Safety precautions

Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure safety, observe all warnings and cautions while using the product.
Cautions for the product

•  Do not subject the product to a strong impact to avoid malfunction.
• Do not disassemble, modify or attempt to repair the product.
• Do not handle the product with wet hands to avoid electric shock or injury.
• Do not store the product under direct sunlight, near heating devices or in a hot, humid, or dusty place.

Notes on use

•  Do not swing or carry the microphone by the cable to prevent the microphone from becoming disconnected or damaged.
•  Do not wind the cable around the rack or allow the cable to become pinched.
• The microphone should be placed on a flat, unobstructed mounting surface.
•  Placing any object on a surface (such as a conference table) before its finish is fully cured may result in damage to the finish.

Using the product

Included accessories

1.  Rubber isolators
2.  Nut
3.  7.6 m (24.9′) Microphone cable (TA3F, XLR-M)

How to mount the product

Table/ceiling hole size (when using isolators)

Table/ceiling hole size (when not using isolators)

Example: Mounting on a table

1. Front-of-mic indicator
2. Rubber isolators
3. Nut
4. Table

Connection procedure

The output connector is an XLR-M type with polarity as shown in the figure below.

1. PIN1 (ground)
2.  PIN2 (hot)
3. PIN3 (cold)

Dimensions

Specifications

• 1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL
• For product improvement, the product is subject to modification without notice.

Polar pattern/Frequency response

Polar pattern

Frequency response

Audio-Technica Corporation
2-46-1 Nishi-Naruse, Machida, Tokyo 194-8666, Japan
www.audio-technica.com
©2021 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com

audio Cardioid Condenser Boundary Microphone User Manual

Safety precautions

Although this product was designed to be used safely, failing to use it correctly may result in an accident. To ensure safety, observe all warnings and cautions while using the product.

Cautions for the product

• Do not subject the product to strong impact to avoid malfunction.
•  Do not disassemble, modify or attempt to repair the product.
•  Do not handle the product with wet hands to avoid electric shock or injury.
• Do not store the product under direct sunlight, near heating devices or in a hot, humid or dusty place.

Notes on use

• Do not swing or pull with the cable connected to the microphone to prevent the microphone from becoming disconnected or damaged.
•  Do not wind the cable around the rack or allow the cable to become pinched.
• The microphone should be placed on a flat, unobstructed mounting surface.
•  Placing any object on a surface (such as a conference table) before its finish   is fully cured may result in damage to the finish.

About splash-proof performance

• The splash-proof specification of this product applies only to the head of the microphone.
•  Although the product has splash-proof capabilities equivalent to IPX4, the screw part and the connector part of the product are not splash-proof.
• If the product is not installed properly, the splash-proof effect will not function properly. Firmly attach the product to the ceiling/table using the included rubber isolators.
•  The splash-proof performance is designed to protect the product if it gets wet  from rain, etc. (equivalent to IPX4). JIS/IEC protection grade IPX4 means that the product is protected against exposure to flying water from all directions.
•  The product cannot be used underwater
•  The product cannot be used in hot and humid places, such as bathrooms.
•  The product is not waterproof. Putting a large amount of water on the  product or submerging the product in water may cause damage.
• The product may not function properly if it becomes wet. Wipe the surface of the product with a dry cloth to remove any moisture, and allow the product to dry thoroughly before use.

Using the product

Included accessories

1. Rubber isolators
    
2. Nut
   
   

How to mount the product

1. Table/ceiling hole size (when using isolators)
   
   (Unit: mm)
2. Table/ceiling hole size (when not using isolators)
   
   (Unit: mm)

Example: Mounting on a table

1. Front-of-mic indicator
2.  Rubber isolators
3.  Nut
4.  Table

Connection procedure

The output connector is an XLR-M type with polarity as shown in the figure below.

1. PIN1 (ground)
2.  PIN2 (hot)
3.  PIN3 (cold)

Dimensions

Specifications

• 1 Pascal = 10 dynes/cm2 = 10 microbars = 94 dB SPL
•  For product improvement, the product is subject to modification without notice.

Polar pattern/Frequency response

• Polar pattern
  
  LEGEND
  
  
• Frequency response
  
  LEGEND
  
  

Audio-Technica Corporation
2-46-1 Nishi-naruse, Machida, Tokyo 194-8666, Japan
www.audio-technica.com
©2021 Audio-Technica Corporation
Global Support Contact: www.at-globalsupport.com