BLACK DIAMOND SPOT R 400 LED Headlamp Instruction Manual

IMPORTANT: Follow all instructions carefully and keep for future reference.

BATTERY – RECHARGEABLE LITHIUM-ION

Charging: 

• Charge the battery completely before initial use.
• Battery does not need to be fully discharged prior to being recharged.
• Battery will automatically stop charging when fully charged.

Battery Life: Your battery life will vary depending on:

• “Recovery time” or time when lamp has not been on.
• Temperature.
• Settings used.
• A full charge is needed to achieve maximum burn time!
• Dispose of the device/batteries in accordance with applicable local laws and regulations.

ANSI FL-1 Standard: Runtime to 10% of initial output.
Reserve: Additional time the lamp will produce usable light for low intensity activities (measured to .25 Lux @ 4 meters.)

USE / MODES

STORAGE AND TRANSPORTATION

CARE AND MAINTENANCE

TROUBLESHOOTING

If the product does not work:

• Charge the batteries completely
• Check that the USB cord is properly inserted

No luck? Contact your Black Diamond Dealer or
www.BlackDiamondEquipment.com.

 WARNINGS

• A responsible adult must supervise use by children under the age of 12
• Inspect your headlamp for proper operation prior to using and, for critical situations, carry a second light and sufficient spare batteries
• Do not stare directly into the beam or shine it directly into others’ eyes. Intense light can damage your eyes or the eyes of those around you. Black Diamond Equipment is not responsible for the consequences, whether direct, indirect or accidental, or for any other type of damage arising or resulting from the use of its products.

LIMITED WARRANTY

We warrant for three years from purchase date and only to the original retail buyer (Buyer) that our lighting products (Products) are free from defects in material and workmanship. We do not warrant Products against normal wear and tear, improper use, or improper maintenance. If Buyer discovers a covered defect, Buyer should return the Product to the place of purchase. In the event that this is not possible, return the Product to us at the address provided. The Product will be repaired or replaced at our discretion. That is the extent of our liability under this Warranty and, upon expiration of the applicable warranty period, all such liability shall terminate. We reserve the right to require proof of purchase for all warranty claims. This Warranty gives you specific rights, and you may also have other rights which vary from state to state. Except for expressly stated in this Warranty, we shall not be liable for direct, indirect, incidental, or other types of damages arising out of, or resulting from the use of Product. This Warranty is in lieu of all other warranties, express or implied, including, but not limited to, implied warranties of merchantability or fitness for a particular purpose (some states do not allow the exclusion or limitation of incidental or consequential damages or allow limitations on the duration of an implied warranty, so the above exclusions may not apply to you).

This Black Diamond product meets the requirements of the EMC (electromagnetic compatibility) Directive 2014/30/EU and the RoHS Directive 2011/65/EU. It also meets the requirements for Electromagnetic Compatibility Regulations 2016 and The Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012 as brought into UK law.

The Declarations of Conformity for this product may be viewed at
www.blackdiamondequipment.com/DOC

NOTE: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product generates, uses and can radiate radio frequency energy and, if not used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the product does cause harmful interference to radio, television, cell phone or avalanche beacon reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Increase the separation between the product and receiver.
• Turn the product off or to a different setting.

Industry Canada ICES-005 Compliance Label: CAN ICES-005 (B)/ NMB-005 (B)

 
North America: Black Diamond Equipment, Ltd.
2084 East 3900 South
Salt Lake City, UT 84124

Europe: Black Diamond Europe
Hans-Maier-Straße 9
6020, Innsbruck, Austria

 www.BlackDiamondEquipment.com

© Black Diamond Equipment, Ltd. 2022

This product is protected by one or more of the following patents. Other patents pending.

REV 20210429

or visit black-diamond.com
Mid-States Distributing, LLC., 2800 Meacham Blvd., Fort Worth, TX 76137 USA

INTRODUCTION

Congratulations on your purchase of a Black Diamond product. Black Diamond designs, builds and supports all of our products to strict specifications and guidelines. With proper product knowledge, safe use, and regular maintenance, this product should bring years of satisfying service. Every effort has been made to ensure the accuracy and completeness of the information in this manual at the time of publication, and we reserve the right to change, alter and/or improve the product and this document at any time without prior notice.
Black Diamond highly values how our products are designed, manufactured, operated, and serviced as well as providing safety to the operator and those around the generator.  Therefore, it is IMPORTANT to review this product manual and other product materials thoroughly and be fully aware and knowledgeable of the assembly, operation, dangers and maintenance of the product before use. Fully familiarize yourself, and make sure others who plan on operating the product fully familiarize themselves too, with the proper safety and operating procedures before each use. Please always exercise common sense and always err on the side of caution when operating the product to ensure no accident,  property damage, or injury occurs. We want you to continue to use and be satisfied with your Black Diamond product for years to come.
When contacting Black Diamond/Champion Power Equipment about parts and/or services, you will need to supply the complete model and serial numbers of your product.  Transcribe the information found on your product’s data plate label to the table below.

BLACK DIAMOND TECHNICAL SUPPORT TEAM
1-888-373-8272
MODEL NUMBER: BD201097
SERIAL NUMBER
DATE OF PURCHASE
PURCHASE LOCATION

SAFETY DEFINITIONS
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and their explanations, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper accident prevention measures.

DANGER
DANGER indicates a hazardous situation that, if not avoided, will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE indicates information considered important, but not hazard-related (e.g., messages relating to property damage).

CONTROLS AND FEATUrES

CAUTION
The wheel kit is not intended for over-the-road use.

Parts Included

ASSEMBLY

Your wheel kit requires assembly. For questions regarding the assembly of your wheel kit, call our helpline at 1-888-373-8272. Please have your model number available.

Drain oil and fuel before assembly. Failure to drain before assembly can result in oil and fuel leaking onto the generator and ground. Oil and fuel will also drain into the carburetor and engine requiring to disassemble to clean out.

Install Wheels

1. Tip generator up onto non-marring surface with panel side up.
2. Insert Large Roll Pin (B) through Wheel (A) from the outside.
3.  Insert the Large Roll Pin through the wheel bracket on the generator frame.
4. Insert Large R-clip (C) into the hole on the end of Large Roll Pin.
5. Repeat for the second wheel.
6. Tip generator back down.

Install the Support Leg

1. Tip generator up onto non-marring surface with alternator/ muffler side up.
2. Attach Support Leg (D) to generator frame with Flange Bolt (E) and Flange Lock Nut (F).
3. Tip generator back down so resting on wheels and support legs.

Install the handle

1. Place Handle (G) inside the handle mounting brackets on the frame.
2. Insert Small Roll Pin (H) into the hole on the frame and through the Handle and handle mounting bracket.
3. Insert Small R-clip (I) into the hole on the end of Small Roll Pin (H).
4. Repeat on another side.

Add Engine Oil
See Operator’s Manual for filling the engine with oil.
Add Fuel
See Operator’s Manual for filling the engine with fuel.

Not refilling engine oil after the wheel kit is assembled will damage the engine and void the warranty.

PARTS DIAGrAM

WARRANTY

CHAMPION POWER EQUIPMENT
1 YEAR LIMITED WARRANTY
Warranty Qualifications
To register your product for warranty and FREE lifetime call center technical support please visit: https://www.championpowerequipment.com/register
To complete registration you will need to include a copy of the purchase receipt as proof of the original purchase. Proof of purchase is required for warranty service. Please register within ten (10) days from date of purchase.
Repair/Replacement Warranty
CPE warrants to the original purchaser that the mechanical and electrical components will be free of defects in material and workmanship for a period of one year (parts and labor) from the original date of purchase and 90 days (parts and labor) for commercial and industrial use. Transportation charges on products submitted for repair or replacement under this warranty are the sole responsibility of the purchaser. This warranty only applies to the original purchaser and is not transferable.

Do Not return The  Unit To The Place Of Purchase
Contact CPE’s Technical Service and CPE will troubleshoot any issue via phone or e-mail. If the problem is not corrected by this method, CPE  will, at its option, authorize evaluation, repair or replacement of the defective part or component at a CPE Service Center. CPE will provide you with a case number for warranty service. Please keep it for future reference. Repairs or replacements without prior authorization, or at an unauthorized repair facility, will not be covered by this warranty.

Warranty Exclusions
This warranty does not cover the following repairs and equipment:
Normal Wear
Products with mechanical and electrical components need periodic parts and services to perform well. This warranty does not cover repair when normal use has exhausted the life of a part or the equipment as a whole.
Installation, Use and Maintenance 
This warranty will not apply to parts and/or labor if the product is deemed to have been misused, neglected, involved in an accident, abused, loaded beyond the product’s limits,  modified, installed improperly or connected incorrectly to any electrical component. Normal maintenance is not covered by this warranty and is not required to be performed at a facility or by a person authorized by CPE.

Other Exclusions
This warranty excludes:

• Cosmetic defects such as paint, decals, etc.
• Wear items such as filter elements, o-rings, etc.
• Accessory parts such as starting batteries, and storage covers.
• Failures are due to acts of God and other force majeure events beyond the manufacturer’s control.
• Problems caused by parts that are not original Champion
  Power Equipment parts.

Limits of Implied Warranty and Consequential Damage 

Champion Power Equipment disclaims any obligation to cover any loss of time, use of this product, freight, or any incidental or consequential claim by anyone from using this product. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR  FITNESS FOR A PARTICULAR PURPOSE.
A unit provided as an exchange will be subject to the warranty of the original unit. The length of the warranty governing the exchanged unit will remain calculated by reference to the purchase date of the original unit.
This warranty gives you certain legal rights which may change from state to state or province to province. Your state or province may also have other rights you may be entitled to that are not listed within this warranty.

Contact Information
Address
Mid-States Distributing, LLC.
2800 Meacham Blvd.
Fort Worth, TX 76137 USA
www.black-diamond.com
Customer Service
Toll-Free: 1-888-373-8272
info@black-diamond.com