CAT CJ1000DCP Jump Starter and Compressor

CAT CJ1000DCP Jump Starter and Compressor

THIS QUICK START GUIDE IS NOT A SUBSTITUTE FOR THE INSTRUCTION MANUAL. PLEASE REFER  TO THE INSTRUCTION MANUAL AND YOUR VEHICLE’S USER’S MANUAL BEFORE USE.

IMPORTANT CHARGING INSTRUCTIONS

1. Immediately charge this unit for a full 40 hours upon receipt. This unit’s internal battery is shipped in a partially charged state and must be fully charged before use.
2. Fully charge the unit immediately after purchase, every 30 days, and after each use. Lead-acid batteries can lose charge over time. Regular recharging can optimize performance and battery life.

DIGITAL DISPLAY

ICON	SOLID	FLASHING
	Unit is fully charged	Unit is charging
	USB power is ON
	Compressor feature has been selected	Compressor feature is ON
	Vehicle has started	Ready to Jump-start
		System fault detected*
	Correct Clamp connection
	Reverse Clamp connection

• Consult the TROUBLESHOOTING section of the Instruction Manual for further info.

REVERSE POLARITY ALARM

When battery clamps are connected in reverse polarity, an audible alarm (continuous beep) will sound and the LCD screen will display the Reverse Polarity Indicator icon (please see Instruction Manual for details). DO NOT activate the jump starter. If this happens carefully disconnect the clamps and re-connect with the proper polarity. Ensure that the grounded clamp has a firm and clean connection.

USING THE AIR COMPRESSOR

To prevent overheating, Air Compressor will automatically shut off after 10 minutes. Please allow a 30-minute cooldown before resuming inflation. Note that the Air Compressor will store the last PSI setting in memory, making it easier to regularly top off your vehicle’s tires.

USB POWER

1. Press the USB button on the control panel.
2. Plug the electronic device into any of the USB Ports and operate normally.
3. LCD Screen will display Voltage Indicator and USB Power On icon.

©2020 Caterpillar. CAT, CATERPILLAR, BUILT FOR IT, their respective logos, “Caterpillar Yellow,” “Caterpillar Corporate Yellow,” the “Power Edge” trade dress as well as corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission. ONE YEAR LIMITED WARRANTY: This product is covered by a one (1) year limited warranty. See the instruction manual for full details. TO REDUCE THE RISK OF INJURY, THE USER MUST READ THE INSTRUCTION  MANUAL. The product in this box may differ slightly from that pictured. Not all objects are included. Baccus  Global, a licensee of Caterpillar Inc. US Patent No. D761,200. *Sure Fit® is a registered US trademark and Set & Forget™ is a  US trademark owned by Baccus Global LLC. This unit was designed for household use only.

FAQ’S

How do I charge the unit?

The unit can be charged by connecting an AC power source to the DC input port on the back of the unit.

How long will it take to charge?

It will take approximately 40 hours to fully charge a completely discharged unit.

How long will a full charge last?

A fully charged battery should provide enough power to start an average size vehicle up to 20 times. If you are using the compressor, it will reduce the number of jump-starts you can do before recharging.

How long does it take to recharge?

It takes approximately 10 hours to recharge a completely discharged unit.

What is reverse polarity alarm and what should I do if I hear it?

When battery clamps are connected in reverse polarity, an audible alarm (continuous beep) will sound and the LCD screen will display the Reverse Polarity Indicator icon (please see Instruction Manual for details). DO NOT activate the jump starter. If this happens carefully disconnect the clamps and reconnect them properly. If this happens again, please contact your authorized service center or call Customer Service at 1-800-732-6839 for assistance.

How do I charge my cat jump starter?

CHARGING/RECHARGING
Open the AC adapter cover located on the back of the unit and connect an extension cord to the unit. Plug the other end of the cord into a standard 120-volt AC wall outlet.
Charge until the green LED Battery Status Indicator lights solid.
Once fully charged, disconnect the extension cord.

Can a jump starter charge a battery?

A jump pack — a more conveniently designed portable jump-starting device — is the modern solution for how to charge a dead battery in your car. You can even use them on your own, without the need for another person or connecting to a running vehicle.

How many volts is a car battery?

12.6 volts
When we take a closer look, we see car battery voltage can range anywhere from 12.6 to 14.4. With the engine off, the fully charged car battery voltage will measure 12.6 volts. This is known as “resting voltage.” When the engine is running, battery voltage will typically rise to 13.5 to 14.5 volts.

Where is the reset button on a generator?

Reset Breaker for Power Tech Generators. Reset breakers are located on the control box of your generator along with the main on/off switch and main breakers. Reset breakers protect the circuit from surges. When your generator experiences a surge, these breakers need to be pushed in to be reset.

How long does cat jump starter battery last?

Typically as a general rule 24 – 48 hours immediately after purchase and after every use. It is also recommended to recharge every 30 – 60 days for approximately 12 hours or until the battery status indicators show full when the product is not in use.

How do you know when a jump starter is fully charged?

Usually an indicator light on the jump starter tells you when a recharge is necessary. Simply insert the power adapter into an outlet and charge the battery until the light indicates a complete charge.

What does 1000 peak amps mean?

Generally speaking, a jump starter with a higher peak amp rating is more powerful than one with a lower peak amp rating. Peak amps typically ranger from 300 to 1000 amps with some very powerful ones exceptionally reaching over 3000 amp.

CAT CJ1000DCP Jump Starter and Compressor
www://catautopower.com/

330 GC HYDRAULIC EXCAVATOR

NEXT GENERATION EXCAVATORS

Cat® Next Generation Excavators offer you more choices than ever for your business.

• MORE MODEL OPTIONS
• MORE STANDARD TECHNOLOGIES
• MORE PRICE POINTS

Ready to help you make your business stronger, Cat Next Generation Excavators give you ways to get the most work done at the lowest cost – so you put more money in your pocket.

THE CAT 330 GC offers you the ideal balance of dependable performance, operator productivity features, and reduced costs. The Cat 330 GC is a smart choice for operations where high reliability and low-cost-per-hour performance are priorities.

REDUCE FUEL CONSUMPTION UP TO 12%1

The precise combination of larger hydraulic pumps, an electronic main control valve, and electronically controlled cooling fans delivers top performance while burning less fuel.

WORK SMART. SAVE MONEY.

The Cat 330 GC is equipped with two modes to help manage fuel consumption for your specific applications – Power Mode and Smart Mode.
Power Mode delivers maximum productivity in high demand applications like truck loading and trenching.
Smart Mode automatically matches engine speed and hydraulic power to demand for the highest fuel efficiency in any application.
Operators can set and store their power mode preference using Operator ID. Owners can lock in the mode they want their operators to use to help manage fuel consumption.

FUEL SAVINGS ADD UP.

The Next Generation Cat 330 GC uses up to 12% less fuel than the 330F.

THE NEXT GENERATION CAT 330 GC

USES 4400 L (1,160 GAL) LESS FUEL PER YEAR COMPARED TO THE CAT 330F.

SCENARIO:

Based on 2,000 labor hours per year.
330F (AVERAGE): 18 L (4.8 GAL) PER HOUR × 2,000 HOURS/YEAR = 36 000 L (9,510 GAL) PER YEAR. NEXT GENERATION 330 GC: 15.8 L (4.2 GAL) PER HOUR × 2,000 HOURS/YEAR = 31 600 L (8,350 GAL) PER YEAR; 36 000 L (9,510 GAL) PER YEAR – 31 600 L (8,350 GAL) PER YEAR = 4400 L (1,160 GAL) PER YEAR.

THE HARD OUT OF WORK

Sites where excavators typically work are rugged and challenging. That’s why it’s important that the 330 GC cab protects the operator as much as possible from the fatigue, stresses, sounds, and temperatures of the job.

ISO-CERTIFIED ROPS CAB

The ISO-certified ROPS cab is sound suppressed and sealed. The windows and lower front, right, and rear profile of the machine give outstanding visibility to the work area without the strain of constantly leaning forward.

ALL-AROUND VISIBILITY

Large windows at the front, sides, and rear give excellent visibility in all directions from the operator seat. The ROPS structure uses narrow front cab pillars to allow a wider field of view to the front. Plus, with the standard rearview and right-side cameras, operators will always be aware of what’s surrounding the excavator.

EASY ACCESS, CONNECTIVITY, AND STORAGE

Several built-in convenience features make work more comfortable for operators:

• Bluetooth® integrated radio
• USB ports for charging and phone connectivity
• 12V DC outlets and AUX port
• Storage in rear, overhead, and console compartments
• Cup and bottle holders

Specification

CUSTOMIZABLE JOYSTICKS

Joystick function can be customized through the monitor. Joystick pattern as well as response can be set to match operator preferences. All preferences are saved with the Operator ID and restored at login.

TOUCHSCREEN MONITOR

Most machine settings can be controlled through the high-resolution 203 mm/8-inch touchscreen monitor. It offers 42 languages and is easy to reach from the seat – no twisting or turning to reach switches. A handy jog dial control and shortcut keys are also ergonomically positioned on the right console.

SEAT AND CONSOLE

Efficiency of movement is critical to keeping operators productive and alert all shift long. The 330 GC seat is designed for easy operation and comfort. The standard seat is wide and adjustable so operators of any size can work comfortably.

KEYLESS PUSH START

The 330 GC uses a keyless push-button engine start. This adds security for the machine by using Operator ID codes to limit and track machine access. Codes can be entered manually, via an optional Bluetooth key fob, or a smartphone app.

LOWER MAINTENANCE COSTS UP TO 25%

With synchronized and extended maintenance intervals, you get more done at a lower cost compared to the 330F. Consolidated filter locations make service faster. Hydraulic, air, and fuel tank filters have increased capacity and longer life. Access to the operation and maintenance manual is easy through the in-cab monitor.

KEY MAINTENANCE COST REDUCTIONS INCLUDE:

• Consolidated filter locations to reduce service time.
• Improved hydraulic filter with higher dirt holding capacity.
• Oil and fuel filters with extended maintenance intervals.
• Advanced Cat air filter with double the dust holding capacity of the previous filter.
• High-efficiency electric cooling fans only run when needed and reverse to keep cores free from debris. Choose between manual and auto reverse fan settings.

LESS RISK. MORE REWARD

REDUCED CHANCE OF LEAKS AND DAMAGE WITH
FEWER CONNECTIONS AND LESS HOSE.

SAFETY FEATURES

LOOK OUT FOR YOUR PEOPLE AND YOUR EQUIPMENT

Keep your people and your equipment safe with upper platform access, a ground level engine oil dipstick, and secure start system on the Cat 330 excavator

UPPER PLATFORM ACCESS

Access the upper platform from the entry point on the right side of the machine. The additional steps and handrails provide added support.

GROUND-LEVEL DAILYMAINTENANCE

All daily maintenance checks can be performed from ground level, making maintenance faster, easier, and safer. Checkpoints include the engine oil dipstick, fuel water separator, fuel tank water and sediment drains, and cooling system coolant level check.

SECURE START

Use your PIN code on the monitor, the optional Bluetooth key fob, or your smartphone to enable the push-button starting feature.

CAT LINK TECHNOLOGY

TAKES THE GUESSWORK OUT OF MANAGING YOUR EQUIPMENT

CAT LINK telematics technology helps take the complexity out of managing your jobsites – by gathering data generated by your equipment, materials, and people and serving it up to you in customizable formats.

PRODUCT LINK™
Product Link™ collects data automatically and accurately from your assets – any type and any brand. Information such as location, hours, fuel usage, productivity, idle time, maintenance alerts, diagnostic codes, and machine health can be viewed online through web and mobile applications.

VISIONLINK®
Access information anytime, anywhere with VisionLink® – and use it to make informed decisions that boost productivity, lower costs, simplify maintenance, and improve safety and security on your jobsite. With different subscription level options, your Cat dealer can help you configure exactly what you need to connect your fleet and manage your business without paying for extras you don’t want. Subscriptions are available with cellular or satellite reporting (or both).
Caterpillar releases products, services, and technologies in each region at different time intervals. Please verify with your local Cat dealer for technology availability and specifications.

INCREASE YOUR PRODUCTIVITY AND PROFIT WITH CAT ATTACHMENTS

You can easily expand the performance of your machine by utilizing any of the variety of Cat Attachments. Each Cat Attachment is designed to fit the weight and horsepower of Cat Excavators for improved performance, safety, and stability.

ATTACHMENTS

BUCKETS

GRAPPLES

HYDRAULIC HAMMERS

MULTI-PROCESSORS

QUICK COUPLERS

RAKES

RIPPERS

SECONDARY PULVERIZERS

SHEARS

THUMBS

VIBRATORY PLATE COMPACTORS

TECHNICAL SPECIFICATIONS

ENGINE

Engine Model:  Cat C7.1
Engine Power – ISO 9249:  151 kW 202 hp
Engine Power – ISO 14396:  152 kW 204 hp
Bore:  105 mm 4 in
Stroke:  135 mm 5 in
Displacement:  7.01 L 428 in3

Net Power is tested per ISO 9259. Standards in effect at the time of manufacture.
Net power advertised is the power available at the flywheel when the engine is equipped with fan, air intake system, exhaust system and alternator.
Rated speed at 2,200 rpm.

HYDRAULIC

Main System – Maximum Flow (Implement):  560 L/min 148 gal/min
Maximum Pressure – Equipment:  35 000 kPa 5,075 psi
Maximum Pressure – Travel:  35 000 kPa 5,075 psi
Maximum Pressure – Swing:  2 8 400 kPa 4,120 psi

SWING MECHANISM

Swing Speed:  11.5 rpm
Maximum Swing Torque:  105 kN·m 77,370 lbf-ft

WEIGHTS

Operating Weight* 30 600 kg 67,460 lb
*Long Undercarriage, Reach Boom, R3.2 (10’6″) Stick, HD 1.54 m3 (2.01 yd3) bucket and 800 mm (31″) triple grouser shoes.
Operating Weight* 29 600 kg 65,255 lb *Long Undercarriage, Reach Boom, R3.2 (10’6″) Stick, HD 1.54 m3 (2.01 yd3) bucket and 600 mm (24″) triple grouser shoes.

SERVICE REFILL CAPACITIES

Fuel Tank:  474 L 125.2 gal
Cooling System:  25 L 6.6 gal
Engine Oil:  25 L 6.6 gal
Swing Drive:  10 L 2.6 gal
Final Drive (each):  5.5 L 1.5 gal
Hydraulic System (including tank):  310 L 81.9 gal
Hydraulic Tank:  147 L 38.8 gal
DEF Tank:  41 L 10.8 gal

AIR CONDITIONING SYSTEM

The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430).
The system contains 0.9 kg of refrigerant, which has a CO2 equivalent of 1287 metric tonnes.

DIMENSIONS

Boom Reach: 6.15 m (20’2″)
Stick Reach:  3.2 m (10’6″)
Bucket HD:  1.54 m3 (2.01 yd3

Shipping Height (top of cab):  3050 mm 10’0″
Handrail Height:  3050 mm 10’0″
Shipping Length:  10 420 mm 34’2″
Tail Swing Radius:  3130 mm 10’3″
Track Length to Center of Rollers – Standard Undercarriage*:  3490 mm 11’5″
Track Length to Center of Rollers – Long Undercarriage:  3990 mm 13’1″
Ground Clearance:  490 mm 1’7″
Track Gauge – Standard Undercarriage*:  2390 mm 7’10”
Track Gauge – Long Undercarriage:  2590 mm 8’6″
Transport Width – 600 mm (24″) Shoes, Standard Undercarriage*: 2990 mm 9’10”
Transport Width – 600 mm (24″) Shoes, Long Undercarriage:  3190 mm 10’6″
Transport Width – 800 mm (31″) Shoes, Standard Undercarriage*:  3190 mm 10’6″
Transport Width – 800 mm (31″) Shoes, Long Undercarriage:  3390 mm 11’1″
Counterweight Clearance 1110 mm 3’8

WORKING RANGES AND FORCES

Boom:  Reach 6.15 m (20’2″)
Stick:  Reach 3.2 m (10’6″)
Bucket:  HD 1.54 m3 (2.01 yd3)
Maximum Digging Depth:  7260 mm 23’10”
Maximum Reach at Ground Level:  10 690 mm 35’1″
Maximum Cutting Height:  10 020 mm 32’11”
Maximum Loading Height:  6940 mm 22’9″
Minimum Loading Height:  2280 mm 7’6″
Maximum Depth Cut for 2440 mm (8′) Level Bottom: 7100 mm 23’4″
Maximum Vertical Wall Digging Depth:  6030 mm 19’9″
Bucket Digging Force (ISO):  179 kN 40,200 lbf
Stick Digging Force (ISO):  126 kN 28,300 lbf

STANDARD & OPTIONAL EQUIPMENT

Standard and optional equipment may vary. Consult your Cat dealer for details.

CAB

ROPS, standard sound suppression STANDARD
Mechanically adjustable seat STANDARD
High-resolution 203 mm (8 in) LCD touchscreen monitor STANDARD

CAT TECHNOLOGY

Cat Product Link  STANDARD
Auto Hammer Stop  STANDARD

ENGINE

Two selectable power modes  STANDARD
Auto engine speed control  STANDARD
Auto engine idle shutdown  STANDARD
52° C (125° F) high-ambient cooling capacity  STANDARD
–32° C (–25° F) cold start capability  OPTIONAL
Double element air filter with integrated precleaner  STANDARD
Reversing electric cooling fans  STANDARD
Biodiesel capability up to B20  STANDARD

HYDRAULIC SYSTEM

Boom and stick regeneration circuits  STANDARD
Auto warm up  STANDARD
Auto two-speed travel  STANDARD
Boom and stick drift reduction valve  STANDARD
Boom and stick lowering check valves  OPTIONAL
Hammer return filter circuit  OPTIONAL
Advanced Tool Control (two pump, one/two way high-pressure flow)  STANDARD
Medium-pressure circuit  STANDARD
Quick coupler circuit  STANDARD
*Europe only  STANDARD

BOOM AND STICKS

6.15 m (20’2″) reach boom, 3.75 m (12’4″) reach stick  OPTIONAL
6.15 m (20’2″) reach boom, 3.2 m (10’6″) reach stick  OPTIONAL
6.15 m (20’2″) reach boom, 2.65 m (8’8″) reach stick  OPTIONAL

UNDERCARRIAGE AND STRUCTURES

600 mm (24″) triple grouser shoes  OPTIONAL
800 mm (31″) triple grouser shoes  OPTIONAL
Tie-down points on base frame  STANDARD
6700 kg (14,770 lb) counterweight (all regions except Japan)  STANDARD
5800 kg (12,790 lb) counterweight (Japan only)  STANDARD

ELECTRICAL SYSTEM

Two 1,000 CCA maintenance free batteries  STANDARD
Programmable time-delay LED working lights  STANDARD
LED chassis light, left-hand/right-hand boom lights, cab lights  STANDARD

SERVICE AND MAINTENANCE

Scheduled Oil Sampling (S·O·SSM) ports  STANDARD
Ground-level and platform-level engine oil dipsticks  STANDARD
Electric refueling pump with auto shutoff  OPTIONAL

SAFETY AND SECURITY

Rearview camera  STANDARD
Right-hand-sideview camera  STANDARD
Ground-level engine shutoff switch  STANDARD
Right-hand handrail and handhold  STANDARD
Signaling/warning horn  STANDARD

Cat® 307.5 Mini Hydraulic Excavator

Features:

The Cat® 307.5 Mini Excavator delivers maximum power and performance in a mini size to help you work in a wide range of applications.

ALL DAY COMFORT

• A sealed and pressurized cab is equipped with an improved air conditioning system, adjustable wrist rests and a suspension seat to help keep you working comfortably all day long.

EASY TO OPERATE

• Controls are easy to use and the intuitive Next Generation Monitor provides customizable machine operator preferences and easy to read machine information.

STICK STEER TRAVEL MODE

• Moving around the job site is even easier with Cat Stick Steer. Easily switch from traditional travel controls with levers and pedals to joystick controls with a push of a button. The benefit of less effort and improved control is in your hands!

BIG PERFORMANCE IN A MINI DESIGN

• Increased lifting, swinging, travel and multi-functioning performance helps you get the job done more efficiently, and blade float allows for easy grading.

SAFETY ON THE JOB SITE

• Your safety is our top priority. The Cat Mini Excavator is designed to help keep you safe on the job. A back-up camera, courtesy work  light sand a fluorescent retractable seat belt are just a few of the safety features we’ve built into the machine.

SIMPLE SERVICE FOR LESS DOWNTIME

• Maintenance is quick and easy on the Cat Mini Excavator. Routine check points are easy to access at ground level with grouped service points and robust service panels.

LOWER OPERATING COSTS

• Equipped with features such as auto idle, auto engine shutdown, and efficient hydraulics with a variable displacement pump, the Cat Mini Excavator was designed with reducing your operating costs in mind.

UNMATCHED DEALER SUPPORT

• Your Cat dealer is here to help you reach your business goals. From providing equipment solutions to operator training to service needs and beyond, your Cat dealer is ready to help.

Specifications

Engine

Engine Model: Cat C2.4 Turbo

Rated Net Power @ 2,400 rpm

U.S. EPA Tier 4 Final/EU Stage V
ISO 9249/EEC 80/1269               40.9 kW        54.8 hp

Gross Power

SAE J1995:   43.2 kW        57.9 hp
Bore:   87 mm      3.4 in
Stroke:   102.4 mm     4 in
Displacement:   2.43 L   148 in3

Weights

Minimum Operating Weight with Cab*        7505 kg 16,549 lb
Maximum Operating Weight with Cab**       8120 kg 17,905 lb

**Minimum Weight is based on steel tracks, no counterweight, operator, full fuel tank, standard stick, blade and no bucket.
**Maximum Weight is based on steel tracks with rubber pads, counterweight, operator, full fuel tank, long stick, blade and no bucket.

Weight Increase from Minimum Configuration

Counterweight:                250 kg        552 lb
Long Stick:                       82 kg         181 lb
Steel Tracks with Pads:     285 kg       628 lb

Travel System

Travel Speed – High 5.0 km/h 3.1 mph
Travel Speed – Low 3.1 km/h 1.9 mph
Maximum Traction Force – High Speed 26.1 kN 5,856 lb
Maximum Traction Force – Low Speed 62.4 kN 14,035 lb
Ground Pressure – Minimum Weight 34.8 kPa 5.1 psi
Ground Pressure – Maximum Weight 37.7 kPa 5.5 psi
Gradeability (maximum) 30 degrees

Service Refill Capacities

Cooling System 10 L 2.6 gal
Engine Oil 9.5 L 2.5 gal
Fuel Tank 145 L 38 gal
Hydraulic Tank 53 L 14 gal
Hydraulic System 110 L 29 gal

Hydraulic System

Load Sensing Hydraulics with Variable Displacement Piston Pump
Pump Flow @ 2,400 rpm 167 L/min 44 gal/min
Operating Pressure – Equipment 285 bar 4,134 psi
Operating Pressure – Travel 285 bar 4,134 psi
Operating Pressure – Swing 250 bar 3,626 psi
Maximum Auxiliary Circuit – Primary
Flow at Pump* 131 L/min 35 gal/min
Pressure at Pump* 285 bar 4,134 psi
Maximum Auxiliary Circuit – Secondary
Flow at Pump* 33 L/min 9 gal/min
Pressure at Pump* 285 bar 4,134 psi
Digging Force – Stick (standard) 37.8 kN 8,504 lb
Digging Force – Stick (long) 33.7 kN 7,579 lb
Digging Force – Bucket 54.6 kN 12,272 lb

*Flow and pressure are not combinable. Under load, as flow rises pressure goes down.

Swing System

Machine Swing Speed 10 rpm

Blade

Width 2280 mm 90 in
Height 431 mm 17 in

Certification – Cab

Roll Over Protective Structure (ROPS) ISO 12117-2:2008
Tip Over Protective Structure (TOPS) ISO 12117:1997
Top Guard ISO 10262:1998 (Level I)

Sound

Operator Sound Pressure 72 dB(A)
(ISO 6396:2008)
Average Exterior Sound Pressure 98 dB(A)
(ISO 6395:2008)

• European Union Directive “2000/14/EC”

Air Conditioning System

The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains .90 kg of refrigerant which has a CO2 equivalent of 1.287 metric tonnes.

Lift Capacities – Minimum Configuration

Cat® 307.5 Mini Hydraulic Excavator

Features:

The Cat® 307.5 Mini Excavator delivers maximum power and performance in a mini size to help you work in a wide range of applications.

ALL DAY COMFORT

• A sealed and pressurized cab is equipped with an improved air conditioning system, adjustable wrist rests and a suspension seat to help keep you working comfortably all day long.

EASY TO OPERATE

• Controls are easy to use and the intuitive Next Generation Monitor provides customizable machine operator preferences and easy to read machine information.

STICK STEER TRAVEL MODE

• Moving around the job site is even easier with Cat Stick Steer. Easily switch from traditional travel controls with levers and pedals to joystick controls with a push of a button. The benefit of less effort and improved control is in your hands!

BIG PERFORMANCE IN A MINI DESIGN

• Increased lifting, swinging, travel and multi-functioning performance helps you get the job done more efficiently, and blade float allows for easy grading.

SAFETY ON THE JOB SITE

• Your safety is our top priority. The Cat Mini Excavator is designed to help keep you safe on the job. A back-up camera, courtesy work  light sand a fluorescent retractable seat belt are just a few of the safety features we’ve built into the machine.

SIMPLE SERVICE FOR LESS DOWNTIME

• Maintenance is quick and easy on the Cat Mini Excavator. Routine check points are easy to access at ground level with grouped service points and robust service panels.

LOWER OPERATING COSTS

• Equipped with features such as auto idle, auto engine shutdown, and efficient hydraulics with a variable displacement pump, the Cat Mini Excavator was designed with reducing your operating costs in mind.

UNMATCHED DEALER SUPPORT

• Your Cat dealer is here to help you reach your business goals. From providing equipment solutions to operator training to service needs and beyond, your Cat dealer is ready to help.

Specifications

Engine

Engine Model: Cat C2.4 Turbo

Rated Net Power @ 2,400 rpm

U.S. EPA Tier 4 Final/EU Stage V
ISO 9249/EEC 80/1269               40.9 kW        54.8 hp

Gross Power

SAE J1995:   43.2 kW        57.9 hp
Bore:   87 mm      3.4 in
Stroke:   102.4 mm     4 in
Displacement:   2.43 L   148 in3

Weights

Minimum Operating Weight with Cab*        7505 kg 16,549 lb
Maximum Operating Weight with Cab**       8120 kg 17,905 lb

**Minimum Weight is based on steel tracks, no counterweight, operator, full fuel tank, standard stick, blade and no bucket.
**Maximum Weight is based on steel tracks with rubber pads, counterweight, operator, full fuel tank, long stick, blade and no bucket.

Weight Increase from Minimum Configuration

Counterweight:                250 kg        552 lb
Long Stick:                       82 kg         181 lb
Steel Tracks with Pads:     285 kg       628 lb

Travel System

Travel Speed – High 5.0 km/h 3.1 mph
Travel Speed – Low 3.1 km/h 1.9 mph
Maximum Traction Force – High Speed 26.1 kN 5,856 lb
Maximum Traction Force – Low Speed 62.4 kN 14,035 lb
Ground Pressure – Minimum Weight 34.8 kPa 5.1 psi
Ground Pressure – Maximum Weight 37.7 kPa 5.5 psi
Gradeability (maximum) 30 degrees

Service Refill Capacities

Cooling System 10 L 2.6 gal
Engine Oil 9.5 L 2.5 gal
Fuel Tank 145 L 38 gal
Hydraulic Tank 53 L 14 gal
Hydraulic System 110 L 29 gal

Hydraulic System

Load Sensing Hydraulics with Variable Displacement Piston Pump
Pump Flow @ 2,400 rpm 167 L/min 44 gal/min
Operating Pressure – Equipment 285 bar 4,134 psi
Operating Pressure – Travel 285 bar 4,134 psi
Operating Pressure – Swing 250 bar 3,626 psi
Maximum Auxiliary Circuit – Primary
Flow at Pump* 131 L/min 35 gal/min
Pressure at Pump* 285 bar 4,134 psi
Maximum Auxiliary Circuit – Secondary
Flow at Pump* 33 L/min 9 gal/min
Pressure at Pump* 285 bar 4,134 psi
Digging Force – Stick (standard) 37.8 kN 8,504 lb
Digging Force – Stick (long) 33.7 kN 7,579 lb
Digging Force – Bucket 54.6 kN 12,272 lb

*Flow and pressure are not combinable. Under load, as flow rises pressure goes down.

Swing System

Machine Swing Speed 10 rpm

Blade

Width 2280 mm 90 in
Height 431 mm 17 in

Certification – Cab

Roll Over Protective Structure (ROPS) ISO 12117-2:2008
Tip Over Protective Structure (TOPS) ISO 12117:1997
Top Guard ISO 10262:1998 (Level I)

Sound

Operator Sound Pressure 72 dB(A)
(ISO 6396:2008)
Average Exterior Sound Pressure 98 dB(A)
(ISO 6395:2008)

• European Union Directive “2000/14/EC”

Air Conditioning System

The air conditioning system on this machine contains the fluorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains .90 kg of refrigerant which has a CO2 equivalent of 1.287 metric tonnes.

Lift Capacities – Minimum Configuration

Standard and Optional Equipment

Standard and optional equipment may vary. Consult your Cat dealer for details.

ENGINE

Cat C2.4 Diesel Engine (U.S. EPA Tier 4 Final/EU Stage V) – Electronic Engine, Turbo, Diesel Particulate Filter (DPF)  Standard
Automatic Engine Idle  Standard
Automatic Engine Shutdown  Standard
Automatic Swing Brake  Standard
Automatic Two Speed Travel  Standard
Fuel Water Separator with Indicator  Standard
Radial Seal – Double Element Air Filter  Standard
Extended Life Coolant, –37° C ( –37° F)  Standard

HYDRAULICS

Smart Tech Electronic Pump  Standard
Variable Displacement Piston Pump  Standard
Load Sensing/Flow Sharing Hydraulics  Standard
Power On Demand  Standard
Hydraulic Temperature Monitoring  Standard
Certified Accumulator  Standard
HYDO Advanced Hydraulic Oil  Standard

OPERATOR ENVIRONMENT

Top Guard ISO 10262 1998 Level I  Standard
ROPS ISO 12117-2:2008  Standard
Stick Steer Mode  Standard
Travel Cruise Control  Standard
Control Pattern Changer  Standard
Adjustable Wrist Rests  Standard
Molded Footrests  Standard
Removable, Washable Floor Mat  Standard
Travel Pedals and Hand Levers  Standard
Cat Key with Passcode Option  Standard
HVAC with Automatic Temperature Control  Standard
Hydraulic Lockout Controls  Standard
Integrated Lower Front Window  Standard
Assisted Front Window Overhead Storage  Standard
Rear Window Emergency Exit  Standard
Fabric, High Back, Suspension Seat  Standard
Air Suspension Heated Seat  Standard
Retractable Seat Belt (75 mm/3 in)  Standard
Coat Hook  Standard
Cup Holder  Standard
LED Interior Light  Standard
Literature Holder  Standard
Mounting Bosses for Top and Front Guards  Standard
12V Power Socket  Standard
Radio – Bluetooth®, Auxiliary, Microphone, USB (charging only)  Standard
Skylight  Standard
Signaling/Warning Horn  Standard
Cab and (left side) Boom Work Lights  Standard
Utility Space for Mobile Phone  Standard
Rain Visor  Standard
Next Generation Color LCD Monitor (IP66)  Standard
– Jog Dial Interface (cab machines only)  Standard
– Fuel Level and Coolant Temperature Gauges  Standard
– Maintenance and Machine Monitoring  Standard
– Performance and Machine Adjustments  Standard
– Numeric Security Code  Standard
– Multiple Languages  Standard
– Camera Ready (IP68 & IP69K)  Standard
– Hour Meter with Wake Up Switch  Standard

OPERATOR ENVIRONMENT (CONTINUED)

Next Generation Advanced Monitor (below are all included with Next Generation Advanced Monitor option)  Optional
– Jog Dial Control Interface
– Touch Screen
– Site Reference System
– High Definition Camera Capable (IP68 & IP69K)

UNDERCARRIAGE

Greased and Lubricated Track  Standard
Tie Down Eyes on Track Frame  Standard
Dozer Straight Blade  Standard
Dozer Float  Standard
Bolt-on, Reversible Wear Edge  Standard
Steel Tracks (450 mm/17.7 in wide)  Optional
Wide Steel Tracks (600 mm/23.6 in)  Optional
Steel Track with Rubber Pads  Optional
Track Guides  Optional

BOOM, STICK AND LINKAGES

One Piece Boom (3700 mm/145.7 in)  Standard
Standard Stick (1665 mm/65.6 in)  Standard
Long Stick (2200 mm/86.6 in)  Optional
Front Shovel Capable – Pin-on/Manual Coupler/Hydraulic Coupler for Cat Tools  Standard
Thumb Ready (not available in all regions)  Standard
Attachments including Buckets, Augers and Hammers  Optional
2nd Auxiliary Hydraulic Lines  Optional
Boom Lowering Check Valve  Optional
Stick Lowering Check Valve  Optional
Bucket Linkage with Lift Eye  Optional
Certified Lifting Eye (optional in some regions)  Standard

ELECTRICAL

12 Volt Electrical System  Standard
90 Ampere Alternator  Standard
900 CCA Maintenance Free Battery  Standard
Battery Disconnect  Standard
Ignition Key Stop Switch  Standard
Product Link™ Basic (regulations apply) Standard
Product Link Elite (regulations apply)  Optional
Travel Alarm  Standard
Rearview Camera  Optional
Rotating Beacon  Optional

GUARDING

Heavy Duty Front Guard ISO 10262 1998 Level II  Optional
Mesh Front Guard ISO 10262 1998 Level I  Optional
Overhead Cab Guard ISO 10262 1998 Level II  Optional
Polycarbonate Front Window EN356 P5A (Cab Only)  Optional
Track Guards  Optional

OTHER

Locks on External Enclosure Doors  Standard
Lockable Fuel Cap  Standard
Beacon Socket  Standard
Rear Reflectors  Standard
Water Jacket Heater  Optional
Refueling Pump  Optional

M318 WHEELED EXCAVATOR

NEXT GENERATION WHEELED EXCAVATORS

The new wheeled excavators match your performance needs to bring you:

• LOWER OPERATING AND MAINTENANCE COSTS
• INCREASED OPERATOR EFFICIENCY AND VISIBILITY
• MORE IN-CAB COMFORT

DO MORE WORK WITH EXTENDED INTERVALS

MAXIMIZE PERFORMANCE:

Work faster with up to 14% more swing torque with lower fuel and DEF consumption. Tiltrotator integration gives you more versatility to complete more tasks faster with one machine.

ENHANCED CAB COMFORT:

Operate comfortably with the ergonomic control layout and cab options. Get better visibility with rear and side view cameras and an optional 360-degree machine view system.

UP TO 10% MAINTENANCE SAVINGS

Fewer maintenance costs, combined with 100% daily ground-level maintenance and extended service intervals, increase uptime and keep overall costs down.

CAT LINK TECHNOLOGY

TAKES THE GUESSWORK OUT OF MANAGING YOUR EQUIPMENT

Cat Link telematics technology helps take the complexity out of managing your jobsites by gathering data generated by your equipment, materials, and people and serving it up to you in customizable formats.

PRODUCT LINK™
Product Link collects data automatically and accurately from your assets – any type and any brand. Information such as location, hours, fuel usage, productivity, idle time, maintenance alerts, diagnostic codes, and machine health can be viewed online through web and mobile applications.

VISIONLINK®
Access information anytime, anywhere with VisionLink. Use it to make informed decisions that boost productivity, lower costs, simplify maintenance, and improve safety and security on your job site. With different subscription level options, your Cat dealer can help you configure exactly what you need to connect your fleet and manage your business without paying for extras you don’t want. Subscriptions are available with cellular or satellite reporting (or both).

Remote Services is a suite of technologies that improve your jobsite effi ciency.
Remote Troubleshoot allows your Cat dealer to perform diagnostic testing on your connected machine remotely, pinpointing potential issues while the machine is in operation. Remote Troubleshoot helps ensure the technician arrives with the correct parts and tools the fi rst time, eliminating additional trips to save you time and money.
Remote Flash updates on-board software without a technician being present, potentially reducing update time by as much as 50 percent. You can initiate the update when convenient, increasing your overall operating effi ciency.
The Cat App helps you manage your assets – at any time – right from your smartphone. You can see your fl eet location, hours, and other information. You will get critical alerts for required maintenance, and you can even request service from your local Cat dealer.

Get in and out of the cab more easily with the tilt-up left console. Deluxe and Premium cab options offer supreme comfort, from a heated/cooled seat to automatic temperature control.

ERGONOMIC CONTROL LAYOUT

Controls are positioned to reduce fatigue and straining movements to help keep you operating at your full potential.

REDUCED CAB VIBRATIONS

Feel more comfortable in the cab while you work with reduced cab vibrations from advanced viscous mounts.

BLUETOOTH® CONNECTION

Bluetooth® integrated radio allows for seamless mobile phone connection to listen to music, podcasts, and hands-free calling.

LONGER SERVICE INTERVALS

The in-cab monitor tracks fi lter life and machine intervals, so you always know when it’s time for regular machine service.

GROUND LEVEL ACCESS

Complete your daily machine checks entirely from the ground, minimizing the need to access the upper platform.

NEW FILTERS

Two levels of filtration protect your engine from dirty diesel. The new hydraulic oil filter improves filtration performance and lasts up to 50 percent longer than previous filter designs.

SAVE UP TO 10% IN MAINTENANCE COSTS

KEYLESS PUSH START

Start the engine with the push-to-start button or using the unique Operator ID function.

MACHINE SETTINGS

Access the operator manual at your fingertips as well as the power mode selector to keep productivity while using less fuel.

JOYSTICK PREFERENCES

Program your preferred power mode and joystick preferences with your Operator ID. Once you enter in your Operator ID, the excavator remembers your settings each time

TOUCHSCREEN MONITOR

Use the standard 254 mm (10-in) touchscreen monitor to adjust your heating/cooling setting for more comfort or to view your machine information.

LOOK OUT FOR YOUR PEOPLE AND YOUR EQUIPMENT SAFETY FEATURES

Stay Safe Every Day

Daily maintenance checks can be performed with 100% of the points accessible from ground level, making maintenance faster, easier, and safer. Standard LED lights gives you a better view of your jobsite.

• ENJOY BETTER VISIBILITY INTO TRENCHES, IN EACH SWING DIRECTION, AND BEHIND YOU. THE SMALLER CAB PILLARS, LARGER WINDOWS, AND A FLAT ENGINE HOOD DESIGN LOWER OBSTRUCTION TO YOUR VIEW. REAR VIEW AND SIDE VIEW CAMERAS ARE STANDARD, AND THE 360 DEGREE VIEW SYSTEM OPTION OFFERS A HIGHER VIEWING VANTAGE POINT OF THE MACHINE. .
• THE STANDARD SOUND SUPPRESSION ROPS CAB MEETS ISO 12117-2:2008 REQUIREMENTS AND HELPS TO BLOCK THE NOISE TO STAY FOCUSED ON THE JOB.
• THE SERVICE PLATFORM DESIGN PROVIDES EASY, SAFE, AND QUICK ACCESS TO UPPER PLATFORM. THE STEPS USE ANTI-SKID PUNCH PLATES TO PREVENT SLIPPING.
• THE AUTO AXLE LOCK PRESSES THE PEDAL FOR YOU TO REDUCE YOUR OVERALL NUMBER OF ACTIONS. THE MACHINE AUTOMATICALLY DETECTS WHEN THE SERVICE BRAKE AND AXLE NEED TO BE LOCKED OR UNLOCKED. IT RELEASES AUTOMATICALLY WHEN YOU PRESS THE TRAVEL PEDAL.

INCREASE PRODUCTIVITY AND VERSATILITY WITH CAT ATTACHMENTS
You can easily expand the performance of your machine by utilizing any of the variety of Cat Attachments. Each Cat Attachment is designed to fi t the weight and horsepower of Cat wheeled excavators for improved performance, safety, and stability

ATTACHMENTS

BUCKETS

GRAPPLES

HYDRAULIC HAMMERS

QUICK COUPLER

SHEARS

VIBRATORY PLATE COMPACTORS

MULCHERS*

TILTROTATOR*

PIN GRABBER COUPLER*

TECHNICAL SPECIFICATIONS

See cat.com for complete specifi cations.

ENGINE

Engine Model: Catsd C4.4
Engine Power – ISO 14396:  129 kW 174 hp
Engine Power – ISO 14396 (metric):  176 hp (PS)
Bore:  105 mm 4 in
Stroke:  127 mm 5 in
Displacement:  4.4 L 268.5 in3

• Meets U.S. EPA Tier 4 Final, EU Stage V, and Korea Tier 4 Final emission standards and Blue Angel Certifi ed.
• Net power advertised is the power available at the fl ywheel when engine is equipped with fan, air cleaner, CEM exhaust gas after treatment, alternator, and cooling fan running at intermediate speed.
• Recommended for use up to 3000 m (9,843 ft) altitude with engine power derating above 3000 m (9,843 ft).
• Rated speed 2,200 rpm.

HYDRAULIC SYSTEM

Main System – Maximum Flow:  254 L/min 67 gal/min
Maximum Pressure – Equipment:  37 000 kPa 5,366 psi
Maximum Pressure – Travel:  35 000 kPa 5,076 psi
Maximum Pressure – Swing:  35 500 kPa 5,149 psi

SWING MECHANISM

Swing Speed:  9.4 rpm
Maximum Swing Torque:  44kN·m 32,560 lbf-ft

WEIGHTS

Operating Weight Minimum:  17 500 kg 38,580 lb
Operating Weight Maximum:  19 950 kg 43,980 lb

• Operating weight includes full fuel tank, operator, bucket 610 kg (1,340 lb), and dual pneumatic tires. Weight varies depending on configuration. Typical configurations include 2500 mm (8’2″) medium stick and 3700 kg (8,157 lb) counterweight.

SERVICE REFILL CAPACITIES

Fuel Tank:  350 L 92.5 gal
Cooling System:  32 L 8.5 gal
Engine Oil:  11 L 2.9 gal
Diesel Exhaust Fluid (DEF) Tank:  20 L 5.3 gal
Final Drive:  2.5 L 0.7 gal
Hydraulic System (including tank):  260 L 68.7 gal
Hydraulic Tank:  120 L 31.7 gal

DIMENSIONS

Boom Reach:  5250 mm (17′ 1″)
Stick Reach:  2500 mm (8′ 2″)
Bucket GD:  0.91 m3 (1.19 yd3)
Shipping Height (top of cab):  3360 mm 11′
Support Point:  3520 mm 11′ 7″
Shipping Length:  8470 mm 27′ 9″
Tail Swing Radius:  2350 mm 7′ 9″
Counterweight Clearance:  1301 mm 4′ 3″
Ground Clearance:  325 mm 1′ 1″
Undercarriage Length:  4440 mm 14′ 7″
Wheel Base:  2700 mm 8′ 10″

WORKING RANGES AND FORCES

Boom Type:  VA Boom
Stick:  Reach 2500 mm (8’2″)
Bucket GD:  0.91 m3 (1.19 yd3)
Loading Height:  7300 mm 23′ 11″
Cutting Height:  10 260 mm 33′ 8″
Digging Height:  5890 mm 19′ 4″
Reach at Ground Level:  9210 mm 30′ 3″
Vertical Wall Digging Depth:  4600 mm 15′ 1″
Bucket Forces (ISO):  119 kN 26,752 lbf
Stick Forces (ISO):  75 kN 16,861 lbf

• Range values are with dual pneumatic tires (10.00-20).
• Range values are calculated with a GD bucket (CW) and CW-30 quick coupler with a tip radius of 1484 mm (4’10”).
• Force values are calculated with heavy lift on, a GD bucket (pin-on), and a tip radius of 1378 mm (4’6″).

AIR CONDITIONING SYSTEM

• The air conditioning system on this machine contains the fl uorinated greenhouse gas refrigerant R134a (Global Warming Potential = 1430). The system contains 0.85 kg of refrigerant which has a CO2 equivalent of 1.216 metric tonnes.

STANDARD & OPTIONAL EQUIPMENT

Standard and optional equipment may vary. Consult your Cat dealer for details.

CAB

ROPS, sound suppression  STANDARD
Keyless push-to-start engine control  STANDARD
Deluxe Cab  OPTIONAL
Premium Cab  OPTIONAL
High-Resolution 254 mm (10 in) LCD
touchscreen monitor STANDARD

CAT TECHNOLOGIES

Product Link STANDARD
Remote Flash/Troubleshoot Capability STANDARD

ENGINE

Power mode selector  STANDARD
One-touch low idle with auto engine speed control  STANDARD
Auto engine idle shutdown  STANDARD
52°C (125°F) high-ambient cooling capacity  STANDARD
-18°C (0°F) cold start capability  STANDARD 
Double element air filter with integrated precleaner  STANDARD
Biodiesel capability up to B20  STANDARD
On-demand electric cooling fans with auto reverse function  STANDARD
Electric priming pump  STANDARD
Ride control  OPTIONAL
Separate dedicated swing pump  STANDARD

HYDRAULIC SYSTEM

Auto hydraulic warmup  STANDARD
Automatic swing brake  STANDARD
Boom and stick drift reduction valve STANDARD
Electronic main control valve  STANDARD
Slider joysticks (2 types)  OPTIONAL
Boom/stick lowering check valves  OPTIONAL
SmartBoom™  OPTIONAL
Cat TRS support  OPTIONAL
Joystick steering  OPTIONAL
Combined fl ow/high-pressure auxiliary circuit  OPTIONAL
Quick coupler circuit  OPTIONAL
Ride control  OPTIONAL
Separate dedicated swing pump  STANDARD

SAFETY AND SECURITY

Rear and right-side-view cameras  STANDARD
360° visibility  OPTIONAL
Wide angle mirrors  STANDARD
Ground-level engine shutoff switch  STANDARD
Handrail and hand holds on service platform  STANDARD
Signaling/warning horn  STANDARD

BOOM AND STICKS

5100 mm (16’9”) One-piece boom  OPTIONAL
5250 mm (17’1”) variable adjustable boom  OPTIONAL
2200 mm (7’3”) stick1  OPTIONAL
2500 mm (8’2”) stick  OPTIONAL
2900 mm (9’6”) stick  OPTIONAL

UNDERCARRIAGE AND STRUCTURES

10.00-20 16 PR, dual tires  OPTIONAL
315/70R22.5, no gap dual tires  OPTIONAL
445/70R 19.5, single tires OPTIONAL
All-wheel drive  STANDARD
Automatic brake/axle lock  STANDARD
3700 kg (8,157 lb) counterweight  OPTIONAL
4200 kg (9,259 lb) counterweight  OPTIONAL
Fenders  OPTIONAL

ELECTRICAL SYSTEM

LED lights on boom and cab  STANDARD
Roading and indicator lights, front and rear  STANDARD
Maintenance-free batteries  STANDARD
Centralized electrical disconnect switch  STANDARD
LED chassis light, left-hand/right-hand  STANDARD
boom lights, cab lights  OPTIONAL
Electrical refueling pump  OPTIONAL

SERVICE AND MAINTENANCE

Sampling ports for Scheduled Oil Sampling (S•O•SSM)  STANDARD
Ground-level and platform-level engine oil dipsticks  STANDARD
Automatic lubrication system for implement  and swing system  OPTIONAL
Ground-level engine shutoff switch  STANDARD
Anti-skid plate  STANDARD
Signaling/warning horn  STANDARD
Rotating beacon  OPTIONAL

All regions except North America