannot be combined or repeated. POWER ON TIMER:
With the appliance turned off, press the “TIMER” button to setup the power-on time. Press the UP and DOWN buttons to adjust the duration of the timer (from 1 to 24 hours). Timer indicator turns on. The unit will start after selected number of hours.

POWER OFF TIMER:
With the appliance running with the desired settings, press the “TIMER” button to setup the power – off timer. Press the UP and DOWN buttons to adjust the duration of the timer (from 1 to 24 hours). The timer indicator will illuminate. The unit will stop after selected number of hours. 1:Swing Button 2:Timer Button 3:Fan  Speed Button 4:Up button 5:Display 6:Down Button 7:mode Button 8:Sleep Button 9:Power Button

SLEEP BUTTON:Press to turn on the sleep mode
While the sleep mode is activated in cooling mode, after one hour the desired temperature will be increased by 1ºC, after another hour the desired temperature will increase by another 1ºC and remain at that level. This means the unit will spend less time with the compressor running, and so run quieter. Press the MODE button until the sleep mode indicator is illuminated, the fan speed is set to low. Sleep mode cannot be used in dehumidifying and fan mode. If the internal tank becomes full, the machine will turn off and sleep mode will be cancelled.

REMOTE CONTROL

The air conditioner can be controlled with the remote control. Two AAA-batteries are required to use the remote control.

• POWER : Press the POWER button to turn the machine on and off.
• MODE : Press the MODE button to switch between cooling, fan, Dehumidify modes.
• UP : press the UP button to increase the desired temperature and set the duration of the timer.
• DOWN : press the DOWN button to reduce the desired temperature and set the duration of the timer.
• FAN : Press the FAN button to cycle between high, medium and low fan speeds.
• TIMER : Press the TIMER button to set the duration of the power on or power off timer..
• SWING : Press the swing button to change the orientation of the louvres to direct the air
• TEMPERATURE UNIT : Press to switch between displaying the temperature in Celsius and Fahrenheit.
• SLEEP MODE : Press to turn on the sleep mode. The unit will work with energy saving logic and the lowest fan speed.

MULTI PROTECTIVE FUNCTIONS

OVERFLOW PROTECTION FUNCTION

When the water in the internal water tank exceeds the warning level, the machine will automatically sound an alarm, and the Full light will illuminate. At this point, you need to empty the internal water tank. After the water is emptied, the machine will automatically return to the original state.

AUTOMATIC DEFROSTING (COOLING MODELS HAVE THIS FUNCTION)

The machine has automatic defrosting function: during defrosting, heating symbol on the display screen will flash.

AUTOMATIC THERMAL PROTECTION

To protect the service life of the machine, the machine has automatic thermal protection.  During the protection period, the compressor and the lower motor will stop operation and will automatically return to normal heating state after the temperature of the machine recovers.

PROTECTION FUNCTION OF THE COMPRESSOR

To increase the service life of the compressor, it has a 3- minute delay start protection function

EMPTYING THE INTERNAL WATER TANK

MANUAL DRAINAGE:

When the internal water tank is full the unit will stop working. Shut off the unit and unplug. Try not to move the model abruptly as this may cause the water in the internal tank to spill out. Place a tray under the water plug or place the unit in a drainage area. Remove the rubber stopper – water will drain from the internal tank. Put the rubber stopper back into place.

CONTINUOUS DRAINAGE:

Unscrew the drain plug cap and remove the rubber stopper. Connect a water pipe to the water outlet. (Not Supplied) You can plumb this pipe into your current plumbing system, lead it outside and use gravity fall or use a water pump.

Note: This model has a self-evaporative function, which reduces the need to empty the water tank. If the unit is vented correctly most of the water is reused to cool the condenser coils and any excess is evaporated. Please do not use continuous drainage if you intend to use the self-evaporating facility.

MAINTENANCE

CLEANING

PLEASE TURN OFF THE UNIT AND UNPLUG FROM THE MAINS BEFORE CLEANING OR PERFORMING ANY MAINTENANCE

CLEAN THE SURFACE
Clean the surface of the machine with a wet soft cloth. Do not use chemicals, such as benzene, alcohol, gasoline, etc; otherwise, as this may cause damage to the surface and or the internal workings of the machine.

AIR FILTER CLEANING

If the filter screen is clogged with dust, the effectiveness of the air conditioner is reduced. The filter screen should be cleaned once every two weeks or as often as necessarily in your environment.

CLEAN THE UPPER FILTER SCREEN FRAME

Grip the edge of the evaporator filter screen frame with both hands. Pull out to remove the filter screen from its frame. If present, unscrew the screws fixing the filter before removing it (as shown in the above figure).
Put the evaporator filter screen into warm water with neutral detergent (about 40C /104 F) and dry it in the shade after rinsing clean.

END OF SEASON MAINTENANCE

1. Remove the rubber stopper and drain plug cap from the drainage hole and empty the internal tank. You can also drain the water by leaning the unit.
2. Then switch the unit to low fan mode.
3.  Keep the unit in this mode for half day – until the conduit is dried. Doing this helps to keep the inside of the unit dry and prevents mould from developing
4. Turn off the unit and pull out the plug.
5.  Replace the rubber stopper and drain plug cap
6.  Coil the wire and bind it together, then put it into the accessories space.
7.  Separate the air-exhaust pipe and store it safely.
8. Cover the unit and keep it in a dry place.
9. Take the batteries out of the remote control and store or dispose of them safely Keep all accessories with the unit ready for next season.

TROUBLESHOOTING

Do not repair or disassemble the air conditioning. Unqualified repair will invalidate the warranty and may lead to failure, causing injuries and property damage. Only use it as directed in this user manual and only perform operations advised here.

If problems not listed in the table occur or recommended solutions do not work, please contact the service centre.

APPENDIX

Disposal: Do not dispose this product as unsorted municipal waste. Collection of such waste must be handled separately as special treatment is necessary. Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participating civic amenity sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centres.

MODEL	SILENT16-V2
Capacity Cooling	4.69kWh, 16,000BTU
Rated Input	1.600 kW
Running Current	8A
Air Flow	480m3/h
EER rate	A
Compressor	Rotary, R290 gas
Noise	38-48dB(A) Sound Energy <65dB(A) Sound Power
Thermostat	16-31°C
Moisture removal	33 L/Day
Permitted Excessive Operating Pressure	0.6/1.8MPa
Maximum Allowable Pressure	3.0Mpa
Power Supply	220-240V/501-$z
Net Weight	33kg
Dimension(L*D*H)	480*390*780mm
Unit must be vented outside when in Air Cooling mode. For the purposes of EU regulation EN12102 this is a local air conditioner and produces less than 65dB(A) sound energy. A

electriQ UK SUPPORT

http://www.electriq.co.uk/support

Please, for your own convenience, make these simple checks beforecalling the service line. If the unit still fails to operate call the number below, or complete the online form.

0871 620 1057

1. Has the unit been standing upright for at least 2 hours?
2.  Is the unit plugged into the mains?
3.  Is the fuse OK?
4.  Switch the unit off and wait three minutes to see if the issue is resolved. Restart the unit.
5. heck if the water tank is full.

Office hours: 9AM – 5PM Monday to Friday
www.electriQ.co.uk
Unit J6, Lowfields Business Park
Lowfields Way, Elland
West Yorkshire, HX5 9DA

Thank you for choosing electrIQ Please read this user manual before using this innovative Air Purifier and keep it safe for future reference. Visit our page www.electrIQ.co.uk  for our entire range of Intelligent Electricals

Safety Instruction

Important

• Carefully read the instructions before operating the unit.
• This appliance is for indoor use only.
• his unit must only be connected to a 220-240V / 50Hz earthed outlet.
•  Installation must be in accordance with the regulations of the country where the unit is used.
•  If you are in any doubt about the suitability of your electrical supply, have it checked and, if necessary, modified by a qualified electrician.
• This air purifier has been tested and is safe to use. However, as with any electrical appliance use it with care.
• Disconnect the air purifier from the socket when changing the filters or cleaning the unit.
• Avoid touching any moving parts of the appliance.
• Never insert fingers, pencils or any other objects through the guard.
• This device is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities. It is also not intended for use by those with a lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.
•  Do not leave children unsupervised with this device.
• Do not clean the unit by spraying it or immersing it in water. Use a damp cloth only.
  Never allow water or vapors to enter the unit.
• Do not clean with strong chemical agents or other abrasive materials.
• Never connect the unit to an electrical outlet using an extension cord. If a power outlet is not available, one should be installed by a qualified electrician.
• Never operate this appliance if the cord or power supply are damaged. Ensure the power cord is not stretched or exposed to sharp objects/edges.
• A damaged power supply should be replaced by the manufacturer. Never extend or attempt to change the power supply lead.
• Any service other than a regular cleaning or filter replacement should be performed by an authorized service representative. Failure to comply could result in a voided warranty.
• Do not use the appliance for any other purposes than its intended use.
• Avoid removing the power cord from the socket whilst the unit is still in operation. This could cause electrical damage.
• Never use the power supply as a switch to start and turn off the air purifier unit. Use the provided ON/OFF switch located on the control panel.
• Always place the unit on a dry and stable surface.
• The use of accessory attachments that have not been approved by the appliance the manufacturer is not recommended, as this may result in fire, cause an electric shock and
  or cause personal injury.
• Ensure hands are fully dried before plugging or unplugging the appliance.
• The appliance should not be installed in the laundry or wet rooms.

Energy Saving and Unit Safety Protection Tips

• Do not cover or restrict the airflow from the outlet or inlet grills.
• For maximum performance and safety, the minimum distance from a wall or objects should be 20cm. Keep away from other electrical appliances.
• Keep the filters clean. Under normal conditions, filters should only need cleaning once every two weeks (approximately). Since the filters remove airborne particles, more frequent cleaning may be necessary, depending on the air quality.EAP120HC provides 5 stages of air purification using professional air filtration and intelligent sterilization technologies. This unit features advanced all-in-one dual photocatalytic HEPA and an activated carbon filter for improved air filtration.

– Primary filters, made of non-woven materials, are used for removing large particles like hair and dust.
– Antibacterial HEPA filter to remove 99.9% of airborne particles of 0.25 micrometers or larger.
– Activated carbon filter removes unpleasant odors and absorbs harmful substances such as formaldehyde and benzenes.
– Photocatalytic filter with molecular sieve adsorption layer removes smaller particles and decompose further the pollutants.
– Plasma Ioniser sterilizes even further and removes mold spores and allergens from the air.
The EAP120HC also features an air quality LED indicator that will help in monitoring the quality of the air.

Applications:
– Personal use in domestic and office space to improve air quality
– Helps smokers to minimize the effects of smoking
– Helps asthma and pollen sufferers
– Great for children’s rooms and small offices
NOTE: This air purifier is not a substitute for proper ventilation, regular vacuum cleaning or for the use of a cooker hood whilst cooking. If the humidity is over 60% Relative  Humidity we recommend using a dehumidifier to reduce the humidity.

Air Purifier Features and Indoor Pollutants

VOC (Volatile Organic Compound) – VOCs come from motor vehicle exhausts, gasoline vapor, pollutants such as formaldehyde, ammonia, and many other common and chemical solvents such as paints and glues, or can be a by-product of mold growth. VOCs cause irritation to the eyes and or nose as well as causing headaches, nausea, and even potential damage to the central nervous system. Pressed wood furniture, newly decorated rooms, paint, and cleaning solvents are common sources of VOCs.
Mold / Fungus – these can affect our respiratory system and cause allergic reactions, like a runny nose, eye and throat irritation, headaches, fatigue, and aggravation of asthma.
Other indoor pollutants include – bacteria, viruses, dust mites, and pollen, etc.
Emissions from electronic office equipment – Many studies, including those from EPA and the University of California Berkley, have reported that emissions from office equipment like computers and printers, including VOCs, ultra-fine particles, and ozone.
These emissions have been proven to have a negative effect on the health of many people which can be reduced by busing an air purifier.
Using HEPA filters, Activated Carbon filters, and Plasma Ionisation – An effective HEPA filter is absolutely necessary to remove particles, even at a microscopic level; it ensures that the particles are not spread. Plasma Ionisers will sterilize the air and reduce bacterial growth.
The antibacterial activated carbon on the EAP120HC is a natural material biosynthesized from the walnut shell, the adsorption area of activated carbon is very large up to 300,000
square meters. The activated carbon filter will absorb unpleasant odors and reduce the VOC content in the air.
The Plasma Ioniser will sterilize the air and reduce bacterial growth.

Operation

1. Unpack the appliance and remove the filter cover:
2. Remove the filter and plastic bag: connect it to the DC socket on the bottom:
3. Load 2 composite filters and close the cover:
4. Remove the plug adapter and How to Use:
5. Connect the plug to an earthed socket:
   

Press the ON/OFF button to turn the unit on. Press again to turn it off.
Pressing the Ioniser button will activate the ionizer function. Press again to turn it off.
With the unit powered on, press the TIMER button to select the automatic off time. Press repeatedly to select 2, 4 or 8 hours.
With the unit powered off, press the TIMER button to select the automatic start time. Press repeatedly to select 2, 4 or 8 hours.
Alter the fan speed by pressing the SPEED button. Select from Medium or High.
The AIR QUALITY indicator will be illuminated blue if air quality is good.
It will be red if the air quality is poor.
Changing the Filter 
Open the filter cover by pressing in the retaining tabs and pulling the cover free. Remove the old filters by simply pulling on the tabs to release then.
Replace the filters with new/clean ones and replace the filter cover.

Diagram of Air Purifier

Composite filter

Diagram of Air Purifier

Care and Maintenance

• Always shut off the unit and unplug from the mains before cleaning or performing any maintenance.
• When the unit is not in use for long periods, it is advisable to remove the plug from the power socket.
• Do not use chemical solvents (such as benzene, alcohol, or gasoline) as they may cause irreversible damage to the unit.

Cleaning the Case

• Only use tepid water and a mild detergent on a soft cloth.
• Do not use bleach or abrasives.
• Do not splash water directly onto the main unit.
• Avoid wetting the power connection port, doing so may cause an electric shock and can lead to the insulation deteriorating or unit rusting.

Cleaning the Filters and Filter Holding Area

•  Hoover the filter gently every 2-3 weeks or more often if used in a dustier environment.
•  Make sure the filter is not damaged during the process and replace if it does become damaged.
• Wipe the filter holding area with a dry cloth if necessary.

Clean the filter Cover and Clean Air Outlet

• Use water and a mild detergent.
•  Do not use bleach or abrasives.
•  Do not spray water inside the unit.
• If the clean air outlet grilles get soiled easily, use a vacuum attachment or soft brush to clean.
• If the filter cover is dirty, hoover it. If it is heavily soiled, wash it with warm
  soapy water and dry thoroughly before reinserting it in the unit.

NOTE: Do no assemble the unit and power it on before all the parts are completely dry. Any other maintenance other than what is described in this user manual must be only performed by the service center.

Technical Specification & Troubleshooting

Technical Specification

Troubleshooting

Disposal

Disposal: Do not dispose of this product as unsorted waste. Collection of such waste must be handled separately as special treatment is necessary. Recycling facilities are now available for all customers at which you can deposit your old electrical products. Customers will be able to take any old electrical equipment to participate sites run by their local councils. Please remember that this equipment will be further handled during the recycling process, so please be considerate when depositing your equipment. Please contact the local council for details of your local household waste recycling centers.

ElectrIQ UK SUPPORT
www.ElectrIQ.co.uk/support
Please, for your own convenience, check the troubleshooting guide before calling the service line.
If the unit still fails to operate call: 0871 620
1057 or complete the online form
Office hours: 9 AM – 5 PM Monday to Friday

www.ElectriQ.co.uk
Unit 2, The Nursery
Bristow Lane
South Normanton
Derbyshire, DE55 2FX