DUMOR Stackable Frame Kit

Open the box and make sure you have all the parts in the list:

PARTS LIST

Part#	Description	Image	Quantity
1	Verical Frame Legs		4 pcs
2	Horizontal Dropping Pan Supports		2 pcs
3	Stacking Lugs		4 pcs (only used if stacking for more cages)
4	Nuts & Bolts		12 NUTS and 12 BOLTS

1. Remove top of already assembled cage
   
2. Lay the cage on its side and attach the vertical frame legs to the two horizontal plates on each side of the cage. There should be an extra hole at the bottom of the vertical frame leg that will be used to attach the horizontal dropping pan supports. Secure with two nuts and bolts per side. The head of the bolt will be on the outside of the cage.
   
3. Repeat step 2 for the remaining legs.
   
4. Gently, flip the cage upside down and attach the horizontal dropping pan supports on the inside of the vertical frame legs. Bolt the supports through the vertical frame legs from the same direction as the vertical frame legs.
   
5. Put the cage upright and place the top panel on the cage, then secure the top panel with the hooks on all 4 sides same as when attached side panels.. Slide the tray into the tray supporters underneath the cage.
   
6. You can stack 2 cages on top of each other using the four stacking lugs.
   

Distributed by:
TRACTOR SUPPLY COMPANY
5401 VIRGINIA WAY
BRENTWOOD, TN 37027
For customer support,
call: 1-888-376-9601
www.TractorSupply.com
MADE IN VIETNAM

Sku# 1110263
DuMor Rabbit Hutch Assembly Manual

Distributed by:
TRACTOR SUPPLY COMPANY
5401 VIRGINIA WAY,
BRENTWOOD, TN 37027
For customer support, call: 1-888-376-9601
www.TractorSupply.com
MADE IN CHINA

PARTS LIST

Part	Image	Description	Quantity
1		24” Cage	1 pc
2		24” Plastic Tray	1pc
3		Galvanized Feeder	1pc
4		Water Bottle	1pc
5		Frame Legs 24in	4pcs
6		Cross Rod	2pcs
7		Stacking Lugs	4pcs
8		Screw& Nuts	12 sets

ASSEMBLY INSTRUCTION

Step 1. Rabbit Cage Set Up

1. Remove your new DuMor rabbit cage from box and set on flat surface. The door located on the front panel must be locked in a closed position to keep it secured during assembly. (Figure A)

2. Unfold front and back panel’s completely and set it on the ground.(Figure B)

Step 2. Frame Legs Set Up
1. Position one frame leg on the side of the cage so that the top of the leg is aligned with the top of the cage and the bottom of the leg extends4-3/4” past the bottom of the cage. Line up holes in frame leg with holes in leg mounting bracket. (Figure C)

2. Push the screw through the upper hole in the leg from outside of the cage. Put a nut onto the screw and tighten .Repeat for the other three legs.
3. Turn the cage upright so that the bottom now faces downward. The cage bottom should be approximately 4-3/4″ off the ground. (Figure D)

4. Fold the front (door panel) and back panel up to the inside of the cage and pull back into panel clips on the top and sides. Bend tab on panel clips slightly to  fully secure in place. (Figure E)

5.Next, install the tray rails by positioning them just below the cage and secure in place with provided screws and nuts. (Figure F)

Step 3. Rabbit tray& Feeder & Water Bottle Set Up
1. The tray can now slide onto the rail and will have approximately 1-1/2″ of clearance beneath it. (Figure G)

2. To install the rabbit feeder, a small opening must be cut in the side of the cage. The bottom chute of the feeder requires a 2″x6″opening. (Figure H)

3. Determine the desired placement of the feeder. It should be low enough so it can be reached comfortably.
4. With small wire cutters (not supplied), cut two adjacent horizontal wires and two adjacent vertical wires close to the outer wires. This yields a 2″x6″ opening. Be  sure to down the sharp ends left by the cutting. Fit the bottom spout of the feeder through the opening and using the wire clips built into the feeder, attach the feeder to the side. (Figure I)

5. Determine the proper height of the nozzle for your pet.
6. Hang the water bottle supports at appropriate upper wire.
7. Fill the bottle and secure the lid and attached nozzle.
8. Place water bottle nozzle down in water bottle supports. The bottle must be completely vertical to allow proper nozzle ball seating, in order to prevent leaks. (Figure J)