Better Non-Illuminated Bathroom Mirror and Furniture

INSTALLATION TOOLS

PARTS LIST

INSTALLATION – Check the product for damage prior to installation

Before any drilling is carried out, please check for pipes and wires within the wall which could be damaged.

MIRROR INSTALLATION

Fitted to the rear of the unit are x 2 fixing brackets, measure the distance between the two brackets and mark this distance on the wall, ensuring this horizontally aligned, using a spirit level. We recommend a height for the brackets of 70” (1778mm) from the floor, but this is customer choice.
It is recommended to install to a solid wall, but if fitting to a stud wall, the fixings must be secured into a stud, not only into the plasterboard.

After the position of the brackets is marked, drill the holes in the wall, using an 8mm drill bit (not supplied), to a depth of approx 40mm.

Insert the wall plugs and tap flush with the wall surface.

Hold the bracket up to the wall over the drilled holes and secure using the screws provided.

Ensure the brackets on the rear of the unit are fully tightened.

Lift the product on the wall mounted brackets to engage both sections of the brackets.

Once installed a bead of silicone can be applied around the edges of the unit if required.

CABINET INSTALLATION

Fitted to the rear of the unit are x 2 fixing brackets, measure the distance between the two brackets and mark this distance on the wall, ensuring this horizontally aligned, using a spirit level.

We recommend a height for the brackets of 27.5” (698mm) from the floor, but this is customer choice.

It is recommended to install to a solid wall, but if fitting to a stud wall, the fixings must be secured into a stud, not only into the plasterboard.

It is also recommended to set up the unit before installing the basin not the unit, so any adjustment can be made, via the fixings on the unit.

After the position of the brackets is marked, drill the holes in the wall, using an 8mm drill bit (not supplied), to a depth of approx 40mm.

Insert the wall plugs and tap flush with the wall surface and secure the wall brackets into place.

Check the brackets fitted to the unit are fully tightened. Lift the unit onto wall fitted brackets.

If any adjustment forward or backward / up or down is required this is possible via the fitted adjusters on the inside of the unit.

After any adjustment of the unit has been made the basin can be fitted to the unit, by applying a bead of silicone between the unit and basin to provide a seal and fixing for the basin to the unit.
Also run a bead of silicone along the back edge of the base where it meets the wall.

DOOR HANDLE INSTALLATION

The doors which are to be fitted with handles, either the round or shell type are provided with pilot holes which should be drilled to allow fitting of the handle screw through the door and into the handle.

Drill the holes, then place the screw through the unit from inside the door, connect this to the handle and tighten.

FRAMED FURNITURE ASSEMBLY

Place the frame onto the unit and screw the frame to the unit through the holes in the frame, ensuring this is aligned with the unit edge.

Ensure this is fully secured before use.

WC UNIT INSTALLATION

• Drill into the wall through the rear plinth of the WC unit.
• Fit the wall plug
• Place the screw through the washers and secure to the wall.
• Fit brass screw cap to brass washer

WC UNIT INSTALLATION

CLEANING AND MAINTENANCE

Wipe the product clean and dry regularly, especially when the product is subject to steam or splashes.

Do not use harsh chemicals or materials on the product, as this will damage the product and invalidate your guarantee.

To clean and maintain the product, wipe using a clean damp cloth and wipe dry with a soft cloth.

UK SUPPORT
Call: 0871 244 0935
Office hours: 9am – 5pm Monday to Friday
www.BetterBathrooms.com
Unit J6, Lowfields Business Park, Lowfields Way, Elland, West Yorkshire, HX5 9DA

Installation and Maintenance

PLEASE READ THIS INSTRUCTION GUIDE FULLY PRIOR TO COMMENCING ANY PART OF THE INSTALLATION.
Please fully check the product for damage and that all parts are present prior to installation.

1. Push the pan into the required position ensuring full connection to the soil pipe, so this will give the finished pan position.
2. Mark the outside edge of the pan in line with the holes in the side of the pan, for the fixing position.
3. Lift away pan and measure the base thickness, mark this dimension in from the previous mark.
   Ensure the floor is level before commencing the installation.
4. Place the L shaped brackets (If supplied) over the marks.
5. Dependant on floor type, drill on the marks for the fixture position Check for pipes and wires prior to drilling.
6. Insert screw plugs if required for your floor type, place washers over the screw and secure bracket into position. Please note the design of the inlet and syphon are for illustration purposes only and may vary depending on the product.
7. Place syphon with rubber washer into the cistern tank, underneath fit the plastic washer and nut and tighten (do not use grips).
8. Place the inlet valve with rubber washer into the cistern tank, underneath fit washer and nut and tighten (ensure valve does not touch the wall of the tank).
9. Fit cistern bolts and rubber washers into the then place large doughnut washer onto the bottom of the  syphon thread, between the cistern base and pan, place onto the pan and fit nuts to secure. Check the wall for wires and pipes.
10. Some cisterns have fixing holes. If your model allows for this, push the toilet into position, mark the holes on the wall, drill the wall, and fit wall plugs (not supplied) if required.
11. Push to pan into the final position ensuring full connection with the soil pipe.
12. Secure the cistern to the wall using screws and washers (not supplied.
13. When fitting the cistern push button, ensure a 2mm gap between the flush rods and the syphon buttons.
    Also, ensure that the large flush button on the syphon aligns with the large button on the flush.
14. Fit the flush button to the cistern lid, secure using the washer and nut, do not overtighten.
15. With the toilet in its final position, through the holes in the side of the pan, fit the plastic cup, then fit the screw to connect with the L shaped bracket under the toilet.
    Once secured push on the screw cover cap.
16. Following installation and connection of the water supply, turn on the water and check all joints for leaks.
    Test the function of the flush button. Finally, once checks have been carried out, fit the toilet seat.
    
17. With the toilet in its final position, through the holes in the side of the pan, fit the plastic cup, then fit the screw to connect with the L shaped bracket under the toilet. Once secured push on the screw cover cap.

To maintain the surface finish of your product, wipe clean after every use, using a clean damp cloth, a mild detergent mixture can be used.
Do not use abrasive cleaning agents/materials which can strip and scratch the surface, use of these agents/materials can invalidate your guarantee CCPC1 – V1 – MAY 19