Agri-Fab – UseManuals https://usemanuals.com Owner's manuals for all sorts of products Sun, 25 Jun 2023 11:56:05 +0000 en-US hourly 1 https://wordpress.org/?v=6.7.2 https://usemanuals.com/wp-content/uploads/2025/02/favicon-32x32-2.png Agri-Fab – UseManuals https://usemanuals.com 32 32 Agri-Fab 45-0575 85 lbs. Capacity Push Broadcast Spreader Manual https://usemanuals.com/agri-fab/45-0575-broadcast-spreader/ Sun, 25 Jun 2023 11:56:05 +0000 https://usemanuals.com/?p=123998 Read More...

]]> Agri-Fab 45-0575 85 lbs. Capacity Push Broadcast Spreader Instruction Manual

Parts Description

REF QTY PART NO DESCRIPTION REF QTY PART NO DESCRIPTION
1 2 49449 1” Plug 25 2 47963 Flange Bearing
2 26 47189 1/4” Nylock Hex Nut 26 1 28611 1/2” Axle
3 10 43088 Small Washer 27 1 68491BL3 Frame Assembly
4 1 47141 1/4” Nylon Wing Nut 28 1 69209 Gearbox Assembly
5 2 1543-69 Nylon Washer 29 1 43093 Cotter Pin
6 1 27322BL1 Flow Control Mounting Bracket 30 1 28463BL3 Stand Tube
7 1 24858 Adjustable Stop 31 2 45702G Wheel
8 1 44950 1/4-20 X 3/4” Carriage Bolt 32 2 46699 1/4 X 2” Hex Bolt
9 1 43848 Control Arm Grip 33 5 43648 1/4 X 1-1/2” Hex Bolt
10 1 24856BL1 Control Arm 34 1 45428 Flow Plate
11 1 42347 Torsion Spring 35 1 2-118 Slide Gate Bracket
12 2 43661 1/4-20 X 1” Hex Bolt 36 1 28464BL3 Lower Handle Tube
13 3 1509-69 1/4-20 X 1-3/4” Hex Bolt 37 2 44482 Handle Grip
14 2 44101 3/32” Cotter Pin 38 1 44589BL3 Short Handle Tube
15 1 45431 Control Rod 39 6 43866 Bolt, Hex 1/4-20 X 5/8 GR5
16 1 28662BL3 Handle Tube 40 4 28325 Spacer, .31ID X 5/8 GR5
17 1 48934 Hairpin Agitator 41 1 2-205 Tube, Deflector Frame 85 lb.
18 1 45433ORG Hopper 42 1 2-207 Deflector, Front
19 10 41196 Clamp, 7/32 Bare X 0.28 43 2 2-206 Deflector, Side
20 1 45504 Impeller 44 4 49870 Bolt, Hex 1/4-20 X 2-1/2″
21 4 R19171616 Large Washer 45 2 28486BL1 Support Angle
22 1 44566 Torsion Spring 46 1 45470 Grate
23 1 47063 5/32” Cotter Pin 47 1 40883 Hopper Cover
24 2 45705 Spacer 1 3-106 Owner’s Manual

Product Parts

Assembly Instructions

NOTE: Remove tape from Slide Gate Bracket







SCAN QR CODE FOR SPREADER CALIBRATION VIDEO INSTRUCTION

Calibrate the flow control setting. (See figure 18)

  • Move the control lever (A) to the “OFF” position.
  • Slide the control bracket along the control tube until the shut-off plate in the bottom of the hopper is closed.
  • Lightly tighten the hex nuts that fasten the flow control bracket to the control tube.
  • Set the adjustable stop (B) at “5”. Pull the control lever (A) against the stop (B) and verify that the shut-off plate has opened about half way.
  • If the shut-off plate does not open half way, adjust the position of the control bracket until the shut-off plate opens about half way and closes completely. Tighten the hex nuts.

SAFETY INFORMATION

  1. Read the information on the chemical package for instructions and cautions on handling and applying.
  2. Wear eye and hand protection when handling and when applying lawn or garden chemicals.
  3. Never allow children to operate the spreader.

OPERATION

Do not use powdered lawn chemicals. They do not give a
satisfactory or consistent broadcast pattern.

  1. Estimate the size of the area to be covered and calculate the amount of material required.
  2. Set the adjustable stop according to the flow setting recommended in the application chart on this page.
    Also refer to the instructions on the packaging for the material to be spread.
  3. The application chart is calculated for light to heavy coverage at a vehicle speed of 3 mph, or 100 ft. in 23 seconds. Do not exceed 6 mph.
  4. Make sure the control lever is in the “OFF” position.
  5. Fill the hopper, breaking up any lumpy fertilizer.
  6. Start the spreader in motion and then pull the control lever forward against the adjustable stop to the “ON” position.
  7. Always move the control lever to the “OFF” position before turning or stopping.
  8. To ensure uniform coverage, make each pass so that the broadcast pattern slightly overlaps the pattern from the previous pass. The approximate broadcast widths for different materials are shown in the application chart on this page.
  9. For rectangular areas, make two passes across the short ends to create turning areas. For nonrectangular areas, make two passes around the entire border.
  10. When broadcasting weed control fertilizers, make sure the broadcast pattern does not hit evergreen trees, flowers or shrubs.

APPLICATION CHART

IMPORTANT: Minor setting adjustments may be necessary to compensate for humidity and moisture content of the material.

MAINTENANCE

  1. Oil the free spinning wheel once a year or more often as needed.
  2. Oil the nylon bushings in the frame tube once a year or more often as needed.
  3. Apply a light coating of grease to the gears as needed.
  4. Before each use make a thorough visual check of the spreader for any bolts and nuts which may have loosened. Retighten any loose bolts and nuts.
  5. Make sure the tires are adequately inflated. Do not inflate beyond the maximum pressure printed on the tire.

WARNING: Over-inflated tires can explode, causing serious injury. To avoid injury, NEVER inflate tires beyond the maximum pressure printed on the sidewall of the tire. ALWAYS use a hand pump to safely inflate tires.

STORING
  1. Empty the spreader after each use, storing left over material in its original bag.
  2. Rinse the inside of the hopper and the exterior of the spreader and dry off before storing.
  3. Store in a clean, dry area.

Customer Support

THANK YOU FOR YOUR PURCHASE!
Without your product review, we don’t exist.
If you are happy with our quality products & service, please take just a moment to leave positive feedback and a short review of our product on our website or your retailer’s website.

Not totally satisfied?
If you have any issues, don’t hesitate to contact us. We make mistakes sometimes, but please give us the chance to make it right before leaving negative feedback against our product.

Customer Care
M-F 7:00 a.m. – 5:00 p.m. CST
800-448-9282
www.agri-fab.com

]]>