SMART CONTROL HUB
FOR COLOR-CHANGING LIGHTS

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to  Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If  this equipment does cause harmful interference to radio or television reception, which can be determined by  turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of  the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:

1.  This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Required

•  Adequate Wi-Fi coverage reaching to the unit (2.4 GHz networks supported)
• Aquascape Smart Control App (available on iOS or Android App Store)

Installation
• The Aquascape Smart Control Hub is required to power and control Aquascape color-changing lights.
• Connect the light, splitter, or extension to the 5-pin quick-connect fitting attached to the hub (Ex. 1).

NOTE: Each Smart Control Hub can control up to 150-watts of color-changing lights.
NOTE: Multiple Smart Control Hubs can be used to assign multiple colors simultaneously.
NOTE: The Smart Control Hub is weather-resistant, but not waterproof.
Install it off the ground and protected it from the elements.
TRANSFORMER SETUP

• Aquascape color-changing lights are designed to operate on a 12-volt,
  outdoor-rated transformer.
  NOTE: It is recommended to locate the transformer as close to the light fixtures as possible to avoid voltage drops caused by long cable runs.
• Plug the transformer into a GFCI-protected outlet.

PAIRING PROCEDURE

• Plug the Smart Control Hub into an a12-Volt transformer, and the unit will automatically enter pairing mode.
  NOTE: The blinking blue light on the face of the unit indicates the plug is in pairing mode and ready to be connected.
• Download the Aquascape Smart Control App (available on iOS or Android App Store).
• Open the Aquascape Smart Control App and click
  ‘Create New Account’ (Ex. 2).
  NOTE: If you already have an account, log in with your username and password.
• Once logged in, click the three dashes in the upper, right-hand corner of the home screen (Ex. 3).
• Click ‘Add New Device’ (Ex. 4).
• Enter the Wi-Fi network and password for the network to which the unit will connect (Ex. 5).
  NOTE: Adequate Wi-Fi coverage is required (2.4 GHz networks supported)
• Continue to follow on-screen instructions to complete the pairing process.
• To reset the device to factory defaults, press and hold the pairing button for ten seconds and release it when the light begins rapidly flashing (Ex. 6).

Troubleshooting
• Device won’t pair
– Make sure the outlet is receiving power
– Make sure you have adequate wireless coverage to connect the device (2.4 GHz networks supported)
– Reset the device to factory defaults
– Make sure the ground-fault circuit interrupter (GFCI) is not tripped

facebook.com/aquascapeinc
youtube.com/aquascape4
pinterest.com/aquascapeinc

For more information about our company or products, please visit our website at aquascapeinc.com or call us at US (866) 877-6637 CAN (866) 766-3426
©2019 Aquascape, Inc. • All Worldwide Rights Reserved

Aquascape Smart Pond Thermometer User Guide

Product Overview

1. Smart Pond Thermometer
2. Smart Pond Thermometer
3. Low-voltage Transformer

Smart Pond Thermometer Specs

Safety Information

WARNING: It is recommended whenever working in or near water to have all electrical devices plugged into a ground fault interrupter (GFCI) that has been installed by a licensed electrician.

• To reduce the risk of electrical shock or damage to the thermometer, all wiring and junction connections should be made per local codes.
  Requirements may vary depending on usage and location.
• The power cable should be protected at all times to avoid punctures, cuts, bruises, and abrasion.
• Operating the Smart Pond Thermometer outside of the 10-15 volt operating range voids the product warranty

IMPORTANT: Aquascape, Inc. is not responsible for losses, injury, or death resulting from a failure to observe these safety precautions, misuse or abuse of pumps or equipment.

Required

• Low-voltage (12V) transformer (included with #74013)
• For use with the Aquascape Smart Control App
  – Adequate WiFi coverage reaching to the unit (2.4 GHz networks supported)
  – Aquascape Smart Control App (available on iOS or Android App Store)

Installation

• Connect the quick-connect fitting to a 12-volt, outdoor-rated transformer (included with #74013). Then, plug the transformer into a GFCI-protected outlet.
• Place the probe in the pond. It is recommended to place the probe at the bottom of the pond for a more accurate reading.
  NOTE: Press the F/C button on the display to switch the display readout between Fahrenheit and Celsius (Ex.4).

PAIRING PROCEDURE

• Once plugged in, the blinking blue light indicates that the unit is in pairing mode and ready to connect to the app.
• Download the Aquascape Smart Control App (available on iOS or Android App Store).
• Open the app and click ‘Create New Account’ (Ex. 1).
  NOTE: If you already have an account, login with your username and password.
• Once logged in, click the three dashes in the upper, right-hand corner of the home screen (Ex. 2) and click ‘Add New Device’ (Ex. 3).

• Continue to follow the on-screen instructions to complete the pairing process.
  NOTE: Adequate WiFi coverage is required (2.4 GHz networks supported)
• To reset the device to factory defaults, press and hold the F/C Button for ten seconds and release when the blue LED light begins rapidly flashing (Ex. 4).

Maintenance

• To ensure maximum accuracy, occasionally remove any debris or buildup from the probe.
  The probe cover is easily removed by twisting it counterclockwise (Ex. 5).

Troubleshooting

• Device won’t pair
  – Make sure the outlet is receiving power and the GFCI is not tripped
  – Ensure adequate wireless coverage (2.4 GHz networks supported)
  – Make sure the password is correct for the network (case sensitive)
  – Reset the device to factory defaults (press and hold F/C Button for ten seconds)

Replacement Parts

Warranty Information

3 YEAR WARRANTY 

Aquascape warrants that the Smart Pond Thermometer will be free of manufacturing defects for three years from date of purchase. Proof of purchase required. Warranty does not cover damage resulting from negligent handling, misuse, or lack of reasonable maintenance or care. If upon Aquascape’s inspection, product shows evidence of a manufacturing defect, Aquascape’s liability is limited, at Aquascape’s option, to the repair of the defect, replacement of the defective product, or refund of the original purchase price. The warranty excludes costs of labor, removal of product, shipping and expenses related to the installation and re-installation of the product. No liability for loss or damages of any nature or kind, whether arising out of or from the use of the product, whether defective or not defective, is assumed by Aquascape, Inc. or its affiliates. Aquascape shall not be liable for any incidental, consequential, or other damages arising under any theory of law whatsoever.

For more information about our company or products, please visit our website at
aquascapeinc.com or call us at US (866) 877-6637 CAN (866) 766-3426
©2020 Aquascape, Inc. • All Worldwide Rights Reserved